Related
I 'suddenly' am unable to have my JasJar connected to Activesync. I have been successfully connecting the last two weeks and did not cahange anything to the PC's set-up.
I killed my antivirus and have no firewall software running.
I have a direct USB connection to my Laptop (no usb hub).
I have tried both Activesync V4.0 and V4.1.
I have deleted all partnerships to get a fresh start.
I have also tried to delete the PPC in the PC's device manager and connect again (I did notice the PPC was listed under the network adapters only, nothing was listed under the USB section).
Nothing seems to help and I am really desperate since I can not sync anything anymore now.
Any suggestions are more than welcome !
Thansk in advance,
Paul
have you tried another PC ? at least this way you can be sure that everything is ok .
I am travelling and will not have any access to another PC before the WE.... I did try another cable but got not lucky..
It does seem to work on another PC.
Anybody any suggestion as to what else I could try to make it work again?
firewall?, thats my pain on my work lappy, i have to vpn into work and that blocks my JJ, i get connecting but no connected, all i can do is disconnect from work which then opens the activesync ports back up. check 7438 and 5679 on your firewall
After a week with AS 4.0 I suddenly found that the only way I could get it to work was to soft reset the Jas Jar while connected. I'm guessing you've already tried that though...
yer, i forgot to say, i can only sync when my JJ has been off for 10+ seconds, if on i get a uab device error if off i connect no problems, this kinda leads me to think that the usb port is in a different mode when on to when on standby, but the usb hosting of devices appears not to be the reason
Carnivor said:
yer, i forgot to say, i can only sync when my JJ has been off for 10+ seconds, if on i get a uab device error if off i connect no problems, this kinda leads me to think that the usb port is in a different mode when on to when on standby, but the usb hosting of devices appears not to be the reason
Click to expand...
Click to collapse
I have the same problem. Get a kind of "USB not recognized" when the jasjar is on/open".
I close the Jasjar after having taken the USB out of course.
Then, after a while ( You say 10 seconds) it works fine and Activesync starts the job.
I can live with it. No soft reset needed.
Very positive to me is the fact that I can also connect to a USB HUB. So no need to plu it directly in my portable.
After connection I can open my little toy. (Gush how I love this thing)
Huib
Yes I have the same problem I only synk when the jasjar is turned off. Most probably one of the reasons apart from firewall issus is office 2003. They said to me from club-imate support that we need the newest office 2003 with sp1.
Hye, im a new forum user. Ive been using a Dopod 900 for quite sometime now and i love it. However, 2 weeks back, upon connecting it to my pc, an error message showed on my pc screen. It said
"USB DEVICE NOT RECOGNISED
One of the usb device connected to this computer has malfunctioned and windows does not recognize it".
At 1st i thought it was a minor problem so i decided to soft reset it. But after soft resetting it still couldn't connect.
Here's the list of things that i've done.
1. soft reset the device/pc
-connect it via cable to the usb port, still not working
2. uninstall/reinstall activesync 4.5
-not working either
3. hard reset device
-also not working
4. reformat pc (last resort)
-no avail...sigh...
HELP!!! It's driving me crazy!
The usb port seems fine, i can sill charge my device, but i can't connect it to my pc!
PLEASE HELP ME!
Thanks in advance.
the problem is on your PC and not on your Device. I didn't get whether you have formated your PC or you planning to??
I don't think it's my pc.
Went to a pda shop, asked the person in charge to have a look at it and he too was confused. He got the same error as i did on his pc.
He reset my device to bootloader mode and plugged in the usb cable. Something like 'usb cable' showed on my device screen. He said that the port was fine so it had to be some other problem which of course he doesn't even know.
Btw, i DID format my pc before going to the pda shop. Still nothing...Thanx for replying and being so helpfull...Hope u can help some more!
Have you tried a diff USB cable
Yup! Tried a couple of different usb cables...still no luck...
Additional info-
I found out that syncing could also be done via bluetooth from a friend, so i gave it a try but, also no go...my device is not recognised...***sigh***
Yes, still no luck...Ive tried a couple actually...
