battery charging question - XPERIA X1 General

how do you tell if your phone is fully charged when charging the x1 beside looking at the battery status when the phone is on. does the illumination light go out when your unit is charged or does it continue blinking whether its fully charged or not.
when i charge mine, the lights blink and then after several hours, i would not see it blink for a little while but then every now and then, i would see it blinking again.
just want to know if the lights stops blinking, the phone is fully charged.

Exactly what I want to know.

Yes, the side lights stop blinking when it is fully charged.

When it stops charging, the lights go out. But then, when in trickle charging mode, it is shown by the light.

how can I see the remaining battery (percentage) without pressing a series of buttons?

bugmeyes said:
how can I see the remaining battery (percentage) without pressing a series of buttons?
Click to expand...
Click to collapse
You can set the clock in the menubar to show the battery power, but the the clock is gone or you use a small and nice freeware like batti: http://code.google.com/p/batti/

on8a said:
When it stops charging, the lights go out. But then, when in trickle charging mode, it is shown by the light.
Click to expand...
Click to collapse
thanks, that makes a lot of sense now that you pointed it out.

Related

No more AMBER after full recharge!!

I have read alot about people complaining about the AMBER LED being still on despite the full charge for even over a night!
I don't know if anyone tried this but I did and it worked. Keep the device on while charging -disable the power management- and sure you will have the AMBER for few hours til it reaches 100% when you shall get the GREEN LED. In my case I use a special screen saver that slide-show a set of pix during the recharge period.
The question now is; would the screen get damaged after sometime having it on for periods like 8hrs? I mean does it lose brightness or quality after a while?
Pls advise.
Personally I use spb pocket plus which clearly displays the charge % on screen so I don't even look at the colour of the light.
:wink:
opposite problem
this is crazy but i get the oppositie thing. My main battery is supposed to be 100% charged so it's supposed to be charging the backup batter. What it does after a while is switching on from the orange light to the green light - although it hasn't finished charging. Once I disconnet the cable and connect it again then it become orange again and probably starts to charge for once again? what's wrong with it?
y

Charging problem ..

