hey all,
I've been with the xda I from the very beginning and have always upgraded the roms to newer versions. However, a few months ago I was happy with my 2003 and didn't upgrade.
When TomTom stopped working I thought a nice new upgrade was in order and I cooked up a new rom and installed it. I played around with it, and I think (don't remember anymore) that I've touched the band tab.
Since then I have not been able to get a signal or find a network AT ALL. I have tried everything.
I couldn't install through the normal way anymore, so I resorted to SD-installing.
Spent days here with xda-tools, tried every rom version, even installed official radio stack again. Nothing helps. I have tried selecting the band at the wallaby menu. No go!!
I'm very afraid that I've messed it up.
I will boot into the OS, but no signal. With some roms it will give me the phone setup, with most it won't.
Right now I have the german t-mobile installed. It just says: no service.
Some (current) stats:
Wallaby bootloader 5.14
R 4.21.00
Protocol: 32S54
4.01.19 GER
Is my XDA I lost??
Some pointers would be great! I'm out of idea's.
Regards,
Ruurd
I've had this recently - the way around it is simple, assuming you know what band your network provider is on.
Go to the bootloader menu (soft reset and power button), and select the band on there. I had "no service" on Orange, until I selected "1800" on the menu that is, and hey presto, working phone!
I had tried that already, and it didn't work.
However, I just did it again (tried out all combinations) and yes, it did work!
pffeww!! :lol:
thnx
I recently bought an SD-502 receiver for my XDAII and have no end of trouble since. I was hesitant to buy it given the compatibility problems but latest compatibility lists say that it has been tested and works. Long story short, COM 7: which is supposed to be assigned to GPSUART as per GPS PPC websites is absent and I cannot find any way to add it. I have upgrade from WM2003 1.60 to 1.72 and there was no change.
Further to this, I have downloaded the WM2005 upgrade in the hope that It would recognize the device but now I can't load any version of WM withouth the Himaupgrad.exe saying that there was 'a problem during upgrade'.
Thanks to anyone who chooses to help.
Can you be more specific about this 'problem during upgrade'?
That's what Himaupgrad.exe calls it... verifies the ID of the pda and then you click yes to upgrade and it goes to the screen where it clears the current rom and loads the 3 new ones and instead of doing that, after about 30 secs it just says there was a problem during upgrade and says to soft start the pda, which I have tried with no success. I have tried many combinations of Radio, Ex Rom and Rom without luck. I have even tried the original upgrade package that is already on there which I downloaded from the UK o2 site and that gives the same error. So I figure it is something to do with the PDA not the upgrades.
Again, any help is much appreciated!
Thanks jamil
Hi all,
I recently took out my sim card to replace it with a new one. However, when i placed the new one in and turned the BA on i recieved no signal, furthermore, when i put the passcode in, it said it was wrong. of course, I have punched in the right code i have always been using.
i have tired hard reseting but it still doesnt work.
Are there any other options avaliable apart from flashing a rom in again?
Any help or suggestion will be appriciated.
Kind regards,
Jason
some help would be appriciated
jasonchiu said:
Hi all,
I recently took out my sim card to replace it with a new one. However, when i placed the new one in and turned the BA on i recieved no signal, furthermore, when i put the passcode in, it said it was wrong. of course, I have punched in the right code i have always been using.
i have tired hard reseting but it still doesnt work.
Are there any other options avaliable apart from flashing a rom in again?
Any help or suggestion will be appriciated.
Kind regards,
Jason
Click to expand...
Click to collapse
These are both known glitches in the BA with WM6
For the no signal a soft-reset should fix it, for some reason if you remove the battery and then replace, the first boot has no radio initialization, but a soft-reset after that fixes it.
As for the passcode, you have to clean your hive file to regain access to the device. You do not need to format storage, but all your registry settings for installed software will be gone. Most likely a re-install of each app will be needed.
i just went through this..i tried changing my sim card and i was freaked when i saw no radio rom installed..then i upgraded to radio 1.15 and first it worked but again i t showed the same so i went into bootloader an then soft-reset and its working till then ( about 5 softresets till now)
cheers guys, will try that out.
Hi guys i have just bought a HD2 from ebay. It was supposedly locked to o2 in the UK which was fine as thats my network and i thought it would save any problems.
This is the first phone of this kind i have bought so i was completly green when it came to the roms etc. Having read a bit it appears my phone is unlocked as i get the HTC splash screen when it starts and not the o2 screen.
I have also checked the spl and its 1.42.0000.
So ok im guessing it being unlocked shouldn't be a problem but the 'get location' and weather features won't work. When i try them i get a 'there was a connection error while trying to download weather data'.
Also when i view wireless Controls i cannot activate data connection and when i try i get 'The answering modem has disconnected' warning.
