hello guys,
i need an help to configure AS & BT. Do you know a good guide
that could help me? Because when I try to sync from my HTC3600
with AS through BT I get an error message in Italian that states that
there is no partnership to a PC that supports BT. The problem that I have
already set up a partnership with definition of the serial port.
I guess it is a bit difficult to explain, but who has already had such
a problem could understand.
Please, let me know your experience. Regards.
These are instructions I developed for someone with a T-mobile MDA (Wizard G4) ...the USB sync was non-functional
NOTE: You must first install Microsoft ActiveSync on your computer…it can be downloaded here:
http://www.microsoft.com/windowsmobile/activesync/activesync45.mspx
(1) Enable the Bluetooth radio on your computer.
(2) Open ActiveSync on your computer…Start, Programs, ActiveSync.
(3) Select File from the menu and then select “Connection Settings.”
(4) Check the box that says: “Allow connections to one of the following:”
(5) Record the COM ports listed in the drop down menu (e.g., COM1, COM3, COM6, COM7, COM10) up to COM20.
(6) Select one of the COM ports (COM7 worked for me on this device…COM6 would cause ActiveSync to try to connect, but it couldn’t connect!?!?)
(7) On your T-mobile MDA Cell phone:
a. Go to Start, select Settings, and then go to the Connections tab
b. Tap on Bluetooth.
c. On the Mode tab check both boxes (Turn on Radio…, and Make this device discoverable….”
d. Tap on the Devices tab…select New Partnership…your computer should appear in the window.
e. Tap on the name of your computer to highlight it and select Next…
f. You may need to enter a Passkey (depending on the settings)…enter “0000” (i.e., enter 4-zero’s) and hit Next.
g. You may also have to enter the 4-zero’s on your computer.
h. The Select Services window should appear…check the box that says “ActiveSync” and then tap on Finish.
i. If you do NOT see ActiveSync you CANNOT proceed
ii. If you do NOT see ActiveSync as an option then select the Refresh option.
iii. Close all windows on your MDA.
(8) On your T-mobile MDA Cell phone
a. Go to Start, select Programs, and open the ActiveSync program.
b. Tap on Menu and then select Connect via Bluetooth.
c. ActiveSync should open and connect with your device.
Troubleshooting:
(a) If you get an error message that no device is set up, and the MDA asks if you want to set up a device, select Okay.
i. It will bring you back to the Bluetooth program & the Select Services window.
ii. If you do not see ActiveSync as an option go to the COM Ports tab and tap on New Outgoing Port.
iii. Your computer should be highlighted in the Select Device window.
iv. Click Next.
v. You will see a drop down menu with some COM ports listed…record these ports (e.g., COM6 & COM7)
vi. Make sure the COM port you selected in Step 6 above is shown in this list…select the same port (e.g., COM7).
(b) It has been my experience that the two keys are:
i. Step 7h …keep trying to “Refresh” until you see ActiveSync as an option (i.e., establish & then delete partnerships, and re-establish partnerships until it appears).
ii. Step 9a-vi …mess around with the combination of COM ports until it matches.
iii. Be sure that the port you’re trying to install in Steps 4, 5 & 6 are associated with your Bluetooth device…go to the Control Panel and examine your Bluetooth COM ports.
(c) NOTE: You do NOT need to establish the partnership from the computer side…it is ALL done from the MDA side!
Related
I guess I found a way to make AS 4.1 work offline!
After having numerous problems getting AS4.1 to work, I read somewhere on this forum that after you connect it to your network at work it will work like a charm. Indeed id did, even after I disconected from the network.
But today, I had to hard reset my JJ and AS4.1 did no longer sync! Just notes where synched. Well here is what I found out:
A) WM5.0 connects through a meager TCP/IP connection!
- Open your connection settings and search for Local Area Connection 3 (or 4)
- Go to properties and disable QoS Packet Scheduler
- Select the "show icon on tray" option
B) Open ActiveSync ande DELETE previous partnerships (Delete All)
- Open Connection Settings and select the following options:
- Show Status on Icon bar [X]
- Allow USB Connections [X]
- Allow connections to on....[COM3]
- This Computer connects to: [Work Network]
- Open ActiveSync when device connects [X]
C) Finnaly go to outlook 2003 and UNSELECT the Work Offline Feature
Connect your device!
