Database Users

Stuck in bootloader after failed flash

Hi, got some problems with one of my employes Herald (not simlocked or anything).
It ended up on my desk after complaints about it rebooting by itself every minute or so. I figured I could sort it out by upgrading to wm6. Wen to HTCs website and downloaded the official RUU (HTC_P4350_SVE_4.17.413.2_4.1.13.44_02.94.90_Ship.exe). Everything went along fine and I left it upgrading on my desk and went for lunch.
When I got back it said that the update had failed and I followed the recover function but without success.
Now Im stuck in bootloader mode, and when I try to update it again the current image version is listed as blank and I get to about 1-2 percent before it shuts down and gives "ERROR [244]: INVALID MODEL ID".
Any suggestions on what to do?

Further information...
IPL 4.17.0001
SPL 4.17.0000
When i do a hard reset, after it says format complete it boots up and freezes with a green gradient across the screen.

You can try using USPL or HARDSPL to flash.
The USPL will get around CID locks
This is from ivan's A Herald's Guide to Flashing Aserg, USPL and HARD-SPL - xda-developers
II. How do I flash an NBH file?
Warning: To use the NBH ways, you MUST have a SPL of 4.0 or higher. If you have a lower SPL, you WILL brick your phone.
a. USPL
Step 1. Download Herald-USPL-Beta3.
Step 2. UnZIP the file into a folder on your Desktop. Let's call it "MyFirstROM" for simplicity's sake. Notice that there is a folder called RUU within this folder now. Keep that in mind.
Step 3. Download your NBH file and unZIP or unRAR it into that RUU folder. Make sure that that NBH file ends up in the RUU folder, not within a folder inside the RUU folder.
Step 4. Place your phone into flightmode.
Step 5. Go back to the MyFirstROM folder and then run USPL.exe
Step 6. Follow the directions on the screen. EXACTLY.
Your screen on your cell phone will go white around the 75% part of the "second step" now.
ActiveSync will LOOSE its connection.
Step 7. One step 3 on that black window, the RUU flasher will pop up. Just follow the steps.
That's it. Welcome to the flasher's world.

Thanks for the reply,
First, I cant get activesync to find the phone, only evidence of contact in between the phone and PC is that its listed as [Windows CE USB Devices+PocketPC USB Sync] in device manager. I tried to uspl flash with ASERG.8, and it stops at "STEP 1/3...."
I downloaded mtty to see if it could connect, and it did.
Any further suggestions on what might work!

uninstall..reset.. clean install would probably get activesync to work w the phone..

Reinstalled activesync without any change. And soft/hard reseted everything…
Tried to flash via sd as per instructions in another thread, got to "checking SD contents" and then straight to triple-color bootloader.
Help me please! ;D

Cant help getting the feeling that Im completely screwed...
Cant get activesync to recognize it, only way to get it to light up is via bootloader (camera + reset button), everything ive tried to flash it with hangs almost instantly.
As a complete novice my guess is that the current rom is corrupted and I badly need advice on how to go on. The sd-flash seems quite logical but I cant get it to work. Ive tried to overwrite my sd with 00-values in winhex and then placing the original ruu [HERAIMG.nbh] (through windows, is there a way to write data with winhex?) on the card without any success.
Any suggestions on what to try is much appreciated.

Sounds like the SPL got corrupted or partially written only... sorry. Repair center time. You can also placing your Stock RUU's nbh file into your SD card and renaming it to... umm.. I forget... and then flashing FROM the phone.

facdemol said:
You can't simply place the rom file to the card and hope the device will read it in this way. In my time working for pda service, we used WINHex to format the card (to RAW-unformatted) and then we wrote the rom file in RAW format to the card. Your card looks like an endless stream of hexazecimal values. Only winhex recognises this format, if you insert the card to the computer, it will simply ask you to format it. After inserting this card into the pda, it will start the upgrade . The order of this operation was, as I remember, to fill the card with 0000 values (there is an option in WINHex, a kind of format) then write the rom file to the card in RAW mode. Then insert the card to the device.
Click to expand...
Click to collapse
Thanks for the reply, before giving up and sending it in for repair I would like to give the sd-flash a proper try... So far Ive managed to format the card with winhex but I cant really figure out how to write to the card in raw format. Could anyone point me in the right direction?

i managed to do the steps said above ... formated the card in RAW format etc but still the phone won't turn on ... it will only stay in bootloader ...

diabolic53 said:
i managed to do the steps said above ... formated the card in RAW format etc but still the phone won't turn on ... it will only stay in bootloader ...
Click to expand...
Click to collapse
Care to enlighten me on how you did that?