Does anyone have any idea what causes this and should i consider installing HSPL and a modded rom or is it possible to install an o2 stock rom and would this correct these issues ?
Thanks in advance Major ChAoS
Hard reset the phone, and let the phone install your wireless data settings.
Sounds like it's not setup for O2 properly.
Hello,
I've noticed something strange this past month. I was getting data disconnections and I could'nt figure out why. Each time I look at my phone, turning the screen on, mobile network (voice + data) is missing for a few seconds, and comes back.
Now I know that if I keep the screen on for a while (I tried more thant 1 hour), I don't loose the network, but if let the screen go to sleep I immediately loose the network (I don't receive whatsapp messages in background), and when I turn the screen on, it comes back.
Weirdly, when my phone could reach 4G, I had (almost) no disconnection. It only happens in a 3G, edge, or nodata zone.
I changed my carrier (I just moved from europe to New Zealand), and it doen't change the problem.
I'm using CM11-Nightly (sept) on a I9505. I tried installing an old nightly(from july), and it was really full of error messages, so I switched back to a recent nightly, but in the meantime I had no disconnection.
Thank you for your help
noisy_sha said:
Hello,
I've noticed something strange this past month. I was getting data disconnections and I could'nt figure out why. Each time I look at my phone, turning the screen on, mobile network (voice + data) is missing for a few seconds, and comes back.
Now I know that if I keep the screen on for a while (I tried more thant 1 hour), I don't loose the network, but if let the screen go to sleep I immediately loose the network (I don't receive whatsapp messages in background), and when I turn the screen on, it comes back.
Weirdly, when my phone could reach 4G, I had (almost) no disconnection. It only happens in a 3G, edge, or nodata zone.
I changed my carrier (I just moved from europe to New Zealand), and it doen't change the problem.
I'm using CM11-Nightly (sept) on a I9505. I tried installing an old nightly(from july), and it was really full of error messages, so I switched back to a recent nightly, but in the meantime I had no disconnection.
Thank you for your help
Click to expand...
Click to collapse
I don't know exactly where this option is, but it's for battery saving. You can choose that somewhere in your settings I think
I think that's true for Wi-Fi, but I never found it for network.
And now it seems that network won't come back if I don't go to airplane mode and back to normal mode.
I'm having the same problem, seems to mostly affect lollipop installs.
Did you find a solution?
Penetal said:
I'm having the same problem, seems to mostly affect lollipop installs.
Did you find a solution?
Click to expand...
Click to collapse
No I didn't. It seems that somewhere in july 2014, CM11 included a new version of the modem. So every CM11 build after that and every CM12 build is affected (I don't know about other roms).
I read that it was the way the modem handled finding the best network method. With the previous modem (v5 ?) it tried to get LTE, 3G, etc... but now it fails when it fails to get the prefered network.
4 solutions:
- flash the modem (didn't try it, don't know how)
- You're supposed to be able to choose you're prefered network in the options and choose 2G/edge. Didn't work for me but I'm interested in your feedback.
- get an old version of CM11
- live with it (my current option :'( )
There is maybe another solution, I'm not an expert, just a desperate user.
Hey again, I did fix it for myself.
The modem is the problem (I flashed my modem, and my bootloader just to be re-up-to-date).
If you want to get lollipop for yourself you should do it, its not too hard
Its listed as Qustion 14 on this here page: http://forum.xda-developers.com/showthread.php?t=2419762
I don't mind trying to give some pointers if you need help understanding how to do it, but I did this at 5am while sick so my memory of what I did is not 100%, never the less I would like to help if you need it.
Thank you for the advice (you came seeking for one, and ended up helping me ).
How did you choose which modem version to pick up ? the latest ? Do you have to do it after every CM upgrade ?
Edit:
I found the latest version from one of your links : http://forum.xda-developers.com/showthread.php?p=50965837#post50965837
Is the "Combined package - both modems in one flashable file." ok ?
And what does flashing the bootloader do ?
"What it does"... I am not 100%, I assume it initialize some part of the system, HW or kernel level, but I might be way off.
In any case I did use the dual modem pack to flash both "PHONE" and "PDA", another thread I asked in just replied to another user with the neccessity to flash the new bootloader aswell (dont know if the version numbers applies for you):
u must be using a 4.4.2 baseband and bootloader .. just a 4.4.2 baseband will not work .. once updated ur set
Click to expand...
Click to collapse
My question is on this page a bit down, and some replies a bit further down than that:
http://forum.xda-developers.com/showthread.php?t=2735248&page=116
Tip: I had to save the PIT to a file (did it twice to be sure) with heimdall before using odin to flash (couldn't get heimdall to work for that part), all because odin would not play nice inbetween loading the PIT from device and flashing, this might not be a problem for you at all so it's just an FYI.
I managed to flash the modem & the bootloader. So far, no disconnection, so I'm quite happy.
Cheers