Related
into teeny weeny little pieces.
I feel so much better now!!
Anyways...I have a wireless home network up and running and would like to connet the xda to it.
I can connect to the router no probs but IE cant connect to the web. it says "the page you are looking for cannot be found".
Any ideas why I can connect to the router but not to the web?
Cheers folks - thanks
I know how you feel. There are a couple things you have to do.
First check that you have selected to connect via "work".
Then ensure that the IP address shown is in the range of 192.168.0.X
had no problems with my wifi on my home network, as ale210p said, I think it's with the way your connect via "work" or "ISP" is configured
hiya folks
thanks for coming to my rescue..hopefully i can get this thing on the road.
- in connections - advanced - select networks. both selections are set to "my work network"
- in configure network adapters - network adapters. the "my network connects me to" dropdown is selected to work.
- where can i check my ip address on the device?
Alhtough I am connected to my wireless network as that what the wireless LAN manager says?
any ideas guys?
many thanks
Is your internet provider checking the MAC address? my provider checks for the MAC address and hence I had to register my MAC address first with the provider.
I'm pretty sure my ISP isnt checking my MAC address as my PC and other computer on the network work fine with regards to internet access and I never gave the MAC addresses to the ISP.
However, my modem router does have mac filtering enabled. I have copied the MAC address of the xda to the allowed list. However I've also tried to turn this filter off and the result was the same....I still could connect to my home wireless network but had the same error message when trying to surf through pocket IE.
Any other ideas on why I can connect to the network but IE wont let me surf?
thanks again
I'm having exactly the same problem as Richard. What I don't understand is, I can drive around and find free residential wireless hotspots and surf the net , but I can't do it on my own WLAN!
IP info OK?
These symptoms could indicate that vital IP info is missing on your XDA.
Does your XDA get an IP address + gateway address + DNS server address from the router's DHCP server? Use vxIPConfig to determine this http://www.cam.com/windowsce.html
I know for a fact that many times (not always) my QTEK 9090 does NOT get the required IP info from my SMC Barricade 2804WBR b/g wireless router, so I started using fixed addresses on my QTEK.
If I use DHCP, many times I can connect to the router but am unable to access the internet... Because the QTEK has not received an IP address/gateway address/DNS server address in those cases. Fixed addresses always work.
whoa
thanks for the advice. i installed the app. rubbed the sticks together and there were sparks i tell you!!! but what does it all mean?
the ip address is 169.254.84.245
subnet mask 255.255.0.0
dhcp server 255.255.255.255
im no tekkie so am not sure what the above means? does it provide any clues?
thanks for the advice so far
just an update
i manually inputted the ip address assigned to my xda by the router as i have dhcp disabled on the router.
nonetheless it sill doesnt let me connect to the net but i can connect to the wlan?
richard321_blue said:
just an update
i manually inputted the ip address assigned to my xda by the router as i have dhcp disabled on the router.
nonetheless it sill doesnt let me connect to the net but i can connect to the wlan?
Click to expand...
Click to collapse
Fixed IP address is good, but have you also put in the gateway address and DNS server address? Normally the gateway address + DNS server address = router address.
If your routers IP address would be 192.168.1.1 (quite common address), then your IP address could be 192.168.1.2, gateway address would be 192.168.1.1 and DNS server (name server) address also 192.168.1.1.
BTW; this:
the ip address is 169.254.84.245
subnet mask 255.255.0.0
dhcp server 255.255.255.255 <========= !!!!
means that DHCP didn't work!
I suppose that when you state "connect to the wlan" you mean that you can 'see' machines on your local network? Or what? That would make sense because you wouldn't need a gateway address and DNS server address for that normally (broadcasts).
siliconaddict....you're a genius!
finally it works, it works i say.
fantastic.
thanks to all for the advice and feedback - much appreciated.
can i stoke the fire and ask how i can sync via wifi as well?
never done it myself, but here is a guide
I have never synced over WiFi myself, but here are some guides:
http://theillustratednetwork.mvps.org/WM2003/ActiveSync/WM2003ActiveSyncConfiguration.html
http://forum.xda-developers.com/viewtopic.php?p=132820
Please note that the next version of Activesync, version 4, doesn't do syncing over Wifi anymore...
