Has anyone installed the HC SP300 screen protector - if so does your proximity sensor work.
I noticed today that when i make a call, the device blanks the screen after pressing the send key. Putting it to the face and away does not make the screen come on. I'm guessing its the screen protector as i just did a hard reset and still not working (although it did when i got the phone.
I install the HC Sp300 on my device and the proximity sensor still works fine.
OK thanks.
Guess im going have to remove it to find out if it is the screen protector. If that doesnt work, i guess i have a dead sensor?
I have the same problems. It seems to be working, but with the more light.
I had the problem of the black screen when a call connected.
To solve it, i cut a small section near the 2 small holes in the top left corner.
Now it works as per usual. I think its a case of 'if you dont align the holes on the screen protector precisely', you will get this problem.
Related
hi
As soon as i make a phone call my screen goes off, now on my iphone it used to do this only when the light sensor was covered. to bringthe screen back on I have to press one of the black buttons in the bottom of the phone, is this a fault?
I had this problem after fitting a screen protector. removing it solved the issue for me.
The genuine HTC Screen protectors have 2 holes in for the sensors. I can confirm this does not affect the screen when making a call.
Are you using a screen protector which doesn't have a hole for the proximity sensor etc?
It may be it can't function right as it maybe seeing the protector as something close to the sensor, hence why the screen goes off.
I have a Vidocq screen protection and the phone wake up again when I finish the call...
i tried to search the forum with no results btw
have two cases while receiving/calling with hd2
1. via bluetooth headset - even when the phone is in the pocket some apps starts randomly, even call is disconnected - isn't proximity should cause phone scrren to be blank all time?
2. via the phone - sometimes while talking screen is still dark and pressing eg. home key puts display on. sometimes moving phone away from ear turns screen on.
do you have some or its something with my phone?
I have the same problem, the proximity sensor does not work, I think it works only outside when you have strong light, try it and let me know.
make a call the screen will go off now move it from your face loking up at the sun outside you will see that the screen will turn on.
it works only when I makes a call. when I am getting a call it atays on.
kochav
kochavy said:
I have the same problem, the proximity sensor does not work, I think it works only outside when you have strong light, try it and let me know.
make a call the screen will go off now move it from your face loking up at the sun outside you will see that the screen will turn on.
it works only when I makes a call. when I am getting a call it atays on.
kochav
Click to expand...
Click to collapse
Well you would be wrong then.
It's a proximity sensor, not a light sensor. I just made a call in my darkened room and the proximity sensor functioned flawlessly.
thake the screen protector out or cut it and the proximity sensor will work perfect.
kochavy
kochavy said:
thake the screen protector out or cut it and the proximity sensor will work perfect.
kochavy
Click to expand...
Click to collapse
Wow who would've thought that covering up a sensor designed to sense when objects are close to it would impede its functionality.
Your revelation hepled me fix the microphone on my phone. It wasn't working, and then I realized I had my hand over it!
Yes I have had issues even with the original HTC screen protector which has two small holes directly over the sensors. I finally had to remove it.
Cutting the protector I have not been very successful so far. This creates sharp edges and the protector tends to peel off from that point. For the time being I am relying on the fact that the screen on the HD2 is scratch resistant enough that with normal care it would not get scratched. With over 2 months of use without a protector my screen is still scratchless.
IF it is anything to do with the screen protector, then there are plenty out there that don't have this effect.
I've got a protector on my HD2 and have had it there since just after I got it, so just over 2 months now. The screen protector has worked perfectly, even, kochavy, in the dark, because it detects proximity not light.
I suggest removing any screen protectors and seeing if you still have the problem. If you do, send the phone back as faulty. If you don't, get a better screen protector.
johncmolyneux said:
IF it is anything to do with the screen protector, then there are plenty out there that don't have this effect.
I've got a protector on my HD2 and have had it there since just after I got it, so just over 2 months now. The screen protector has worked perfectly, even, kochavy, in the dark, because it detects proximity not light.
I suggest removing any screen protectors and seeing if you still have the problem. If you do, send the phone back as faulty. If you don't, get a better screen protector.
Click to expand...
