Database Users

8525 Bluetooth disconnects with headset mid-call

Hi All,
I have been reading a lot of messages on both 8525 and 8125 trying to isolate the issue and there doesn't seem to be a straight asnwer anywhere and hence I am trying to get the attention of the users here...
I have a pioneer navigation system with a bluetooth built-in. My previous phone (blackberry) and my wife's treo650 both stay connected with car's bluetooth when on call (never a disconnect). But my new 8525 gets disconnected mid-call (usually after 2 to 5mins, but have also seen a disconnect within 1min). That is, it does pair with the car kit and when there is no call going on, the bluetooth connection never dies. This disconnect only happens mid-call, almost all the times.
I have the latest ROM (1,34.502...., radio: 1.16), got the phone about 2 weeks ago from Amazon.com. Called cingular and they say could be faulty phone and I have searched other forums like audi message board where their car kits are also having the same disconnect problem with 8525, so I doubt this is a single phone issue.
I have taken the 'band' hack and forced the phone to be in either GSM or WCDMA mode and in either modes, the phone still exhibits the same problem (there might not be any connection between the two at all, bluetooth with GSM/WCDMA, but thought there might be some weird connection...but not the case thankfully).
I read somewhere about some bluetooth tweaks on 8125, but never found what those were. I need some help here otherwise I am going to return the 8525 and stay away from it. I need the bluetooth to work efficiently.
thanks for all your help
Phal
San Jose, CA

please help
I really need some help, clue or direction on solving or at least isolating this bluetooth issue. I love the 8525 but if I cannot fix this bluetooth mid-call disconnect issue, I will unfortunately have to return, which I don't want.
What headsets the 8525 works fine with (no drops mid-call)? May be that is a starting point.
Please also give me some links to 8125 tweaks that some talked about? pof/other moderators/anyone?
thanks a lot in advance!!
Phal

I have an Motorola H700, and every once in a while it will disconnect, looking at the phone after that, BT is turned off, turn it back on and it works again...
There are problems with the hardware and the API used to access it, good phone, but I don't think it was ready for the market yet when they released it. It is likely to be corrected in the next ROM release, last I heard from Cingular is mid 2007, but by the way things go, prolly around late 07/early 08.

I'm having similar issues with the BT headset I use, which is a Samsung WEP150. It'll drop midcall to the handset. I'll look and BT is turned off.
The only remote correllation I've found is that it seems to occur when I've received a new email or something a la ActiveStink.. And I haven't really been able to confirm that... But I have definitely noticed it happening then though.

my 8525 does this as well with my factory BT in my 05 Acura TL. Kind of frustrating, have not been able to figure it out yet.

Problems w/ Audi BT as well
Same issues with my Audi Q7 BT. I have seen posts in this and other forums blaming the MS bluetooth stack.
My 8525 worked flawlessly with my Garmin NUVI 660, never disconnected or failed to connect automatically. This is frustrating.

8525 Fix
I had the same problem with the 8525 and my Pioneer Avic-Z1 bluetooth kit.
I hacked the registry to force the bluetooth radio to stay ON, rather than going into sleep mode. This seems to have fixed the problem (although with limited testing at this point).
My calls would consistently disconnect with 2-4 minutes. After the hack, I've had 2 45-minute+ conversations with no trouble.
Here's the fix... install a registry editor (like PHMedit), and add a DWORD here:
HKLM\System\CurrentControlSet\Control\Power\State\ Suspend
Add a DWORD called btl1: (note the colon, the colon must be there), with a DWORD value of 2.
Good luck!

My Q7 as well i took the advice of wolfgram and did this to my phone i will let you know how it works it would be a shame to give up this phone but it is really useless if this feature does not work right.

Well this is what i did i did what wolfgram said and it still cut out but not as much so i took the checks off in the advance power mode and never let the phone go to sleep and it works all the time. HTC needs to upgrade thier bluetooth setting not to go to sleep. It must stay active at all times MY phone book and all other info posted into my Q7 with no issues at all and it even sees the bluetooth b4 the MMI system in the car Boots up..
Lance

Resolution I think
I turned off 'Making device discoverable to other devices' and it seems to have solved this problem, I am using the phone with a parrot kit and it kept disconnecting now it works all the time.

