Related
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
Hi,
I started a new thread because on my previous post I did not receive that much reactions so I try a brand new one.
A few months ago I bought this, in my eyes, really cool HTC Trinity, aka the P3600. One of the main reasons I bought this device was because I read on some forums that this device had GPS functionality, but at that time it was not supported/ebabled yet by HTC but properbly would be in the future. Off course I could not wait, so I tried to install a Dopod version which should enable GPS functionality. Unfortunately I've got a Dutch version of WM5 running on my PDA, so a ROM upgrade was not possible, unless the CID lock is removed. In order to accomplish that I downloaded the tool SSPL, installed it, and executed it on my PDA. After that I tried to install the Dopod ROM, but during the upgrade it froze up. After rebooting, the device frooze up during the startup (when it is display the MS logo for push mail). After that I retried the to run the update, but unlucky me, it stucks at 1%, then device reboots, and I receive the "ERROR [294] : INVALID VENDER ID". on the screen of my PC. My PDA is now worthless because it still freezes up during tje startup.
I' m still able to access the bootloader menu however but none of the ROM updates that I have at my dispossal are working. Unfortunately I do not have the Dutch ROM in my possesion and a quest on the Internet lead to nothing. However, this week I will receive a Trinity at my work (exactely the same). Is it possible to make a backup of this ROM and then restore it back to my nearly dead PDA? Or should i deal with this dead PDA in anoter way to bring it back to live again.
Any help is more the welcome
Follow this thread to CID unlock then just re flash. This should take care of your invlaid vender issue.
http://forum.xda-developers.com/showthread.php?t=293957
RebelShadow said:
Follow this thread to CID unlock then just re flash. This should take care of your invlaid vender issue.
http://forum.xda-developers.com/showthread.php?t=293957
Click to expand...
Click to collapse
JolietJake's Trin is not booting to OS, he can't run SSPL
stepw said:
JolietJake's Trin is not booting to OS, he can't run SSPL
Click to expand...
Click to collapse
Yep, that's right... If I only could
You may have to suck it up and pay for the unlocker from IMEI-check. I may be wrong, but I think you run that from your pc and only have to connect your trin via usb. I'm just not sure if you need a valid activesync conncection to use it - as you probably can't get that with a "zombie" trin.
Do a little research first if you are going to try.
If you try it, good luck!
http://www.imei-check.co.uk/m700unlock.php
psargent said:
I'm just not sure if you need a valid activesync conncection to use it - as you probably can't get that with a "zombie" trin.
[/url]
Click to expand...
Click to collapse
I indeed need an active sync connection, which I have.....
....during 10 seconds or so (only just after I rebooted the TRIN)
I also tried to use this tool in Bootloader menu. It's able to set up a connection through USB, the screen on my PDA goes gray and the message ".....ERROR" appears on the screen of my PC. After that the TRIN reboots and freezes up again . Fortunately I did not pay for the tool yet, i just downloaded it)
However I appreciate your help very much!
psargent said:
You may have to suck it up and pay for the unlocker from IMEI-check. I may be wrong, but I think you run that from your pc and only have to connect your trin via usb. I'm just not sure if you need a valid activesync conncection to use it - as you probably can't get that with a "zombie" trin.
Click to expand...
Click to collapse
Too bad, it's the same story, it needs OS/ActiveSync to be running to re-enter boot and flash SPL.
After (I think) successfully upgrading to WM6, I've had a few problems...
1) I can't seem to soft reset anymore (holding down Power at the top + the reset button)...it seems the only way I can now reset my unit is by physically removing the battery...
2) I can't access the bootloader SERIAL mode...I can access the options for the kernel hive and formatting storage, but no success being able to get into USB mode to reflash my unit
Any help or suggestions would be greatly appreciated - I only bought this phone on Friday
1. This was hard reset in WM2003 - for soft reset just press the reset button
2. You need to press and hold power+reset+record(WMP) buttons at the same time
I suggest you read WIKI first before asking questions which are answered a million times
Thank you for the prompt reply.