It should synch perfectly OFFLINE! On dec 5th I'll check the settings to connect on the network and will update this post.
Can anyone please verify if this acctually works. ?
Cheers
Hello 4 all, my firs post
Its for BT version 1.2
In PC trey BT icon push right butom > BT setup wiz. > "I want to find ..." > "Next" (beefore on HTC Wizard: turn ON BT , in BT settings make discoverable to other devices & erase old conections with devices "PC") > take "BT device " > "Next" > Pin code "..." > Initiate Paring > ... > enable ActiveS (Com20) > Finish > on HTC active AS & Dialup "Finish" > open ActiveS > Connection set. > Allow con. to "com20" (not allow USB) "OK" > On HTC disabled BT > On HTC "Comm Menag." push ActiveS > menu > con. via BT > Yes > COM ports > New Outgoing port > "PC" > > com7 > finish > device > take PC > "ok" > go go go
if not conected, try again after 10 sec. ">menu > con. via BT"
It`s working 99%<[/b]
i do it and nothing ...
Why incoming 7... it´s on local services or client aplication ?¿?
and i don´t show on the ppc the activesync services of the pc ?¿?
miguelromerom said:
i do it and nothing ...
Why incoming 7... it´s on local services or client aplication ?¿?
New Outgoing port !!!!
and i don´t show on the ppc the activesync services of the pc ?¿?
Click to expand...
Click to collapse
In PC trey BT icon push right butom > > BT setup wiz. > "I want to find ..." > "Next" (beefore on HTC Wizard: turn ON BT , in BT settings make discoverable to other devices & erase old conections with devices "PC") > take "BT device " > "Next" > Pin code "..." > Initiate Paring > what u see in "BT service selection"?
I have: ActiveS; Dial-up; OBEX ...; Voice Get.
I install AciveS and then BT soft.
[/b]
YES I´VE the same on the pc, but the ppc don´t dectect the AS service over PC
miguelromerom said:
YES I´VE the same on the pc, but the ppc don´t dectect the AS service over PC
Click to expand...
Click to collapse
Which moment U don't see:
On HTC disabled BT > On HTC push ActiveS > con. via BT > Yes > COM ports > New Outgoing port > "PC" > NEXT > com7 > finish > device > take PC >
take pc ?¿? why port 7
regards
miguelromerom said:
take pc ?¿? why port 7
regards
Click to expand...
Click to collapse
One moment, I need to try one idea!!!
ok thanks
miguelromerom said:
ok thanks
Click to expand...
Click to collapse
1)On HTC BT setings delete device "PC"
2)on PC in Windows Explorer unpair your device "HTC"
3)read my 1 post and try it! I liltle bit change it & try 3time, all works
Good luck
THANKS OF NEW BUT NOTHING
I HR the pda and reinstall AS and BT SW
Thanks
I'm not sure what i did but it works - that's all what counts
By the way - what is BT soft ?
mine is widcomm
regards
did you use comport 20 for you activesync connection?
no i haven´t got 20 port available ...
thanks of new
I think I've got it
But it's a little tricky
1. Delete all connections on Pc and PPC
2. Start the Setup-Assistent and choose I want to find
3. Initiate Paaring
4. Choose ActiveSync without secure connection.
5. Set com20 if possible.
6. Please go to your ppc properties on your pc and allow active sync
If you coose com20 you can quit here, if not try this:
7. Start->Run->Regedit
8. HKEY_CURRENT_USER\Software\WIDCOMM\BtConfig\Services\
9. Search the folder with Name=ActiveSync (I have 0010)
10. Change the ComPortNumber to 20.
11. Search with your PPC the services on your pc and take activesync
12. Go to the preferences of your bluetooth-enviroment of your pc and take the tab local services. Now change the com-port number of your activesync service to an existing one (I have 4).
Now it should work
km
What if my computer does not show Activesync as a bluetooth option. I can get PIM synchronization but no Activesync. How do I go about adding Activesync as a service my computer can use?
I think the Activesync service is nothing else then a serielle connection called "ActiveSync" with com-port 20. Just create this on manually.
i think tomorrow we have a new rom version, a uninstall AS, and HR to the ppc, then i do this test...
thanks
I have the same problem, when I try to connect from the PPC it says there's no partnership with an AS enabled PC. And when pairing / updating services, the PPC sees serial and handsfree services on the PC, but no AS. Partnership is established, it works fine over USB.
