Mogul Dead will not boot HELP! - Mogul, XV6800 General

Ok my mogul went dead before I could get it plugged in, so I plugged it up come back later to cut it on and it goes to the plain HTC screen and hangs... I tried a hard reset same thing, tried putting the latest DCD rom back on it and same thing.. Can someone help me... the only thing it seems to be able to do is go into the BL mode and the hardreset mode.
FYI.. Mogul has been running for a week or more since the unlock. And I was so pleased with the new proformance. Thanks for the help.

I had the same thing happen to me this morning... and I just barely installed the sprint 2.17 ROM, and it seems to be booting just fine. You could try that. Thing is, though, I'd expect DCD's rom to work just the same way, so I don't know for sure what to tell you. I've got the custom BL installed, and I've been running DCDs ROM. I just decided to switch back right now because A. I'm not at home and only had time to download one ROM, didn't want to risk needing to do it twice, and B. I wanted to compare which is really better and decide why.
The coolness factor on using a custom rom is, of course, good... ;-) but I want to see what the full differences are.
Anyway, I'd try that if DCDs rom isn't fixing it for you, because when I reflashed it it came right up.

taxilian said:
I had the same thing happen to me this morning... and I just barely installed the sprint 2.17 ROM, and it seems to be booting just fine. You could try that. Thing is, though, I'd expect DCD's rom to work just the same way, so I don't know for sure what to tell you. I've got the custom BL installed, and I've been running DCDs ROM. I just decided to switch back right now because A. I'm not at home and only had time to download one ROM, didn't want to risk needing to do it twice, and B. I wanted to compare which is really better and decide why.
The coolness factor on using a custom rom is, of course, good... ;-) but I want to see what the full differences are.
Anyway, I'd try that if DCDs rom isn't fixing it for you, because when I reflashed it it came right up.
Click to expand...
Click to collapse
Have you tried removing the battery for a few minutes.

I assume he tried that... I sure did. Update, however... the phone worked fine all day until I had to turn it completely off, and so I just pulled the battery; same problem recurred.
maybe I need to restore the original bootloader? dunno.

Well, I'm tring to load the stock 2.17 rom back on... Took it to the store they looked at it put it in bl mode and handed back and said it was my problem since I modded it. Guess I'm going to short it out so that insurance will cover it.

UPDATE : Ok so the 2.17 rom did allow to boot back up to a normal state, so maybe there is a problem that if the phone goes dead on the custom rom that dosn't allow it to recover, kinda wierd.
Thanks for the help, I was really pissed about sprint not replacing it. (HEHE, guess thats what goes with customizing your phone)

I've got mine back up and running DCD's latest 2.1.0 and it's great.
you can put everything back so that sprint doesn't know you did anything, so I wouldn't worry too much on that score. Other than that one time, I haven't had an ounce of trouble with it. don't let this turn you sour to custom roms, you'll miss out on some cool stuff... gps, for example.

doesn't boot
please help, i folowed the instructions from this website: http://www.phonenews.com/how-to-add-gps-to-htc-mogul-xv6800-p4000-titan-2663/
i opened up Hard-SPL-240-MFG.exe i got the 3 color screen and then i could'nt get active sync to work finnaly after a few reset and even a hard reset i got the 3 color screen to go away but now phone won't boot, the phone gets stuck by the htc screen can any help me in detail how to get the hone to reboot, when i reboot it displays that it has 3.27 and the 2.17, thanks in advance

that radio and rom version are incompatible with each other.