I can understand your frustration with many people constantly asking these questions, but please don't make me feel like an idiot when I've actually read the Wiki and tried Googling the problem prior to posting.
To clarify, I know *how* to access the SERIAL option (I had to do it to upgrade from 2003 to WM6 to begin with). My point is that holding Reset+Power+Record doesn't work anymore. It just continues the boot process and goes straight to the Windows Mobile splash screen. The reset button, in and of itself, does nothing at all. I've tried everything from just tapping it a few times to pressing and holding it for upwards of 30 seconds...but it doesn't seem to do anything for me.
Try to hold and press power+record+cam buttons then press reset while holding those buttons.
Yeah, it does nothing...I have a feeling that the actual reset button is no longer working on the unit...not sure if that's to do with the upgrade to WM6, or if it's a hardware problem and just happens to be coincidence :-/
don't take xplode's advise wrongly. it's just that reading AND understanding the WIKI is important especially for beginners like yourself.
if you think you've successfully upgraded to WM6, it's probably because of the "Congratulations" message that was displayed... well, you're almost there, though not quite.
try to fully understand the no/yes/yes instruction in the WIKI... the reset+power+record combination is NOT what you should be doing. it has been replaced by another... here's the thread that could guide you... http://forum.xda-developers.com/showthread.php?t=327978&highlight=kitl
and here's the pertinent wiki page...
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4
good luck and welcome to the BA community.
Anyway if this that you try to explain is that the hardware buttons no longer work, you can try the MTTY method, if you have read the wiki you already know what exactly to do
Thanks raymonds, I will try not to, but I just don't want people thinking I'm yet another new member that doesn't read anything before posting, because I know how much I hate that too...I tried reading up on my problems for 4 hours last night before deciding to post because I couldn't find anything else to help.
I have successfully upgraded to WM6 and went through the no/yes/yes steps - the issue is that I want to go back to WM2003 or WM5...they seemed far less problematic for my phone for some reason..one problem I'm facing now is that my BA, pure and simple, no longer recognizes that I have a cellular carrier at all, making it essentially useless as a phone. When I try to go into SIM Manager, it hangs for a while, then goes into the screen saying that only emergency calls can be made...but when I try to put in my PIN, it says "Unknown SIM error", though the SIM works fine in my other phone...
I'm trying to use the Power/Reset/Record to either try reflashing in the hopes that'll resolve my issues, or downgrade...either way, it's not allowing me to do so, and I obviously can't do this while the phone is booted into WM6. It just seems like the reset button is no longer working, since neither combination that uses it (Power+Reset or Power+Camera+Reset) works anymore.
try to downgrade with MAUpgradeUT_NOID.exe, and then reupgrade, another thing you can do is to reflash the radio rom. The MTTY method resets bootloader settings which may be the solution to your problem.
MTTY under Windows XP is explained HERE
xplode, mtty requires one to do the power+reset+record combination, which he currently cannot do.
is this a second-hand unit?
Hm, there was another way to put your device into bootloader mode but i have never tryed it, in most of the WM2003 upgrades there was EnterBL.exe, and when you copy it to the device and execute it the device goes to bootloader mode...
but it also creates problems - read here
Also i had problems in the past with the latest version of MTTY (1.45) and used previous one 1.01 which worked like a charm
Sweet - thanks xplode and raymonds for your time.
Unfortunately I can't try these as I am at work right now, but I do appreciate the suggestions and will try them as soon as I get home.
If I can't get it to work, oh well - off to the service depot and a (probably) expensive lesson learned.
Please keep us updated, about your issue
Thanks guys...
So, I'm taking it that the radio stack is now corrupt, since it's no longer even showing a version number on my BA. I tried the methods xplode suggested - when I enter the unit into KITL mode, I take it I'm supposed to use USB Active as the transport method, since MTTY won't recognize a device otherwise, and my phone just boots into Windows from that point.
When I try to run MTTY though, all it does is display "kITLª" over and over again...I'm not sure if that's normal, or even how to enter a prompt of some kind...
I'm starting to wonder if maybe I should just take it to the depot, pay the $75 I was quoted, and learn my lesson... :-/
Any other suggestions, or am I just totally doing what you suggested wrong?