(Bare with me, this IS wm6 related)
Okay, so i got this qtek 9090 from a trade online, and the owner pointed out that he had used it for some time now and it worked without problems.
However that seems not to be my experience. At first I was a little worried that it did not came with a charger.. Only a USB cable. No worries i thought, I will just charge it through USB. Now I have had some experiences where phones wouldn't charge from some of my computers, apparently because of some boards that put out lower amps than others. However I knew atleast one computer should have no problem charge ordinary cell phones.
So i plugged it in, and to my worries the battery kept going down... Untill the phone was dried from power and everything got lost again.. and again.. and again.. It seemed a little odd that it apparently deleted everything each time, since the backup battery indicated 100%.
So at last it went into flightmode and I shut it down with the powerbutton and let it be connected.. The first many hours nothing happened.. But suddenly, when i did an occasional check, it said 3% battery. I went to sleep and the next morning it was fully charged. I used it all day in school and it held its power real fine.
Now I got the feeling that this probably was caused by the low amp output from the computer, making it unable of charging to the extend where the phone would still be able of running whilst charging. So i figured i would order a 220v (the powercurrent here in Denmark) -> 5v USB that outputs 700mA, to make a quicker charge.
Well, to day I was gonna receive that adapter, and since I'd read that the wm6 apparently draines the battery some bit, I waited untill today to upgrade to wm6.
I upgraded and everything truely runs quick and stable. But when i recieved the adapter and plugged it in, i was horrified. The power kept going down, as I had experienced when it was plugged into USB.
Now my girlfriend really wanted to play bejeweled on this thing, so she did and then shortly afterwards we took a few hours nap. I had her plug it in the new adapter to charge it. When i woke up i saw the screen blinking.
I could se it was rebooting over and over again, as it had done the first time it completely lost power..
Now besides that extremely annoying charging problem, I now had another concern....
The boot screen shows NONE next to the R and the G.
Next to the D is the wm version displayed.
Any help would be greatly appreciated.
red LED?
Hm.. By doing a hard reset it shows numbers next to R and G again.
It continuely reboots, display boot screen, shuts down, LED is red, reboots, displays boot screen, shuts down, LED is red again and again.
If i hard reset it some times it will at one point stay off, but the LED still lights red.
And now I question wether 700mA is even enough for charging the BA?
1. Higher power given by power supply does not mean, you will get faster charging
2. If you use WM5/WM6 and have Bluetooth turned on, device turns on every few minutes (bug/feature of the driver needed to keep Bluetooth running: look for BigMike's fix for more information). If your deivce is set up to turn off after long time (for ex. 5 mins), battery might drain out in half a day.
3. Check power settings (delays for device power down etc.)
4. In WM6 be sure, that audio manager is not running (prevents device from deep sleep, allows only screen shutdown)
5. If battery shows up 100% and after disconnecting device discharges in less than 2h being turned on all the time (wifi, bt, phone, screen all the time turned on) it means, that battery might be worn. Consider exchange.
R and G showing NONE is normal in WM5/WM6 because of bug (unfixable for now) in the device and it's incomatibility with this OS: after turning on from power down (taking battery out or total discharging) make soft reset just when R NONE G NONE shows up on the screen. Everything will be normal.
jakubd said:
1. Higher power given by power supply does not mean, you will get faster charging
2. If you use WM5/WM6 and have Bluetooth turned on, device turns on every few minutes (bug/feature of the driver needed to keep Bluetooth running: look for BigMike's fix for more information). If your deivce is set up to turn off after long time (for ex. 5 mins), battery might drain out in half a day.
3. Check power settings (delays for device power down etc.)
4. In WM6 be sure, that audio manager is not running (prevents device from deep sleep, allows only screen shutdown)
5. If battery shows up 100% and after disconnecting device discharges in less than 2h being turned on all the time (wifi, bt, phone, screen all the time turned on) it means, that battery might be worn. Consider exchange.
R and G showing NONE is normal in WM5/WM6 because of bug (unfixable for now) in the device and it's incomatibility with this OS: after turning on from power down (taking battery out or total discharging) make soft reset just when R NONE G NONE shows up on the screen. Everything will be normal.
Click to expand...
Click to collapse
AFAIK the lower the mA output, the slower the charge period.
I have had wifi, bluetooth, beam off. I've set shutdown to 2 minutes. I've set it to low brightness and etc.
As i mentioned it had no problems going a whole day of usage in school.
Didn't know about the bug in wm6 that makes only the screen shut off, but at the momemt i can't even boot the device, apparently because it has no batterypower. And having it connected to the charger makes no real difference (other than it will display the bootscreen and perhaps even the Windows Mobile welcome screen thing, for a few seconds.. then go dead again.)
I've had it in the charger for about an hour or two, still not enough power to boot it up.
It feels like it's just not charging sometimes.. And other times it will charge just fine.
Found out about the reset to solve the NONE issue, but i still don't know what it means that its LED is red all the time?
Even 500mA is enough for sure, as charging from USB works fine.
Device will shut down soon after turning on if there is not enough power in battery, even it if is charging. Leave it charging (amber led on the right) for some time. RED led means low battery and no charging (AFAIR).
jakubd said:
Even 500mA is enough for sure, as charging from USB works fine.
Device will shut down soon after turning on if there is not enough power in battery, even it if is charging. Leave it charging (amber led on the right) for some time. RED led means low battery and no charging (AFAIR).
Click to expand...
Click to collapse
Hmm, i see. I just don't understand why it's not charging then :/
trylleklovn said:
Didn't know about the bug in wm6 that makes only the screen shut off
Click to expand...
Click to collapse
This is not a bug - thanks to this you can still listen to your music keeping device with screen turned off, when you don't need it to spare battery.
trylleklovn said:
Found out about the reset to solve the NONE issue, but i still don't know what it means that its LED is red all the time?
Click to expand...
Click to collapse
Red LED (right one) means low battery, no charging. To charge this led must be amber. Details - you must look for manual.
jakubd said:
This is not a bug - thanks to this you can still listen to your music keeping device with screen turned off, when you don't need it to spare battery.
Red LED (right one) means low battery, no charging. To charge this led must be amber. Details - you must look for manual.
Click to expand...
Click to collapse
Okay.
It's odd still. When i connect the charger the right LED starts to light red.
If it means that its not charging, there must be something wrong, since it only happens when connecting the charger..
it can be amber or red. Those are different colors and meaning.
You can confirm it charges touching the battery - it becomes slightly warm after some time.
jakubd said:
it can be amber or red. Those are different colors and meaning.
You can confirm it charges touching the battery - it becomes slightly warm after some time.
Click to expand...
Click to collapse
I KNOW that, but it is not going amber. It stays red all the time.
Found this thread that discusses a similar problem; http://forum.xda-developers.com/archive/index.php/t-233782.html