Treo 750 doesn't have this problem
Well, hopefully you owners of Hermes have figured out the fix. I had to return it and now got the Treo 750 and can gladly say the problem is not there. The treo 750 has the v1.2, but I guess following the replies here, that possibly Palm fixed the problem by keeping the BT radio on at all times.
In any case, here is the post I wrote in avic411.com forum - if you want to see any follow up responses by other owners..
http://avic411.com/forum/viewtopic.php?p=24170
cheers
Phal

Bluetooth cut out
I am having the problem too with the garmin Nuvi and the Tytn - which is ineresting seeing as how one poster had no problem with the Garmin device. Here is something else that is interesting - I did not have the problem when I had the HTC 1.18 Rom installed. After I flashed the HTC 1.35 Rom, the problem began. I have already tried upgrading my firmware on the Nuvi - that did not help. I also use a Nokia 800 bluetooth headset - and that never cuts out with either ROM. I will try turning off the bluetooth discovery first. If that does not work, will try editing the registry. Keep you posted.

Turning off bluetooth discovery did not work.

Turning Off Bluetooth Did Not Work For Me Either

this worked for me.....
http://forum.xda-developers.com/showthread.php?t=247520&page=10

drains the battery quicker, but no more bluetooth problems.....

Hey guys, has anybody found a solution for the auto turning off of the BT in suspend mode? its gettin really annoying

TyTN Bluetooth | Random car disconnect

Hi all,
I know there are plenty of threads about the TyTN bluetooth issues, but my questions differs in two ways which I have yet to come across:
I do NOT have M$ VoiceCommander installed (and don't want to install it)
My bluetooth issue relates to my car's handsfree feature - my TyTN randomly connects and disconnects. Apparently Audis, VWs, BMWs, and Acura's all suffer from this this problem.
The situation:
When I start my car, the phone will successfully merge with my TyTN. Approximately 30 to 60 seconds later, the connection will be lost. Shortly after that the connection will re-establish itself, then it will disconnect itself a short period later. This pattern repeats endlessly.
I've tried each of the following Tweak programs but none have helped.
jetwaremobile
Tweak2k
HTweakC
I've heard that there is some kind of registry tweak that will prevent the bluetooth stack from disconnecting from my car's handsfree feature, but after looking for about 2 days now, I can't find it. Can anyone help?
thanks.
jm

Yep, got exactly the same on my BMW 630....
Can t find any tweak but....
I am a heavy email user (thru BlackBerry connect) and I noticed that
the higher the number of messages stored, the higher disconnections appears.
At the same time, the TyTn is slower and slower....so my idea that this is related to some timeouts somewhere....
For your complete info, the MS bluetooth stack in my previuos S100 have able to.....immobilize my 630 !!!!!!!!! yes, incredible...
The MS stack messed up with the BMW bt ...and this later would stay ON for ever...even after switching car s power off.
This was sucking the car s battery untill the car would start !...
BMW could not reset the BT module unless disconnecting battery....but...then the active steering had to be re adjusted with the proper BMW computer...
This is a real story.

johnmclean said:
Hi all,
I know there are plenty of threads about the TyTN bluetooth issues, but my questions differs in two ways which I have yet to come across:
I do NOT have M$ VoiceCommander installed (and don't want to install it)
My bluetooth issue relates to my car's handsfree feature - my TyTN randomly connects and disconnects. Apparently Audis, VWs, BMWs, and Acura's all suffer from this this problem.
The situation:
When I start my car, the phone will successfully merge with my TyTN. Approximately 30 to 60 seconds later, the connection will be lost. Shortly after that the connection will re-establish itself, then it will disconnect itself a short period later. This pattern repeats endlessly.
I've tried each of the following Tweak programs but none have helped.
jetwaremobile
Tweak2k
HTweakC
I've heard that there is some kind of registry tweak that will prevent the bluetooth stack from disconnecting from my car's handsfree feature, but after looking for about 2 days now, I can't find it. Can anyone help?
thanks.
jm
Click to expand...
Click to collapse
I have the same problem with a CK3100 kit, don't have a solution, but would like one, didn't have this problem with a Jasjar nor Wizard

TyTN bluetooth | random disconnect when using car handsfree - more details
Thanks for the replies so far.
Although the following thread did not help me with my problem, it might help one of you. If you're having problems mostly related to issuing voice commands using M$ VoiceCommander, I think there *might* be a solution in that other thread for you.
Just to reiterate my problem; my TyTN keeps randomly connecting and disconnecting from my car's built-in hands free bluetooth device.
There was a time when if i managed to made a call after first starting the car - before the first random disconnect - the phone would remain connected until the next time I started the car. That no longer appears to be the case.
-jm

