In first, i'm sorry for my bad english.
I have my trinity since one year, and since 2 weeks i can't charge it. When i connect my phone with usb cable, the red led light but blink, and the phone show 100% charge. But when i disconnect it, battery isn't full. I bought a new battery but the problem is the same. I thinck, i'm going to buy an external charger for my both battery. But before i want to know if anybody have the same problem and perhaps a solution.
Related
Is there a wizard who can find a solution for my wizard !! I bought it one week ago now i have got black screen with no ability to turn the phone on and also no ability to soft or hard reset everything is dead and there s no battery charge ability. Any solution to slve it Please HELP ME !!!
Are you trying to charge the battery from the computers usb (or a 3'rd party usb wall adapter?) if so, this will not charge a completely dead battery. Try plugging it in to the usb wall charger that came with the device. This may help to charge the battery. Let me know if it works, or if you have any other questions....
You may need external charging
Charging of these batteries is controled by in-built circuit, so when it is discharged extremely low, it is very difficult to start charging.
Try leaving on charge for several hours or days and see if it starts charging. If it fails and you have no option to return it or buy replacement immediately, you may try to locate the polarity and use an external charger of same spec as reccommended for a few minutes and then continue charging in the wizard.
Someone did it here on the forum. You may want to search :roll:
Victor
Hello,
I bought a second hand Qtek 2020. The seller didn't have a cradle, but he gave me a USB sync/charge cable and a AC plug with USB slot. So I insert the one end of the cable to the PDA, one end to the plug and I recharge.
The device came with 90% charge and I could easily charge it to 100%. Today, I ran it down to 0% and now I can't recharge it!! Every time I turn the device off and plug everything in, it starts to recharge. The led on top shows red. It charges for about a minute and the device wakes up. The red light turns yellow. It says on the screen that the device is still charging but the meter is stuck at 0%!!!
I've been trying for hours but I can't even get to 1%. Maybe it would be better if I had a cradle but that's not an option now. Besides, it recharged beatifully yesterday.
I have a feeling that if I can stop the device from waking up automatically when charging, I can recharge fully, but I don't know how.
Any help will be very appreciated.
Update
Here's a quick update. It's gone from bad to worse. Now I only have a blinking red light and the device doesn't come on at all!!
Any advice please?
Have you made sure that the plug is connected tightly to the PPC? If the charge isn't being held, then the battery might be the culprit.
li-ion batts have a limited number of times it can be recharged before it's lifespan is over
maybe your batt's time is up ?
Follow-up
OK. I bought a new battery and everything works fine now. So if you're having a similar situation, a new battery may solve your problem too.
same problem
I had the same problem as you. When the battery was on 30% to 90% it could be easily charged via USB from PC or via usb adapter. Once the battery fall under appr. 20% I was unable to charge it. I wanted to throw to the garbage. I have done many upgrades many resets. While the qtek was without any software (nothing was installed on it) tha battery successfully charged. So used the qtek as ussual and tried to charge it before 20%. BUt now it fall again under 20% and it's happening the same, I can't charge it. The other strange think is, that I have tried 5 computers with USB.1 and USB.2 but is didn't help. Only one computer can charget from 0% to 100% and this one is in my work.. very strange and don't know what couse this... Normaly the battery holds power for two and half days, so don't wan't to buy new one now. If anyone has any explanation why it can be charge only with "one computer" or what can that couse, I really appreciate it.
Thank you
Hello!
i have universal the orignal battery dies very quickly shows wrong information !
i bough a new one i didnt use it for few months the battery was dead!
now when i charge it its keeps blinking quickly the red light !
dosent charge :S
any reason
Thx
I've got exactly the same problem, even when I plug it into the AC adapter. When I plug it in the AC it starts-up, but gives me the information that there's unkown battery left? How could this happen, I've used the thing with a new battery for about 4 days and then I let it rest for about 4 weeks but now it's dead!
Hi.I received a xda min s in monday and after a day of use the battery is discharged so I charged the phone with computer's usb port and the charging led is switched on. When I came back I tried to turn on the phone but it seems dead ... It is on just a few times and went off immediately after the first screen.
Anyone can help me ? Thanks
Hi,
Just been through the same with mine. Thought it was the battery, so got a new one via ebay. Had the same problem, long story short, it turned out to be the usb cable, changed it and new battery charging fine. Looks like the old battery was fried as will not accept a charge any longer. The cable fault was rapidly discharging the battery, even though it indicated it was being charged. Hope that helps.
In first, i'm sorry for my bad english.
I have my trinity since one year, and since 2 weeks i can't charge it. When i connect my phone with usb cable, the red led light but blink, and the phone show 100% charge. But when i disconnect it, battery isn't full. I bought a new battery but the problem is the same. I thinck, i'm going to buy an external charger for my both battery. But before i want to know if anybody have the same problem and perhaps a solution.