HI all
I've been trying to CID unlock my G3 Wizard for hours now and can't seem to make it. I've downgraded to button 1.05, getting:
IPL: 1.05 (G3 device)
SPL: 2.16 (G3 device)
Now when I try to run Lockiwiz (and i've tried all the versions), after pressing c and <enter>, the DOS window just closes and nothing happens.
When I try unlocking CID with WST tool, i get an error:
SPL version is 2.16.0000
DOC chip is write-protected!!
Downgrade SPL to no higher than 1.06 and
repeat procedure.
I've spent about 7 hours trying to get my device CID unlocked and upgrading to WM6 finally, but no luck so far.
Can anybody halp me?? PLEEEAAASE!
Related
I have Qtek 9100, ROM version of this device is 2.17.7.2 WWE.
IPL 2.17.001
SPL 2.17.001
GSM 02.07.10
OS 2.17.7.2
I did the following operations to make the device SUPER CID:
I synchronized the devece with Active Sync 4.1 .
I started aWizard 1.3 beta 1.
I checked options u and e with aWizard 1.3 beta 1.
Then I started Lokiwiz02b and checked option C.
But it did not help.
After that I tried application unlock for SDA, and then started option C with Lokiwiz02b, but it didn't help.
How can I make the device SUPER CID?
Follow instructions here http://forum.xda-developers.com/viewtopic.php?t=47848
You need to downgrade to this rom first ftp://xda:[email protected]__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
EDIT Further to advice below ignore above advice.
As of now, there's NO FREE option to do CID unlock on Wizard with G4 chip (IPL/SPL end with .0001)
The only way to have CID unlock on your phone is to use the service at http://www.imei-check.co.uk (about US$40)
The FREE option for your device for now is SIM unlock by using Lokiwiz 0.3a
If the IPL and SPL have ".001", don't attempt to flash with existing roms unless the rom explicitly supports the G4 bootloader... there are a good amount of G4 Wizards that are bricks because of this.
alex-urmas said:
I have Qtek 9100, ROM version of this device is 2.17.7.2 WWE.
IPL 2.17.001
SPL 2.17.001
GSM 02.07.10
OS 2.17.7.2
I did the following operations to make the device SUPER CID:
I synchronized the devece with Active Sync 4.1 .
I started aWizard 1.3 beta 1.
I checked options u and e with aWizard 1.3 beta 1.
Then I started Lokiwiz02b and checked option C.
But it did not help.
After that I tried application unlock for SDA, and then started option C with Lokiwiz02b, but it didn't help.
How can I make the device SUPER CID?
Click to expand...
Click to collapse
What am i doing wrong? I have a cingular 8125, I installed lockwiz 2 and followed the instructions. It installs on my phone fine but everytime i run Lockwiz .bat i type in "U" hit enter and the screen dissapears and it does nothing. I downgraded my ROM. It reads:
IPL 1.08
SPL 2.25
CSN 01.09.11
OS 1.8.11.1
Please any help would be greatly appreciated!
You're IPL/SPL should BOTH be 1.xx before you can succesfully unlock. Follow:
http://forum.xda-developers.com/showthread.php?t=298613
hi,
im a noob to this forum and pocket pcs and i think im doing something wrong but when i try to install mfrazzz's xda mobile 6 release 5 final. i its still the same old windows mobile 5
i think my cid is unlocked i followed the instructions given by farias thread.
how would i know if the cid is unlocked? i tried using mestrini's WST tool but i get an error.
thanks in advance
thanks for the help
7331ymerej said:
hi,
im a noob to this forum and pocket pcs and i think im doing something wrong but when i try to install mfrazzz's xda mobile 6 release 5 final. i its still the same old windows mobile 5
i think my cid is unlocked i followed the instructions given by farias thread.
how would i know if the cid is unlocked? i tried using mestrini's WST tool but i get an error.
thanks in advance
Click to expand...
Click to collapse
Always post vital data of the phone,untill it's not known which device you have,G3 or G4,it's hard to provide with any help.Post IPL SPL of your device.
If it's a G3 then its CID locked,you have not followed the correct unlocking procedure.Read the Guide and sticky by Dr.Puttingham and follow it correctly to CID unlock the phone.
If it's a G4,then you cannot straight away flash any Rom to it,to upgrade follow the method as Sticky 'SoftSPL or HardSPL' by equinox in G4 forum.
What error it gives while usung WST 4.2 Tool ?
Cheers !
i have a g3, and the ipl: 1.01 (becuase i downgraded because the instructions told me to) SPL : 2.16
and the wst tool give me a "in the rexx script named : at line number :2840"
and is there a way i can change me ipl back to 2.16? cause nothing is working for me =/
thank you for your response
7331ymerej said:
i have a g3, and the ipl: 1.01 (becuase i downgraded because the instructions told me to) SPL : 2.16
and the wst tool give me a "in the rexx script named : at line number :2840"
and is there a way i can change me ipl back to 2.16? cause nothing is working for me =/
thank you for your response
Click to expand...