Related

Did i brick my Tmobile MDA? HEEELLLLPPP

Hey guys i tried flashing my rom using the Shelltool. I loaded the two cabs on the device and put it back to Tmobile 2.26. While i was in the shelltool it told me to do a hard reset and i think the phone was frozen (it didnt go to the normal colorful screen like usual) so i took the battery out of the back and powered it on. I left the software running like it said but it just froze up.
Now my MDA wont move past the Tmobile screen. I REALLY need a hand with this because this phone keeps my life in line! I dont even think ill be able to get up tomorrow because all my alarms go off my phone
Let me know if theres anything i can do otherwise im looking at a Motorola A1200 :-(
kind regards,
Eddy
Hi there,
Not familiar with Shelltool. I do most of my flashing using ActiveSync. Have you tried forcing the phone into Bootloader Mode (hold the Camera button while turning it on). Worth a shot.
If t-mobile was the original ROM on the phone, then just flash it again using the exe (or RUU if you extracted the files from the exe) instead of using shelltool and see if that brings it back to life.
well its stuck on the tmobile splash and shows no actual connection to the machine would it still work?
If you can get into bootloader mode then you should be fine. Just put your device into bootloader and flash wizard love rom or the rom that your device came shipped with.
Good Luck
looks like its working guys but its most likely still going to look and be WM5. Im still willing to try and get WM6 on it tho. I have the roms but its just not working any ideas?
Well, if you're flashing the t-mobile ROM right now then it is going to be WM5. Since you now know what to do if the ROM your loading doesn't stick, try flashing the ROM you were trying to flash again. By the way, what was your IPL and SPL before you flashed it the first time where it didn't work? If it was less than 2.xx then that was your problem most likely. If you're now updating to the latest t-mobile ROM the way I told you to (using the exe or RUU) then your IPL and SPL now should work fine with WM6.
Well I just finished upgrading my MDA to WM6. Here's what I did. First off I
fould out that you need the phone CID Unlocked for it to accept the WM6
ROM. Follow the instructions on this thread by Dr. Puttingham.
http://forum.xda-developers.com/showthread.php?t=285435
This should get your MDA ready provided it is a G3 (thread will tell you how
to tell the difference.) Then follow the directions on mfrazzz's thread:
http://forum.xda-developers.com/showthread.php?t=324632
I had problems with my MMS after the update but after re-installing the WM6
ROM and installing the CAB files by Lurch anf FZZF I got that problem
squared away. Believe me when I say I know what you are going thru. I
was fiddling around with this for about a week. Luckily I am on vacation and
I had plenty of time to read and decipher alot of the info I found. Good luck
and remember to READ, READ, READ. BTW, props to all that contributed to
these fine tutorials and for this awesome ROM. I have it running on my MDA
for three days now and am very happy with it. I am also using the 3.08
IPL/SPL which seems to give me better reception, which my wife seems to
appreciates