I've been reading a lot lately.. I wonder if the phones are savageble... something about flashing but bypassing the radio check... Also, the universal has an RUU that bypasses any checks before it flashes... this would be great for us to have... I'm asking around...

g4rwin said:
Care to enlighten me on how you did that?
Click to expand...
Click to collapse
whell i opened the mem card with winhex filled all the blocks with 00 and then i opened the nbf file also with winhex and copied the content in hex format on to the card ....but still no success ..

ivanmmj said:
I've been reading a lot lately.. I wonder if the phones are savageble... something about flashing but bypassing the radio check... Also, the universal has an RUU that bypasses any checks before it flashes... this would be great for us to have... I'm asking around...
Click to expand...
Click to collapse
if you find it please tell us about it cos a lot of phones are getting bricked ...

If I'm correct, you told us a few post above thisone you placed your SD card with the imghera.nbh and got "checking sd conents" and then it went to bootloader.
As far as i can recall you need to get your Herald into bootloader first and then place your SD card with the IMGHERA.nbh file on it. Then it should start reading the image from, your SD card.
Judging from your first post you haven't been using the asigned RUU from the HTC website if this was your first rom flash to WM6 and you got a vendor error. Try to convert and use that one when you flash from sd card.

jappo01 said:
If I'm correct, you told us a few post above thisone you placed your SD card with the imghera.nbh and got "checking sd conents" and then it went to bootloader.
As far as i can recall you need to get your Herald into bootloader first and then place your SD card with the IMGHERA.nbh file on it. Then it should start reading the image from, your SD card.
Click to expand...
Click to collapse
Ive tried all possible ways, if I pop the sd card in while already in bootloader, nothing happens at all.
jappo01 said:
Judging from your first post you haven't been using the asigned RUU from the HTC website if this was your first rom flash to WM6 and you got a vendor error. Try to convert and use that one when you flash from sd card.
Click to expand...
Click to collapse
Ive been trying to flash with the WM6 RUU I downloaded from HTC's site (the one that bricked it) since that is the only local (swedish) and official one I could find. Have I misinterpreted it all and the only thing that could do the trick for me is WM5.1?
Ive also been trying to contact the HTC service dept for over a weeks time ending up in a deadend overfilled voicemailbox - meanwhile my warrantyperiod ran out... Any suggestion on what to do?

duprade said:
You can try using USPL or HARDSPL to flash.
The USPL will get around CID locks
This is from ivan's A Herald's Guide to Flashing Aserg, USPL and HARD-SPL - xda-developers
II. How do I flash an NBH file?
Warning: To use the NBH ways, you MUST have a SPL of 4.0 or higher. If you have a lower SPL, you WILL brick your phone.
a. USPL
Step 1. Download Herald-USPL-Beta3.
Step 2. UnZIP the file into a folder on your Desktop. Let's call it "MyFirstROM" for simplicity's sake. Notice that there is a folder called RUU within this folder now. Keep that in mind.
Step 3. Download your NBH file and unZIP or unRAR it into that RUU folder. Make sure that that NBH file ends up in the RUU folder, not within a folder inside the RUU folder.
Step 4. Place your phone into flightmode.
Step 5. Go back to the MyFirstROM folder and then run USPL.exe
Step 6. Follow the directions on the screen. EXACTLY.
Your screen on your cell phone will go white around the 75% part of the "second step" now.
ActiveSync will LOOSE its connection.
Step 7. One step 3 on that black window, the RUU flasher will pop up. Just follow the steps.
That's it. Welcome to the flasher's world.
Click to expand...
Click to collapse
Hi I try tu patch IPL/SPL with hard spl but with error, now my herald stuck in boot mode. IPL/SPL 1.09.0001. He probbably is from some russia operator (rusian diacritics on keyboard).
How can I try to make him alive?