Apparently it shows RED light all the time if the battery is dead.. However i hardly doubt that the battery, which could power the phone just fine for and entire day, should be dead.
However, one suggestion in the thread was to take out the battery for some time and then try again. So I will do that for now.
Behavior has changed a bit now..
The LED is still red when i connect the charger. However, if i try to turn it on following happens:
Boot Screen shows for a couple of seconds...
Windows Mobile startup screen appears and the LED changes to orange/amber..
After a few seconds the screen turns black and the LED changes to red again...
And then after a few more seconds the boot screen appears again and everything is repeated, over and over.
If I disconnect the charger the boot screen appears, the wm startup screen appears, this time with a flashing red LED.. shortly after the phone turns off.
trylleklovn said:
Behavior has changed a bit now..
The LED is still red when i connect the charger. However, if i try to turn it on following happens:
Boot Screen shows for a couple of seconds...
Windows Mobile startup screen appears and the LED changes to orange/amber..
After a few seconds the screen turns black and the LED changes to red again...
And then after a few more seconds the boot screen appears again and everything is repeated, over and over.
If I disconnect the charger the boot screen appears, the wm startup screen appears, this time with a flashing red LED.. shortly after the phone turns off.
Click to expand...
Click to collapse
I've seen this problem before. The charger is not putting out enough power to both charge and boot the BA. So what happens is that it starts charging enough to start boot, but as soon as it has enough power to start the boot, it immediately drains it by starting to boot with screen at full brightness.
What I do in this case is to try to catch it just as it starts to boot and turn the backlight off by holding down the power button for 5 sec. This turns off the backlight so there is less drain and the thing can boot up and start charging.
All in all, its a pretty stupid bug but what the hell, there is a solution to it.
Good luck.
motisu said:
I've seen this problem before. The charger is not putting out enough power to both charge and boot the BA. So what happens is that it starts charging enough to start boot, but as soon as it has enough power to start the boot, it immediately drains it by starting to boot with screen at full brightness.
What I do in this case is to try to catch it just as it starts to boot and turn the backlight off by holding down the power button for 5 sec. This turns off the backlight so there is less drain and the thing can boot up and start charging.
All in all, its a pretty stupid bug but what the hell, there is a solution to it.
Good luck.
Click to expand...
Click to collapse
This seems to work atm. (just a few seconds since it successfully booted)..
Does this mean that the device really cant charge if its not "on" ?
(I can see its booted and the LED is now orange. If only it will stay this way untill it has been recharged further ))
trylleklovn said:
This seems to work atm. (just a few seconds since it successfully booted)..
Does this mean that the device really cant charge if its not "on" ?
(I can see its booted and the LED is now orange. If only it will stay this way untill it has been recharged further ))
Click to expand...
Click to collapse
It can charge when it is off. BUT... When its off, its not really off... It has to finish booting and then you can turn it off. Then it will charge faster as it only has minimum drain on the battery. As I said before, its a stupid design.
motisu said:
It can charge when it is off. BUT... When its off, its not really off... It has to finish booting and then you can turn it off. Then it will charge faster as it only has minimum drain on the battery. As I said before, its a stupid design.
Click to expand...
Click to collapse
Well we can certainly agree on that
So does the phone also basicly use to much power to be used and charged at the same time? Which would explain why it seemed to lose power even though it was connected to the charger.
Although it still doesn't add up for me, as at one point i was playing a game on it, while charging and then it charged real fast, where you would expect it to use more power
Oh well, if only it keeps charging now i'll be glad
trylleklovn said:
Well we can certainly agree on that
So does the phone also basicly use to much power to be used and charged at the same time? Which would explain why it seemed to lose power even though it was connected to the charger.
Although it still doesn't add up for me, as at one point i was playing a game on it, while charging and then it charged real fast, where you would expect it to use more power
Oh well, if only it keeps charging now i'll be glad
Click to expand...
Click to collapse
I have found that if you only use the USB cable to charge, it takes much longer (if at all) to charge if it is on. Thats why I bought cradles that have external power suppies as well as the USB sync cable. With this configuration, it gets to full charge in about 90 minutes.
Hm.. yeah.. I let it charge for some time, until it shut down and the LED changed to red again.. The same thing has happened about 3 times now.. If I try to navigate it with the brightness off it will shut down after a few clicks..
Seems like either the battery is completely dead or it's simply not charging.. :/
Think i have to buy a new battery and a cradle, although i didn't really want to spend money on this phone as i got it virtually for free (through a trade of a w810i)
trylleklovn said:
Hm.. yeah.. I let it charge for some time, until it shut down and the LED changed to red again.. The same thing has happened about 3 times now.. If I try to navigate it with the brightness off it will shut down after a few clicks..
Seems like either the battery is completely dead or it's simply not charging.. :/
Think i have to buy a new battery and a cradle, although i didn't really want to spend money on this phone as i got it virtually for free (through a trade of a w810i)
Click to expand...
Click to collapse
Get it to orange and then push the power button (short push) to turn it off (not long push which only turns off the backlight). Then let it charge for an hour or 2 (or even all night). By then, it should work OK.
motisu said:
Get it to orange and then push the power button (short push) to turn it off (not long push which only turns off the backlight). Then let it charge for an hour or 2 (or even all night). By then, it should work OK.
Click to expand...
Click to collapse
Yeah, i tried that. As soon as i press the power button it goes to red again.
Update..
A litte update (i might as well document everything I find out here, if anyone should run into a similar problem).
Now, I've had the device connected to the charge for some time now.
What happens is that the device boots up, automaticly dimms down to no light (since i once had hold down the power button, to dimm down light).
Then it boots up, and i can see everything running.
I can navigate to the battery status menu, which shows
Battery: 0% (charging)
Backup battery: 25%
After a few minutes the device shuts down, and the LED goes red again. But after about a half a minute it will try to boot up again, and it goes through everything again.
What I've noticed is that the backup battery slowly increases, and while im writing it has gone all the way to 75%. The good thing about this completely automatic procedure is that it apparently slowly charges, at least, the backup battery.
My theory is that the backup battery has first priority in the system, so that the regular battery wont charge untill the backup battery is up. And since the backup battery can't apparently be used for actualy powering the system, the system will continuesly reboot because of lack of power, theoreticly untill the backup battery reaches 100% and it starts to charge the regular battery.
The whole problem seems to be cause by some charging malfunction, so that both batteries has been completely discharged. I hope that by letting it continue to reboot, charge, reboot, charge, etc. it will revive the battery.
I will return with more info tomorrow.
Any suggestions are still greatly appreciated.