Was this problem solved?
I have the exact same problem. I got it to sync one time though when I disabled my firewall. But that's it.
I can't sync again.
Please, anybody who had had this problem, please share the solution.
Thanks a lot!
maxmiller said:
Was this problem solved?
I have the exact same problem. I got it to sync one time though when I disabled my firewall. But that's it.
I can't sync again.
Please, anybody who had had this problem, please share the solution.
Thanks a lot!
Click to expand...
Click to collapse
Have check this?
Goto your device -->settings-->connection-->USB to PC and check or uncheck advanced network functionality
That's strange. i don't have the USB to PC option on my Connections menu.
I've been suspecting my USB port to be the problem.
Could anyone please take a very clear picture of the USB port in their Uni so I can compare mine.
Thanks a lot.
Nope...it was never solved. I ended up selling my dopod. I was so frustrated. *sigh*
maxmiller said:
That's strange. i don't have the USB to PC option on my Connections menu.
I've been suspecting my USB port to be the problem.
Could anyone please take a very clear picture of the USB port in their Uni so I can compare mine.
Thanks a lot.
Click to expand...
Click to collapse
What ROM ARE YOU USING?
Hi all..
I'm having a problem with the activesync on my phone.
When i plug in the phone to the usb cable on the comp,(winXp pro) It makes the connecting device sound, tries to connect to phone, but dosen't do anythin else. When i try to start activesync on the phone, it loads for a split second then shuts off..
can i reinstall AS on my phone? i've tried re-installing AS on the comp, but still the same problem.
I have done all the usual tricks(check/uncheck boxes)..
I don't really want to do a hard reset as i like the way my phone is at the moment..
Any help appreciated.
thanks.
hi guys,
i have searched the forums for wm 6.5 ROM, but lots of them are still in beta phase,have bugs or slow.
can anyone give link to a stable WM 6.5 ROM for my xda orbit
Thanks in advance
...
6.5
Babbelut ROM WM6.5-28005 v0.3 NLD/WWE
*spb mobile shell is great, he is currently developing beta rom
http://www.sendspace.com/file/97d3p7 (download link for v.3)
http://www.megaupload.com/?d=ZTXWO4D7 (download link for v.Beta)
Downloading it now, will check it later on. THX
Was about to create topic but found this and hopefully will try this and hope it works on my XDA Orbit 2. I brought it off Cex from Aylesbury and it needs some love and update as i have Windows Mobile 6.1 (eeurrgh) and brought it off cos i thought i can upgrade to Winodws Mobile so i hope these works well for me.
Any introductions of doing that?
Thanks in advance.
First link didnt work. The XDA tried to block it by restarting it themselves. Tried third time. And unlucky.
Second Link. How can i use NBH file for my XDA?
...
Wrong place dude..
this is for xda orbit 1/artemis..
your looking for xda orbit 2/ poloris..
you need to be here..
Rn
Hi all I'm new here. My phone "O2 XDA Orbit" behaving strangely. Suddenly the sound disappeared and I can not hear phone calls directly into the phone, and any other person hears me not(microphone off), and not just one click sound on the screen. If I restart the phone with USB cable inserted into the phone and computer (on), then the sound occurs again(but not in original style, sound occur in to the back speaker not in front ), and phone function almost normally with microphone (on)>>> until the next reboot when sound disappear again and microphone is off. I mention that;.... connection the phone to the computer can not be achieved in any of this cases. The error code (USB connection) connection on my computer is {Code 10(One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it)} who can not recognize the new hardware. In your opinion of specialists in this field what would be done? I think something happens to the ROM which gives errors of hardware power. The sound occurs when I insert into the phone power charger connector and disappears when the power supply plug out ... Please if you can help me with some guidance what I have to do one upgrade of ROM or something? Specification of the phone is:
[*]IPL-3.04.0001
[*]SPL - 3.04.000
[*]OS - 3.4.0.0
[*]CPU - OMAP850
[*]Speed 201Mhz
[*]RAM 64Mb
[*]Flash 128Mb
[*]Data bus 16bits
[*]ROM 3.4.206.2WWE
[*]ROM date 4/18/07
[*]RADIO Vers. 02.67.90
[*]PROTOCOL Vers. 4.1.13.28
[*]EXT. ROM.Vers 3.4.206.101
[*]MODEL of phone -ARTE200
[*]Platform - PocketPC
Funny ...!!! Today I put the phone to the charger and after I removed the plug from the power supply, the sound has returned, but the USB connection to a PC still can not set ...! What should I do? A new version of Windows can install on my phone; without connecting the USB cable to the phone(ex.-of my card micro SD)??