Click to collapse
do you have the original HTC screen protector with the two holes? there are some protector that does not cover the top of the phone and leave the two sensors out from protection.
kochavy said:
do you have the original HTC screen protector with the two holes? there are some protector that does not cover the top of the phone and leave the two sensors out from protection.
Click to expand...
Click to collapse
No I don't. The one that came with it never please me much, so I bought some better ones.
The protectors I have don't have any holes for the sensors at the top, but like I said, it just works perfectly. There's a lot more to this issue that just the screen protector, as some people have reported that it works perfectly when they ring certain number, but not when they ring others. From what I've read on other threads, this is commonplace for people who are having this problem, so it's obviously not an issue with their screen protectors. It sounds like a software issue to me, but since it can't be identified as such, they should just return their phones as faulty and hope the replacement doesn't have the same issue.
It would be interesting to know if the people with the described issue have upgraded the ROM to 1.66, as this seems to have fixed a whole slew of issues.
Sensor works by reflecting infrared light. There is small IR lamp with IR detector nearby. You can check that by looking at the sensor through some digital camera or camcorder, whose are usually sensitive to this light. Don't forget the phone must be in call, otherwise the sensor is turned off.
I think the sensor itself is OK. But there seems to be some relationship with guess what .. G-sensor ! Once I found the screen just won't go off during call, and it was when I was lying during the call, and I was holding the phone upside down portrait style.
But as I turned the phone to normal position (normal portrait) and back, it started to work with no problem.
I only had problem with proximity sensor once since then .. but rotating the phone up and down helped again.
I think this needs more investigation .. if you encounter the problem try this.
wanted to know if im the only who is having this issue with phone calls. even without a case when i move the phone away from my ear it doesnt respond, i still get the black screen. i press the power button but the screen just flickers and doesnt do anything at times. is it the rom? my phone? i also faced it into the light and sometimes it comes on sometimes it doesnt.
figured it out.... went through 4 screen protectors and got the cut out right for the last one. seems the proximity sensor is blocked by the screen protector. almost listed my phone on ebay. haha
Hi,
Lately i have been noticing that the proximity sensor on calls on my s5 is not working properly. Once i answer/make a call, when i place the phone in my ear it shuts down the screen but the problem is when i take it away from my ear, the screen doesn't turn back on.
I tried the the testing menus (*#0*# or something like that) and when i placed my finger close to the sensor it detected, going green and vibrating but it doesn't go away from that state.
The only thing that changed was that i applied a glass screen protector a few days ago and im thinking it could be that, but its strange because its only when i back away from the screen that it doesn't register, so i don't know if that or not. Also, the protector is properly aligned and the edges are not on top of the sensor.
Anyone experienced this on their s5?
griffin_1 said:
Hi,
Lately i have been noticing that the proximity sensor on calls on my s5 is not working properly. Once i answer/make a call, when i place the phone in my ear it shuts down the screen but the problem is when i take it away from my ear, the screen doesn't turn back on.
I tried the the testing menus (*#0*# or something like that) and when i placed my finger close to the sensor it detected, going green and vibrating but it doesn't go away from that state.
The only thing that changed was that i applied a glass screen protector a few days ago and im thinking it could be that, but its strange because its only when i back away from the screen that it doesn't register, so i don't know if that or not. Also, the protector is properly aligned and the edges are not on top of the sensor.
Anyone experienced this on their s5?
Click to expand...
Click to collapse
You have to change the proximity sensor or cancel it(cutting the flat)
I ended up removing the screen protector and it went back to working properly =/ I can't really put it back on now because it attracted specks of dust and it doesn't glue well now =/
Cutting it flat means it deactivate it? Because i find it useful for phone calls
griffin_1 said:
I ended up removing the screen protector and it went back to working properly =/ I can't really put it back on now because it attracted specks of dust and it doesn't glue well now =/
Cutting it flat means it deactivate it? Because i find it useful for phone calls
Click to expand...
Click to collapse
Cutting it means deactivate fully, even in calls display stay on.
Is there anyone else encountering the same issue with me?
I realize my proximity was not working when the screen wont turn off during the call when using the earpiece. I did went into the CIT and performed the proximity sensor test and the proximity sensor seems not even reacting.