CAB problems

Hello, i am trying to HardSPL my Tmobile wing. I was told to install thre cabs but i cannot. When i try to install them it says "installation was unsuccesful". Is it possible to flash my phone without it or ues USPL or something. Any help would be appreciated.

what cabs do you mean, are you talking about the yang cabs, please explain

How to HardSPL
livndeadgrl13 said:
what cabs do you mean, are you talking about the yang cabs, please explain
Click to expand...
Click to collapse
The three that you have to install, of course! Here's an amazing guide by Apreincher, with the CAB's included. Try re-downloading the CAB's and installing them. Tell us the specific errors that you get, too!
Steps to flash using HardSPL: (PDF Version)
It is a good idea to flash back to stock ROM just to be safe. If you are using a T-Mobile Wing you can download it from T-Mobile or from this guide. If it's a herald you can download it from this guide.
It is important that your IPL is 4.xxx or Higher. If it is not, do not attempt a HardSPL it WILL brick your phone. You can find out the IPL by going into Bootloader:
While holding the camera button do a soft-reset by pressing the stylus into the reset hole next to the volume slider. Release the reset switch while still holding the camera button. A colored screen will come up listing your IPL and SPL. If next to IPL it says 4.xxx or higher, proceed to step 2.
Reset back into your normal phone OS.
Go to Settings- Connections- USB to PC and check the checkbox on that page.
Install the 3 CABs in this order:
Canon Yang.cab
ASerg Policies.cab
Disable Security.cab
Soft reset the phone.
Download the HardSPL folder, extract it, and place it on the Desktop.
Run ROMUpdateUtility.exe located in the HardSPL folder. Update the ROM using the steps on the screen. The screen will become white, but wait until the phone reboots itself. It could be 10-15 minutes.
Phone should boot back into some strange looking ROM. This is the HardSPL ROM. So far so good.
Check your SPL by going to bootloader again. If it says 4.70.yang, you are good as gold and HardSPLed.
Okay so now how do I flash after I'm in HardSPL?
There are actually two ways to flash while you are HardSPLed. You can use the flash center method or the SD card method. Most LZX and Micro ROM's require you to flash through the SD card method.
Flash Center with HardSPL:
Open the HardSPL folder and remove the .nbh file that is located in there. Replace it with the .nbh file you downloaded with your favorite ROM.
Run ROMUpdateUtility.exe
You've installed a custom ROM on HardSPL.
Flash through SD Card with HardSPL:
Unfortunately, sometimes this can be a bit more complicated. Make sure you use an SD card and not an SDHC card.
Your storage card will hopefully be lower than 4 GB, or else it might have trouble locating the file. If your storage card is larger, you can partition it to be smaller. Also, no SDCH cards will work.
You must format that storage card to FAT32.
Now, you download the ROM (and uncompress it if it’s a .7z, .rar, or .zip file).
Place the downloaded and uncompressed ROM file (.NBH) into the root of your storage card. Also, you must rename it HERAIMG.nbh. (Captialized)
Put the SD Card into your phone, and with your phone turned on, hold the camera button down. While holding the camera button, press and release the soft reset button. Keep holding the camera button until a new, white screen appears.
If it displays a white screen with blue text that says Checking SD contents and then Update Image proceed to step the next step.
If it immediately goes into the colored bootloader screen, it appears your phone's bootloader is not finding your SD card. Some SD cards require special formatting for some reason. Plug the SD card into your computer using an SD card reading and right click on Computer and click Manage. Click Disk Management on the right pane. Select the SD card from the list and right click and select Format. Under Allocation Unit Size, select 4096. Format and ignore any errors. Proceed with steps 2-4. If it does not work even with this adjustment, your SD card might be too slow. Or you have a SDHC card which isn't easily recognized by bootloader.
This screen that you’re on will have a white background, with blue letters. It will search for your HERAIMG.nbh file, and once it finds it, it’ll give you 10 seconds to answer yes.
To flash the ROM, when it asks you if you want to flash this, press down on the volume slider. Weird, eh? Just do it.
Now, let it flash for a good 10 minutes.
Success! Press any key. Press down on the volume slider again, and you’re on the color screen now. Hold the power button to turn off the phone, and then turn your phone back on. Welcome to your new ROM!
If you are already HardSPL and something happens and flashing doesn't work and you find that your phone appears to be off and won't turn on. Don't panic. Go into Bootloader and use the Flash Center directions to flash a ROM.
--------Thanks to Apreincher for the AMAZING write up!!!!!!!!!!!!!!!!