Adryum said:
Funny ...!!! Today I put the phone to the charger and after I removed the plug from the power supply, the sound has returned, but the USB connection to a PC still can not set ...! What should I do? A new version of Windows can install on my phone; without connecting the USB cable to the phone(ex.-of my card micro SD)??
Click to expand...
Click to collapse
have you got activesync or windows mobile device centre installed on the pc?
if yes..
i suggest you buy a new usb cable.
i have this problem with a couple of cables.
"USB DEVICE NOT RECOGNISED"
but when i change to a differant cable, everything is ok.
flashing via micro sd - upgrading windows.
have you done uspl 1.11.cmon?
Thanks for your attention Raving in the first place ...! Data cable has no damage that I checked the same cable with my photo camera and it works normally with PC and I have two more data cables and the problem is the same. It seems weird that the phone do some work once, ...once not. It starts when he wants the sound, and can not find any explanation ... In contrast with the USB connection can not establish anything, something happens to the sound module and USB ...PC see's something, but it's not sure what it is, and says he can not establish connection with the new hardware and it gives me error "CODE 10". in Universal Serial Bus Controller and the Active Sync is instaled on my PC but he don't say a word about this connection...I don't know on what to do...! I must mention that this oddity occurred only three days go and without them I do something wrong ... He grabbed him crazy after a normal operation for a year and a half, because we had no problems with it until now ... I used as a GPS and the phone and I was really pleased with him. By the way, what they mean uspl 1.11.cmon? All data of my phone are in the first post.The phone it was once unlocked by someone else, and now I can use any SIM card from any GSM provider..............I forgot to say that I've rebooted 2 times in general mode and now works but without USB connection sound when he wants it or not................But I think she has lost some registry ...!!!
click 1.11.cmon in my signature.
this will divert you to a tutorial thread.
when you can connect your device to your pc successfully, you should do the uspl 1.11.cmon but not for now. do not try and flash a rom yet either, you will break your device. (thats what uspl 1.11.cmon is for)
id like you to just try the "hard reset".
back up all your data first.
bookmark the page as ill be updating it regularly.
personaly i think its your usb cable, eg:
one of my cables works with a micro sd reader but not my for my device, i understand your cable worked but now does not.. however thats what happened to me.
Sound engages when he wants and where he wants. If I restart the phone, sound disappears and microphone stop; and I can not talking on the phone. Enter data cable from PC to phone, and give the phone restart. Once the phone is starts, sound appear but only in back. When talking on the phone sound very loud and sounds of the touchscreen controls can not disconnect the rear speaker who remains engaged and does not want to disengage it from the normal operating mode. Another job here would be that when inserted in the charger cable, the sound is right: each speaker and microphone or operational. If I remove the plug (charger) of phone then the phone function normally just like before, but without USB connection. If I plug "USB cable data" on the phone, to the desktop I see message "One of the USB devices attached to this computer has malfunctioned, and Windows does Not Recognize it. USB Device not recognized." If I unplug USB cable from phone the sound disappears, and what I have to do is to start over again.......!!!!!!!!!