Like miguelromerom I also use the Widcomm stack. Mine is urrently version 5.0.1.1400. I tried several older versions as well.
On the PC I have an incoming bluetooth serial port at COM 4, which is named "My ActiveSync". Secure connection not checked. AS 4.1 is set to allow connections on COM 4. The service on the PC is active.
On the PPC I had optionally configured serial ports: incoming (7), and outgoing (6) to the PC. Set the non secure. Though I'm not sure if either of them is required. I suppose we're all agreeing the port numbers on the PPC bear no relation to the port numbers on the PC?
km said:
7. Start->Run->Regedit
8. HKEY_CURRENT_USER\Software\WIDCOMM\BtConfig\Services\
9. Search the folder with Name=ActiveSync (I have 0010)
10. Change the ComPortNumber to 20.
......
12. Go to the preferences of your bluetooth-enviroment of your pc and take the tab local services. Now change the com-port number of your activesync service to an existing one (I have 4).
Click to expand...
Click to collapse
I also tried this. I still see no AS service from the PPC when doing this. It is not possible to select COM20 in the AS 4.1 connection settings.
Eric
ActiveSync via Bluetooth
I am not sure how it will go with Wizard, but with Magician it help me.
I found this step, but I forgot the origin. So actually no permission from the author. I share this with hope can help others. Hopefully the author understand.
-----
1)On your PC go to the Control Panel and select "Bluetooth". In the "Options" tab, make sure all the ticks are on. You'll now see a little bluetooth icon on your system tray. Makes it easier to access in the future. Your PC should also be ready to be found as long as you ticked the fist box in the step above.
2)On your Jam, Go to Start, Settings, System (Tab), Bluetooth Settings. On the screen that comes up you ONLY want to hit start. Leave the incoming and outgoing checkboxes OFF!!!
3)You will now be taken to the partnership screen, where you just follow the instructions to add your PC. Follow through until you hit finish. Close everything down until you're back at the today screen.
4)Back to your PC, double click on the Bluetooth icon in your system tray. Go to "Com Ports" (Tab) and click "Add". Choose incoming. A You'll see an incoming port added to the list (probably be the only item there). It should look like "COM X Incoming"
Remember what number is after COM. Close all windows, making sure you hit OK or Apply where you have to.
5)Open Active Sync on your PC. Hit File, Connection Settings. Enable the first tick, and select the COM port you had to remember in the previous step. Hit OK
6)Open Active Sync on your Jam. Choose Tools, Connect Via Bluetooth.
-----
Regards,
Arto.
Hey guys, anyone have an idea how to activesync over wifi with the prophet? I know activesync 4.1, which came in the box, does not support this, so i tried downgrading to 3.8, but activesync 3.8 wont recognize the device even through USB.
Any clues?
WM5 won't work with ActiveSync 3.x; it requires 4.x, which, as you've found out, doesn't support sync over WiFi.
Found this on Modaco if it will help.
1. Enter Network Connections
2. Create a new connection
3. Select 'Set up an advanced connection', click next
4. Select 'Accept incoming connections', click next
5. Click next on 'connection devices' screen
6. Check 'Allow incoming VPN connections', click next
7. Select all users which will be using this account
PPC settings:
1. Go to Settings/Connections/Connections
2. Select 'ADD A NEW VPN SERVER CONNECTION'
3. Enter the IP Address of your PC or its network name, select IPSec/L2TP and click next
4. Choose 'A pre-shared key' and enter some number combination (ex: 123456)
5. Enter user and password of desktop computer.
6. You're finished, enjoy!
Note: in case you have a firewall installed on the computer, you will need to change Activesync rules in firewall settings to allow connections to all IP addresses to default 169.254.2.2 address.
Pay attention that your PPC is setup as MY ISP/Work in CONNECTION settings.
it keeps returning "vpn server problems. verify your username etc..."
I'm trying this with an ad hoc connection. Could that be it? i know my username is fine...
Great, got it set up. Now how do I get activesync on my ppc to connect to the pc over the vpn?
Dudes
I wouldn't bother with this. As far as i can remember from the modaco thread no one got this to work!
XDA forum is different. Here the impossible can become possible, if some of the great minds here put their minds to it...
Cheers!
