I work at a University that has so many areas where there is no reception. However, it only seems to effect Telus and Bell Mobility phones (who share the same towers in Canada). Coworkers who are on Rogers and Fido wireless phones have strong strength everywhere.
Is the anything that can be done by Telus to install signal boosters to give reception to its users? Since there are probably thousands of people who experience this problem here, should they install whatever is needed to fix this. Could be a safety issue if someone needs to call 911?
I don't think it would be a safety issue.
Here in the UK, I had a similar phone with no signal when I was with Orange. Despite having no phone signal, I could still make calls to the emergency services. I presume there is an agreement in place that any emergency calls will just use any signal it will get
Above post is true.
You don't even need a SIM card to make an emergency call.
Well basic question...
How many different dial Menus do we have ?
##PROGRAM
SPC is 000000
Also had Radio items here
*#*#4636#*#*
Radio Menu
*#06#
Display IMEI
Some of the Options Explained:
WCDMA preferred - The GSM phone is capable of using both 2G and 3G data communication and when signal strength is low 3G is favored more.
GSM only - The GSM phone is capable of using only 2G data communication. When the 2G signal is too low you get nothing at all.
WCDMA only - The GSM phone is capable of using only 3G data communication. When the 3G signal is too low you get nothing at all.
GSM auto (PRL) - The GSM phone is capable of using both 2G and 3G data communication and when signal strength is low 2G is favored more. This one is a bit confusing to me since PRL is associated mostly with CDMA technology and not GSM technology.
CDMA auto (PRL) - The CDMA phone is capable of using both 2G and 3G data communication and when signal strength is low 2G is favored more.
CDMA only - The CDMA phone is capable of using only 2G data communication. When the 2G signal is too low you get nothing at all.
EvDo only - The CDMA phone is capable of using only 3G data communication. When the 3G signal is too low you get nothing at all.
GSM/CDMA auto (PRL) - Some phones are equipped with both GSM and CDMA capabilities. This setting appears to just have the phone attempt to stay connected to the data communication type that works the best. (Maybe the Samsung Galaxy S will take advantage of this???)
Unknown - If none of the above fit or the phone is acting weird as far as connecting to the carrier, you will see your preferred network type is set to this
Information has be sourced and pieced together from around the Web.
And seems to hold true on our devices.
I live in the UK (GSM) and have poor signal where I live. GSM phones can camp on to other operator's networks when the registered network is unavailable. There is also a 'scanning mode' to try and register on available networks (intended for manually connecting to a roaming partner).
So, has anyone come across an app that can report the signal level on ANY GSM network (even not the operator you are with or one of their roaming partners). I don;t mind if I have to disconnect from my normal operator when I run a test to get the other signal levels.
This would be good when trying to select what operator to move to (one with a better signal)
Hi everyone,
I already looked for an answer in the forum but nothing conclusive.
My moto g4 play loses signal during calls. The sim card is 3G and so I changed the network manually to 3g on the phone. However the problem continues and I think it even got worse. It happens especially when I'm moving, in the car, etc.
Is there any real solution for this problem? I have seen many users complaining but I did not realize if there was a solution or not.
Can you help me?
Thank you
Since the SIM is 3G, I'm going to assume the network you're using is GSM (ATT/Tmo). It is possible that the cell towers in your area operate on a specific type of GSM frequency, and your signal loss is due to the phone trying to connect to towers not supported by your carrier. If a call drops again, check the Roaming status of your phone in Settings and see what turns up.
Also, it seems odd that you would have to change the network settings at all. Even if the phone is set to prioritize LTE, it should automatically detect the 3G signal and adjust accordingly.