You do not need to enter KITL because this is used to debug your WM build using Platform builder
Just try to put your device to botloader mode and then use MTTY to instruct the bootloader what to do, or just reflash radio and then new rom
I have upgraded from WM2003SE to WM6 (the first released from XPlode version OS 5.2.1620 build 18125.0.4.2) without any problem. Now I want to upgrade from that version to the current release, but the ActiveSync (I am using 4.5) always disconnect after MaUpgradeUT_noID has detected the previous installed OS. So I got an error message like "cannot to the device" or so. It happens everytime even I just try to upgrade the Radio rom.
I have also tried to use ActiveSync to version 3.8 (I found this suggestion from this web site) but bad luck it can't detect my BA device at all. I have also tried to revert back to WM2003SE but still get the same problem. My system is WinXP SP2 & O2 IIs. So Please help I am in the dark right now.
Same problem here...
su2003 said:
I have upgraded from WM2003SE to WM6 (the first released from XPlode version OS 5.2.1620 build 18125.0.4.2) without any problem. Now I want to upgrade from that version to the current release, but the ActiveSync (I am using 4.5) always disconnect after MaUpgradeUT_noID has detected the previous installed OS. So I got an error message like "cannot to the device" or so. It happens everytime even I just try to upgrade the Radio rom.
Click to expand...
Click to collapse
get into boot loader mode,then try
(press record button + power button and reset at same time)
addan said:
get into boot loader mode,then try
(press record button + power button and reset at same time)
Click to expand...
Click to collapse
Have tried that already but still get the same error. I have even reformatted my PC and reinstalled WinXP and ActiveSync 4.5 just in case there are viruses or so but also get no luck.
Did you soft (or hard) reset your BA and reboot your PC after failure? (Try clean upgrade, and in bootloader).
Did you (succesfully) establish an ActiveSync partnership before upgrading?
Did you try unchecking Enable advance network functionality in USB to PC (under settings, connections)?
Did you soft (or hard) reset your BA and reboot your PC after failure? (Try clean upgrade, and in bootloader).
Yes, at this time you asked me. Nothing changed.
Did you (succesfully) establish an ActiveSync partnership before upgrading?
Yes.
Did you try unchecking Enable advance network functionality in USB to PC (under settings, connections)?
Yes. I did it.
More over, if I started BootLoader mode before execute MaUpgradeUt_noID.exe the program get struck while performs device information checking, I have to pull it out from Sync station the program then continue running but without any information (like the existing OS version etc.)
how long did you wait for the program to respond before you find that its stuck ?
Here it takes about 2 min to find the device
Proper upgrading procedure, as it was said 10000's of times
1.put your device in bootloader mode
2. place it to cradle
3. kill activesync (optional - if you dont do it the upgrade utility will do it for you, but sometimes activesync stays on and fail the upgrade process)
4. start upgrade utility and follow the onscreen instructions
5. perform hard reset (the three options thing)
thats all
Xplode's new cube cab
deleted... off topic
how long did you wait for the program to respond before you find that its stuck ?
It was about 5 min and the program still had no responses. I then have to pull it out and the program continue running but without any information (like I had mentioned it before).
Here it takes about 2 min to find the device
Unfortunately not with mine.
Proper upgrading procedure, as it was said 10000's of times
1.put your device in bootloader mode
Yes. I did it.
2. place it to cradle
Yes. I did it.
3. kill activesync (optional - if you dont do it the upgrade utility will do it for you, but sometimes activesync stays on and fail the upgrade process)
I have tried it both with and without killing the activesync.
4. start upgrade utility and follow the onscreen instructions
Yes, but once I started the upgrade I have noticed that the activesynce has disconnected my device.
5. perform hard reset (the three options thing)
I didn't have chance to go to this point.
thats all
I think the main problem is the activesync has disconnected my device suddenly when started the utility. I have also tried to take out anythings that using USB port like mouse, ext. DVD, printer, scanner just in case the upgrade utility may conflicts with those devices.