I've searched through the forums and haven't found anything regarding this specifically... does anyone know if we can use the Prophet (I have JAMin) as a GPRS modem? I used to use my Smartphone for this and would really like to use my new Prophet, but can't figure it out. The only time my laptop recognizes the hand-set as a modem is through Bluetooth and even at that doesn't allow a connection through Dial-up networking.
I would like to connect through USB... or by any means for that matter at this point! Help!
Yes, you can use the Jamin as a GPRS modem.
Instructions for setting this up thru USB and BT are at the bottom of the page.
http://www.imate.com/t-DEVICEMANUAL_JAMMIN.aspx
Please could you post the details as I can't see the site due to not being registered.
I own a Prophet too, but not a Jamin. Would love to know how to use it as a modem.
Thanks!
Pretty much copied word for word from the iMate document. However, I did do some editing as the original doc referenced screen shots that obviously aren't here.
1. From your PC's Windows desktop, double-click on the Bluetooth icon within the System Tray (Bottom Right Hand Corner of the screen).
2. This will open the Bluetooth Devices screen. Click on the Options Tab and tick the ‘Turn discovery on’ checkbox.
3. Tap on the COM Ports Tab and click the ‘Add’ button.
4. Select the Incoming COM Ports Tab and click the ‘OK’ button.
5. Click the ‘OK’ button.
6. On the PC’s System Tray in the bottom righ hand corner of the screen, right click on theActiveSync icon and select the ‘Connection Settings’ option from the pop-up menu.
Click the ‘OK’ button to conclude the COM port configuration for Bluetooth ActiveSync.
Uncheck the ‘Allow USB Connections’ checkbox and tick the ‘Allow connections to one of the following:’
From the dropdown list, select the appropriate COM port relevant to your PC, as shown in step 5 above.
Click the ‘OK’ button to conclude the COM port configuration for Bluetooth ActiveSync.
7. On the JAMin, the Bluetooth ActiveSync connection pairing attempt is made by the following steps.
A) Tap on the Comm. Manager icon in the bottom right hand corner of the Today screen.
B) Tap on the Bluetooth icon and select ‘Bluetooth Settings…’
C) Tick the checkboxes.
D) Tap on ‘New Partnership…’
E) Select the appropriate BT device from the list, then tap Next.
F) Enter the Passkey.
8. On the PC, a balloon appears above the System Tray, prompting the user to authorize the PDA’s Bluetooth access attempt. Tap on the balloon and then enter the same Passkey/PIN as was input into the device and press the Next button is clicked. A confirmation of completion screen will then appear.
9. On the JAMin, the ActiveSync Service needs to be confirmed by ensuring the check box is ticked and then tap Finish. (I don't remember if you need to manually start ActiveSync via BT after this. If you do, just open ActiveSync on the JAMin, tap on Menu then select ‘Connect via Bluetooth’)
10. Once the Bluetooth ActiveSync link has been established, the final phase of configuration is required. On the PC, you should get a Synchronization Setup Wizard window. Press the Next button.
11. Choose the relevant options that need to be synchronized between the device and PC, from the list, and then click the next button.
12. The ActiveSync Settings are saved.
13. Synchronization of the appropriate information types then occurs with the Exchange Server and PC as defined in step 11 above.
14. Click Finish.
for the ppc to detected as a modem you have to start the modem link. make sure you do not have active sync usb enabled. then with the disk in the drive of the pc enable the modem link. the pc will detect new hardware. then install the drivers from the cd rom.
Driver installation is driving me crazy!
I hope that someone can help me out because my problem is driving me nuts!
I have all the drivers on a CD as well as stored locally (unpacked, etc). Now, when I activate the modem link and the Laptop finds a new hardware, I am not able to install this driver (it says the device is unknown, while it should say HTC Modem (or something like this)).
So, I guess the problem is that the laptop does not know which drivers it should install. How can I install the driver without going through the setup wizard??
Any ideas?? It really seems a very simple process and I feel I shouldnt get stuck on this very first step.
Thank you for any advice!
This website have a good instruction on how to setup our prophet (WM5) as a modem. I sucessfully setup it yesterday.
http://www.pdagold.com/articles/detail.asp?a=269
whyhon said:
This website have a good instruction on how to setup our prophet (WM5) as a modem. I sucessfully setup it yesterday.
http://www.pdagold.com/articles/detail.asp?a=269
Click to expand...
Click to collapse
thanks whyhon, these were the instructions I followed. Everything is ok now (the modem mystrially installed after a few attempts) and the laptop is now hooked up to the s200.