I tried it just says installation was unsuccesful

afo88 said:
I tried it just says installation was unsuccesful
Click to expand...
Click to collapse
Which CAB and what order? Give us more info.

The cabs posted in the tut u gave me
1. Canon Yang.cab
2. ASerg Policies.cab
3. Disable Security.cab
Ive even tried them from another download source. I tried it in the or der that was said it just says "installation of ......... was unsuccessful" and delets the CAB. I also noticed that when i go to add or remove programs noyhin shows up on the list.

HTC HD2 stuck at boot loader... help please.

Hi all,
Before I post here I have googled over the internet looking for a solution and i have read alot but no success, i have tried many different suggested solutions but all have failed, so that I'm here to ask who have faced a similar situation of me.
My HTC HD2 was having SPL-1.42 with its original stock ROM, then I decided to upgrade for a cooked ROM so that I installed the HSPL then it became SPL-1.42 HSPL, that was fine then I'm were able to upgrade to any cooked ROM, I have flashed my device with many different ROMs even the stock ones, every thing were very fine till I upgraded to the stock ROM of leo 2.10 "RUU_Leo_1_5_TMOUS_2.10.531.0_Radio_Signed_15.34.50 .07U_2.08.50.08_2_Ship" by via the MicroSD card and now stuck with the SPL-2.08 as shown in the attached photos.
I tried to flash again using the EXE file from my PC but it take very long time the fail even with the original stock ROM of my device, and I tried to flash using the SD card but it take very long time just showing a white screen labeled "loading..." and no more activity.
I attached some photos showing the problem.
I know its my fault because I did not read the warning in the text file that included with the ROM folder "Do not flash using the MicroSD"
So that, I'm looking for a solution... please help..
any help will be appreciated.
Thanks in advance..
Note: pardon me about my poor English.

xda_q8 said:
Hi all,
Before I post here I have googled over the internet looking for a solution and i have read alot but no success, i have tried many different suggested solutions but all have failed, so that I'm here to ask who have faced a similar situation of me.
My HTC HD2 was having SPL-1.42 with its original stock ROM, then I decided to upgrade for a cooked ROM so that I installed the HSPL then it became SPL-1.42 HSPL, that was fine then I'm were able to upgrade to any cooked ROM, I have flashed my device with many different ROMs even the stock ones, every thing were very fine till I upgraded to the stock ROM of leo 2.10 "RUU_Leo_1_5_TMOUS_2.10.531.0_Radio_Signed_15.34.50 .07U_2.08.50.08_2_Ship" by via the MicroSD card and now stuck with the SPL-2.08 as shown in the attached photos.
I tried to flash again using the EXE file from my PC but it take very long time the fail even with the original stock ROM of my device, and I tried to flash using the SD card but it take very long time just showing a white screen labeled "loading..." and no more activity.
I attached some photos showing the problem.
I know its my fault because I did not read the warning in the text file that included with the ROM folder "Do not flash using the MicroSD"
So that, I'm looking for a solution... please help..
any help will be appreciated.
Thanks in advance..
Note: pardon me about my poor English.
Click to expand...
Click to collapse
Heya i think ur stuck now on that SPL 2.08 havent heard any1 succeeding in putting hspl on it atleast from what ive read.
The cause is because u flashed that Tmous ROM trough MicroSD which overwrites the hspl.
I think if u had read the stickies more carefully this could be avoided but u can still flash Tmous roms some1 correct me if im wrong. hope this helps a bit

Thanks for replaying,
yeah you are right I have to be more careful but now its done and stuck with SPL 2.08.
anyway, I have tried to falsh it using Tmous ROMs but it faild, it says "this device is not suitable for this ROM" then exit, by the way, my device is the Asia version and I tried to flash it using the new officially updated ROM from htc.com but it also failed, it take very long time more than 15 minutes with no activity the I disconnect the USB from the device to save the battery charge, I'm afraid to stuck with a dead battery. When I disconnect it the upgrading software on my PC asking me to restart the device and reconnect it again then I did, the official upgrading software recognise the device then start to flash it but it stuck at beginning of the flashing process it just change the screen of the device to the back background with the progress bar its reading 0% and take very long time then i disconnect it.
by the way, is the any way to downgrade the SPL to 1.42 ?
any help please..
Thank you.