I think I shall try to change the PC to upgrade my device to make sure that it wasn't caused from hardware defection.
su2003 said:
4. start upgrade utility and follow the onscreen instructions
Yes, but once I started the upgrade I have noticed that the activesynce has disconnected my device.
5. perform hard reset (the three options thing)
I didn't have chance to go to this point.
thats all
I think the main problem is the activesync has disconnected my device suddenly when started the utility. I have also tried to take out anythings that using USB port like mouse, ext. DVD, printer, scanner just in case the upgrade utility may conflicts with those devices.
I think I shall try to change the PC to upgrade my device to make sure that it wasn't caused from hardware defection.
Click to expand...
Click to collapse
With regard to your last remark: you stated earlier you did a fresh reinstall of XP. Now, why would you install and connect all these peripherals if you only want to upgrade your BA rom??? All you need is a fresh WinXP and ActiveSync...
Did you really do a fresh install and follow the wiki and the tips mentioned again (and again)?
You are getting me (and probably all of us) confused.
Your answers to especially points 4 and 5 of xplode tips to me clearly indicate that you do not really take (enough) time to understand the procedures (or what you are doing) and want to have WM6 running asap with no effort at all...
Your remark "I think the main problem is the activesync has disconnected my device suddenly when started the utility" only confirms this as this is the whole point of boatloader and was furthermore indicated it would do exactly so by xplode earlier on.
Please do take time and hence show consideration to all of us that are trying to help you in preparing yourself properly before trying to attempt any further upgrade.
Good luck!
With regard to your last remark: you stated earlier you did a fresh reinstall of XP. Now, why would you install and connect all these peripherals if you only want to upgrade your BA rom??? All you need is a fresh WinXP and ActiveSync...
Did you really do a fresh install and follow the wiki and the tips mentioned again (and again)?
You are getting me (and probably all of us) confused.
First of all, Sorry if I make you and other confused. I have began to unsuccessfully upgrade my device since Friday. So I decided to help myself at first by try to do everything I can do by myself. I have formatted PC HDD and also reinstalled activesync because I thought the utility may conflict with other program on my PC or from Viruses. I have also tried many ways with hard reset and cold reset etc. to upgrade my device but have no luck. That was with very fresh new installed WinXP PC. Unfortunately, I have to use this computer for my job also. So that's why I have to install printer & scanner driver including MS Office, AutoCAD and other necessary program to serve my job . I have falled with upgrading but I do not want to have problem with my job. Hope you understand my essential.
Your answers to especially points 4 and 5 of xplode tips to me clearly indicate that you do not really take (enough) time to understand the procedures (or what you are doing) and want to have WM6 running asap with no effort at all...
Since I began to upgrading and everytime I have executed the utility I have always wait & wait but I just never look at the clock to see how long I have waited. Xplode has just warned me to take enough time so I started to upgrading but with clock at this time. I have already mentioned that I have successfully upgrade from WM2003SE to the WM6 (previous version) so as a user I have enough experience and know what I am doing.
Your remark "I think the main problem is the activesync has disconnected my device suddenly when started the utility" only confirms this as this is the whole point of boatloader and was furthermore indicated it would do exactly so by xplode earlier on.
This is just my opinion to let you guy see and understand the problem. That's it.
Please do take time and hence show consideration to all of us that are trying to help you in preparing yourself properly before trying to attempt any further upgrade.
I think I have already put a lot of effort about upgradind my device. I have reformatted and reinstalled all necessary programs. It took me out almost half a day to do this. And not only with my PC I have also reinstalled all programs on my device with an old OS version since I have lost them all from hard reset. Other than that I have also tried & tested upgrading the device during the time. The only word I can say that It was not funny to do all of this. It was not really a hard job but it took almost my weekend time.
Good luck!
Yes I do need it barely. Actually I have already felt a little lucky got from all of you that try help me solving the problem. Thanks.
su2003, nice answer.
His main problem is that he does not understand that activSync will work if the device is in a normal state but when device goes to bootlogger mode, its only USB connection that will help a PC to talk to Device and not activSync.
