Hi!
I'm using the latest QTEK ROM with A2DP.
The problem is that my set blacks out at 38% battery power and refuses to power up after that unless I re-connect to the AC for charging. It happens a couple of times already. Any setting(s) in the Universal to check this?
I remember I managed to get the battery level at real low level (less than 5%) previously prior to the ROM upgrade.
Thanks
Hi,
I have a similar problem.
I charged the unit till 100% then reflush the Rom
Regards
JoseF
RE
Hi JoseF
Thanks, however, I'll consider this as my last option
Meanwhile I would like to get more feedback on this issue
Qtek 13077 ROM ????
My i-mate continues to crashes with the battery is less then 43%, apparently the problem occurred when I made the upgrade to ROM Qtek WWE_13077_130176_10900, was looked like that this version has something that change the battery configuration, since Qtek 9000 comes with 1750 battery mAh? I reinstalled the i-mate ROM 1.30.82 and the problem persists?
I made a test leaving the i-mate on, without using the radio until the battery miter showed 23%, then I made a phone call, the i-mate crashes in seconds. Could somebody inform what is the true voltage of the battery in the i-mate is 100% and when it is 10%, in the miter?
I have charged the unit till 100% led = Green, then soft reset, the problem persist?
Now I am 100% certainty that the problem occurred when I made upgrade for Qtek, we needs to investigate what the the Qtek ROM this doing with the JasJar?
Ive 3 batteries
The standard 1620mah dynapack which works fine 100% to flat no worries
A 3200mah extended which will charge to full but dies at 43%
(the guy replaced it with another which did the same thing)
and
A 3000mah which will go flat ok but wont charge beyond 47% and the orange light stays on forever, although luckily it doesnt fry.
has anyone had any of these extended batterys work ok?
Just to add a bit of info, all modern li-ion have a built in fuel guage chip which tells the device its in how much power is left in the cell. so its possable this is a battery issue rather than phone problem
r 1.03.00
g 42.36.p8
d 1.30.90.wwe
RE
You may be right about the battery thing
However, I've tested my existing battery to very low level prior to the ROM update without problem
And with other feedbacks in this forum I doubt it could be a coincidence that our batteries are having the same issue.
I would rather think its a ROM thing.
I'll need to test my battery on another Universal before confirming.
I just tried to flash to an older rom but got a country error, there seems to be no old orange uk rom i can find.
Im a bit new to all this rom flashing business and also wanted to try an older rom to check out the camera as im not sure if i have a realy poor camera or if there is a software issue with that in the new orange rom also as one guy in another post is getting far better results out of his camera mines like a real snow storm in the dark parts of pictures
RE
Yes, the new QTEK ROM update does cause the camera quality to suffer especially when in night mode
Well, just have to wait for another ROM update to resolve these issues :roll:
Fosa or Zarn
You have a digital multimeter?
Case yes: You it could measure the voltage of the battery when is total loaded 100% led=green, and when the battery will be flat 0%. This test would be excellent to verify if the Battery power remaining is correct. Currently when my battery is with 3.28V = 55% in the battery power remaining = crashes.
ok, can do, not that it will help much unloaded.
I'll charge the original cell and post the results shortly.
The battery management wont always turn the battery off at the same point as the battery ages it will change. You have to bare in mind that a battery is a little like a piece of rubber the harder you push on it the bigger the dent but when you stop pushing it recovers its shape.
The same goes for the voltage of a battery, when you draw a large current the voltage will drop further than if the device is in standby but once you disconnect the load there will be an amount of recovery
li-ion batterys are far more complicated than they first appear.
The battery is by no means connected directly to the phone.
there is a microprocessor in the battery that controls both charge and discharge via 2 fet transistors, buy doing this it protects you against the battery exploding/catching fire from over charging or over discharging.
As far as im awaire the microprocessor will adjust both switch on and switch off from many variables not just voltage drop.
The phone its self mearly supplies power to the charger built into the battery and draws power from the battery all the measurement and battery managment is within the battery
This is why the battery suddenly just stops and you need power to bring it back to life.
so in theory no matter what the condition of the battery it should always give a full scale deflection from full to empty as the onboard management should know how much capacity is left in the cell and report this via the data lines to the phone
If you connect a bulb to an almost flat li-ion battery you will find little drop in brightness before the battery just cuts power totaly to protect the cell within from over discharge.