I solved the BT problem with my Orange SPV M3100 by setting it to never switch off the display automatically (only switching off the backlight after 20 seconds or so). I also use an in-car charger to power the TyTN. The car is an A6 with RNS-E (BT enabled) and TyTN works fine and never loses the BT connection as long as the display is active.
This is a mid-term solution though and I'm still eagerly waiting for a ROM update that will solve the problem for good.

Has anyone tried a ROM with aku 3.3?

jasonrhcastle said:
Has anyone tried a ROM with aku 3.3?
Click to expand...
Click to collapse
Yes.
And on my CK3100 I now no longer get disconnects. I did have to uninstall jetware as it wasn't reliable. My TyTN now connects perfectly and no longer drops.
One thing I did find is that the TyTN hates it when more than one handsfree device is in its trusted list. Make sure that the ck3100 is the only handsfree device paired.

http://forum.xda-developers.com/showthread.php?t=247520&highlight=bluetooth+keeps+disconnecting

ajax007 said:
I solved the BT problem with my Orange SPV M3100 by setting it to never switch off the display automatically (only switching off the backlight after 20 seconds or so). I also use an in-car charger to power the TyTN. The car is an A6 with RNS-E (BT enabled) and TyTN works fine and never loses the BT connection as long as the display is active.
This is a mid-term solution though and I'm still eagerly waiting for a ROM update that will solve the problem for good.
Click to expand...
Click to collapse
I've tried changing the automatic switch off setting and it made no difference on my SPV M3100 (with Parrot CK3100) - I reckon that the external power is what fixed your problem (this has worked for others too).
Sadly it's not a convenient fix as I like to leave my phone in my pocket when I'm in and out of the car. Orange say there is no 'issue' so there's no sign of a ROM update but HTC know of the problem but I have to wait for Orange to release their ROM update. I can't use the HTC update. If only us Orange users could tell them enough times they might listen now that some AKU 3.3s are being released. Orange technical department won't speak to end users like me - they have actually refused to discuss it with me and just pass messages back and forth from customer relations. Any other ideas?

A solution - thanks to Parrot
Yippee - thanks to Parrot I have got a solution to the TYTN / CK3100 problem (my phone is the Orange SPV M3100).
As Orange and HTC can't find any solution I kept asking Parrot for ideas. Their excellent customer service department tried various settings which made no difference until I was offered a trial of some beta test software called VCF creator. Once you have the VCF from the PC's Outlook you just need to beam it by BT across to the CK3100 and alter some settings (takes 5 minutes maximum). The small sacrifice is that you don't have auto-synchronisation so if your numbers change a lot you will need to do another VCF upload. The extra bonus benefit is that all your numbers will be grouped together. So, for example, you access someones name and then you can see their mobile/home/work number rather than having a separate line in the main list for each phone number. The problem is a result of how Windows Mobile phones provide the data. With this bonus you can then use voice activation to input a name followed by a keyword mobile, home, work etc. Fantastic!

587dan said:
Yippee - thanks to Parrot I have got a solution to the TYTN / CK3100 problem (my phone is the Orange SPV M3100).
As Orange and HTC can't find any solution I kept asking Parrot for ideas. Their excellent customer service department tried various settings which made no difference until I was offered a trial of some beta test software called VCF creator. Once you have the VCF from the PC's Outlook you just need to beam it by BT across to the CK3100 and alter some settings (takes 5 minutes maximum). The small sacrifice is that you don't have auto-synchronisation so if your numbers change a lot you will need to do another VCF upload. The extra bonus benefit is that all your numbers will be grouped together. So, for example, you access someones name and then you can see their mobile/home/work number rather than having a separate line in the main list for each phone number. The problem is a result of how Windows Mobile phones provide the data. With this bonus you can then use voice activation to input a name followed by a keyword mobile, home, work etc. Fantastic!
Click to expand...
Click to collapse
If you use the Jetware BT software you can do the same thing e.g. beam the whole contact list in one go and then set the Parrot to not sync by choosing the Ericsson No Sync profile. This is how I have mine set up, also with the Jetware software it sends over the Service Provider, Battery and Signal strength settings to the Parrot, something which the native stack doesnt do.