a little big problem

hi guys
my blackstone behaves strange from the last time a flashed a new ROM:
-my camera only works from time to time
-sometimes the screen(or the entire phone maybe) dosent boot up( I put in the charging clable and leave it, and when i come back the screen doesent light up, i try to reset and nothing, I pull out the battery and still nothing it only vibrates)
could this be a software problem or should I send it back for warranty?
Did you flash an upgrade of your official (stock) rom? What kind of rom did you install?
Anyway, backup everything, download the rom again, flash again, hard reset (you will lose every data on your device, hence the backup), boot, restore contacts, test your phone.
If everything works fine, the problem was caused by a bad flash or by some program you installed.
Good luck
it wasn't the official one, i flashed energyROM leo( the latest one)
i tried reflashing another one but not official
and I hard reseted it and the same, the camera doesent work
im gonna see later if i the flash official one fixes something
btw is there someplace i can get official vodafone ROM? because i coulden't find only orange...
2dy said:
it wasn't the official one, i flashed energyROM leo( the latest one)
i tried reflashing another one but not official
and I hard reseted it and the same, the camera doesent work
im gonna see later if i the flash official one fixes something
btw is there someplace i can get official vodafone ROM? because i coulden't find only orange...
Click to expand...
Click to collapse
Did you follow proper guide for flashing? i.e. did you use USPL or HSPL? Stock roms can be found here
2dy said:
hi guys
my blackstone behaves strange from the last time a flashed a new ROM:
-my camera only works from time to time
-sometimes the screen(or the entire phone maybe) dosent boot up( I put in the charging clable and leave it, and when i come back the screen doesent light up, i try to reset and nothing, I pull out the battery and still nothing it only vibrates)
could this be a software problem or should I send it back for warranty?
Click to expand...
Click to collapse
the same has happened to me using energyrom latest rom, my phone was working fine, now just keep cutting out and going blank charges fine and vibrates when u turn it on, but i just get a blank screen
danjohnson19855 said:
the same has happened to me using energyrom latest rom
Click to expand...
Click to collapse
Ahem... good to know...
u used USPL i flashed it a couple of times before this and it worked fine,
i dont know, im gonna flash it woth official one and see if it continues if not im gonna send it to warranty ( if i still have it ) thx
It has nothing to do with the ROM, maybe the download was corrupted, but with the way you flashed (USPL/HSPL, rom on storage card, etc) and if you did a hard reset (or two hard resets).
As the mighty though Fallen Spartan said, follow the guide: http://forum.xda-developers.com/showthread.php?t=505377
you could also revert back to a stock-rom and reflash
did u find out the problem, mine works for about 6 hours and then goes blank , i take the battery out for 20 mins and restart the device and it boots up ok, its proper wierd
If you're using the latest Energyrom with 6.5 23081 then the problem is a bug with this build from microsoft.
It is a known issue in the WM 6.5 thread that the latest WM6.5 23081, 23085, 23502, 23504 has a bug where the phone does not turn back on from suspend. i.e. when the screen is blank and you press the power button to turn it on, it does not turn on and you have to reset the device. That's why I have not upgraded yet.
crav4speed said:
If you're using the latest Energyrom with 6.5 23081 then the problem is a bug with this build from microsoft.
It is a known issue in the WM 6.5 thread that the latest WM6.5 23081, 23085, 23502, 23504 has a bug where the phone does not turn back on from suspend. i.e. when the screen is blank and you press the power button to turn it on, it does not turn on and you have to reset the device. That's why I have not upgraded yet.
Click to expand...
Click to collapse
i started using that rom then changed but i still get the same problem is there a way of fixing it?
2dy said:
hi guys
my blackstone behaves strange from the last time a flashed a new ROM:
-my camera only works from time to time
-sometimes the screen(or the entire phone maybe) dosent boot up( I put in the charging clable and leave it, and when i come back the screen doesent light up, i try to reset and nothing, I pull out the battery and still nothing it only vibrates)
could this be a software problem or should I send it back for warranty?
Click to expand...
Click to collapse
if ur havning problems with a rom u downloaded please go back to the post of that rom and ask ur question there,
Not rom problem ...
wingtytn said:
if ur havning problems with a rom u downloaded please go back to the post of that rom and ask ur question there,
Click to expand...
Click to collapse
AFTER 4 months of use my tohc hd start this behavior of not turning back from suspend mode and what I learned is that is some kind of hardware problem not rom related ... some believe it starts after some drop to the floor... but no one is sure the real cause .... I will by another ... maybe touh hd 2 ....

Stuck on the G1 logo after trying to load a new rom. I will try to put the rom on...

I'm stuck so maybe the rom didn't load onto the sd card correctly? It just stays on the logo forever. I can pull the battery and get back to the screen so i can do a wipe and reload the rom then reboot it, but it just stays on the logo. I will put a fresh rom or a different rom to see if that does anything.
ok so I put cyanogen's 1.51 build on and it booted up
Maybe the other one was corrupt. But I want to put the newer one on later.
No need for double posting, simply merge your two comments by editing your initial post.
but why are you running such an old build of cyanogen?
yeah I should have remembered to edit
I tried putting the latest one, but for some reason it kept hanging up on the logo. I just decided to try a previous one. I can try the new one again. I put the wireless tether program on and it's pretty nice, so no rush for now. Do you recommend a rom that gives it a different look?
When I want to change the rom but keep all my programs I can do that right? I know there is a way to back up what I have, but I'm not sure if it will just back up the programs and reinstall them onto the new rom.
Wow what took you so long to upgrade? Anyway if you go to Cyanogen's post and follow his instructions he posts on his website you shouldn't have a problem. There is probably a couple updates you need to do to the phone itself before you can even upgrade the rom
Technically I don't have the phone yet, but don't tell my gf.
psychoace said:
Wow what took you so long to upgrade? Anyway if you go to Cyanogen's post and follow his instructions he posts on his website you shouldn't have a problem. There is probably a couple updates you need to do to the phone itself before you can even upgrade the rom
Click to expand...
Click to collapse
It's supposed to be a xmas gift. I followed the root and other instructions to a Tee, but it just did that. So I tried the one that was out just before that and it worked. I will try it again later, but I want to read so more and figure out how to keep all my programs. Will I have to reinstall them all over even if I back them up?

