Himalaya I can't hear anything when Calling - MDA II, XDA II, 2060 General

Hello all
I have big problem with my himalaya. When someone calling to me or I calling to someone i can't hear anything and he can't hear me. But I can hear ring tone, mp3. I can hear someone and he can hear me when I connect my XDA 2 to computer.
What i can do with That??

the problem is with the connector.few Pins are broken or are touching each ither...which causes the Hima to go into Car Mode..try connecting a Headphone and see if it works or not..else get your Connector replaced

no audio
If the above doesn't work, this could be a problem, which after a LOT of research I don't believe there has been a fix found for. Essentially , my problem and a problem my mate had was that the audio on the phone was working FINE, MP3, ringtone etc... but upon answering or calling, there was no IN CALL sound. it WORKED with a headset, but no amount of fiddling with the jack sorted it out. THe LOUDSPEAKER also would NOT work.
Having a few donar phones lying about, I just put a new board into the phone and forgot about the problemed one for a week or so, left it laying in my drawer. Tried it in the phone after waiting this time, and it worked FINE.... the problem had rectified itself.
I know this isn't necessarily helpful, but perhaps leaving the phone in a dry warm place ? could be moisture..?
hope this helps.
..........IB a n e

well, it happend with me yesterday, just took the Batt. out ( 30 second), put it back, reset the device, and all will be OK,....its a software feature AND NOT A BUG... beleave it or NOT....
Salam

Related

JASJAR SOUND PROBLEM

Hi,
Am using a Jasjar. One fine morning the phone stopped ringing. No sound from the speakers at all. Though I could hear the other side on recieving or making calls. My voice does not go.
I sent it for repairs to I mate service center in Dubai (am in mumbai), Got back the machine working today.After making 5-6 calls ,the same problem has started again.
Please advice.
thanks ,
AT.
sounds like they didnt fix it, my 5.1 amp has just done similar, well not similar, but similar issue lol, grrrr
amp stopped doing video, sent to yamaha for repairs, got it back !!!AFTER 2 MONTHS WAITING!!! 2 weeks later its doing it again.
Back to Dubai it goes then! This time, try to shout enough so that they actually fix it. :lol:
A quick suggestion: (just in case)
In some cases people have had problems with sound loss from their Universals caused by the headphone jack. The sensor that identifies whether a headphone is plugged in is faulty and cuts out the speaker sound.
You could try putting a headphone jack into the socket and wiggling it, or plugging it in and out a few times. That might fix it.
I've had the same problem too a couple of times. I found that it was something weird with the battery actually. It always seemed to happen when I switched batteries. Everything would work fine except the audio. I could make a call but the other side couldn't hear me. When I would "click" on anything like Start all I would hear is a small popping sound. I found that if I took the battery back out, and then put it back in and made sure it was securely set in place & locked it the sound would work again. Sometimes I would have to do that twice before it would work again. I'm not sure if it really is a battery thing or something else that gets jiggled when I put a new battery in/out but that's what's worked for me. Hope that helps.

Strange sound issues (this is a tough problem!)