Solution for this
Hey all, i have purchased a parrot 3100, the software in it was 1.6, i had the same problems but it's greatly and successfully solved using the new jetware 1.3 . i don't know if i can post some linx here, but here you go, if this is illegal for this site please remove them
http://rapidshare.com/files/30296941/JetWare_1.3.rar
http://www.megaupload.com/?d=PL5UX5KC

How do you stop BT turning off ?????

Hi,
Can't find anything in any other threads so here goes..
My M3100 (TYTN) turns bluetooth off when I turn off my Sony HBH 300 BT earpiece.
It doesn't happen everytime, maybe 50% of the time. It wouldn't be a problem but during the working day I connect and disconnect maybe 10 to 20 times and when I get back on the road and fire up the earpiece I suddenly find no BT.
I'm normally not in a place where I can safely stop to go through the connections screen to re activate it....
Not had this problem with any other phone, Nokia, SE etc...
I think it also happend once or twice after turning off my TomTom One whilst running the traffic BT connection to my phone...
It is getting to be a pain, so much so I'm considering using a OLD Nokia instead of the M3100. Only advantage is the M3100 allows more than one BT connection at the same time although you do have to connect the BT earpiece before connecting to the TT One unit...
Any ideas how I can stop it turning off without ME actually turning it off, never happens anyway, I just leave it on...
HELP !!
Phil-w

I have a similar problem and would love to find an answer before my 30 day return period is up! I haven't been able to find out WHY my BT radio always shuts off, but about half of the time I get in my car the BT is off. This - and the MS Voice Command hack not working with my particular HF - is going to make me return this thing.
BTW, I have Cingular 8500 with stock WM5.

Worked for me
Hey guys. I had a similar problem a while back.
I had installed a comm manager, and my BT was randomly shutting off. After getting some responses, I uninstalled the updated comm manager, everything has been working fine ever since.
I would recommend following the same course of action. If you don't have the original installed, maybe try installing a new one.
I recommend keeping the phone. It's great. There is SOOOO much you can do with it. If you are unlucky and got a lemon, that's a different story.
But I do not think this problem is common... good luck.

Last week I updated my ROM to the latest official AT&T release, and my BT problems *appear* to be solved.

Very poor bluetooth connection

Hi guys,
i recently received my iTech R35 A2DP Bluetooth Headset for my Touch HD which is identical to HTC BH S100 since its only rebranded.
Pairing, controls and everything works fine, but when playing music the connection constantly gets lost for short terms regardless of the distance between the phone and the Headset.
The weird thing about it is, that the headset works perfectly with my friends HD. He even could go away like 10m without any kind of interruption.
I already tried some different settings with HD Tweak but no improvement.
Besides I noticed that overall bluetooth performance with my phone, as it once took about 30 minutes to send a 50MB file, isn't that good.
Thanks for any help!
Update:
I tested the Headset today with two other phones (SE W950i and some Nokia). It worked perfectly so I figure something has to be wrong with my phone. I'll perform a hard reset on the weekend and see if it changes anything. Otherwise I'll have to contact the customer service.
Has anybody here experience with german support. If I had to send the phone in, how does it usually take til u get your phone back?

Well, I just performed the hard reset and it solved the issue. Very strange since I hadn't installed that much programs.

Well, the problem returned and I now figured it out in detail.
There's no correlation with the programs installed.
Once the Bluetooth headset is in the Bluetooth-Device-List as it was connected before the constant lags are there.
If I delete it and re-pair the headset the lags are gone for this one time until the headset got disconnected. Even if I get out of range and return in reach connection is crappy from then on.
Didn't anybody recognize such a strange behaviour too?

I have a similar issue with my Sony Ericsson HBH-IS800 phones.
I thought I'd solved it by re-pairing with the handset, and initially that pairing seemed to last for a while, but now it seems I have to re-pair at least once a day to avoid the stuttering (it's really bad, isn't it?)
Frankly, I'm getting pretty disenchanted with my HD. Every time I discover a tweak which sorts an issue, another issue raises its head. I've lost count of the many hours I've spent trrying to get it to work as it ought to.
Wishing I'd got an iPhone. Okay it's not as good on paper, but at least everything works....