April 1 said:
su2003, nice answer.
His main problem is that he does not understand that activSync will work if the device is in a normal state but when device goes to bootlogger mode, its only USB connection that will help a PC to talk to Device and not activSync.
Click to expand...
Click to collapse
Thanks for your additional.
I have also tried using different PC to upgrade the OS but got the same result.
you have to be sure that your BA when cradled display USB (after getting into bootloader mode) instead of serial 2.06 than run the upgrade utility
I am quite sure that the screen has displayed USB but the number is 2.07 not 2.06. I am not sure about the meaning of the number, it could be the version.
I have also brought a new USB-XDA IIs cable yesterday, just in case the cardle was defected but it doesn't work also, I have got the same result.
khanem said:
you have to be sure that your BA when cradled display USB (after getting into bootloader mode) instead of serial 2.06 than run the upgrade utility
Click to expand...
Click to collapse
I am quite sure that the screen shown USB 2.07 (should be differ version than your).
I have also brought a new USB-XDA IIs sync cable but getting the same result.
Conclusion:
Bad Hardware(Flash ROM)?
Your Bootloader is toasted or had it's LAST flash of it's lifetime???
We can say that... but hopefully not for your sake.
Because as you have said you've done EVERYTHING that was posted.
and though our Senior's "inputs" didnt worked out the way it SHOULD work.
I cant say it's a waste of time to answer your questions.
But there are no more questions to ASK
and there are no more questions to ANSWER
They're all been said here.
All you have to do is PRAY HARD leave the BA rest for a day...
remove the battery...
think things out, clear your mind... sleep...
then execute Xplode's Walkthrough from Step 1 the next day.
but be sure to have the battery fully charged.
Your BA is not dead and your bootloader is not toast. The only problem you have is probably you are impatient. Go to the Wiki and follow the procedure exactly as it is written. It will work. By the way, if you kill Activesync (ie disable USB connection in activesync connection setting), put your device in bootloader mode and connect your usb cable (in that order), run the upgrade and it will work. Forget about activesync.
su2003 said:
I am quite sure that the screen shown USB 2.07 (should be differ version than your).
I have also brought a new USB-XDA IIs sync cable but getting the same result.
Click to expand...
Click to collapse
I use xda IIs and the bootloader mode shows ver 2.07, and i dont have any probs installing. I dont think the version 2.07 has got something to do with your problem.
You said that you tried other pc and it doesnt work, and it worked before when you upgraded previously. I think you know enuf about upgrading if you have done it before....
did you have problem with sync connection before? I was just thinking maybe there is something wrong with your BA....like actual hardware problem with the cable connection??
what about firewall? would it affect it - I doubt it cause its not in sync mode.... but at this stage, maybe just try all possibilities to try to get it working.
Good luck
Mhm. I'm not sure I've really followed all the intricacies of this case ... But whatever, here's my two cents for a safe upgrading procecedure:
1) use a cradle, not a USB cable, and make sure the cradle's
power supply is plugged into a wall outlet. It also helps to make
sure the cradle is plugged directly into the PC, not via any kind of
USB hub. No other devices should be connected to that same USB
channel. I suppose temporarily disconnecting other (unneeded) USB
devices from the computer can't hurt, either.
2) I guess "kill ActiveSync" can mean various things ...
however, here's the best way to do it I think: as sofene mentioned,
disable USB connections (what the hell - disable ALL connections) in
ActiveSync settings. Then reboot the PC. No need to look for ActiveSync
processes and kill them manually -- disabling the connections will take
care of that. Rebooting ensures that ActiveSync's driver code is really
unloaded.
3) remove SD card and, for good measure, SIM card from the BA.
4) perhaps soft (or even hard) reset your device
5) put device in Bootloader mode
6) insert device in cradle, start upgrade utility, off you go ...
By the way, ActiveSync has got nothing to do with the ROM upgrade utility, and it should therefore not have been necessary to re-install ActiveSync, etc. You just have to make sure it does not get in the way of the upgrade process. As far as I understand the process, the ROM upgrade should work equally well on a PC that does not even have ActiveSync installed.