Something that springs to mind that hasnt been mentioned here is have you checked all 4 battery contacts are clean? just a thought because the two larger outer pads provide power while one or both of the smaller pads send data on the charge status to the phone.
heres some interesting reading
http://www.batteryuniversity.com/parttwo-34.htm
Intresting reading on the care of li-ion as they dont like being either fully charged or fully discharged..strange eh...
http://www.maxim-ic.com/appnotes.cfm/appnote_number/128
http://www.intersil.com/data/an/AN1174.pdf
two examples of li-ion battery management.
safety law dictates any li-ion that is user replaceable must have one of these little chaps built in.
hope that makes sence
/ramble
RE
Sorry zarn, but I don't have a digital multimeter.
Is your test going to prove that the battery is going to its end of life soon?
How could that be since the Universal is less than a year old? :roll:
At any rate I'll be testing my battery on another Universal without the QTEK ROM update to determine whether its a battery issue or the ROM update issue.
Im just going to do it out of interest... like i said in the previous post its not likely to prove anything except if the guys battery is totaly out of whack
Dear Fosa and Zarn,
I’ve already known those URLs:
http://www.batteryuniversity.com/parttwo-34.htm
http://www.maxim-ic.com/appnotes.cfm/appnote_number/128
I liked very much this article:
http://www.maxim-ic.com/appnotes.cfm/appnote_number/128
However, when I asked to verify the voltage of the battery and without taking it off the charger, I’ve put two tiny wires on the terminal of the battery, in the manner I could verify the voltage without taking it off from the Jasjar. Last night I’ve left it charging until the green-led light and I’ve noticed that the voltage was 4,231V = to 100% on the battery power remaining miter.
I’ve did a test putting the light of 4V to discharge the battery, and at the 2,83V, it disconnected automatically (stopped to supply current). In more or less one minute, it starts to provide energy again, in other words, the protection circuit of the battery is Ok, and is not with this tension (2,83v) that the Jasjar stops, and only when is 3,28v.
I’ve got the feeling that the problem is on the ROM, however I did reinstall the original ROM and yet the Jasjar still crashes at 58% of the battery(= 3,28v).
Before making the upgrade the miter was going from 100% to 5% without crashing.
With the ROM Qtek WWE_13077_130176_10900 the miter shows 100% to 42%, and at this point it starts to crash.
I’ve already bought a new battery just to test it, but it still not arrived from Hong Kong, and as the customs is on strike here in Rio de Janeiro, Brazil, I don’t know when I’ll get it.
Until now I think the problem is that the Qtek ROM made some changes on the firmware or in the register of the battery, changing the miter calibration.
Battery results
Im suprised it cut of that low, thats very low for a 3.7v li-ion, thats more what you would expect from a 3.2v.
Anyways, as requested heres the resuts of checking the voltage at various points.
This is using an original dynapack 1620mah battery as supplied by orange with the phone, but its around 3 or 4 months old now so far from fresh.
the meter used was a Avo M801 (not a cheap one though is probably due to be calibrated...)
100%----4.16v straight off charge still warm
75%-----3.93v
50%-----3.78v
38%-----3.76v
25%-----3.73v
10%-----3.65v
5%------3.63v
cutoff----3.58v
Im going to do the same with the extended batterys im having problems with just as a comparison, will post the results here if anyone is interested
Whats going off here...?
I just put one of the extended batterys in which was fully charged..
to be greated with a blank batery bar, and unknown in the chargeing remaining window... unpluged and repluged the charger and was then told battery at 225%
doh.....
Jasjar battery miter
Hi Zarn
Thanks a lot for the table of % * V, now I am certain convinced that the Jasjar miter needs to be calibrated again, I believe that the problem is the DLL or the responsible register for this detail(miter)?
While I or somebody of the forum does not find the solution, I will continue using this way, because the battery still lasts for 24h.
RE
OK guys, bad news
I used my battery which knocks out at 43% from my QTEK 9000 set and put it into another QTEK 9000 set without ROM update and it also fails to boot up unless I connect it to an external power
I hope that QTEK can release a small ROM update to resolve this issue
so hang on..
you put your battery into another non updated rom handset and it still wasnt working properly...
surely that means your battery is at fault not the rom..
cant u borrow the other guys battery for a few hours?