Last week I also face this problem. But I'm not using SD card to flash the room.
However, I backup my sd card then format the card, it become will afther this.

Same thing happened to me. This is what I did, removed the battery for about 10 seconds and flashed the original ROM. Then reflashed HSPL. It worked for me.

Thank you all for replaying..
I tried to do as you did but no success at all.
well, what next ?
Thank you

silentP said:
Same thing happened to me. This is what I did, removed the battery for about 10 seconds and flashed the original ROM. Then reflashed HSPL. It worked for me.
Click to expand...
Click to collapse
i believe to try to flash Original Rom from SD Card. not from PC.
i personally save my stock rom in SD card for future use in case of emergency.

Thanks for replaying
I tried to flash using the stock ROM is SD card but it failed, it shows a white screen with a "Loading..." word only, no activity.
Any help please..

You must use GoldCard repaired your device .Look here (Post 31 & 41) Repaired (with any Goldcard ) HD2 damaged when the flash rom TMOUS with memory card :
http://forum.xda-developers.com/show...=640183&page=4
You must change Tmous 2.07 ( in guideline article ) replaced by your ship rom 2.10.

same happened to xmoo....just letter xmoo about your problem...i hope he can help you....

ancola66 said:
You must use GoldCard repaired your device .Look here (Post 31 & 41) Repaired (with any Goldcard ) HD2 damaged when the flash rom TMOUS with memory card :
http://forum.xda-developers.com/show...=640183&page=4
You must change Tmous 2.07 ( in guideline article ) replaced by your ship rom 2.10.
Click to expand...
Click to collapse
Ok this is solution for that problem

no success yet..
but i'm confused about how to use the goldcard ?
I tried to you the attached goldcard.img from the post Id=640183&page=4 but no success.
is the goldcard.img dedicated to a specific device based on its CID ? or it can be used for any device ?
Thank you

Surely XDA Mods should take down the SD card method as there are about 10 threads a week of flashing the 2.10 ROM via SD card and getting stuck cause they don't read enough before hand - if the SD card method isn't there people won't brick their phones!!

{Solved} HTC HD2 stuck at beet loader...
Hi all,
finally I got my device running
by flashing it using Goldcard method, I bought the PSAS software and flashed it using Tmous 2.10 and now it is running fine.
well, the steps as the following:
1- getting the CID of the SD card that you are going to use for flashing you device, I used linux OS to get the CID of my SD card by:
linux host #>more /sys/class/mmc_host/mmc1/mmc1:*/cid
that will give you the CID of the SD card.
2- Start the PSAS software and must be registered then go to Calculations/Generators then select Generate HTC goldcard.
3- then click "Save Goldcard Image to file", rename it whatever you wanna name for example "goldcard.img".
4- Use HxD Hex Editor, then select Extras from the menu then Open disk image..
5- Use HxD Hex Editor, then select Extras from the menu then Open disk...
6- then click on "goldcard.img" tab then select the lines from 00000000 to 00000170 all the file content by high lighting it, then select Edit -> Copy.
7- then go to the disk tab the containing the sd card, then select the same addresses (00000000-00000170) then Edit -> Paste Write, then save the new content.
8- copy a leoimg.nbh to the SD card, its recommended to get it from the ROM that bricked your device. I'm used Tmous 2.10.
9- insert the SD card into your device then boot it to the bootloader by holding the volume switch down while your switching the device on.
10- wait for the menu to appear and follow the instruction to complete.
Thats work from me and should work for you.
by the way, I flashed US Tmous while my device is Asian.
Thank you all
and
Best regards
if you have your CID I may help you to generate the suitable goldcard.img for your device.

I think I've read that even though you are stuck on spl 2, now that you have it running you should be able to flash roms with sspl but you won't be able to change the radio.
HTML:

till now I'm not sure about the radio, any way, I'm trying to hack it, i successfully initiated the process of radio upgrading but it failed at 99%.
we gonna do it one day...