official at&t callerID update bricked my phone.. :(

after my phone rebooted once the update was complete, it wont get passed the "at&T World Phone" white screen... SOMEONE PLEASE HELP ME!!!! i was using a stock at&t pure with the stock rom. i can not upgrade hardspl or ANYTHING any suggestions on how to get my phone to boot? hard-reset went through with no signs of failure but it still will not boot up after that finishes... sorry if its something im overlQQKing, but i just cant figure it out. n yes i have researched although obviously not enough at this point. Thanks to anyone who can help in advance. forgive my stupidity!!!
......
noone?????
The HTC Pure updates hosed my phone too, I had already applied hard-spl to my Pure and i've flashed it with dozens of roms. Since I was currently using one of the "Stock" AT&T roms posted on XDA I figured I could apply the updates. Unfortunately after applying the update my phone froze at the boot loader. I was forced to flash my rom using the memory card method and then restore a backup.
you could try putting the phone in SSPL mode manually, (reset button+volume down), the run hard-spl hard-spl in manual mode.
you can then flash your rom using the memory card method. (FAT32 formated memory card, rom file renamed to topaz.nbh copied to root of flash card, reset button+volume down to enter SSPL, power button to confirm flash).
All this assumes you've already tried to hard reset your Pure (reset button+vol up+vol down)
Thanks for the reply! Unfortunatly, i tried the manual method and after it hanging at 0% for about 5 minutes, i keep getting error [262] update error.. (communications error) is this becuase i can not sync with mobile device center (win7)? I really dont want to just have to toss the phone! I have had an at&t tilt, at&t fuze, and now the at&t pure, and this is the only phone i have had this problem with for some reason...
Try Unplugging Your Pure From the computer Take Out the Battery Put the Battery Back in Mean While Restart your computer and Press Power And Volume Down At the Same time on your Pure If its on the colored screen your good,..Make sure your system is online and your not downloading anything and plug in your Pure to the computer it give it about 2 minutes to download the HTC USB driver then once its done your phone will say USB on the bottom of the Red Green Blue And White four color screen Then open up one of your ROM's and Flash it,....Do You Have Windows Mobile Device Center Installed?
If Not here is the Link
http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
If you do already you need to uninstall the Driver update for windows mobile media center then install it again .
i can get the bootloader screen just fine! i just can not get hardspl to flash onto it. it sits at 0% every time. the phone will not boot so i can NOT get into mobile device center. The tri-colored screen comes up with no problem and it says USB on the bottom, so the drivers are already installed. I even tried hard-reset and still no luck
There was an additional cab file I needed to install to HSPL the Pure
"enablerapinew.cab"
basically the machine just would fail to load the HSPL without it
but it still functioned afterwards, does yours?
Do a search on XDA find and DL the cab (or I could attach a zipped copy)
If you can still access the device,
just copy enablerapinew.cab to any temp dir on the device
the execute it through fileexplorer
then go back to installing the HSPL (mine then worked fine)
If you haven't already, You should go to
http://forum.xda-developers.com/showthread.php?t=520312
you'll find troubleshooting info and a link to the extra cab there
If you really are bricked at this point , it sounds like nothing has actually
been changed on your device yet? its just frozen should be still under warrentee? Unless anyone else has a better suggestion you should be
able to return it for exchange to ATT
Good Luck
KJL
It sounds like Windows is not properly recognizing your device when it is plugged into the USB port while in SSPL mode.
Have you tried different ports?
Is there another computer you can use?
another thought about returning under warranty
on the boot page of the stock Pure it indicates HSPL 1.83.000
After you update the HSPL it will say HSPL "1.83.Olinex"
this normally an indication of a successful update,
but it will probably void your warranty if they just look at the boot screen
This is true for all Pure (and Tmobile Compact V) Rom upgrades
The Stock Pure came with 6.5 and therefore the 1.83.00 HSPL
The Diamond2s did not, so their solution which reverts to 1.63 <?>
will not correctly revert to 1.83.00 on the Pure.
No way to correct this yet as far as I know,?
All the "reverts" are geared toward the Diamond2s, not the Pure.
But If your boot screen indicates 1.83.00 before it freezes