Is there any chances that it could be the tempered glass screen protector affecting the sensor to work normally? I found that the phone is eventually something they called it "Virtual Proximity Sensor" so i kinda clueless on fixing this.
Mine is working through the glass.
Apply all the updates, happened the same to me until i applied system updates.
The reason of it is you glass protection.
Works for me. Unless I am in another app whole in call
I face the same problem
The proximity sensor seems to be located on the top right (next to earpiece) literally invisible to at least my eyes. Make sure you have no bubbles in that area from screen protector install and if there's a smudge from your fingerprint it might block the sensor thinking it is placed near your ear. So clean it if it doesn't work properly. Maybe screen protectors with black borders like the Nillkin one require 100% accuracy when applying them?
I do have a line all the way around my phone where my screen protector has and will not stick to the phone.
Can't comment on plastic screen protectors.
I have the same issue on my MI9T Pro. Tested with CIT (4 times click on kernel version appear this tool to check the hardware). First time the sensor worked fine (5.0 to 0.0), second time it was stuck on 0.0
Then I reboot the phone and it has fixed by itself, but this is a recurrent issue, I couldn't solve. Someone knows the real solution?
I have the same problem , i don t know if is a software problem , i think is more a hardware problem . The sensor worked fine ( i think ) until i installed a temperd glass . When i put the glass " perfect " the sensor not worked ...then i moved the glass down , and is working , but not 100 % . In call i must find a position , an in my pocket not seek to work . I use a Wozinsky Super Tough for Xiaomi Mi 9T & Mi 9T Pro, Full Screen, Full Glue.
For me screen protection is very important , and i make thia compromise for now . I Hope to find a better temperd glass !
+1 for the proximity sensor problems... I had 10.3.15, now chaned over 10.3.11 and the same. I have screen protector from Samsung A50. Sensor is going off when I make a call, and didn't came back when I put the phone down.
This is not happening every time, but once in a day/two...
No problem in K20. Using back cover and .2mm plastic screen protector
I think the problem is with temperd glass , mine have black border and i think that is the problem !!
I have the same issue. But I noticed this only happens for the incoming calls and not for the outgoing also I noticed when this happen it's like sensor doesn't wakes up but I have to say that I have screen protector also. I read in a forum from Spain that several users have the same issue even without screen protector.
For the incoming calls, I notice a lot of times that the phone/smart watch is ringing, but the screen is not turning on. Even when I unlock the phone can see that someone is calling...
Screen protector
I have the same issue. I have a tempered glass with black frame too. The proximity sensor doesn't work when the glass is on. It is a really strange issue.
I have the same issue. I have a Xiaomi mi 9t pro and my proximity and light sensor don't work (same component)
But I have a theory. Like many I have installed a tempered glass previously but I removed it some weeks ago because of a crack. But I didn't replace it with a new one.
But who else used the (included) oil to remove the halo effect around the screen protector?
I used it but I think some oil seeped in the speaker grill and this maybe gives errors on the contacts of the proximity and light sensor!? The sensor is nearby the speaker grill.
I have the same problem... Have phone about a month, I've put glass the same day I bought the phone... Does anyone know where is the problem?
All i can tell you all is how to apply these screen protectors, because at the end of the day it is NOT a hardware issue. (sure, maybe a hardware flaw when using it with an accessory such as a protector)
The best method imo is to use tape or the sticky stickers that should come with the pack, so you end up creating a hinge that should always "close" at the same exact spot when you "open and close it".
Only then should you continue to peel of the film after thoroughly but gently wiping off the dust and marks especially near the proximity sensor. Make sure the phone is "naked" and that you do this in the least dusty environment. Do not waste any time after peeling off the sticker but do not rush and risk messing up the allignment. It should be an even gap/space all the way round of the phone. If you feel like you did everything right and it still doesn't work then next time move the screen protectors ever so slightly downwards.
Refer to my first post on the first page to see my phone's screen protector installed. Guess I can take some clearer pictures and show you. Have used the phone with three cases and zero problems apart from smudging the sensor with my ear a few times.
My first post using text formatting lol
I briefly had your issue, i simply cleaned the top speaker grill.
Can confirm, tampered glass with black borders cause this problem. I removed it and now it works flawlessly.