OK heres my situation:
i upgraded from the stock o2 wm2003 to wm6 using the wiki ROM:
Helmi Windows Mobile 6 Profesional R0
CE OS 5.2.1620 (Build 18125.0.4.2)
now on bootup it says
R:none
G:none
D:5.60.00 WE
It boots up fine but....
i cant get any reception.- just says "no service"
i have also tried disabling and re-enabling "Phone" in com manager
Yes, i have done a soft reset, hard reset and ive tried XPLODE wm6.5 and my current wm6 ROM.
XDA unlock all reported a successful unlock.
HELP!!!
OK, i did the thing in the ROM post said:
"R None if you take out battery and turn it on without push the reset button twice.
SDK?"
and it works now but when i turn it on i have to press the reset button twice every time
can someone help?
first of all you must unlock sim under WM 2003, then remove the extrom of 2003 to gain adidional 16 mb of storage (resize DOC), then you must upgrade to radio version 1.15 and then you must try any WM5, 6, 6.1, 6.5 rom
so now flash your shipped rom, you may find preferred rom for your operator in my signature, then start everything from the beginning
ok, it has kinda settled down now, working as normal.
I have "unlock sim under WM 2003, then remove the extrom of 2003 to gain adidional 16 mb of storage (resize DOC)"
If i wanted to upgrade my radio version would i have to flash the ROM again?
no you can flash radio rom only without the OS
Jejeje
Hey Xplode i never was able to see that tools like unlock extrom and repart DOC works on my BA... it always shows an error! when i execute the unhide hide repart etc etc.. so I upgrade even tought jajaja.
they only work on WM 2003
xplode said:
they only work on WM 2003
Click to expand...
Click to collapse
are you sure xplode, cause i unlock my phone using the tools from the BA wiki and im using wm6.5.
ok,
i upgraded my radio to 1.15.....
but i still got the problem
none
I get this on my wm6.1 but normally gets sorted after a soft reset
HMM!!!!
Same problem, after updating from stock WM2003 to WM6.1PRO all steps done like the wiki steps except the ExtRom step, couldnt get the unhide, unlock program to run (missing file or libraries error), so i flashed sun's WM6.1PRO without the extra storage, now when i change the battery i get the NO radio bootloader, still im able to fix it by doing a soft reset, but the strangest thing is that im not able to use the wifi :/. So the thing is, when i turn on without the radio i can use the wifi, but no the phone(airplane mode), and when i do a soft reset, the radio shows and i can use the phone but the wifi doesnt turn on at all!. Any help please, dont make me choose betwen my phone and my wifi
PD: is not only the radio missing the i change the battery, also R:none G:none
I have a Qtek9090
very odd ,i can use my wifi when the phone is on.
But i went from wm2003 to wm6.5 to wm6
wierd....
so, is there a solution? I've got the same problem
Ops! Solved. Do a soft reset via the button.
(I always do a softreset via unlocking the battery and locking it again)
Every one here should know that there is no WM 6 for BlueAngel by microsoft. it is ported on BA by helmi_c and that >> R none and G none << Bug is in WM 6 from very first day. SO Whenever u pull the battery out u need to SOFT Reset the device after putting the battery on phone.(u need to wait to start the phone to reset, just put the battery and insert the stylus at reset point.)
there is no point discussing about this anymore. thread should be closed.
i have the solution about this problem, im recovery from it.
first of all, downgrade ur ba tu ship rom, and go back to upgrade 6,5 rom, after finis doit "WM5" hardreset.... search the way in wiki.
wala........its done and run normal r;none g;none not see again. have try it
This is an old problem... Rnone Gnone
solved by sticking your soft reset button after changing battery or a hard reset.
The Wifi-Phone problem is solved by buying a new battery. The Wifi module wont fireup because of the lack in power draw since the phone is using much of it.
Buying a new battery solves plenty of problem. even OS speedup because it solves the lag the "modules" (e.g camera/lan/phone/mmc) detection gives while in bootup or execution.
If you still have problems. We can always point to the wiki.
Have a nice day!
-SS-