Hey all, im glad this site is up its been great finding what i can really do with my wizard!
here is he issue im having. the wizard has 3 different speakers and 1 microphone. 2 side speakers (used to play music, or speaker phone) and the 1 main speaker (used for hearing calls). none of the 3 work when im making calls, listening to music, alarms, or any of the "screen click" sounds and the microphone doesnt work on phone calls or note recordings. however, the one time the speakers do work is when i have an incoming call, i tried listening to see which speaker its coming out of and it sounds like all 3. the headphone jack still works so thats what ive been using. pressing the speaker phone button while on a call (that i cant hear) doesnt do anything, the UI doesnt show any change or switch to indicate its changed to speaker phone and the "speaker on" button doesnt change to "speaker off" like it used to.
originally i thought this was a ROM issue, i was using the manufacturer's ROM (cingular 8125, unlocked for tmobile service) so i followed the lovely tutorial and switched my phone over to the t-mobile 2.26 ROM. this had no effect, so I then upgraded to XDA's WM6 ROM and while i love this new ROM it still did not fix my sound issue.
im stumped, any help anyone can offer would be great. I wanted to post here before i crack it open to look at all the insides.
same problem!
I'm having the exact same problem! I just noticed the problem recently, when my phones alarm didn't sound. I'm running a custom cooked rom from mattk_r 318 kitchen, but I don't think the rom is the problem, as i am indeed still hearing sound from the head phone jack. I don't think the internal speakers are broken, as when a call comes, the phone rings, and the sound come out from the speaks as mentioned above!
Help!
dropped?
have you ever dropped your phone?
I have dropped mine a couple times and thats the only cause I can come up with. But this never seemed to be a problem until recently.
no major drop recently.
i havent really dropped it recently at all.and for some reason i dont think the hardware is the problem,because i tryed voice recorder,and it records my voice and i can play it
back through the headset.so that confirms that the mic and both spealers work (rings
when incoming call). i really dont want this to be the downfall for my wizard! is there
any key registry entrys for sound maybe that we could have a look at? btw my wizards a G4 if thats makes any difference.
please help!!
mine is a g3, if it were a software issue then reflashing should have solved it. right? i dont know enough about the internal workings of the wizard to know what a flash actually does.
?
Anyone have any ideas on what I can try?
Well, a flash is an OS upgrade/downgrade. It contains drivers, programs, registry settings, things of that sort. Sounds like your problem is hardware related, nothing to do with the OS itself.
I assume the warranty on that baby has already expired, so you're pretty much on your own.
Two options come to mind:
1. The obvious... buy another Wizard
2. The not so obvious... buy another Wizard with a broken screen and take all of its guts out and put them in yours.
A third option also exists... (ther's always a third way)
Mind you, this is for INFORMATION PURPOSES ONLY! In no way do I condone the below mentioned method.
Get a new line of service with Cingular and buy the Wizard to use with it. Exchange their boards, swap the IMEIs using the Wizard Service Tool utility found on these boards, cancel the line of service and return the "new" Wizard.
Sound issues
I have had a similar problem but located my problem to the microswitch which is in the headphone socket. Might be worth trying pulling the headphones in and out a few times to see if it allows the microswitch to release (if that is the problem?)
Steve
The wizard is magic
Some how my wizard seemed to repair it self. Its sound is working again...i didn't reflash or do anything special....weird. I think its because the phone had a good vibrate....ive got one of those speaker docks for the wizard..i put it in there...got a phone call and talked and stuff...but while it was in there (with the mic plugged it) it vibrated alot...maybe that flicked the switch mentioned above?
weird..this phone never ceases to amaze me. I just hope it doesn't happen again... because it appears to be emerging as a problem as the wizards get older?
Keep up the good work guys!
LOL!!!!!!!!! its so simple and yet so amazingly smart
wow, Steve you are the most amazing person EVER!
I put the headphone piece in about 1/10 of the way and slowly made a swirling action as i slid it all the way in, clicked the start button on wizard and i heard the "click" for the first time in a month!
Thanks!
I tried different options to get my sound back, no luck so far
Problem started after using the headset-connector to connect it to an FM-Transmitter.
After reading this thread, my guess is that the "micro-switch" is in a wrong position. So I opend my MDA, but can't find any "switch" in that connector.
Is there some more info about that connector, a connection-diagram perhaps ?
what worked for me was inserting the headset jack in roughly, robbing each side of the headset jack to try to hit the "switch". that might work for you.
Yes!!! Thank you a lot!
I have the same problem, no sound in my speakers, just vibrate and sound in handsfree. I figure out that this micro-switch could be the problem, but I haven't know how to solve it. Thank you once again, I love my SPV!! and this community.
Fixed!
Woohoo!
This problem just cropped up for me on the weekend.
Thankfully it wasn't long before I happened across this thread.
About a minute of persistent jiggling the microphone jack did the trick.
Thanks!

