I have done hard reset and soft resets and still my wifi is not connecting.
Finally my EDGE is working great but wifi not. Whenever I try to connect my SSID is set to "EMC Wireless Internal" channel 11. I have no idea where this cam from but I can not get rid of it. I have a new FIOS Actiontec router with wireless enabled to my network name, channel 10. And Hitchhiker tries to connect but it keeps getting bumped off.
I have gone into MediaNet and turned off the proxy and checked for it to go onto the internet on Cingular GPRS.
I have not had a problem connecting before on wifi. I wonder if the router is a problem here, or if my phone settings are screwed up.
And ideas?
Thanks
The WiFi - EDGE contengency
*The Bad News*
By default, if EDGE/GPRS is configured to work, WiFi is rendered useless.
You didnt mention what carrier you have. I have Cingular and they even state on there website that If you configure the Edge/GRPS to connect, then WiFi may not work.
*The Good news*
I have my 8125 working with both Edge and WiFi. Heres what I did:
1. Open Connnections and click on the 'ADVANCED' tab.
2. Click on 'SELECT NETWORKS'.
3. The top pull down should be set to 'MY ISP' or, if you have named your WiFi connection something different, select it here.
4. Click 'EDIT' under this pull down and set connection to 'AUTO PICK'. 'OK' back to Network Management screen.
5. The bottom pull down should be set to 'MEDIA NE'T.
6. Click on 'EDIT' under this pull down. This is where you will set up EDGE using your carrier's settings.
7. 'OK' your way back out. Your done.
These settings let WiFi try to connect first. If no WiFi is available then EDGE/GPRS is used.
Good Luck!
Thank you! Worked for me, but videos streamed from orb still aren't working
Wierd-Fi
I also have WiFi problems after installing HTC official upgrade
ROM 2.25.11.1 WWE
Date 5/11/06
Radio 02.25.11
Protocol 4.1.13.12
ExtROM 2.25.11.102
Everything is great except after successful connection to home WiFi it disconnects after maybe 5 to 15 seconds ... network becomes "unavailable" .. no error message. This happens even when not connected to CIngular EDGE/GPRS (flight mode ON then, individually enable WiFi ON for what that's worth). When I delete my home network WiFi entry to force a re-recognition and setup, it recognizes the wireless net just fine (again) but same behavior.
All my settings are already set as suggested by ralugniC8125 in this thread. I had not tried any of the other ROMs with added features/hacks/fixes found on this website ... would any of them behave differently, you think? PHone was bought from Cingular .. I have not done any unlock procedure (don't really need to from a service standpoint but will if necessary to make a new ROM work right).
Any thoughts appreciated...
tskelton said:
Everything is great except after successful connection to home WiFi it disconnects after maybe 5 to 15 seconds ... network becomes "unavailable" .. no error message.
Click to expand...
Click to collapse
I have just purchased an unlocked Tilt from eBay. I have been scanning the wiki for days now, along with other sources, and to no avail. I still cannot get my WiFi to work properly. If any one has had this issue and has found a solution, I would love to know it!
ok, here's a suggestion since none of you have mentioned it.
Diable the MAC (Media Access Control) Binding on the router. This should help.
Maybe yall can help me now I have it attempting to connect however it only connects to gprs and it even shows it has a great wifi signal
Still Wifi-less and Woeful
lobotomy said:
Diable the MAC (Media Access Control) Binding on the router. This should help.
Click to expand...
Click to collapse
Thanks for the suggestion. This did not help unfortunately. I should mention that I have tried to access several different types of routers... with and without security, and while they are showing up as being available, they will not stay connected for more than a second or two.
Any other possibilities?
Although the left-hand green led flashes, I'm not sure that WiFi is activating. I haven't been able to see any wireless networks, including my own when I was 2-3 feet from the router and WinCE still says it can't find the device and prompts me to turn it on. Has anyone else had this experience?
losborn said:
Although the left-hand green led flashes, I'm not sure that WiFi is activating. I haven't been able to see any wireless networks, including my own when I was 2-3 feet from the router and WinCE still says it can't find the device and prompts me to turn it on. Has anyone else had this experience?