The last problem I am facing right now is that I can not connect to the internet. I have tried quite a lot of different settings but I am not able establish an internet connection.
What else could I be doing wrong?
Are you dialling to GPRS using the USBModem_Dialer.exe?
Try using window XP build in dialer.
Start> connect to > HTC USB Modem (WirelessModem)
>Click properties
In the option tab, check "promtp for name and password"
Then dial using your operation's name & password.
Make sure you enable the Modem Link (USB) in your WM5.
Suprisingly, i able to connect at 230.8kbs using my Prophet.
whyhon said:
Are you dialling to GPRS using the USBModem_Dialer.exe?
Try using window XP build in dialer.
Start> connect to > HTC USB Modem (WirelessModem)
>Click properties
In the option tab, check "promtp for name and password"
Then dial using your operation's name & password.
Make sure you enable the Modem Link (USB) in your WM5.
Suprisingly, i able to connect at 230.8kbs using my Prophet.
Click to expand...
Click to collapse
thanks whyhon! I have tried to connect this way or with a dialer.exe.
The problem is that I am able to connect the prophet to the laptop (230.4kbps) successfully but I am not able to open any internet sites. When I check the connection I see that I am sending packages (or data I guess) but I am not able to receive anything.
I have tried a lot of settings and followed instructions very thoroughly but I can not get this connection working for the life of me.
I am about to give up on this one.
Would I be able to simply dial to a connection like AOL by using airtime minutes? Or is that also a mayor task?
Any help is highly appreciated!
Thank yoU!
No one has an answer to this one?? Sitting at SF airport and would like to use internet via laptop rather prophet... Please perhaps anyone can suggest a remedy? It seems to be working fine for other people so it must be something simple to fix in my configuration. Thank you guys!
Yes, I know your problem. Either you have not set the APN in the dialer to the correct server, or your mobile provider requires a proxy server for all http requests.
In the latter case, you can assign the proper proxy server in IE options to be associated with this particular modem connection.
HTH>
floepie said:
Yes, I know your problem. Either you have not set the APN in the dialer to the correct server, or your mobile provider requires a proxy server for all http requests.
In the latter case, you can assign the proper proxy server in IE options to be associated with this particular modem connection.
HTH>
Click to expand...
Click to collapse
thanks floepie!
I believe that the APN settings are correct.
I havent tried the proxy server settings in IE though.
Now, how do I assign a particular proxy setting (I guess IP address and port #, right?) to a modem only??
I appreciate your help!!
Hello everyone!!
I bet you're all frustrated checking this solution or that solution but in then end getting back to where you started at.
I've been there and done that and luckily for me, it's only been a week of sleepless nights to solve instead of months for some.
So, I am writing this thread from my Dopod 838 Pro, but it will work with any other Dopod/Hermes running on WM5:
Procedure by now I'm sure you will be used to:
1.Pair OSX and the phone. You might need to check the "any device" checkbox on OSX's pairing utility.
2. Verify to OSX that you do want to use that device as a modem (if you don't get that dialog, then you will need to create the Bluetooth connection yourself -- message me or leave a comment if you need instructions and I will reply to you).
3. Download the IPAQ GSM modem script at www.taniwha.org.uk
4. Go to your System Preferences/Network/Bluetooth/. There enter the following:
Service Provider: [blank]
Account Name: [check with provider]
Password: [check with provider]
Tel number: *99# THIS IS VERY IMPORTANT!! (the *99***1# number doesn't work with the HTC/Dopod phones)
On PPP options uncheck "tcp header compression".
On the Modem tab uncheck both "enable error correction" and "wait for dial tone". From the modem drop-down menu select the iPaq-GSM modem script.
Then, click Apply and then open the "Internet Connect" application and select Bluetooth from there. Click "Connect" and you should now be connected on the net via GPRS/EDGE.
Please make sure you've followed the instructions carefully. It may sound like the same as others but the key is the telephone number.
Good luck!
Art.
You may also use Internet Sharing application - I find this cleaner.
Basically, you just pair the phone from the Mac (be sure to initiate pairing form the Mac side - NOT the phone).
Then, launch Internet Sharing appliation and, choose bluetooth and hit START.
Then, under the Bluetooth icon (next to the Spotlight), select JOIN NETWORK ON [HERMES BT NAME].
Voila