Intermittent ReCharge Light

Has anyone else noticed when you plug in the Phone to be recharged, occasionally the 'red' indicator does not come on or disappears?
It's now happened to me several times ~ I plug the Phone in for a recharge, initially the red light comes on then after a few seconds it goes out leaving no indication if it's charging or when it's complete.
Beards
Read this that i posted several days ago and check your charger
http://forum.xda-developers.com/showthread.php?t=446583&highlight=power+supply
"Wiggle" the charger around and see if the charge light goes on and off!
Beards said:
Has anyone else noticed when you plug in the Phone to be recharged, occasionally the 'red' indicator does not come on or disappears?
It's now happened to me several times ~ I plug the Phone in for a recharge, initially the red light comes on then after a few seconds it goes out leaving no indication if it's charging or when it's complete.
Beards
Click to expand...
Click to collapse
Could it due to bad physical connection?
No guys.
I'Ve cheched all connections.
Besides, if I leave it plugged in whilst there is no light showing and switch off the Phone the red charging light then comes on.
Beards
Well this is now really starting to bug me.
I've carried out a Hard Reset thinking something was interferring with the charge light procedure but even on a default machine with the device running the red light simply does not come on.
Swith the Phone off, then connect and the red light appears.
So.... when my machine is running I don't get the indicator (but it is charging I know because after leaving it for 30mins I've checked and sure enough it's charging).
Any other ideas???
My Trinity does this when overheating, it stops charging and blinks the LED. Unplug for 10 minutes and replug.
tnyynt said:
My Trinity does this when overheating, it stops charging and blinks the LED. Unplug for 10 minutes and replug.
Click to expand...
Click to collapse
Now that's an answer I was not expecting...... Thanks tnyynt, I'll give that a go on my next charge cycle.
Edited:
No... that didn't work.... but thanks all the same.
I have now resigned myself to the fact if I want to see the red charging light the only way is to first power down the Phone, then connect to the mains electric and then the red charge light comes on.
If I want I can then switch the Phone back on again whilst charging until the green charged light shows.
Beards

