Anyone else have this problem?
The miniusb port is loose, and I have to wiggle the cable then put something on it to hold it in place.
Anyone tried soldering it back together? I don't think I have the skills to do that, but I'll have to try if it gets worse.
I got the same problem. When it happened to my wife's touch she had to have it replaced AND pay the deductible (the port isn't covered on the warranty)
Related
Hello Wizard Owners,
Last night, while plugging my Cingular HTC 8125 into my charger, I pushed a little too hard, and had the mini-usb held at a bad angle. The furthest left and furthest right charging pins bent and are now broken off inside the phone. The broken off bits have since been lost, and now when I plug in the mini-usb charger--my phone will not charge. Is there anything I can do to replace the charging pins or modify the phone so it will charge properly? Or do I have a nice expensive paperweight now? Thanks for your help in advance.
There is a thread in my siggy discussing this issue. I'd suggest reading through it and see if any of it can help. Beyond that, see if there is someone locally who can fix it. I paid $50 here in Fresno for my usb port to be repaired.
I'm starting to have real problems with my USB plug. At first it would drop charger plugs when it was on the wall, so I put it upside down. But now I can't connect to the PC all the time either. I have to jiggle the plug a bit or even breathe down in it (the moist makes the connection better). Has anybody else had that problem and fixed it in any way? I suppose the plug is soldered on in such a way that it has to go to a workshop, right?
i strongly suggest you to send it for repair or resolder the base of the connection(this is user servicable provided you have some soldering skills) so it doesnt wiggle. i'd probly even suggest to hotglue the plug but before you do so make sure the plug is sitted properly and it does sync
the same thing happened to me and with a bit of jiggle the plug broke off and now its permenently damaged(ie it will never sync via USB again) so far with self repair i only manage to make it charge
i got no idea how to reattach a 10pin mini USB plug to my board and some of the copper tracks looks damaged which means if i send it to the shops, its a $500 repair and a board swap
The USB connector on my Evo is now so loose that I can hear it bouncing around when I shake the phone. USB connection doesn't work at all, no charge or PC connection. I think the connector is detached from the PCB (assuming it was attached to the PCB to begin with).
Obviously I need to fix this thing. Any suggestions? I think I need a T5 screwdriver to open up the case. Don't know if I can reattach the connector w/ a soldering iron?
I'm really disappointed that this thing broke so fast. I don't recall mishandling it.
might be easier to just warranty or return it. can't you return for another one within 30 days. say you got a defective unit.
Yeah I can try the return / repair route but the phone is from Google I/O... I guess it's best to try though.
need help please people.
my phone hasnt been charging properly for a few days now, to get it charging now i have to get one of my missis hair bands and wrap it round my phone and then round the usb cable so it stays in , although today it doesnt want to charge at all now .
ive noticed that the connection in the phone is loose and you can move it round a litle bit,
now the bit i need help with , is do i take the phone apart and try to fix it.?. im thinking of doing this but unsure about taking phone apart ( dont think my phone is under warrenty anymore,) and im guessing the usb connection on the phone is fixed onto a board.
is it worth me trying that or should i just take it to a repair shop ?
take a dry toothbrush, give the usb port a good scrub. dirt often builds up in the bottom of the port and stops the usb plug pushing deep enough to get a good contact.
Have a good inspect of the usb port, bright light and magnifier is good, see if you can see buildup, or a bent connector, or somesuch.
Also look at the usb plug on the cable, its uncommon but not unknown for the metal outer enclosure to open slightly, and make for a weak contact.
Sometimes a cable simply doesn't fit well for no obvious reason, , i have a generic cheap ebay cable that will only work when angled up or down, like yours, but looks perfectly fine, and feels to fit the socket, while the HTC cable works perfectly, so i know its not the port.
If it all looks good, then chances are you have a dodgy connection from the usb port to the mainboard, which will get worse every time you wiggle and bend the cable to get it to work. In this case, you COULD try a repair, but there have been reports on here of some repair shops pronouncing it too fiddly to replace teh usb port, and a new mainboard would be the only other option.
edit - just reread your post and seen that you can wiggle the port. Broken solder, gotta be. Its not an easy solder, so if your a dab hand, then go for it, if not, see above.
Hi iainbp, heresandyboy had this same trouble in http://forum.xda-developers.com/showthread.php?t=903977 from post 16.
It looks tricky!
Just a thought though, I recently bought a cheap phone charger with multiple interchangeable heads for different phones. The microUSB one became difficult to charge with and it took me a while to realise that the metal bit at the end had detached from its plastic casing, and when I plugged it into the phone it just got pushed back into the casing. (got my money back)
Possible with yours?
A few month's ago I'd ordered a LCD screen replacement for my incredible, and so when I got back from work o immediately took out the LCD from the package and started taking out my old broken. For me it was my first time experience replacing an LCD phone screen, anyways back to what I was going to say was when I unplugged the connector for the screen and the motherboard itself, after attempt to plug the connectors back together; the display connector plugged in perfect while the connector for the motherboard didn't do so well. The white piece that covers the PCB Connector, it tears a little bit off and I'd tried to power on the phone, meanwhile it didn't I tried again and things got worst. So I search online for a PCB Connector and see one, so I decided to and try to rip off the PCB Connector and plan to order the PCB Connector. So the part to attempt ripping off the PCB Connector didn't go so well, and stop there before things got worst. Any suggestions how I can replace that? I can't just leave my phone in my room and have to cover in dust. I need my phone back, how can I fix these? I know this thread seems long but I tries but it details for you guys.