I have to agree the bluetooth is dodgy for me at the best of times in trying to connect to any computer.
Surprisingly, Ive had a good file transfer between my HD and MaxOSX, I can't say the same for Windows XP or Vista where on both accounts it has failed to connect via bluetooth to perform an active sync.

Petee said:
I have a similar issue with my Sony Ericsson HBH-IS800 phones.
I thought I'd solved it by re-pairing with the handset, and initially that pairing seemed to last for a while, but now it seems I have to re-pair at least once a day to avoid the stuttering (it's really bad, isn't it?)
Frankly, I'm getting pretty disenchanted with my HD. Every time I discover a tweak which sorts an issue, another issue raises its head. I've lost count of the many hours I've spent trrying to get it to work as it ought to.
Wishing I'd got an iPhone. Okay it's not as good on paper, but at least everything works....
Click to expand...
Click to collapse
Thanks for your information. At least I'm not the only one with this issue.
Meanwhile I tested this behaviour with my buddies HD and it's the same pattern with his one.
I contacted german support today and will report after their answer.

i've been having the exact same problems with my hd. i would be able to pair it with my landrover, but then the connection would be lost. (there's another thread on this somewhere).
anyway, i tried installing BTRestore and BTRestart along with Mortscript and a custom script to help keep the bluetooth active. however, my problem was not that the bluetooth was turning off, but that the connection would not stay active.
so i installed a custom rom, Dutty's version 1.7, and also installed jetware bluetooth program (www.jetwaremobile.com); so far so good (*fingers crossed*). this is my 3rd day and the bluetooth works great. the phone connects with the car instantly, my phonebook works and i can make and receive calls without losing the connection.
so maybe updating the rom will help you too.

Sorry, it's been a while since HTC answered my questions but since their answer was quite disappointing I had no rush to post it.
Summarized they told me the HTC BH S100 was not compatible with the Touch HD even though I pointed out that it's in compatibility-list of the Diamond and both are running the same Chipset and OS and that it works fine after the first pairing.
As I'm tired of reconfiguring my phone I'll wait some time to flash another ROM. I hope WM 6.5 will be released soon and fix this problem, too.

Bluetooth still doesn't work properly!

My X1 has a very annoying problem with it's Bluetooth. During a call using Bluetooth handsfree the phone will drop the Bluetooth connection, leaving the call connected so annoyingly the caller can hear me cursing the unreliability of my phone. I then have to finish the conversation holding the phone to my ear without the headset.
I called Sony Ericsson, who told me to update the firmware. I did - to R2AA007 - makes no difference. They then said it was a defective phone, so I got a new one sent to me...
...this one has worked great for a month, but yesterday the battery ran almost flat and whilst on a call using handsfree it started playing up again. Now it does it all the time again, even though the phone has been fully recharged and rebooted.
I have been very careful not to change any settings with this second phone, no installs of anything. This is a Vodafone UK phone if it makes any difference. Any idea how I can get this working again? Even without the handsfree connected I can see the display flash 'Bluetooth on' at random intervals indicating that it keeps dropping. Sony Ericsson say that this is not a firmware issue that needs fixing now - what do you guys think?

there are many posts regarding your problem. one thing is for sure,you are not the only one. look here http://forum.xda-developers.com/showthread.php?t=480698 and here http://forum.xda-developers.com/showthread.php?t=471181 here too http://forum.xda-developers.com/showthread.php?t=448703 i have my mbw-150 and my hbh-pv712 connected at all times to my x1 the watch is always connected but my headset disconnects randomly as you mentioned even during a call. there is no problem with your phone it's a software issue.

Thanks for the links. What annoys me is that Sony tell me there is no problem and they won't report the bug to their firmware team because "it's been fixed in R2A". This isn't the case, and it doesn't give me much hope for firmware R3A.

Same problem here
I experienced the same problem. Got my X1 in december 2008. Problems started in mid Januari, about a month of good Bluetooth operations, it started to give problems. During a call the Bluetooth connnection is lost, but the call stays open. Can reconnect Bluetooth again during the call, but after some time (sometimes seconds, sometimes tens of seconds) the connection get lost again.
Was glad when the new firmware arrived in Feb 2009. Download it, and the problem was gone fore about one month. Mid march the problem started again. Downloaded (the same) firmeware version again and the problem was gone again for some time. Last week it reappeared again
My conclusion: the Bluetooth bug wasn't corrected in the latest firmware version. Just reinstallation of a new firmeware version resets the phone and the the problem is gone then for some time.....
Seems that there some kind of an internal timer/counter that corrupts good bluetooth operations. I don't want to reinstall "firmware" every time again because I have to reconfigure my phone then every time, which takes a lot of time.
I hope that Sony finally will correct this most irritation bug!!!!
In the mean time I use a Bluetooth restart programme that "turns on" bluetooth every second. This helps moth of the time.