Click to expand...
Click to collapse
You could try these:
This one just to see any networks around:
http://wififofum.en.softonic.com/ie/33768
and this one that does a few things in the connection process to save you finding where to put in some of the settings:
You need .net framework as well to use this but there's a link on the page for it as well:
http://www.kasuei.com/hitchhiker/
Regarding Win CE? Need more info.
Mike
normally i do so by going to the wireless adapter inside the network adapters control panel item. wish i can shortcut it
I have wifi in the house and it shows it at first as available and then flips to unavailable when in fact it is available since my laptop is wirelessly connected. it just keeps scanning and will connect to unsecured wireless routers around my area but will not connect to mine
Any insight as to how I could permanently have it connect to mine...It keeps saying scannig network and cycles from available to not available
similar activity
I have wifi at the office and at home. We use LEAP at work and I have WEP at home for security. the office wifi works pretty well. At home, I get kicked on and off about every minute or so. I haven't figured this out yet.
mikechannon said:
You could try these:
This one just to see any networks around:
http://wififofum.en.softonic.com/ie/33768
and this one that does a few things in the connection process to save you finding where to put in some of the settings:
You need .net framework as well to use this but there's a link on the page for it as well:
http://www.kasuei.com/hitchhiker/
Regarding Win CE? Need more info.
Mike
Click to expand...
Click to collapse
Mike,
WiFiFofum shows no activity when I run it.
Re: PocketWinC, I got the name wrong previously. More information about it can be found here: http://www.geekzone.co.nz/content.asp?contentid=3086 It makes it a lot easier to find wireless networks and connect to them. (legitimately! I'm not speaking of War Driving.)
When I run it, (I've used it successfully with other PPCs) I get the error message: "Unable to locate adaptor. If it was turned off, please turn it on now."
losborn said:
Mike,
WiFiFofum shows no activity when I run it.
Re: PocketWinC, I got the name wrong previously. More information about it can be found here: http://www.geekzone.co.nz/content.asp?contentid=3086 It makes it a lot easier to find wireless networks and connect to them. (legitimately! I'm not speaking of War Driving.)
When I run it, (I've used it successfully with other PPCs) I get the error message: "Unable to locate adaptor. If it was turned off, please turn it on now."
Click to expand...
Click to collapse
Well I think your right Wifi may be showing green LED but like you say it does not sound like it's activating. Have you tried a hard reset? If taht does not work then sounds as if you have a hardware problem.
That Pocketwinc looks interesting - similar to Hitchhiker by the looks of it.
Mike
8525 (Hermes TyTn)server assigned ip address frozen
Following an abortive attempt to connect to the (secure?) wlan at the local University , I now have an address "fe80::209:2dff:fee" locked into place in the field for "use server-assigned IP address" in the WiFi network adapter settings page. Consequently I can now connect to nothing with WiFI ( which had been working perfectly.) I would like to avoid a hard-reset - not even knowing if that will work. TIA
blane64 said:
I have wifi at the office and at home. We use LEAP at work and I have WEP at home for security. the office wifi works pretty well. At home, I get kicked on and off about every minute or so. I haven't figured this out yet.
Click to expand...
Click to collapse
Hi there!
today I finally understood why I'm having a similar issue like kicking off the network every minute. I managed to remotely restart the wireless router via _re_connecting my TyTN to the wireless network. It works as follows:
1. The WLAN router is working normally.
2. I turn on the WLAN on TyTN and it gets connected to the network. Everything works fine.
3. I press the power button to put TyTN in stand-by mode.
4. I press the power button to turn TyTN on. It tries to reconnect.
5. The router restarts.
At home I have a similar issue with a different router. It seems to restart on reconnection.
Why is this so? Is this a bug in TyTN or in router's firmware? Can it be corrected somehow?
The router is a DLINK DI-824VUP+ with, I guess, the most recent firmware.
The phone is original HTC TyTN with:
ROM 1.18.255.3
Radio 1.03.03.10
Protocol 32.34.7010.01H
ExtROM 1.18.256.9660
Egils
I have an elfin now for almost 2 years. My problem started about a week ago. I tried to turn on wifi to surf the web but wifi just won't play. If I open up comm manager and press on wifi icon, the rotating busy icon comes up and in a few seconds, goes away and wifi icon stays white. If I try turning wifi on from the settings menu nothing happen either. After doing a hard reset, all is fine again and working.