I'm fairly sure its still entitled to a warranty repair/replace
How could they tell the cause of the failure
was a reburn as opposed to natural causes?
Good Luck
KJL
When you put the phone into a manual bootloader mode... Mobile Device Center becomes obsolete.
HardSPL is only needed for unofficial roms. Forget HardSPL for the time being. The goal here is to get your phone operational. Just download the official HTC WM6.5 WWE rom and flash that. Put phone in manual bootloader mode and run the Rom installer.
As long as your phone is in bootloader mode and says "USB"... then your set to go.
Another solution is to try another PC. You'd be surprised how often that will resolve your issues. Perhaps find an XP machine and install Activesync (so it loads the bootloader USB drivers). I had to do that on several occasions when my main PC refused to flash my mobile device.
I did both of the updates htc has for the pure. Both worked fine. I am on the origianal rom. It does reboot your phone and stays on the white screen for a min then it loads the update and the phone starts.
The offical ROM comes back with a wrong vender ID error I guess cause its a "pure" and not the HTC branded "topaz"... NOW what should i do??? Seems like i NEED hardspl so i can flash any ROM, as from what i researched, there IS NO AT&T Pure rom that has been released. I still cant figure out why a hard-reset will not work though.... This is REALLY starting to get me angry!!!
Just for reference, the Pure's ID is TOPA210 32M
SPL-1.83.0000
The official hotfixes worked fine for me as well. Did you apply the hotfixes on the original ROM that came with your Pure?
Also, does the official HTC Touch Diamond 2 ROM work for you? If so, the hotfixes for the Pure are irrelevant, as are any future updates released for the Pure. You should look for updates for the Touch Diamond 2 on the Worldwide HTC site.
If you needed to do a warranty claim, the closest you can get to returning your phone to stock/shipped form is to use the ROM dump using HardSPL and hope they don't notice that the SPL is different. Currently, there's no way to return the Pure back to completely official software.
A hard reset simply wipes everything off and restores everything back to what is contained in just the ROM you currently have on it. If you've flashed your phone at all, you've already wiped out the original ROM that came with it.
It is still the STOCK ROM. I have never flashed it yet.. The topaz rom will not flash due to a vender ID error. The spl is still stock also... i think thats is why i am having this problem. I bought the phone off craigslist so returning it to AT&T is NOT an option either way. My only solution is to find a fix. (or trash it) I really appreciate all of your suggestions and input so far. You guys are by far the best board around! I am a LONG time follower, but a few-time poster. Obviously i have little to contribute to the board.
Can I trouble you to dig up a few version numbers? It'd help evaluate your situation so we can see which options are best for your case.
ROM version? You can find this in Device Information. Start --> Settings --> System --> Device Information
Bootloader version? Do a soft reset while holding down the volume down button on the side until a screen with red, green, blue, and white, ordered top to bottom, shows up. It should be the second line starting with "SPL-..."
The ROM is the STOCK AT&T ROM (again...) I CAN NOT go to start;.... because if you noticed in the first post, the phone will not boot past the white "AT&T WorldPhone" screen... the spl is stock also incase you missed that part. (1.33.0000) I have never flashed the divice. EVERYTHING IS HOW AT&T SELLS THE PURE OUT OF THE BOX! NO MODS. NO FLASHED ROMS. NO HardSPL... NOTHING! STOCK!!! (for those overlooking the details in my previous posts) I have no doubt you guys (n hopefully a few girls ) will help me fix my issue. I'm just REALLY anxious for it to happen sooner than later!
Have you tried downloading the official rom here on xda and renaming it to TOPAIMG.nbh and update using the sd card method?
Here is the thread:
http://forum.xda-developers.com/showthread.php?t=600339
The download is in post #1
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
jromeo350 said:
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
Click to expand...
Click to collapse
You can flash hard SPL the same way by renaming the .nbh file to
TOPAIMG.nbh
jromeo350 said:
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
Click to expand...
Click to collapse
Actually that is supposed to be an officially signed rom. If that is true it will work with the stock spl. It will either work or it won't. Also, as stated in the response after yours, you can apply the hardspl via SD as well.