The charging LED turns green when it's full right?

My battery says 100%, then I turned it off and plugged it back in and the indicator was still white. Huh?
patass said:
My battery says 100%, then I turned it off and plugged it back in and the indicator was still white. Huh?
Click to expand...
Click to collapse
The anorexic manual says Green is 95% or higher. Maybe the indicator had a margin of error or somehow used up 5% of its power cycling (which would be unfortunate)?
StarlessKnight said:
The anorexic manual says Green is 95% or higher. Maybe the indicator had a margin of error or somehow used up 5% of its power cycling (which would be unfortunate)?
Click to expand...
Click to collapse
I'm not sure of the level that Motorola uses, but with Cyanogenmod 7 on my Droid Incredible the charging light turns green at 90%. Maybe this is a standard Android value???
I seem to be flying through my battery, but I HAVE been doing a ton of stuff. Even playing games via bluetooth and hdmi on my big tv... I'll leave it off and plugged in for an hour and thirty minutes and see if the indicator changes color. Still white at the moment.
EDIT - At full, 100% charge (tells me so when it's on), my LED is White. Someone please verify their LED colors for me...
During charge mine is white/blue. When it reaches 95ish percent it turns green.
Regardless of when the charge indicator turns white, green, etc like many other mobile devices the battery gauge may not be all that accurate. When the battery gets to a certain point, charging stops and discharging begins again. After a discharging for a while, charging may begin again. The amount of charge shown may depend on where you catch it in the cycle. Unplugging it after it becomes green and then plugging it in again causes a "bump charge". This is fairly common behavior and hardly exclusive to the xoom.
If you want to really know what is going on, I suggest using this free android utility / widget...
[UTIL] current widget - shows actual current output of a charger
http://forum.xda-developers.com/showthread.php?t=776085
is yours the 3g or wifi xoom?
I've now found that I'm getting between 10-12 hours of heavy usage, probably. I was playing games and surfing and playing music for 6 hours last night and I wound up at 50%. So I guess I can ignore the LED thing, I guess. It turns red when the inner camera is on.

[Q] Led Status Indicator

I just got the Huawei IDEOS X5. Once the battery ran low, I plugged it to the charger. The problem is that the Led Status Indicator (above the screen on the front of the phone) doesn't become orange (it is green). According to the instructions this Led should be orange while the charge is in progress, and become green once the phone is fully charged. This behavior does not follow the info described in the manual of the phone.
Has anyone had the same problem? Do you know why this is happening? Should I return the phone back to the seller?
Thanks
khtc
Led burns green, when the battery is above 90% or so. Under that should be orange. Sometimes when you plug in the charger, it takes time even to start charging (Led is green then). I'd say try to observe more
I thought the same when I first start charging my device, but when the device was fully charged I realized that the led(which seems to me green) wasn't.
The orange color of the led it's not so orange(like was on other devices) but is more close to green(again the green on other devices). On ideos the the green led it's not so light and yellowish, it's more deep like trees green.
And what sanpsa says happens also after 90%
Thank you guys. You were 100% right both!
Dunno, whether it depends of soft or not, but when battery below 15% (or 10%) LED should be red. For mine device it's so.
DTSpawn said:
Dunno, whether it depends of soft or not, but when battery below 15% (or 10%) LED should be red. For mine device it's so.
Click to expand...
Click to collapse
Thats true...

Categories

Resources