I want to fix the problem without losing all my programs and save myself the hassle of reinstalling everything but nothing I try works.
If anybody has any suggestions, I would appreciate it very much. My phone is still under warranty so flashing is out of the question too.
Something I have noticed is that under the connections tab under settings, the wifi icon is not listed the same but has a new name of Network Cards. All network cards are still listed there.
help me !
I am in the same trouble. After up rom version "a touch of HD", my fone isn't able to use wifi anymore. I failed to make it recover again !
Hi All,
I have just got an iPAQ 5450 and it all works fine apart from WiFi, the problem is that WiFi only works when it's in the cradle and as soon as I take it out the cradle it stops but it still says WiFi is still on??
If anyone could please help I would be most great full, thankyou very much.
Almoace.
unless you confuse connection icon with wifi being connected icon
it sounds like a hardware issue
Connection
If you are connecting via the cradle, you are connected by "USB" not wifi... even if wifi is "on".
When you want to connect via WiFi you will need to set up a completely different setting with your PC and ActiveSync (if you are using Windows). I have found that you sometimes need to delete all prior network connections with any other device before an iPaq cooperates.
The iPaq 5450 is not a phone and the WiFi was designed as a primary source for connecting, as a result they have excellent WiFi radios. You really should not have a problem connecting, just do a little more research and I think you will be fine.
Thanks for your help guys, on wifi setup I do have different profiles so I'll delete them and start again with a new profile and after going into every part of the iPAQ I have found more connection settings that are, Internet Settings, Work Settings & Work and also there is dialing Locations so by the looks of things I will have to restore the setting to default and start again.
If / When I get it working I will report back here so you know I have it working and for any other ppl that may have the same problem as me.
Thanks again guys I'm very greatfull
Xda-viewers,
yesterday i tried to put on my WiFi, but it didn't work anymore
I have my HD2 for about 1month, very happy with the phone,
and this is the first mayor malfunction
When i press WiFi ON in the comm-manager it shows it's loading,
and then nothing, doesn't go ON,
turned the phone off-on, soft reset.. nothing..
anyone else had this glitch?
hard reset or other solution?
It always worked, untill yesterday
If I were you I would go for a full backup with SPB, and then restore (maybe excluding everything regarding the wifi) after a hard reset
I would try doing hard reset.
However, I had the same problem with my old Fujitsu Siemens Pocket Loox N560 and they had to exchange mainboard.
Do you have it charging? I can't seem to connect to any Wifi networks when I have the phone plugged in. Once i disconnect it, it works fine.
If you are connecting it using USB, make sure WMDC / ActiveSync is set to allowing your phone wireless connections while connected to your PC!
???
phone is fully charged
not connected to PC or anything
not working, going to try some things
anyone goto suggestions except hard reset?
else i hard reset tommorow,
thankz
You mean you can't turn ON or NOT CONNECTING?
If its not connecting, did you try to delete the connection settings from advanced wireless settings and try reconnecting again?
skr_xd said:
You mean you can't turn ON or NOT CONNECTING?
If its not connecting, did you try to delete the connection settings from advanced wireless settings and try reconnecting again?
Click to expand...
Click to collapse
It's really not turning ON.
I press the Off-On button, I see it loading and then, nothing,
WiFi is still turned OFF.
timodc said:
It's really not turning ON.
I press the Off-On button, I see it loading and then, nothing,
WiFi is still turned OFF.
Click to expand...
Click to collapse
I've got exactly the same problem - have only noticed it today.
If I go into wireless network config and select my network there and click connect, it takes ages before it says "connected" and then immediately changes to "not connected". I've obviously checked and rechecked my settings. It simply will not connect any more.
i also can't remember installing an update which would cause this probleme..
Connected to PC
When connected to PC, in the comm manager, the WLAN is dissabled, can't even push it, maybe something went wrong with disconnecting and this is the reason why my WiFi is not working - going on?