Good luck!
Sorry to be a complete noob, but:
1. How do I find out the IP Address of the XDA (Is it in Wireless LAN Manager, under "current config" and "IP:"?)
2. My Netgear USB WLAN is showing an IP of "0.0.0.0" (on command prompt >> ipconfig) How do I change this?
Thanks
Q & A
A 1: On your PDA use Use vxIPConfig for this http://www.cam.com/windowsce.html. Unfortunately the OS doesn't have a standard utility for it, like 'ipconfig'.
A 2: Does your router hand out IP addresses at all? Or: is DHCP enabled on your router? If true, do you have the correct drivers loaded for that USB NIC? In Device Manager how does it look? Yellow exclamation mark? Can you post the output of 'ipconfig /all'.
Done a search on various site but still no joy.
Just got a o2 XDA Mini S yesterday.But I cannot get it to connect to my wireless network at home.Its an open network, with a laptop,3 PC's,2 xbox's accessing it various times of day.All connect no problem.
My xda says my network is available,but cannot connect to it. Do I need to put in IP addresses in manually ? On the network cards section, it the SDIO WLAN wireless adapter that is used ?
Have tried allsorts,
First Question,
Is your WiFi router set to DHCP mode. If so then check that your device is also set to DHCP mode. If not change router to DHCP check that all your other devices are set to DHCP then you should automatically be allocated an IP address. A useful utility is WiFi Companion.
This scans for available networks and allows you to connect. it will also show you the IP address you have been assigned.
You could assign an IP address manually but this will have to be changed every time you walk on to another network. DHCP is better.
Regrads
Thanks for the info DW, it is my router,popped round a mates last night and it connected to his network ok.
Will check what you said and the firewall
not sure by what you mean exactly by open network.
but are you using MAC address filtering?
when I got the Sony Laptop, I was so eager to get it all setup etc, that I forgot bout the filtering, it would see the network, but refused to connect.
I'm having the same problem. My Exec can see the network but not connect. I investigated it a bit more and for some reason it keeps trying to use the same IP address as my laptop. It also cannot connect to the net to update Avant Go when it's syncing (via my laptop).
I've tried connecting with all other devices switched off, to avoid the IP address conflict, but still cannot connect to the internet.
I'm pretty much stumped.
Setting the Wireless power setting for best performance was the trump for me.
On my Vario - Settings - Connections - Wireless LAN - Power Mode
Thanks for the suggestion. I gave it a try but unfortunately it didn't help.
If my laptop is switched off my Exec can connect to my D-Link router, but I cannot access any internet resources. I presume that somewhere in the settings is the solution but I can't find it.
EXCELLENT db44!!!
For some reasons setting wireless "best performance" wortked for me too. Wizard (QTEK 9100 - gray market I guess as QTEK did not register on their site for me). I will still try Opera too.
Kind regards,
Oleg.
www.nano-science.com
same thing happened to my qtek. it detected the network but could not connect and sometimes when it got connected, i still couldn't surf the net. is there anything in the settings that i'm missing? i also tried to enter the IP address manually but no luck either.
My O2 XDA Mini arrived yesterday. It sees my wireless network (as well as two others in my neighborhood) but cannot/will not connect. I've tried everything I've read above - which confirms I'm on the right trail, but...
The D-Link DI-624 wireless router is in DCHP mode. I've dropped all security for connection trials. I've put the MAC address of the XDA in the router, just in case. I cannot find the IP address of the Mini (how do you do that?), but have tried with and without allowing the router to assign it a random and an assigned IP address. My router does NOT have the default (198.162, etc, etc IP address.) so I've been careful not to blindly follow standard instructions. Of course, I have tried with specific IP addresses, default gateway (router), etc, etc.
One clue is that after trying for a long time to connect to the networks it finds, I got one error message from the XDA saying it could not be assigned an IP address from the network(s). Good clue - wish I know what it means.
There are only limited settings to check on the XDA, so I'm wondering if I'm missing something on the router. Any ideas? Many thanks.