I have been using jio 4g for past 2yrs. The internet connection was good. But for the past 6 months I am facing frequent disconnection of the internet. So I go into flight mode activate and deactivate it again the net connection will be good for a minute and then it drops again to b/S. Frustrated I changed the SIM. But same problem. The bio customer care says it to update firmware! Which was not available and at last they told me to get the mobile serviced. So I swapped the SIM to another mobile and checked. There was no problem in that mobile. Please help me. Whether it is due to SIM or the band problem with mobile. I am using a stock firmware
Ps. Even I resetted, rooted
Set the network type or RAT or network mode to LTE (4G) only, then the phone should stay on the signal even when the signal is low for a second, around -120 rsrp (signal), specifically it should normally follow the parameters sent by the network: qRxLevMin (it is half the rsrp), qQualMin (sometimes, it is the signal quality), sNonIntraSearch, ThreshServingLow (both are ranges around qrxlevmin, one for entry threshservinghigh, one for exit). These parameters should nornally not be followed with LTE (4G) only. But only if the signal drops below the limit for a second. Else, it is a waste of resources, both for you (battery, etc), and the network, though the network can deprioritize cell edge (low signal) users.
To do so, there are extended network modes (for sim 1) in a menu that comes with Android, it is called 4636, Testing, Phone info, Device info, etc. There are apps that open 4636 without root, that offer: mode selections, lte only, anything cellular related that opens 4636.
Hold the phone on its top, not its bottom, for testing, the primary reception antenna should be at the bottom for A 2016, you can check this in *#0011#, it is "ant rsrp diff", it is positive when the primary reception antenna is better, negative when the diversity reception antenna is better, the diversity antenna should in most cases power on when the cellular is in use and start measurement, in contrast to the primary that's just switched on.
The signal can be measured in *#0011#, rssi is the signal strength of the frequency, the signal strength of intra freq (same frequency) neighbors (other cell towers etc) may differ slightly anyway because it's missing a decimal point; rsrp (good maybe at least -120, get it closer to -1) is approximately the signal strength of the cell, it is a few antennas in the long rectangular boxes on a cell tower, note that it is the measurement of the reference signal not the data that is being sent to your phone; rsrq(good maybe at least -15, best -1), sinr (good maybe at least 0, best 40), are signal quality. The "registered plmn" is the currently connected operator (mobile country code and mobile network code), if it changes (different compared to the sim), the signal is low! The "PCI" is the currently connected cell, note that there are only ~500 of these, so to identify the cell you can use both PCI and TAC (region), if the pci changes and the signal strength drops, well, the signal dropped and a reselection is made to an inferior cell, which can then drop data... in this case contact your mobile network operator but they might not make changes if it only affects a few users. You may try to lock band/etc to the good cell that sometimes drops in quality for a second but overall better than the neighbour cells.
Here's a short list of scenarios that can cause problems in connectivity, not all.
1: Low signal, plain old low signal. If the phone can't register VoLTE the bands that can be connected to may be restricted on some MNOs.
2. The antenna is closed and this causes low signal.
3. Low signal of the serving cell, the signal of an inferior neighbour cell matches (above parameters!), the phone changes to another antenna on a cell tower, quality drops and so does the connection. On another cell tower or there are 2 antennas on 1 cell tower, for example 1 facing the azimuth 180 degrees, another 270, the phone being in 215 degrees is unfortunate!
4. The antenna is open and receives interference (and reselections, sometimes good) from neighbour cells.
5. Good signal but it has been echoed a bit too much.
6. Reject causes and others, where the connection has been disconnected for some reason. Probably not in this case! It is viewable in *#9900# > Take cp log > copy to internal sdcard. It is in the /internal storage/log/LitmusLog. Scroll down to the reject cause section, those are error codes.
None of these codes/volte are working: The CSC is not applied correctly! Flash stock rom and open the stock recovery or copy /system/csc/...csc.../system/ to /system/etc/.
I do not recommend anything EFS/PIT, making a backup of efs is OK!
Hi,
I am facing the same problem with a7 2016 with JIO sim.
The mobile is purchased in dubai and when insert jio sim in india, was not able to use volte service.
So I flashed official indian rom. Everything is fine except net speed. Net speed between 1-5am is very fine but in day time speed reduces.
Everytime i have to restart data to use net but after a while same problem occurs.
Tried in both sim trays. I am using single sim in mobile.
Pls provide a solution.
Regards
//aftab