Few days before, my 6700 is down. After warm boot, it show R NONE and no P item. Use RUU_noid tools to flash other radios (1.10, 1.27, 1.43) and nk.nbf many times, it still like before. It can boot wm5 and can't use phone call. And it return to normal CID (it's superCID before).
Use mtty.exe and get into bootloader mode, it show below:
USB>info 0
APACHE
USB>info 1
1.00
USB>info 2
Wait interpreter timeout
HTCS ?襱HTCE
USB>info 3
HTCSP1.00 YHTCE
USB>info 4
HTCS L?HTCE
USB>info 5
USB>info 6
HTCST 谌HTCE
USB>info 7
HTC Integrated Re-Flash Utility for bootloader Version : 1.40h, APACHE HW Version : 1.00
Built at: Aug 31 2005 12:04:54
Copyright (c) 1998-2005 High Tech Computer Corporation
Turbo = 312 MHz, Run = 208 Mhz
Memory Frequency = 208 MHz
SDRAM Frequency = 104 MHz
Board ID is 2, Display is 0 (0=Ty,1=Sg)
USB>
Could somebody help me to fix it? Thanks a lot!
Related
Hello,
I have bricked Typhoon MyGuide 5500 XL pocket. Even it is based on ASUS 620, according to the site:http://www.handhelds.org/moin/moin.cgi/MyPal620JTAG I wasn't able to flash it.
Here is snapshot from jtag:
jtag> detect
IR length: 5
Chain length: 1
Device Id: 01101001001001100100000000010011
Manufacturer: Intel
Part: PXA250
Stepping: PXA255A0
Filename: /usr/local/share/jtag/intel/pxa250/pxa250c0
jtag> print
No. Manufacturer Part Stepping Instruction
Register
---------------------------------------------------------------------------------------------
0 Intel PXA250 PXA255A0 BYPASS BR
Active bus:
*0: Intel PXA2x0 compatible bus driver via BSR (JTAG part No. 0)
start: 0x00000000, length: 0x04000000, data width: 32 bit, (Static ChipSelect 0)
start: 0x48000000, length: 0x04000000, data width: 32 bit, (Memory Mapped registers (Memory Ctl))
jtag> detectflash
jedec_detect: mid 4, did ea00
Flash not found!
In internet I found another guy who faced the same problem (mid 4, did ea00), so it might be that it is something Typhoon specific, because I checked/fixed five times my cable, trying to make it as short as possible, then changed all the possible LPT modes (SPP, EPP, etc), then tested it with XP/SP2+Cygwin and Linux (Fedora Core release 2 (Tettnang), kernel 2.6.5) separately. The same problems. The flash is not recognized.
Can I pass some commands using jtag to the processor and in such way to manipulate with flash? What kind of commands? Where I could read about them?
Can I change BOOT_SEL[0] value to 0, which is now 1? Will it help?
Or do you know some more hints to make jtag to recognize my flash (M-SYS DiskOnChip G3)?
Thank you
I just found a free benchmark testing program running on my shift.
The result as below shows the details of my shift. Is that help for looking for the drivers?????
I use the CrystalMark to make the test.