I tested all data cables, and are ok. The problem is hard. The hardware has a technical failure which somehow blocks the data on USB. Battery power consumption is higher and the battery is discharged rather quickly than it was before the cage. At night when I charge the battery full, morning at 10:00 is only 30/40% of capacity. But what is even stranger is that: when I connect phone to PC, in device manager shows me the new hardware (Mobile Device) but after a few seconds there appear a connection error code (CODE 10) that is the hardware can not start. Active sync has not started when the fault occurred..... In your opinion what should be done in this case? ... Should contact a service or ... in any way I can test something before others get the screwdriver into my phone?
sabih00 said:
hi guys,
i have searched the forums for wm 6.5 ROM, but lots of them are still in beta phase,have bugs or slow.
can anyone give link to a stable WM 6.5 ROM for my xda orbit
Thanks in advance
Click to expand...
Click to collapse
Thanks, i will test...
The connection was made the first attempt. After a week of "digging" through all possible places I noticed that the connection was obstructed by the firewall.PFFFFFFFF ..... Finally found! The FIRE WALL(on PC) settings to be set: ADD PORT------ "Outbound UDP ----5679" -on exceptions tab....See this:http://www.microsoft.com/windowsphone/en-us/howto/wp6/sync/activesync-troubleshooting.aspx?WT.mc_id=FWLink
TKX Raving U're the best...
...
Adryum said:
PFFFFFFFF .....FIRE WALL
Click to expand...
Click to collapse
lol, i didnt think about the fire wall being the problem.. typical that it was something that simple.lol although it did sound like a dodgy usb cable..
thats something ill remember
have a good new year dude!
guys i am having a problem....whenever i try to install any ROM i get error 224 device not responding......my htc is connected through activesync.....what can be the issue...i am using windows 7.
..
raving_nanza said:
ERROR [224] : DEVICE NOT RESPONDING
check the ActiveSync connection and run RUU again. if problem continues, uninstall active sync and re-install.
Click to expand...
Click to collapse
1. unplug device
2. re-connect device to pc
3. wait for active sync/wmdc to connect
4. run ruu
5. if error continues unplug device
6. uninstall active sync/wmdc
7. re-install active sync/wmdc
8. restart pc
9. go to step 1.
Rn
quertz?
Hi raving nanza,
you did a great work with BAB v03.
It works great. sometime the touchpanel reacts slow but good.
But i can't change my touch keyboard from qwerty into qwertz.
HKEY_LOKAL_MACHINE\System\CurrentControlSet\Control\Keyboard Layout\"Active" is "00000407"
Thats the German code - but still having Qwerty?
HKEY_LOKAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\"TaskManVKey" is "0x23"
HKEY_CURRENT_USER\keyboard layout\Preload\1\"default" is "000000407"
What to do?
...
che.bike said:
Hi raving nanza,
you did a great work with BAB v03.
It works great. sometime the touchpanel reacts slow but good.
Click to expand...
Click to collapse
thats Babbeluts rom, not mine!
i merely suggest it to the other users
ill look into your qwerty to qwertz keyboard, when i find out ill post it here and ill update the tips&tricks thread
Rn
hello everyone !
i was looking for thread about my problem, i saw some similar problems, solved but not working for me..
i was connected to my PC through USB cable, transfering data few times, about 5 times, than i tried to connect to transfer some more data and nothing, on my tattoo there is just sign of charging and nothing else, no asking for type of connection, there is sound on my PC (connected something through USB ) and nothing else.. i tried to manually set for storage device, put to ask me each time when i connect via USB and still nothing.. also, tried USB DEBUGGING, it says that htc is connected to PC but PC is like dead..
i'm on windows 7 if that means something, thank you for you help
pls anything ?? i have pics to transfer to PC and mp3 for tattoo but i just can't solve this out :S
I had the same problem when I just got my first android. My first guess is - you accidentally killed PC Synchronization process on your phone. Reboot should help (at least it did for me).
I had the same problem and solved it!
put pc sync into taskiller ignore list...
how can you explain me please?
goran95 said:
how can you explain me please?
Click to expand...
Click to collapse
hi
also still have this problem the sync does not happen automatically so what i do is after connecting my phone via USB i go to the USB to pc on my Phone and click on the HTC sync and then the sync happens and i can do any kinda data sync needed try doing it it work for me
USB Debugging also has to be cheked OK
i also have a Wmo Jade this does not happen it sync imm but on the tattoo it always happens and i need to do the above to get the sync working