Can't hear conversation unless it's on speakerphone

So, my phone stopped working a few days ago. I've been running WM6 for quite some time now and I've even tried going back to Tmobile's ROM. Basically, when I receive/make a phone call, I can ONLY hear the person if I put them on speaker. They can hear me regardless, but I can't hear them. Pretty annoying.
Any ideas?
Heh! Quite a coincidence!!! I cannot hear anything from the headset either and it happened a short while after I upgraded to XDA6. It work fine with the stereo headset as well as with a BT one. The difference in my case is that I cannot switch to speakerphone. The phone is deaf without a hands-free device.
I have posted a separate thread on my problem - here it is
i have the same problem. phone is dead without a handsfree it happened to me last night all was good, i was listening to music to handsfree and removed them to make a call and it didnt work anymore..i reinstalled the rom, but no sound..any help anyone?
maybe the phone is stuck on handsfree..it things that the handsfree is plugged in or something?
problem solved trustworthy, i've put the jack in and out a few times..and now the sound works there is a switch that is pressed when you plug in the jack and maybe it got stuck on handsfree..try pressing it a few times..i don't know. now my phone works. i'll never plug in a handsfree again
I had the same problem--it was still under warranty...new MDA was the solution.
By the time it goes again I hope the next generation will be here!
I have the same problem as lilcam, the earspeaker is dead. I had the same problem once, and the service chage the speaker, first and the ringer, later and stars working just fine. Now, the silent speaker hits again and service says is not the same problem and they cant repar it. Does anybody have a clue?
Sisqo said:
problem solved trustworthy, i've put the jack in and out a few times..and now the sound works there is a switch that is pressed when you plug in the jack and maybe it got stuck on handsfree..try pressing it a few times..i don't know. now my phone works. i'll never plug in a handsfree again
Click to expand...
Click to collapse
Thanks for the hint, but I REPLACED the handfree jack and it still wouldn't work without the headset
The people, who got it serviced told me that there was a problem with the mmainboard, that they cannot deal with. As I've mentioned in my thread, they also told me that a faulty handsfree jack was a frequently occurring problem with the 9100. I would recommend to pdebeitia and Sisqo to try replacing the jack. Hopefully it might help...it did not work for me though...
BTW, pdebeitia and Sisqo, what ROM are your MDA's running or were runnig at the time when it happened?

MAJOR sound problem

Hi all,
yesterday, the following parts of my Uni stopped working properly:
- speakers
- phone speaker
- microphone
Not only was there no sound at all coming from the speakers, but when I made a phone call, I couldn't hear the other person and neither did they hear me. The phone was thus rendered pretty much useless. I didn't try it when making calls, but when I turned on music, it played without problems when I plugged in the headphones.
Reseting didn't help so I reflashed the unit.
Everything was fine wor a while, but then the problem occured again.
This time, reseting the device solves the problem, but only for a few minutes - then the sound stops working again. EDIT: oh and now I also discovered that it starts working again at some times for no obvious reason and goes back to not working in a short while *CONFUSED*
Does anyone have an idea what it could be caused by and how to solve it? Many thanks!
I had a similar problem earlier.Try putting ur headphone jack in and out a few times,this generally sorts out the problem.It has to do with a small pin in the headphone socket which diverts the sound to the headset when it is plugged in and the pin has to come back in position when the headset is disconnected.What happens is that the pin gets stuck,so even when u disconnect the headset,it still diverts the sound to headset mode.PM me for more details
Longlife said:
Hi all,
yesterday, the following parts of my Uni stopped working properly:
- speakers
- phone speaker
- microphone
Not only was there no sound at all coming from the speakers, but when I made a phone call, I couldn't hear the other person and neither did they hear me. The phone was thus rendered pretty much useless. I didn't try it when making calls, but when I turned on music, it played without problems when I plugged in the headphones.
Reseting didn't help so I reflashed the unit.
Everything was fine wor a while, but then the problem occured again.
This time, reseting the device solves the problem, but only for a few minutes - then the sound stops working again. EDIT: oh and now I also discovered that it starts working again at some times for no obvious reason and goes back to not working in a short while *CONFUSED*
Does anyone have an idea what it could be caused by and how to solve it? Many thanks!
Click to expand...
Click to collapse
try it with bluetooth, if all sounds work fine, then problem is with the receptacle for the headset jack.
Had this problem myself. Took phone apart and repaired.
GL
Thanks, I guess the problem really was in the headset/external switch. It acted like crazy, switching back and forth for no reason, but when I tapped the headphone jack hard with my finger, it usually got ok.
And for the past few hours, the sound worked perfectly, so it hopefully is ok again now. If the problem comes back, I guess I will take it to the service center and get it repaired - I don't think I'd have the courage to do it myself
Anyway, thanks a lot for your help guys.