http://crystalmark.info/download/index-e.html#CrystalMark2004
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
CrystalMark 2004R3 [0.9.124.404] (C) 2001-2008 hiyohiyo
Crystal Dew World [http://crystalmark.info/]
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
------------------------------------------------------------------------------
CrystalMark Result
------------------------------------------------------------------------------
Display Mode : 800 x 600 32bit (ClearType)
CrystalMark : 11921
[ ALU ] 2203
Fibonacci : 852
Napierian : 392
Eratosthenes : 337
QuickSort : 600
[ FPU ] 2295
MikoFPU : 251
RandMeanSS : 1101
FFT : 456
Mandelbrot : 465
[ MEM ] 2126
Read : 774.13 MB/s ( 774)
Write : 571.23 MB/s ( 571)
Read/Write : 531.52 MB/s ( 531)
Cache : 2280.63 MB/s ( 228)
[ HDD ] 3032
Read : 19.69 MB/s ( 787)
Write : 13.41 MB/s ( 536)
RandomRead512K : 11.85 MB/s ( 474)
RandomWrite512K : 11.86 MB/s ( 474)
RandomRead 64K : 13.39 MB/s ( 535)
RandomWrite 64K : 5.65 MB/s ( 226)
[ GDI ] 1204
Text : 346
Square : 120
Circle : 412
BitBlt : 326
[ D2D ] 652
Sprite 10 : 199.44 FPS ( 19)
Sprite 100 : 102.73 FPS ( 102)
Sprite 500 : 25.33 FPS ( 126)
Sprite 1000 : 12.87 FPS ( 128)
Sprite 5000 : 2.77 FPS ( 138)
Sprite 10000 : 1.39 FPS ( 139)
[ OGL ] 409
Scene 1 Score : 250
Lines (x1000) : ( 16053)
Scene 1 CPUs : ( 4)
Scene 2 Score : 159
Polygons(x1000) : ( 3419)
Scene 2 CPUs : ( 4)
------------------------------------------------------------------------------
System Information
------------------------------------------------------------------------------
OS : Windows Vista Business [6.0 Build 6000]
Display Mode : 800 x 600 32bit 60Hz
Memory : 1022 MB
DirectX : 10.0
------------------------------------------------------------------------------
CPU
------------------------------------------------------------------------------
CPU Name : Intel Pentium M (Dothan)
Vendor String : GenuineIntel
Name String : Genuine Intel(R) processor 800MHz
Platform : Socket 479
CPU Type : Original OEM processor
Number(Logical) : 1
Family : 6
Model : D
Stepping : 8
BrandID : 15
Feature : MMX SSE SSE2 XD
Current Original
Clock : 600.00 MHz 800.00 MHz
System Clock : 100.00 MHz 100.00 MHz
System Bus : 400.00 MHz 400.00 MHz
Multiplier : 6.00 8.00
Data Rate : QDR
Over Clock : -25.00 %
L1 I-Cache : 32 KB
L1 D-Cache : 32 KB
L2 Cache : 512 KB [Full:600.00 MHz]
------------------------------------------------------------------------------
Device
------------------------------------------------------------------------------
ChipSet : Intel 945GM Express
North : Intel 82945GM
South : Intel 82801GBM (ICH7-M)
IDE Controller : Intel(R) 82801G (ICH7 Family) Ultra ATA Storage Controllers - 27DF
------------------------------------------------------------------------------
Graphics
------------------------------------------------------------------------------
Video : Intel 82945GM GC (GMA X950)
Video Product : Mobile Intel(R) 945 Express Chipset Family
Video Vendor : Intel Corporation
Video Chip : Intel(R) GMA 950
Video RAM : 256 MB
Driver Version : 7.14.10.1437
Driver Date : 2008/02/11
------------------------------------------------------------------------------
HDD
------------------------------------------------------------------------------
Type Size Model ( Buffer Mode )
IDE 35.4GB TOSHIBA MK4009GAL
0.0GB SD Memory Card
------------------------------------------------------------------------------
BIOS
------------------------------------------------------------------------------
Vendor : American Megatrends Inc.
Caption : Default System BIOS
Version : HTC - 1000816
Date : 2008/01/16
SM BIOS Caption : 1.0.0.18
SM BIOS Version : 2.5
------------------------------------------------------------------------------
Mother
------------------------------------------------------------------------------
Vendor : High Tech Computer Corp.
Product : Shift
Version : 0001
------------------------------------------------------------------------------
Computer System
------------------------------------------------------------------------------
Vendor : High Tech Computer Corp.
