I've tried to upgrade my dopod c800 to WM6 through activesync.
my dopod is suddenly dead after error on my PC.
I could go into hard reset page, but it shows "format is failed", and continue with the green screen shows my IPL & SPL 1.09.0001
The way i follow the upgrade was (post #5)
http://forum.xda-developers.com/showthread.php?t=361402
Now, i not able to start up my phone, and my phone only hung at the green screen, can anyone help me to solve the problem?
Related
I was updating my new i-mate SP3 (typhoon) to the latest i-mate ROM 2.4.33.11 which completed successfully but now every time I turn on the phone it goes directly to the bootloader tri-color screen. I tried several times to update the ROM again but it does'nt help. It shows the proccess completed successfully but the phone is still stuck in bootloader mode.
In the bootloader screen it shows the following
IPL 1.00
SPL 2.5.0102
I even tried to flash the ROM through an image of Orange4114_ALL_SPL1010091 on a miniSD card but it gives an error message
"Not allowed update!"
Please help me figure out how to get my phone working again.
Same PROBLEM here HELP..!
Exactly the same problem if anybody can help ..please do.
spl
hi
same problem my sp3
SPL
Same problem on spv c500 stuck in bootloader but with 2.05.0130 SPL
sp3i stuck
Hi all,
I have the same problem, but I didn't try the mini-sd boot.
surfturtle, will you kindly send me the way?
Thanks
Hi guys...
I don't have the Typhoon and don't know if this will work for you, but this is at least how we fix this problem on the Hermes:
Enter into bootloader using mtty.exe and run the command "set 14 0" and "task 8". Phone will reboot and start OS.
If it doesn't work, then try the SD flash method mentioned by surfturtle. Keep in mind that if your device is not superCID the image file should match the CID of your phone (must be an original shipped update from your vendor). This method consist on:
1) extract the rom image from the rom upgrade exe (winrar or cabextract can be used for that) and you'll find a .nbf file.
2) Rename it to TYPHIMG.nbf
3) Format your SD card in FAT32
4) Put TYPHIMG.nbf on the root folder of your SD card
5) put sd card on the phone, and enter into bootloader
6) confirm flashing on screen, and wait until the process is finished (do not reset it, will take about 30min).
Check the hermes wiki if you need more information on any of this.
Good luck!
sp3i stuck
thanks pof,
but where would I get mtty.exe and where will I see "set 14 0" & "task 8"
thanks again.
Re: sp3i stuck
@Tall_Man: See the hermes wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
I-mate ROM
Hi, I did the upgrade through the PC but the device info still shows the old ROM: 2.1.33.13 No error messages and the phone keeps hanging on me.
Is this version of ROM the Arabic one? If not, can someone post or point to where I can download the arabic version? I did not find it on the I-mate website.
Thanks in advance,
I-mate SP3 (?rom 2.1.33.13)
Hi,
after flashing with aWizard debranded ROM my mda becomes a Error.
Now he stops after Softreset by
ipl 2.06
spl 2.06.0000
gsm 02.19.21
os 1.12.2.23
and than he does nothing.
When I Softreset and press Camara Button he goes in 3 Colour Mode. When I connect to USB he writes left at bottom USB.
But I can´t flash him. He shows Error 302.
What can I do ?
MCS
Maybe try a hard-reset ?
Yes I did, but the Problem is the thame.
MCS
s200 G4 is waiting on the "three color" screen after tried upgrade wm5 to wm6.1
i have a qtek s200.i tried to upgrade it wm5 to wm6.1.All was ok and then suddenly something happened.It stopped on the three colour screen.It began to restart itself.It didnt even open for a while.And i take off the battery and left it to morning.Now it's waiting on three colour screen and started to restart again.
i lost my "sync" between pc and i cant do anything.
Any suggestions pls
Did you do HARDSPL first? That's what I did before upgrading my G4 to 6.1
s200 G4 is waiting on the "three color" screen after tried upgrade wm5 to wm6.1 Repl
i did hard reset before upgrade.But i didnt setup a passing rom.