Audio dies on my Uni... then is resurrected!

Yesterday, something strange happened... The speaker and microphone on my Universal stopped working - all of a sudden, out of hte blue, and completely inexplicably!
I spent 4 hours on a train yesterday, and was listening to music on my Uni nearly all the way through. I had also used it to make calls and it was working fine. Since I was using normal headphones rather than the bundled hands-free headset, making a call involved unplugging the headphones and holding the phone to my ear - so I know that, for at least part of the day, the phone's speaker and mic where working perfectly!
I kept on listening to music on my cans until the journey ended. I then check my phone and find 9 missed calls, from various people. "Strange," I thought, "I had the headphones on all the time - why didn't I hear it ring?"
I try to call back some of the people who had tried to get to me. As I watch "dialling..." switch to "connected", I hold the phone up to my ear and say "Hello...?" and hear nothing in return! I try again several times, with the same result. I try soft-resetting the phone a few times. I try switching from 3G to GPRS in case it was a radio problem. Nope, not a radio problem, as I can still send and receive texts. A few start coming in. They read "I CANT HEAR U! R U ALLRIGHT?" Great, so it's not just the speaker, it's the microphone too. I try making another call, but using speakerphone: doesn't work, and in fact won't even enter speakerphone mode! I press "Speakerphone on" on the touchscreen but it just doesn't want to go there - the speakerphone icon doesn't appear on the status bar, and the button doesn't change to "Spreakerphone off" as it should do.
I get home, do several more resets. No result. I try plugging in the headphones and playing an mp3 file. As I suspected: I can hear just fine through the 'phones, but when I try to unplug them to see if there would be music coming out through the phone's speakers as well, they stay mute.
Great, I thought, phone's busted! Well, still works... but not as a phone! Unless I permanently use some hands free solution. So, an unwieldy device just got more awkward to use!
I leave it disassembled (battery and sim card out) and put it in a drawer. I'm already thinking about new phones to buy when I go to sleep. The next morning, I decide I need to check my calendar, so I put my phone back together and switch it on. The battery had run down completely: it now thinks it's January 1st 2006. Happy days, I remember them: my phone worked back then. Then, all of a sudden, someone calls me and, oh joy of joys! It RINGS! I can HEAR it! It's 2006 again! I answer, casually have a conversation on a working phone, and hang up. Problem solved! Phone shopping averted!
The question is, why would this weirdness happen? The speaker and mic stopped working LITERALLY in the middle of using them! I was sure that they had gone, that it was a hardware problem and it would need repair or replacement, but no, it turns out it was some kind of software problem which leaving the phone off overnight fixed! Why would it break so suddenly, and why would just leaving it off fix it? Anyone vaguely tech-savvy want to hazard a guess?
If you use earphones, your 3.5 plug is simply shorted when you pulled the earphones out. What I suggest you do is start playing some music or sound files on your media player and insert a very fine thin screwdriver into the earphone plug then wiggle it lightly until the sound from your speakers comes back.
Yea i had same problem ... and as Enigma said it is due to some left over of 3.5 m jack....the phone still thinks the jack is plugged in, hence no sound from built in speakers.... just take a toothpick and wiggle it in the 3.5 m earphone socket or you can just blow it with some air.....

Categories

Resources