Product : Shift
------------------------------------------------------------------------------
CPUID Detail Information
------------------------------------------------------------------------------
0x00000000 : EAX=0x00000002 EBX=0x756E6547 ECX=0x6C65746E EDX=0x49656E69
0x00000001 : EAX=0x000006D8 EBX=0x00000815 ECX=0x00000180 EDX=0xAFE9FBFF
0x00000002 : EAX=0x02B3B001 EBX=0x000000F0 ECX=0x00000000 EDX=0x2C04307F
0x80000000 : EAX=0x80000008 EBX=0x00000000 ECX=0x00000000 EDX=0x00000000
0x80000001 : EAX=0x00000000 EBX=0x00000000 ECX=0x00000000 EDX=0x00100000
0x80000002 : EAX=0x756E6547 EBX=0x20656E69 ECX=0x65746E49 EDX=0x2952286C
0x80000003 : EAX=0x6F727020 EBX=0x73736563 ECX=0x2020726F EDX=0x20202020
0x80000004 : EAX=0x20202020 EBX=0x20202020 ECX=0x30303820 EDX=0x007A484D
0x80000005 : EAX=0x00000000 EBX=0x00000000 ECX=0x00000000 EDX=0x00000000
0x80000006 : EAX=0x00000000 EBX=0x00000000 ECX=0x02002040 EDX=0x00000000
0x80000007 : EAX=0x00000000 EBX=0x00000000 ECX=0x00000000 EDX=0x00000000
0x80000008 : EAX=0x00002020 EBX=0x00000000 ECX=0x00000000 EDX=0x00000000
------------------------------------------------------------------------------
PCI Device List
------------------------------------------------------------------------------
No Bus Dev Fnc VendorDeviceRev SubSystem Class DeviceType
0 0: 0: 0 8086h:27A0h.03h 55671001h 060000h Host Bridge
1 0: 2: 0 8086h:27A2h.03h 55671001h 030000h VGA Compatible Controller
2 0: 2: 1 8086h:27A6h.03h 55671001h 038000h Other Display Controller
3 0: 27: 0 8086h:27D8h.02h 55671001h 040300h High-Definition Audio Device
4 0: 29: 0 8086h:27C8h.02h 55671001h 0C0300h UHCI USB Controller
5 0: 29: 1 8086h:27C9h.02h 55671001h 0C0300h UHCI USB Controller
6 0: 29: 2 8086h:27CAh.02h 55671001h 0C0300h UHCI USB Controller
7 0: 29: 7 8086h:27CCh.02h 55671001h 0C0320h EHCI USB Controller
8 0: 30: 0 8086h:2448h.E2h 55671001h 060401h PCI to PCI Bridge (SSD)
9 0: 31: 0 8086h:27B9h.02h 55671001h 060100h ISA Bridge
10 0: 31: 1 8086h:27DFh.02h 55671001h 01018Ah Bus Master IDE controller
11 0: 31: 3 8086h:27DAh.02h 55671001h 0C0500h SMBus Contoller
12 1: 6: 0 1947h:4743h.09h 22114433h 080500h SD Host Controller without DMA
No DeviceName
0 Intel Mobile 945GM/PM/GMS
1 Intel Mobile 945GM/GMS
2 Intel Mobile 945GM/GMS/GME
3 Intel 82801G (ICH7 Family) High Definition Audio Controller
4 Intel 82801G (ICH7 Family) USB UHCI Controller #1
5 Intel 82801G (ICH7 Family) USB UHCI Controller #2
6 Intel 82801G (ICH7 Family) USB UHCI Controller #3
7 Intel 82801G (ICH7 Family) USB2 EHCI Controller
8 Intel 82801 Mobile PCI Bridge
9 Intel 82801GBM (ICH7-M) LPC Interface Bridge
10 Intel 82801G (ICH7 Family) IDE Controller
11 Intel 82801G (ICH7 Family) SMBus Controller
12 Unknown Unknown
Click to expand...
Click to collapse
nope, i don't think this will help much. the problem with drivers has already been discussed here on the forums. It has to do with powering on some devices, in original vista that was the job of that shag controll program. we need to port it onto xp to have touchscreen and wlan working. The other drivers are already ok.