Could it be coz of this?
i have same problem.
g4 chip.
i tired multi wm6 roms but upgrade is not completed.
error window :
Be sure you have followed these steps:
http://forum.xda-developers.com/showthread.php?t=350033
Have luck.
My son dropped his 8525. It is now stuck on a display of red, green, blue, and white bars. A reset and a battery removal do nothing to get it to boot. Is it toast or is there something I can do to get it to boot?
considering this is your 1st post I'm assuming that you didnt have olipro 2.10 as your SPL.....What is your IPL and SPL as this may get you the help you are looking for... And if you do get it going again PLEASE install Hard SPL, Here : http://forum.xda-developers.com/showthread.php?t=296722
Good luck.
P.S. try reading through this, it may help... : http://forum.xda-developers.com/showthread.php?t=369434
The IPL:
IPL-1.04
The SPL:
SPL-2.03
I hope this helps someone.
Someone said they had success with this problem in this thread http://forum.xda-developers.com/showthread.php?t=355884
Read a bit and see if it works but please understand that this really just trying out everything in a last ditch effort to get it working. There may be no hope, so no promises...
If you do manage to get it going again I'd suggest Hard SPLing your phone so it is easier to fix. Hard SPL isn't a guarantee, mind, but it does provide a safety net for when things like this happen...
All the best...
hermes 100 8525 flash problem
hi, i was trying to upgrade a cingular 8525 in the process of unlock,
and it stopped at 1%, and did nothing,
now the phone just go to the 3 color screen,
and says
herm100
ipl-1.00
hem100
spl-1.40.olipro,
what can i do to restore it to normal please,
lacasapc, try to Hard Reset, hold down both soft keys and reset with stylus. If that doesn't work then try this : Flash it to you device while it in tricolour screen. Make sure that your activesync disable & use the latest RUUwrapper.
Open Activesync, select connection settings and untick "Allow USB Connections".
Run the RUUwrapper.exe file for the os you want after connecting the hermes via usb. Chose SPL 1.40 then HARD SPL and then flash the new OS. This should work.
Cheers...
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
brick...
chipis said:
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
Click to expand...
Click to collapse
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Thank for answer me and understand what i ment
Ok what software you recoment?. I do not know if i have a unlocked phone but i do know that i used it with t-moble even that my pocket pc is for cingular, i went to those stores that unlocked phones and that it
Help.
I have a Wizard G4 and I tried to install a WM6.5 ROM (TechTeamup Mega Wizard rom) from the default WM5. I did not put in the hard-spl (as I now read) before I tried to flash. Now when it boots, I go strait to the flash screen (tri-color) screen. I tried ot run the hard-spl-G4 and it says it cannot find a device. I have tried to re-flash back to WM5 ROMs that I have found, however it says it cannont complete "ERROR 296: UPGRADE ONLY, which makes me belive I need a G4 Wizard ROM that is a full (not upgrade). What steps should I take now to revert back to a WM5 so I can re-try the "unlock" hard-spl proceedure to make the phone WM6 compatible?
Anyone have any suggestions?
IPL 2.28.0001
SPL 2.28.0001
Download the original ship ROM for your phone.
Turn the phone off.
Press and hold the Camera key, now insert the USB cable, Keep holding the camera key until you get the boot loader screen.
Now run the ROM update to flash back to WM5.
ricozy said:
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Click to expand...
Click to collapse
I brick my wizard too... What happened was I flashed my own cook of m6r5 it say successful but on reboot, it shows htc logo then stays ay tricolor screen:
IPL 2.26
SPL 2.26
Bootloader wont work..tried many times but I cannot connect to PC...
Tried ricozy post above, can access 3 color... but still cannot connect to PC...
Please help...anyone..
IF u can enter bootloader...connect to pc...u shud c "USB" written in the left bottom corner ...then flash a rom as usual