Are these original batterys were talking about btw (1620mah dynapacks)?
or cheap replacements?
RE
Hi zarn,
My battery is the original default battery....the Universal is less than a year old
Could it be that the new ROM update has changed something in the battery...maybe the IC chip in the battery, if any?
RE
zarn,
If you'll read another similar thread you'll find many others with different variants of the Universal facing the same problem after upgrading the new QTEK ROM update with A2DP
Are you saying their batteries are faulty too...such a coincidence?
hi all i'm new here.
I'm a new user of tytn or better voda v1605. i have a big problem:
the battery life is about 3 hours. i have 3 battery, one original (1350mah) and 2 commercial (1500mah). when i put the phone in charge te battery gone very hot.
When i turn on the pda when battery gone down to 60% (in about 1 hour) the battery gone very hot about 40° celsius or more and it discharge faster. My friend have the same tytn but it works better, the battery duration is about 1 day an half using it normally. anyone know what, or where is the problem? it looks like an hardware problem, and i need help to fix it
i have official htc wm6 installed on it
thanks all
Hi guys i have some serious battery drain on my new touch hd, last night the phone had 40% and this morning it was dead, this is with a brand new high capacity 2400mah battery, i have data turned off as well as the screen.
I am running stonehenge 6.5 rom with cookie home tabs.
anyone got any ideas?
cheers, thedexter
change rom
turning off the display and wireless connections is one way to save power, but still the battery usage can be easily estimated by having a look at the cpu and ram usage. i for one use the stock rom, and when there are no apps running in background, my ram usage is at 35%, given that you are using wm6.5 and cht, i guess it would revolve around 60-70%, so indeed, to save power, a rom change might be helpful.
thanks for the suggestions guys
flashed a new rom version and downgraded radio to 1.14 and battery life was about the same, then i followed the battery calibration wiki and charged the phone whilst it was switched off and my battery life is looking much better.
cheers, thedexter
Hi everyone,
I recently bought a HP ipaq 614C. I flashed the original firmware on it and I noticed that the battery drains fast. Also now when I got a cooked rom on it. When I work on it, the battery won't be able to give enough power for half a day.
Now I wonder if I should buy an original HP battery or just a imitation. Is there a difference in quality?
edit: I just noticed that in about 10min 10% battery has gone when wlan is enabled and no heavy programs are used.
Samuel
http://http://compare.ebay.co.uk/like/200637651541?ltyp=AllFixedPriceItemTypes&rvr_id=279472601150&clk_rvr_id=279472601150&crlp=1_262531_281231&UA=WXF%3F&GUID=616189c31270a0e202849ea4ff897ebd&mt_id=775&query=%7Bquery%7D&fitem=200637651541&kw=%7Bquery%7D&ff4=262531_281231
Hi everyone!
Wondering if there is or are anyway to calibrate Omnia battery? I think it is draining too fast, first i left my phone charging for 5hours to completely charge and just send 1 message and download Samsung App "Now" and in 1 hour since has now 92% of it. I use brightness in minimun, use Edge connection and nothing more to spend so much...in moment im using "mirolg" mi7ROM mango 8107 DFT, great by the way!
Any ideas?
Thanks!
after each ROM flash i recommand the battery dicarger tool from MS Market Place.
really it works, really! It allow the battery circuitry to calibrate to the right energy level.
After flash a ROM, I let the battery completly discharging and then I charge my device for minimum 8 hours. then on 30% battery level I repeat this process. my battery has 40 - 50% longer life with the same usage.
"Even though lithium batteries don't have the memory effect issue, they still have a phenomenon called state-of-charge (SOC) mismatch. Battery Discharger employs various hardware resources available on the phone to discharge the battery power at a faster but controlled rate. Charging the phone completely from this state would allow the microprocessors on the battery circuitry to recalibrate and start reporting accurate energy levels.
Battery Discharger is a smart app that lets you discharge the battery of your phone at various discharge rates in a controlled manner. User can configure Battery Discharger app to use one or more of the following hardware resources to achieve the optimum discharge rate"
Thanks for your suggestion, miro!
I tested the application you mention and it works really well.
First thx miro for a great rom, this tip gives me 4 Hours more power !!!