Im looking to get the Wifi working on my Vario at home. My current Access point wont connect due to T-mobile's lock out of the 802.11g.
So I can get a Access point that works, I thought it would be helpful to post up your Model with a Yes or No after you have tried all the different settings as posted on the forum e.g. different channels and mixed mode etc.
This is for g Locked Varios only please not ones with flashed ROMs.
Please keep it simple Model YES or NO.
Thanks
:wink:
To Start us off......
Inexq HR054g Access point (NO)
if your Wizard has b only (ROM issue, not hardware) then ANY router which is set to allow g only will fail to connect. yours "should" allow "b" devices to connect http://www.inexq.com/web1/images/product/spec/hr054g.htm
So maybe you have a setting that is allowing "g" only
Beeble said:
if your Wizard has b only (ROM issue, not hardware) then ANY router which is set to allow g only will fail to connect. yours "should" allow "b" devices to connect http://www.inexq.com/web1/images/product/spec/hr054g.htm
So maybe you have a setting that is allowing "g" only
Click to expand...
Click to collapse
Router is set to mixed mode, it can see the network but wont connect
Have you got MAC address filtering enabled on your router and forgotten....I did.
Also try changing WLan card settings on your XDA from Best battery to best performance..Make a lot of difference. and many have found theirs connects after this
All turned off any other options
I have a BT2100 wireless router and mini-s, sometimes it won't connect until I stop active sync running on the mini-s ???
3-Com OfficeConnect ADSL Firewall Wireless 11g Router (set to mixed)
Vario will only connect when router set to open access i.e. security disabled. Any other setting i.e. WAP, WEP causes the routers internal DHCP server to fail to send an IP address back to the Vario... or the Vario being unable to acknowledge the router?
Have got a couple more routers comming my way, will post them up when Ive had a chance to test them
devasoftware said:
3-Com OfficeConnect ADSL Firewall Wireless 11g Router (set to mixed)
Vario will only connect when router set to open access i.e. security disabled. Any other setting i.e. WAP, WEP causes the routers internal DHCP server to fail to send an IP address back to the Vario... or the Vario being unable to acknowledge the router?
Click to expand...
Click to collapse
I've seen this issue detailed elsewhere but I can't remember exactly where - apparently for some reason the 3com sends back an IP v6 address when security is enabled, which the Wizard can't use.
So far I've used a cheapie Origo wireless router (conexant chipset) and a Netgear D834G (in mixed mode), my Wizard seems happy with both.
John
i must have jacked something up. first i could not get a wifi connection at home, then i flashed the firmware on the device and asked it to use the mac to connect with static IP and now the pda browsers cannot get any DNS info
netfront states no dns server specified and wireless router log states DHCP Discover no response.
must be a setting somewhere i'm missing.
wireless laptop and wired pc working fine
you can really just use the ip of a known dns from the device too
all dns servers should respond from all devices asking for the ip given the hostname
setup
cable modem to wired linksys router (DHCP on) - DI-524 wireless router connected to wired router (DHCP on)
when you say 'known IP from device' you mean the wireless router? Do you mean have the wireless router give the PDA my ISP's DNS IP?
if so what happens to my ability to browse the LAN since the devices IP is now out of the scope of my LAN
SORRY I THINK I MEAN the error is
<< DNS Discovery no repsonse. >>>
basically no DNS server found when browsing with the PDA when connected to WLAN.
PDA is ok browsing when I connect to work routers. I'm getting IP ok from home wireless dlink router but router cannot give the PDA a DNS server.
ps- wireless laptop ok for DNS connecting to the same wireless router so i'm thinking the firmware update made the dlink not like the PDA
update- i think it's the device and a setting.
now i cannot get to the internet through netfront or ie at work connected to wifi router. same error
DNS no server is specified
can get anything by IP, is wm5 wifi challenged for internet access?
any takers?
Hi all
Ive just brough a new belkin wireless n router set it up as you should connected my laptop my brothers laptop my desktop my ipod touch but my MDA touch will not connect to it. My touch connects to my other trendnet router fine and all other AP i have tryed. what is really bugging me is that when i try and connect to my new belkin it wont let me connect to any other routers so i have to delete the belkin router from my device and soft reset
i am starting to think it could be a faulty router or mda
Same boat....