EddyOS said:
Surely XDA Mods should take down the SD card method as there are about 10 threads a week of flashing the 2.10 ROM via SD card and getting stuck cause they don't read enough before hand - if the SD card method isn't there people won't brick their phones!!
Click to expand...
Click to collapse
I tought I read througout numurous posts that the SD method is the prefered way to go?
xda_q8 said:
Hi all,
finally I got my device running
by flashing it using Goldcard method, I bought the PSAS software and flashed it using Tmous 2.10 and now it is running fine.
well, the steps as the following:
1- getting the CID of the SD card that you are going to use for flashing you device, I used linux OS to get the CID of my SD card by:
linux host #>more /sys/class/mmc_host/mmc1/mmc1:*/cid
that will give you the CID of the SD card.
2- Start the PSAS software and must be registered then go to Calculations/Generators then select Generate HTC goldcard.
3- then click "Save Goldcard Image to file", rename it whatever you wanna name for example "goldcard.img".
4- Use HxD Hex Editor, then select Extras from the menu then Open disk image..
5- Use HxD Hex Editor, then select Extras from the menu then Open disk...
6- then click on "goldcard.img" tab then select the lines from 00000000 to 00000170 all the file content by high lighting it, then select Edit -> Copy.
7- then go to the disk tab the containing the sd card, then select the same addresses (00000000-00000170) then Edit -> Paste Write, then save the new content.
8- copy a leoimg.nbh to the SD card, its recommended to get it from the ROM that bricked your device. I'm used Tmous 2.10.
9- insert the SD card into your device then boot it to the bootloader by holding the volume switch down while your switching the device on.
10- wait for the menu to appear and follow the instruction to complete.
Thats work from me and should work for you.
by the way, I flashed US Tmous while my device is Asian.
Thank you all
and
Best regards
if you have your CID I may help you to generate the suitable goldcard.img for your device.
Click to expand...
Click to collapse
I also bought PSAS and used my old TP to goldflash the card. Then flashed it with the TMOUS ROM using SD method. After that it game back to life and only way to flash other roms is using sspl. Only thing now is that I'm stuck with this TMOUS initial splash screen.

Also you can change the splash screen using SSPL,till now you can change what ever you wanna change using SSPL except the radio and SPL flashing.
now i'm looking for flashing the radio with some how.

tamAyT:
SD card method should be used a last resort and only if you know what you're doing - it's a million times easier to use HSPL and ActiveSync as if it fails it's easy to recover. I've never used the sd card method and after reading what it can do if you don't read into the ROM well enough it's not worth the hassle IMO

BladeKnight said:
same happened to xmoo....just letter xmoo about your problem...i hope he can help you....
Click to expand...
Click to collapse
HAHAHA.
For me changing the first 2 00 in de hex edit of the goldcard to 11 fixed the issue.
Radio 2.08 is greate.. SPL 2.08 is greate... So no problems a.t.m., if I need a stock rom I use SSPL...
But then again I hope someone comes with HSPL 2.x tho.

PLEASE HELP : HD2 broken - need Goldcard - i can make small DONATION

Hi,
first, my HD2 Leo is a french one (SFR operator).
i put lot of ROM without any problem. The last one was the Chucky ROM.
i try to put the "Cruzer 4th" : but it was a ROM based on 3.14/SPL 3.03 official HTC ROM : it broke my HD2.
i try to flash with a old HTC ROM (1.42 / 1.66 ) without success... i try with a old SFR ROM, without success. ("ID invalid vendor" message)
the only solution to get back a old SPL ( 1.42 ) seems to make a goldcard.
so: i search a goldcard for my HD2, and someone who can help me little.
i have money problem, i can't buy a new HD2 (too expensive)....
but i can make a small DONATION via PAYPAL to thanks the guy who help me to recover my HD2.
THANKS IN ADVANCE
NOTE: i don't have any access to windows mobile on my HD2. only the red/green/blue/white screen at boot. only boot via SDCARD can be OK. USB transfert seems be ok.