Click to collapse
ok, you got ipl 1.01 cuz you downgraded with Button's Rom 1.05 but your spl remained unchanged 2.16,its nothing to worry about,it sometimes take a little more tries to downgrade spl to 1.01,flash the Button's Rom 1.05 a couple of more times to make both ipl/spl 1.xx,only then you can CID unlock the phone with lokiwiz 02b.Follow the guide for downgrading and unlocking at the below link and do the method correct.Your phone is still CID locked,untill you get your phone CID unlocked you can not upgrade to any wm6 Rom.
http://forum.xda-developers.com/showthread.php?t=285435
But if you want to go back to your original wm5 Official k-jam Rom and have ipl/spl 2.16,then Download official k-jam Rom 'K-JAM_WWE_216901_2169101_020710_ship.zip' from official website of i-mate k-jam or from the following link below:-
ftp://ftp.clubimate.com
1.unzip the Rom zipfile,get your phone into bootloaders screen (multicolored screen)by pressing and holding down the camera button and the Power ON button together,the phone will start in bootloaders(multicolored screen) it'll show you ipl 1.01/spl 2.16
2.when in bootloaders,connect your phone with pc via usb cable, a small usb written will appear at the bottom of the multicolored screen of your phone.confirm it.
3.open the unzipped folder of the downloaded Rom,run the RUU icon in it(double click Ruu.exe)
4. follow the instructions and flash the Rom,after completion,your phone will restart and start working.
Good luck !
thank you sooo soo much, im gonna try it again right now
i guess my phones SPL will not change. i must of flashed the ROM with buttons 1.05 about10 times but it still wont change .... oh well im just gonna go back to the stock rom my kjam is WEIRD haha
Please Help
Hello
I have the Kjam G3 (with IPL & SPL 2.16) & wm5. I want to upgrade to wm6.1 but the CID is locked. I tried the WST tools and followed the instructions to unlock the CID but nothing happened.
Please can any body help me to solve my problem and tell me any other way to unlock and where to download the wm6.1.
THANK YOU
READ the FAQs, they hold all of the answers that you need.
I follow instructions on updating and unlocking G3 wizard using button 1.05 I downgraded rom, I did Lokiwiz when the phone rebooted I got Ipl 1.XX Spl 2.xx, I reran a second time and got the same Ipl and Spl, What am I doing wrong.
I don't think you are doing anything wrong, run it one more time and see if everything is okay after that.
These little monsters are tricky buggers, some people are good after one try - others two - you just may be one who needs to run it three times.
Good luck
dobbiedoo said:
I follow instructions on updating and unlocking G3 wizard using button 1.05 I downgraded rom, I did Lokiwiz when the phone rebooted I got Ipl 1.XX Spl 2.xx, I reran a second time and got the same Ipl and Spl, What am I doing wrong.
Click to expand...
Click to collapse
dobbiedoo said:
I follow instructions on updating and unlocking G3 wizard using button 1.05 I downgraded rom, I did Lokiwiz when the phone rebooted I got Ipl 1.XX Spl 2.xx, I reran a second time and got the same Ipl and Spl, What am I doing wrong.
Click to expand...
Click to collapse
Nothing to worry,sometimes Button's Rom 1.05 takes more then once to get both IPL/SPL same,keep on flashing the button's 1.05 for a couple of more times,till both ipl/spl get the same 1.xx,or you can try xda_minis_launch rom,it also helps in some cases,only after you have both ipl/spl 1.xx,then use lokiwiz tool to SIM/CID unlock the phone.
Cheers!
Hello everyone,
I am here to ask for some help from the experts.
I already read a lot in this forum but could not find any working solution.
My Prophet was upgraded to IPL/SPL 3.08 and won't turn on unless I connect +5v pn pin 1 and ground on pin 6. Doing this I can go to tricolor screen.
I tried to flash IPL/SPL 2.20 but after the reboots it comes back with IPL/SPL 3.08.
Any ideas how to downgrade the IPL/SPL ?
Best regards to you all and a warm thank you for the quality post in this forum.
Adias
Downgrade IPL/SPL 3.08 sorted
I sorted this in a moment of clarity.
Steps:
1. Got a working WM5 rom into the Prophet
2. Connected ActiveSync
3. Got prophet SOFT SPL into the phone device root.
4. Run SOFT SPL. Got a white Screen (Witch is normal. This is the SSPL bootloader screen)
5. Flashed IPL 2.20... OK
6. Flashed HARDSPL... OK (I supose SPL 2.20 can also be flashed)
Thevice unbricked and working fine.
congrats and well done
its even more satisfying when you solve it your self yes?
Can you please provide links for the SOFT SPL and HARDSPL files? Thanks men
asrdias said:
I sorted this in a moment of clarity.
Steps:
1. Got a working WM5 rom into the Prophet
2. Connected ActiveSync
3. Got prophet SOFT SPL into the phone device root.
4. Run SOFT SPL. Got a white Screen (Witch is normal. This is the SSPL bootloader screen)
5. Flashed IPL 2.20... OK
6. Flashed HARDSPL... OK (I supose SPL 2.20 can also be flashed)
Thevice unbricked and working fine.
Click to expand...
Click to collapse
Question hard spl
I already have de SPL 2.26 before I had 3.08. the question is, Do I have to run the hard slp? Thanks.