Hi folks, after repeated attempts at last managed to change Product ID (SKU ID) in hw 6915, here history and how to do this to you. Before the code was from HP Asset viewer http://h18004.www1.hp.com/products/quickspecs/12352_div/12352_div.HTML FA736AA#ABB – Euro English After this procedure my product ID is FA123T#ABA
(thanks Himalaya & Andes developers from this forum for ideas)
need: MTTY
steps:
1: Bootloader
2: mtty
3: task 28 55aa (fully format device)
4: rtask 0 (reset radio)
5: Reflash device
Above from wiki XDA dev's
Important, do not try to start device after above, after radio reset, put device back to bootloader directly
If above does not help you need to reflow or reball radio chip (tested and working if above does not work)
And my result from MTTY:
task 32
USB>password BOOTLOADER
HTCSPass.< YHTCEUSB>info 8
DOCInfoTableinitHW+
Binary0 Size: 0x100000
FAT0 Size: 0x4000000
FAT1 Size: 0x3340000
All Size: 0x7440000
FAT0_ADDR=0x100000,FAT1_ADDR=0x4100000
USB>info 7
HTC Integrated Re-Flash Utility for bootloader Version:1.50a SABLE EVT version:G.39
MainBoardID = C
Built at: Jun 12 2006 13:46:04
Copyright (c) 1998-2005 High Tech Computer Corporation
Turbo Mode Frequency = 312 MHz
Run Mode Frequency = 208 MHz
Memory Frequency = 208 MHz
SDRAM Frequency = 104 MHz
USB>info 4
HTCS Lњ3ЖHTCE
USB>task 28
DOCInfoTableinitHW+
Binary0 Size: 0x100000
FAT0 Size: 0x4000000
FAT1 Size: 0x3340000
All Size: 0x7440000
FAT0_ADDR=0x100000,FAT1_ADDR=0x4100000
USB>task 28 55aa
Wait..
DOCInfoTableinitHW+
Binary0 Size: 0x100000
FAT0 Size: 0x4000000
FAT1 Size: 0x33C0000
All Size: 0x74C0000
FAT0_ADDR=0x100000,FAT1_ADDR=0x4100000
USB>set 14 0
HTCST ЪИТHTCEUSB>set 14 10
HTCSF kEШ(HTCEUSB>set 14 9
HTCSF kEШ(HTCEUSB>
DONT PANYC after NO BOOT-> REFLASH CEOS.nbf (HW6915 ROM FOR G4-121UK) FROM HP Utility.
Info for Pass1:
HTCSPass1.CM€ЛHTCEUSB>password 0000000000000000
Work?
sorry for BAD english
This procedure is free to use but at your own risk, I take no responsiblity for any conflict, fault, or damage caused by this flashing procedure.
hi
i had no bootloader
returning
Spgi, it really worked, but how can I go back with the previous ID?
all solve here :
1st
need: MTTY
steps
1: Bootloader
2: mtty
3: task 28 55aa (fully format device)
4: rtask 0 (reset radio)
5: Reflash device
Above from wiki XDA dev's
Important, do not try to start device after above, after radio reset, put device back to bootloader directly
If above does not help you need to reflow or reball radio chip (tested and working if above does not work)
And my result from MTTY:
task 32
USB>password BOOTLOADER
HTCSPass.< YHTCEUSB>info 8
DOCInfoTableinitHW+
Binary0 Size: 0x100000
FAT0 Size: 0x4000000
FAT1 Size: 0x3340000
All Size: 0x7440000
FAT0_ADDR=0x100000,FAT1_ADDR=0x4100000
USB>info 7
HTC Integrated Re-Flash Utility for bootloader Version:1.50a SABLE EVT version:G.39
MainBoardID = C
Built at: Jun 12 2006 13:46:04
Copyright (c) 1998-2005 High Tech Computer Corporation
Turbo Mode Frequency = 312 MHz
Run Mode Frequency = 208 MHz
Memory Frequency = 208 MHz
SDRAM Frequency = 104 MHz
USB>info 4
HTCS Lњ3ЖHTCE
USB>task 28
DOCInfoTableinitHW+
Binary0 Size: 0x100000
FAT0 Size: 0x4000000
FAT1 Size: 0x3340000
All Size: 0x7440000
FAT0_ADDR=0x100000,FAT1_ADDR=0x4100000
USB>task 28 55aa
Wait..