I have the same issue with my HTC Kaiser, can see a host of AP/Wireless Routers via the Wi-Fi card but fails to connect to my Belkin F5D8631-4 v3 N1 Wireless Modem Router, a real pain in the arse considering the price I paid for the router, everything else connects, PC's, PS3, 360, DS Lite, PSP the lot....all bar the Kaiser.
Anyone managed to find a solution to this issue and sitting on it
Before you ask, no security enabled, only using the MAC address filtering to do the job of keeping unwanted off my network, even with this turned off the Kaiser see the network, flags it up as available but will not connect....
Any help gratefully received
Connecting
I bought a sitecom mimo XR router, I have got the same problem with a Qtek 9090.
The solution I found is, dont activate dhcp on your device but manually add the ip adresses of your router and device, set the dns server ip-adress to the ip-adress of your device.
Worked for me.
royaldutch51 said:
I bought a sitecom mimo XR router, I have got the same problem with a Qtek 9090.
The solution I found is, dont activate dhcp on your device but manually add the ip adresses of your router and device, set the dns server ip-adress to the ip-adress of your device.
Worked for me.
Click to expand...
Click to collapse
Thanks for the feedback/comments
I have done (I think) correctly and its still not playing ball, just to confirm the actual detail:
Router Set Up:
DHCP Activated ? (it is currently)
All WEP/WPA turned off
MAC address filtering turned on and the MAC adress for the hand set network card (found by
on to Com Manager, Settings, Wireless Lan, Advanced Tab) is on the list on accepted MAC address on the MAC filter
Handset Settings
Wireless Network Adapter settings (on Configure Network Adapters page)
IEEE 802.11b/g Compatible Wi-Fi
User Specific IP address 192.168.2.50 (not an address allocated by DHCP)
Subnet Mask 255.255.255.0
Default Gateway 192.168.2.1 (IP address of the Router)
Primary DNS 192.168.2.1 (IP address of the Router)
I get the same sort of problem occasionaly with my universal. The only thing that sorts it out is deleting any reference to the connection then removing the battery. This seems to flush out the system & then it finds it a new connection & connects straight away, worth a try if nothing else works.
JohnWB said:
I get the same sort of problem occasionaly with my universal. The only thing that sorts it out is deleting any reference to the connection then removing the battery. This seems to flush out the system & then it finds it a new connection & connects straight away, worth a try if nothing else works.
Click to expand...
Click to collapse
Thanks John,
I did try this, and it didn't make a difference.
You know when you get that feeling you are going to have to admit defeat....
Any solutions so far
Guys,
Does anyone has a solution so far?
What version of Windows mobile are you running?
This post in the Shift forum
http://forum.xda-developers.com/showthread.php?t=384730
mentions a beta firmware on Belkins UK site which solves the problem.
hi, i'm using a mda vario 3 with an older Belkin router and it works fine. I have the dhcp server turned off with all the ip's set manually. the ieee 802.1 auth thingy is not selected. other than that my settings are similar to those posted above. Although i have wep security set up. (Nintendo ds's only do wep)
Corrykid said:
What version of Windows mobile are you running?
Click to expand...
Click to collapse
I run Windows Mobile 6.1
When I ran Windows Mobile 6.0, I did not have contact with my Sitecom WL-173 router either.
tembares said:
Guys,
Does anyone has a solution so far?
Click to expand...
Click to collapse
I have found the solution.
Just upgrade the radio to 1.64.08.21.
Then it works.
wifi problem
just upgraded my MDA to wm6.1 and i encountered a problem regarding with my wifi connection.
having my old wm5, i dont have any problem connecting to my wireless router(d link) but when i upgraded my wizard to wm6.1, at first it will connect for about 20sec then the connection will drop and i cant connect anymore. but my wizard detects my router but it just on the screen that it is unavailable even though it shows a very strong signal.
i've tried to hard reset it and it doesn't work. i just wondering if there's a configuration i should do with the setting of my wifi? or is there an application that i can download here? and also i lost the voice tag program of my phone when i upgraded it to wm6.1, where cant i download an application for it?
thank you in advance!!! ([email protected])
Customer Call Details Nov 13 2008 04:37
I have an HTC Touch that can connect to other hotspots, but not to my home Belkin router. Sometimes, if there is another connection available, it can see the router, and says that it is Available, but cannot connect; other times it won't even see it. I have checked for firmware updates, but I have the latest. Any help would be greatly appreciated.