Anyone?
I'm not at home, so can't do anything with mine at the moment, but out of curiosity, did you use then Wifi N option in BsB Tweaks? That's the only thing Wifi related that I can think of touching recently.
Tried it
Indeed, thought the same,
tried to put Wifi-N off, soft-reset, but no change
Almost at the edge of HARD-reset
timodc said:
Indeed, thought the same,
tried to put Wifi-N off, soft-reset, but no change
Almost at the edge of HARD-reset
Click to expand...
Click to collapse
I really hope it doesn't need a hard reset. I'm not gonna be happy if I have to do that AGAIN!
I'm gonna keep searching, in the hope of finding a solution.
Out of curiosity, do you ever use the Wifi router app?
WM-Wifirouter
I tried to use the Wlan-Router with Comm manager,
didn't work that well,
installed app I had on my P3600: WM-Wifirouter,
this worked like a charm,
Timo
I've solved my problem! Yay!!
I don't know if this will be of any help to you, but give it a try and see how you get on.
Basically, when using the in-built wifi router, it assigned the IP address 192.168.1.1 to the wireless adapter. This is fair enough, for a router, but obviously not for when you want to connect to a wifi network and get assigned an IP address automatically.
I had seen other people suggest that this may be the problem, so I'd already checked my IP settings for the wireless adapter, and they were set to automatic.
However, if you run the wifi router and then go to your IP settings, it says 192.168.1.1. Set it to automatic while the router is running.
This made my phone get a bit upset, and I ended up reseting it, but since then I've been able to connect to my home network again.
So...
1. Run and start the wifi router
2. Go to settings, Connections, Wifi, Wireless networks, Network Adapters (tab)
3. Select the network adapter (Broadcom 802.11 DHD Network Adapter)
4. Change to use a server-assigned IP address, instead of a specific one
5. Click OK
6. Reset the phone - don't close the wifi router app first.
7. When it starts up, go to the comm mananger and disable wifi.
You should now be able to start wifi and connect to your home network. (It may do it automatically if you don't do step 7 - I'm not sure).
Give it a try and let us know how you get on
Sensational johncmolyneux!!!
I had this problem too - it was doing my head in, but now seems like an obvious conflict. Thanks for finding the solution.
Now all I need to do is solve my BT Voice Commander problem (reported in many other threads) and the HD2 will have the same functionality as the Hermes it has replaced ;-)
Cheers,
Lordbowl
You still haven't hard reset?! I am doing hard reset every 6days because of mod/theme and other crap testing
Backups with resco/pim/office2007 entreprise on windows 7 beta do the trick to have phone working in 15 minuts.
johncmolyneux said:
I've solved my problem! Yay!!
I don't know if this will be of any help to you, but give it a try and see how you get on.
Basically, when using the in-built wifi router, it assigned the IP address 192.168.1.1 to the wireless adapter. This is fair enough, for a router, but obviously not for when you want to connect to a wifi network and get assigned an IP address automatically.
I had seen other people suggest that this may be the problem, so I'd already checked my IP settings for the wireless adapter, and they were set to automatic.
However, if you run the wifi router and then go to your IP settings, it says 192.168.1.1. Set it to automatic while the router is running.
This made my phone get a bit upset, and I ended up reseting it, but since then I've been able to connect to my home network again.
So...
1. Run and start the wifi router
2. Go to settings, Connections, Wifi, Wireless networks, Network Adapters (tab)
3. Select the network adapter (Broadcom 802.11 DHD Network Adapter)
4. Change to use a server-assigned IP address, instead of a specific one
5. Click OK
6. Reset the phone - don't close the wifi router app first.
7. When it starts up, go to the comm mananger and disable wifi.
You should now be able to start wifi and connect to your home network. (It may do it automatically if you don't do step 7 - I'm not sure).
Give it a try and let us know how you get on
Click to expand...
Click to collapse
-When I try to connect the WLAN-Router with the Comm Manager, it keeps on loading and nothing happens.
-When I try the WM-Wifi-Router app which I used on my P3600, it says not abble to connect WLAN
-All my settings are server-assigned-IP-address
Still not able to put on my WLAN,
Timo