DOCInfoTableinitHW+
Binary0 Size: 0x100000
FAT0 Size: 0x4000000
FAT1 Size: 0x33C0000
All Size: 0x74C0000
FAT0_ADDR=0x100000,FAT1_ADDR=0x4100000
USB>set 14 0
HTCST ЪИТHTCEUSB>set 14 10
HTCSF kEШ(HTCEUSB>set 14 9
HTCSF kEШ(HTCEUSB>
DONT PANYC after NO BOOT-> REFLASH CEOS.nbf (HW6915 ROM FOR G4-121UK) FROM HP Utility.
Info for Pass1:
HTCSPass1.CM€ЛHTCEUSB>password 0000000000000000
source:
http://forum.xda-developers.com/showthread.php?t=471942
final steps
If your Flash chip type is G4, you can use ENG V1.21UK rom to update, I have uploaded the rom to Yahoo.com mail box.
I have changed my 6965 CHT ver to ENG ver successfully.
You can login yahoo mail box by using [email protected] as id and 69656965 as password.
Pls note not to delete the rom as others might need it too.
Flsah method:
1. Sync your mobil with PC by ActiveSync4.5 or up
2. Double click the downloaded update rom programme.
3. Click upgrade button and wait for 8-10 minutes
4. Done.
source
http://forum.xda-developers.com/showthread.php?t=420041
please, don't chage anything. keep data safe for other people
has anyone tried the above instructions and succeeded ? I have a perfectly working 6915, but it's in Spanish and I would like to change the language to English. I'm afraid of bricking the phone or end up with the "No GSM" problem.
DO NOT USE that way.Surely, your phone will become a brick. That will change Product ID with invalid code and you will never restore SW for radio ROM .
Morning all.
I'm trying to debug and restore a Mi TV stick that is stuck in a boot loop. It happened after I switched it on, its video got stuck in xiaomi logo, and after power cycling it never worked again.
The LED doesn't switch on and have no video signal on the hdmi, so I disassembled it and connected to its serial port pins and saw the following trace, in loop:
Code:
GXL:BL1:9ac50e:bb16dc;FEAT:BDFD71BC:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;0.0;CHK:5E6;READ:0;0.0;0.0;CHK:0;
TE: 444948
BL2 Built : 10:47:30, Jan 14 2019. gxl g152d217 - [email protected]
set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 7
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - FAIL
DDR3 chl: Rank0 @ 912MHz - FAIL
DDR3 chl: Rank0 16bit @ 912MHz - FAIL
DDR4 chl: Rank0+1 @ 912MHz - FAIL
DDR4 chl: Rank0 @ 912MHz
bist_test rank: 0 21 03 40 2b 12 44 1f 02 3d 32 1a 4a 20 00 40 2b 14 43 26 08 45 27 0d 41 660 - PASS
Rank0: 1024MB(auto)-2T-18
AddrBus test pass!
eMMC boot @ 1
sw8 s
emmc switch 3 ok
BL2: rpmb counter: 0x00000020
emmc switch 1 ok
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000, part: 1
aml log : R1024 check pass!
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01700000, size: 0x0000d600, part: 1
aml log : R1024 check pass!
Load bl31 from eMMC, src: 0x00020200, des: 0x01700000, size: 0x0002b400, part: 1
aml log : R1024 check pass!
aml log : SIG CHK : 231 for address 0x01700000
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000, part: 2
emmc switch 2 ok
I assume that perhaps when I power cycled it was updating and its emmc got corrupted?
Is their a way of reflashing the firmware on these devices? I've seen this post here at XDA but wasn't able to enter in USB mode as described. I was able to find the 2 pins but after shorting them nothing happens.
Any tips on how to recover this device?
Thank you!
Did you try to change the charger and/or the cable?