Hi - I've been searching this forum over and over, but couldn't find solution.
So - I was trying to install new rom using ShellTool and faiiled. Now it only shows boot screen with ipl/spl. I had intalled new rom before and it worked fine.
Also, then I have tried this http://forum.gsmhosting.com/vbb/showthread.php?t=332143 (installing mmty rom, shows that installing is sucessful) but still hangs on blue screen.
Anyone could help please?
Related
Hi
I've got a HTC Hermes that won't boot up properly.
I've had a quick search and can't find to find the exact same proble but apologies if this has already been raised.
I previously flashed my T-mobile ROM with RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.rar.
The problem started when I downloaded a Registry Optimizer from Windows Update. When I started using this my phone was not in airplane mode, and just hangs on the logo screen (this is the gold Tai Edition)
I tried to do a hard reset (this goes to the screen with the four colour bands on it), and then when I reset it again it just switches to the logo screen and stays there. After a while, the screen goes white and stays there
I've got only a basic knowledge of flashing ROMs and when I first flashed my ROM i used Hard SPL and the basic AT&T Windows 6.1 ROM, before using TAI's custom one.
I presume I need to try and re-install the ROM (via the SD card, as Active Sync doesn't recognise the phone)
I was aware of risks whilst using the Registry Optimizer and realise that this is my fault, so I'm not expecting any quick fixes
Would be grateful though if anyone could point me in the right direction, if my phone is recoverable, and not bricked.
Cheers
You flashed a rom for the Kaiser.... You have a Hermes...
Looks like a brick to me....
If you use the sd card method you might be able to fix BUT make sure its a Hermes rom....
Thanks for pointing that out!
I found the thread on how to unbrick a hermes, so should be ok from here..
Hi everybody,
i used the CleanEX Rom for quite a while. Now i flashed another rom.
Strange thing is, i still see a CleanEX Screen, right before the usual boot splash screen (with the radio-version a.o.).
Recently I flashed task29. if i boot now i see the CleanEX-Screen.
How can i get rid of it?
Hopefully someone can help me out.
Greets,
Tiggi
Have you found a fix for this because I had the same thing happen to me. And now I flashed an Energy Rom but I have the Preboot screen of HTC HyperRom every time I boot up.
I think it's called the Pre Boot Splash.
Check it out here
You can also make your own splash using this tool.
Flash with the rom that have original boot screen... it will overwrite cleanEX.
stock boot screen mate
Thank you so much.
Sorry for the late answer.
Hi everyone,
I've recently flash the rom to onyx 4.1 on my elfin. It was working fine for a few minutes. Then I've found it had a problem that it restarts by itself. After a couple restarts, the phone does no longer boot up. It shows "smart mobility" screen for a couple of seconds and turned off by itself. I was able to get into the boot loader and load another rom and it still didn't fix the issue. I was trying to look for other similar posts, but it wasn't successful. I wonder if anyone here have had similar problem before that can give me a hand. Thanks very much for your help!
Jack
This issue was resolved by flashing the original rom.
Please find this link for original rom.
http://forum.xda-developers.com/showthread.php?t=379034&highlight=original+rom
*First I , open the threat under upgrade , no response yet , so trying here , i need help badly *
Hi Guys,
My HTC Universal is almost dead
I had Tomal v12 ROM, tried to install Almost2 ROM, but it stuck on Splash screen , after reflashing several other ROMs problem remained there. also tried MTTY app and enter to bootload and flushed Tomal rom again.
bottom result. now i can't see any thing on my screen , even i cant enter to BootLoader screen by pressing keys.
Screen is totaly black at moment and usb connected to it does not recoginize it as valid device.
Please help me how to come out from this.. and get back my device back working.
how can i enter to bootloader from sd card.?
any help would be appericiated.
Regards,
Khurram
Have a read on my signature link and search for ROM flash from SD/MMC
Hope it helps,
Thanks for direction
i am going towards it , btw are you sure it will be flashed when device is not responsive even no bootloader
Khurram said:
*First I , open the threat under upgrade , no response yet , so trying here , i need help badly *
Hi Guys,
My HTC Universal is almost dead
I had Tomal v12 ROM, tried to install Almost2 ROM, but it stuck on Splash screen , after reflashing several other ROMs problem remained there. also tried MTTY app and enter to bootload and flushed Tomal rom again.
bottom result. now i can't see any thing on my screen , even i cant enter to BootLoader screen by pressing keys.
Screen is totaly black at moment and usb connected to it does not recoginize it as valid device.
Please help me how to come out from this.. and get back my device back working.
how can i enter to bootloader from sd card.?
any help would be appericiated.
Regards,
Khurram
Click to expand...
Click to collapse
The same thing is happening with my HTC Incredible S
any fixes??
Hey guys, I just need a bit of help.
I have looked through other threads, attempting to install a custom bootscreen. I pushed the bootscreen here, and it worked, but with problems. What I wanted to do is to go straight from MagLdr (From Go Go Go1) to this boot screen, but is that even possible? I'm getting the normal blue android bootscreen, and then after plays the custom bootscreen. Why is this happening?
Also, I am attempting to make it play sound at the same time in the instruction in the third post in the above link, but it doesn't seem to work. Is this a limitation in the HD2?
(N.B. I am not talking about the splashscreen on boot that is flashed through custom_ruu)