hint
you can flash from SD Card any firmware, even official with replacing SPL, here is the procedure
- Take any "RUU_signed.nbh" from a ship ROM and copy it to SD card.
- Rename it to "leoimg.nbh"
- Reset the device while pressing the volume down button.
I do not have experiences with it, so take it just as a hint, to be sure maybe you should try to check some threads about it, for example start with this one:
http://forum.xda-developers.com/showthread.php?t=820038&highlight=rename+ruu_signed.nbh
anyway, if you insist on the goldcard, here is the right thread for you, just put your CID number and wait
http://forum.xda-developers.com/showthread.php?t=650719

thanks a lot pedro.
i donwload now the SFR ROM... but i think it will don't work..wait and see.
about golden card, i think it will don't work , because i saw i must launch a file (enablerapinew.cab) from my HD2 windows mobile... but i can't !! : i have only the boot screen now (red/green/blue/white)

ok, i try to flash with my original ROM from SFR... not work.
- USB way : HTC flash indicator stay always at 0%
- SDCard way: have only the "loading" message advitam

5tef said:
ok, i try to flash with my original ROM from SFR... not work.
- USB way : HTC flash indicator stay always at 0%
- SDCard way: have only the "loading" message advitam
Click to expand...
Click to collapse
This article can help you get a Goldcard.
http://forum.xda-developers.com/showthread.php?t=825397
Hope this helps,
Regards
Sean

Renaming a,stock nbh to leoimg.nbh should work every time. Make sure you SD is formatted to fat32 then put the leoimg.nbh on SD card. Remember to extract a stock Rom from HTC website using 7zip or similar and only rename the ruu_signed.nbh hope it works
Sent from my HTC HD2 using XDA App

[Q] How to use a Goldcard

Oke guys here's my queston.
First look at:
http://forum.xda-developers.com/showthread.php?t=939763&page=3
My radio is probably bricked, so now i'm trying to use a goldcard:
I managed to get the CID of my SD card.
Reversed the CID of the 2 Gb is: 009b000a6daf00804732305553445303
With a little help of this forum i now have a goldcard and put an original LEOIMG on the goldcard.
Still no solution, the bootscreen flashes off/on 1 time and then returned into bootscreen. No attempt of flashing seen. What went wrong??
Thanks in advance!

first the obvious questions, (quite often its somethign dead simple) ,
you extracted ruu_signed.nbh and didnt just rename the whole .exe to .nbh?
How did you write the .img to the card? ? you
How did you get the CID?
let me have the two CIDS (dont reverse them or anything, just as you got them) and an email address and ill make you an image for each disk, that way you have three to try.
Magazijn said:
Still no solution, the bootscreen flashes off/on 1 time and then returned into bootscreen. No attempt of flashing seen.
Click to expand...
Click to collapse
on a normal sd card, this usually indicates either wrong stock rom being used (sure the rom you are using is for your region AND carrier?((if locked)), or an sd card that isn't set up right (freshly format it, FAT32 )
It might point to the goldcard image being wrong, or incorrectly written to the card.

I extracted the original HTC HD2 dutch rom, took of the ruu_signed.nbh, copied it to the goldcard en renamed it to LEOIMG.nbh
I got the CID by using a working adroid phone together with the tutorial from "theunlocker.com" (sdk/adb-app en hex-app)
The 2 onreversed CID's are:
1gb
035344535530314780606ca6f10079a6
2gb
03534453553032478000af6d0a009b8e
emailaddress: [email protected]
thanks!

Hey Magazijn if your problem is not a hardware issue then you have the right guy working with you now. Samsamuel will have you up and running again I am sure of it. Just remember though if you are using USB to flash and not SD card then always put your HD2 into bootloader and wait for the USB tben flash this is a trusted method. And don't forget to click Samsamuel's thanks button when he gets you going. Peace.

heh, cheerleader fees in the post.
@OP sorry for the delay, theres a step by step to double check you are writing teh image correctly HERE

Thanks for the quick solution samsamuel, but still the same problem.
After Boot the screen builds up again in boot and that's it.
So i think it's an hardware radioproblem with can't be fixed.
Should a hardware repair help me out?
Last question i used original dutch LEOIMG (winmo 6.5), can i use another (android of winmo) rom?
If yes, which would you prefer.
Again thank for your help, i appreciate it.

hmm, not sure what to suggest. As i said b4, a brief 'loading' then back to bootloader usually indicates the wrong rom. Are you sure your phone is an unbranded dutch phone? did you download that rom with your serial number from the htc website? (it will only let you download correct roms if you use serial)
This shouldnt matter if the goldcard is working, but if you KNOW its the correct rom, it can be discounted as the cause.