Belkin Response Nov 14 2008 22:18
Hi Lilburd,
Thank you for contacting Belkin Technical Support.
We understand that the HTC Touch does not connect to the router. We apologize for the inconvenience caused.
Please follow the steps given below to update the firmware and configure the router:
We recommend that you update the firmware from a computer that is connected to the router with an ethernet cable.
Please download the latest firmware on the router from the link given below. Download the file "3.01.29":
http://www.belkin.com/uk/support/article/?lid=enu&pid=F5D8233uk4&aid=10288&scid=0
and save it to the computer.
- To update the firmware, log on to the router`s web interface by typing in http://192.168.2.1 in the address bar of the browser. The computer should be
connected to the router with an ethernet cable.
Note: If you have changed your Router’s IP address, use that IP address.
- By default, the password is blank. Click the "Submit" button.
- Click on "Firmware Upgrade" under the option "Utilities".
- Click on “Browse” and select the bin file that you have downloaded.
- Click on “update” and follow the wizard.
- After updating the firmware, restore the router to factory defaults by clicking on "Restore Factory Defaults" under "Utilities".
- Reconfigure the router.
Please follow the steps given below for configuring the router:
- Connect the computer to the "LAN" port on the router and connect the modem to the Internet/"WAN" port, using Ethernet cables.
- Take a paper clip, insert the paper clip in the reset hole of the router and hold it for 15 seconds.
- The power light will flash and then come back "ON" solid, indicating that the router is being restored to factory defaults.
- The corresponding lights on the front of the router should be lit up.
- On the computer, check if you have an IP address in the range of 192.168.2.x.
- If not, specify a static IP address, gateway and "DNS" address by following the steps given in the link-
http://web.belkin.com/support/kb/kb.asp?a=2824
- Log on to the router web interface by typing in http://192.168.2.1, in the address bar of your browser.
- By default, the password is blank.
- Click on "Connection Type" in the left hand column under "Internet WAN" heading.
If the connection type is Dynamic (cable):
- Choose "Dynamic" and then click on "Next".
- Type in your “Host Name”, if your Internet Service Provider has provided it. Else, leave it blank.
- Click on "Change WAN MAC Address".
- Click on the button "Clone".
- Click on "Apply Changes".
If the connection type is PPPOE (DSL):
- Choose "PPPOE" and click on "Next".
- Enter the user name and password given by your Internet Service Provider.
- Save the settings.
- Click on the "Home" link at the top of the screen.
Internet Status should show "Connected" on the top right hand corner of the web page.
If the problem persists, please get back to us with the following information:
1. Type of connection provided by your ISP (Is it PPPOE, Dynamic or static).
2. Name of the Internet service provider (ISP).
3. Version number of the router. You would find the version number on the bottom of the device. It would be a number in a series of thousands with a prefix “ver.”.
4. If the internet connection is stable on the computers using the router?
5. If the HTC Touch detects and connects to other networks in the neighborhood?
Lilburd, if you need further assistance please feel free to write back to us and we will be happy to assist you.
Regards,
Belkin Technical Support.
This was the response I got from Belkin after emailing them. It worked like a charm
Registry option
Not Sure about this one, but if you use SK Tools, or find the registry values yourself, there is an option to activate on the Touch, the 801 g networks compatibility, for some reason they are compatible but the option comes 'off' by default.
Paul
THANK YOU - Wizard 9100 now connecting to belkin N1
thank you - I had the same problem as original post - I updated using the pre release belkin firmware and it works now.
Excellent!
I was pretty sure that it was an incompatibility issue between HTC and Belkin.
Thanks a lot for this patch, you saved my (wifi) life ^^
This update also worked with my Kaiser! I was pulling my hair out trying to get it to connect. Thanks a lot!