got hardspl now i'm stuck

a similar question has probably already been posted
i have a tmobile hd2
i successfully hardspl to it
i flashed the energy reference rom
then i realized that i needed to use the task29 tool before
i flash any rom... did that, hard resetted, and then tried flashing again (energy referecne) using the sd card method
and i just get stuck on the "NRG" screen
tried the other custom ruu method getting the same results
using the radio 2.07.50.27
i put back the regular spl to flash a stock rom but still no luck
i know the phone isn't bricked i can get to boot loader, hard reset
any help would be much appreciated
Thanks in advance!
Thanks!
lilguy227 said:
a similar question has probably already been posted
i have a tmobile hd2
i successfully hardspl to it
i flashed the energy reference rom
then i realized that i needed to use the task29 tool before
i flash any rom... did that, hard resetted, and then tried flashing again (energy referecne) using the sd card method
and i just get stuck on the "NRG" screen
tried the other custom ruu method getting the same results
using the radio 2.07.50.27
i put back the regular spl to flash a stock rom but still no luck
i know the phone isn't bricked i can get to boot loader, hard reset
any help would be much appreciated
Thanks in advance!
Thanks!
Click to expand...
Click to collapse
ok as from my knowledge you dont necessarily need to do task29 if its ur first time flashing (cuz i didnt and i got very good results) so i think u messed up in tht part.. but its ok, now you prolly want to first --> do a task29 again... second ---> get the nrg rom and flash it.... third -->get a radio of 2.10 or higher and flash tht....and just to play safe flash everything using custom ruu (i got better results using them...just saying)... also when u do each flash and its suspenseful dont boot up the phone, just take out the battery and back into bootloader.
hope this helps... report back lol
^thanks man
Okay so heres how it goes, my phone is def not bricked
custom ruu has only worked once for me
now whenever i try to use it it always gets stuck at 8%
i found that if i flash it at night and hard reset. wait til morning and turn on the phone
then it loads past the nrg screen and into the OS.
i'm currently trying to get it back to stock and i downloaded the tmobile update
but it doesnt seem to work, it also keeps stopping at 8%
i disable the anti virus stuff and i plug it in to the back of my computer
sounds like a defect
sorry to bust your bubble bro but it sounds like you got a classic case of a defective leo, i too did the same steps you did and it turns out my main board wasn't any good and the phone kept overheating, turns out when flashing custom roms they tend to put more pressure on the snapdragon then a regular stock t mobile rom. i know this sounds crazy but i believe it to be true, so with that said you got two options, one get back to t mobile customer care and get a replacement. or do what i did and find a repair shop and let them know that your leo either needs a new mainbaord or a new heatskin like mines did, it cost me 80 dollars which wasnt bad since my leo was a gift and i couldnt give it back to t mobile... hope that helps in some way
p.s. sorry for the edit but if you cant do either of those of what i suggested, try this get yourself a nice icepack nthe size of your phone and mount the leo on top of it whenever your using it, so that sucker wont overheat. once again i hope i helped

Categories

Resources