This works for me
In the Bluetooth-Device-Manager tap and hold the stylus on the headset you want to use until a popup is shown, then select use as headset. This worked for me when i have had some problems with one of my headsets supporting more than the "Handsfree-Profile" .
=> better connection under R1, best connection under R2(using R2 since official release)
Good luck WOODY

Hey Guys,
I think i have the solution for the bluetooth problem. i had my Xperia since 11/2008.
i never had a problem with connection when i used my headset. the problem was with the I-Drive disconnection randomly.
I flashed multiple roms from Itje and Jack with the same problem always.
now for the past 2 weeks i have been using Itje V5.5 with no problems what so ever.
the key is to turn bluetooth off in the comm manager everytime you wanna install new programs. i truly believe that installing software with the bluetooth on disrupt something ???
Hope that helps.

mdshahed said:
the key is to turn bluetooth off in the comm manager everytime you wanna install new programs. i truly believe that installing software with the bluetooth on disrupt something ???
Click to expand...
Click to collapse
Honestly, it make no sense to me....

try it!! it will work ...

@mdshaded
I hope youre kidding, I've had BT problem (BT turns off) since I got this phone last year.
With Itje's WM6.5 RC1 I still have the same problem.

I am not Kidding, I tried all cooked and original roms. I had a pocket PC phone for the past 3 years: Trinity, Kaiser and now the Xperia.
Again my dropped BT Connection were with my Car BT system, never with my Stereo BT headset.
try to hard reset and then install Itje V5.5 and keep your BT off until you are done installing all your programs then turn it on and report back.
Cheers

mdshahed said:
I am not Kidding, I tried all cooked and original roms. I had a pocket PC phone for the past 3 years: Trinity, Kaiser and now the Xperia.
Again my dropped BT Connection were with my Car BT system, never with my Stereo BT headset.
try to hard reset and then install Itje V5.5 and keep your BT off until you are done installing all your programs then turn it on and report back.
Cheers
Click to expand...
Click to collapse
I had tried more phones (Eten M600, Asus P525, Kaiser, X1), and did a lot researchs and only HTC's one (Kaiser, X1, Diamond, TP, HD ...etc) gives such issue. Not on my Asus P525 and M600. And I had tried many A2DP devices (Sony: DS-205, DS225, DS970, DS980, Clip-D Radio, Jarba (forget what model), JVC-BT1 (car system)) and only HTC devices give me issue.
And your suggestion of turn off bluetooth while software installation make no sense as installation only perform files coping + registry registration which I don't see any relationship from BT issue.

Dear Jack,
I know it does'nt make any sense. but i had this problem on other devices and was always corrected with a cooked rom except with the Xperia..
there is nothing to lose.. just try it..
my phone had no single dropped connection for 2 weeks now.
All the Best.

what bluetooth issue, ive been using hbh ds-200 since ive got the xperia (used on buses, around the house and alot of places) works great and has a further distance than p1i but only has an issue of button compatability. i think it could be the the bluetooth device ur using or the lack of software. may be wrong completley but hear me out ive had it rnning for ages with music on or durig a phone call cause i cant be bothered to pull out of its case to avoid scratching the phone (i know its stupid) but like i said it is working, for me atleast

same problem ...
I'm experiencing the same problem:
my X1 periodically drops the connection to my BMW iDrive while I'm speaking. But, when I'm not in the car I'm using a plantronics voyager 855 and never had a problem ! So there seems to be a problem with specific bluetooth devices.
Before the X1 I had a touch diamond and it worked without any problems with the same iDrive.
Thomas

Dear Thomas,
i am glad that you mentioned your problem with the I-Drive. I did not have a single drop in BT Connection for 2 weeks now. I truly believe that installing some software impairs the BT connection with my I-Drive.
Again never had any problems with Headsets.
My I-Drive Version I believe was newer than V.25.
Cheers.