I have 2x HTC Universal's (Jasjar's to be precise) and 2x xv6700's that I'd like to pair, configure, and make work with the Delorme BT-20 (and Street Atlas USA Plus 2009) I purchased. As of right now I am having problems and I'm asking for help getting this done. I've never used a GPS on windows mobile before, so I'm not sure what info to offer up. Here's what I can think of that might be relevant:
Setup:
* I have successfully paired the BT-20 over bluetooth with 2 different laptops, both running xp-pro 32 bit.
* I have connected the BT-20 to 4 different laptops (the 2 above, plus two more) via USB, one of which has Vista Home Premium 32 bit and the other Windows 2000.
* I can connect over bluetooth with both of the JasJars to the PC I maintain my contacts on and sync with them. (so bluetooth works)
* I can connect over bluetooth with the xv6700x to the other bluetooth enabled laptop I use (for software downloads, and RemoteAmp use). (so bluetooth works)
Problems
* I can't confirm when and if the phone is connected to the GPS device. There is supposed to be LED feedback on the BT-20 when it is connected to a device over bluetooth (an LED that stays lit), which does indicate a connection on a laptop, but not on the WM devices I have tried.
* Initially I couldn't even get the device to pair to my Windows mobile devices. Today I was able to get it to pair to a JaJar with Tomal's most recent 6.1 build.
* Usually trying to pair the device was a game of cat and mouse, very similar to this:
"""I've tried every setup suggestion I’ve found on how to setup the “Earthmate BT-20 GPS” on my new Mogul. Anytime I enter a passcode of any kind I get the messagebox “Your device did not connect with Earthmate BT-20 GPS. The connection failed or the passcode is incorrect.” The blue light has stops blinking and goes dark. Subsequent attempts fail until the BT-20 is rebooted.
With the No passcode it ends with the blue light OFF, but get message “Earthmate BT-20 GPS wants to connect with your device using Bluetooth. Do you want to add Earthmate BT-20 GPS to your device list?” I answer YES and it prompts again for the passcode, this time the “Next” is disabled until something is entered. I enter the 0000 code and it fails again with “Your device did not connect with Earthmate BT-20 GPS. The connection failed or the passcode is incorrect.” After clicking ok it seems to still be trying to connect (spinning color thingie) but lets me through to the “Serial Port” selection, which I select and click “Finish”. """"
- http://forum.delorme.com/viewtopic.php?t=10886
* The Delorme software can see the virtual COM port that the windows GPS manager creates, but I get an immediate message saying that the phone cannot connect to the GPS.
* The Delorme software cannot see the hardware port that the GPS is assigned in the bluetooth management settings.
Misc notes
* There is an option to allow windows to middle manage the GPS connection. This sounds cool, and there are so few options, I imagine it should just work. The Delorme software can see the virtual COM port that this package creates, but I get an immediate message saying that the phone cannot connect to the GPS.
* I have tried to call Delorme Tech support. That was a monumental exercise in fail. The guy said that because I was able to connect over bluetooth to GPS device it was not bad and refused to send me a new one. And that is literally all he said. I take that back, he did say that there were no magic tricks to get it working, that it should just work. I did tell him that I tried 4 different phones.
* I have never used a GPS on a WM device, so its quite possible I'm making a n00b mistake. Please feel free to tell me if I am.
* I get the impression that this is so simple and its just supposed to work.
* I have re-installed it once after I configured the Windows GPS manager. That did not seem to affect the outcome of trying to connect to it.
* I was able to get the unit successfully connected over bluetooth only after removing the battery for about a minute or two. I found that trick online somewhere, and while it helped for the laptops, did not for the WM devices.
Other places I have looked:
http://forum.delorme.com/viewtopic.php?t=10886
http://blogs.msdn.com/windowsmobile/archive/2006/06/07/620387.aspx
http://www.delorme.com/support/Results.aspx
http://www.delorme.com/support/supporttemplate.aspx?id=313
Status update
I contacted Delorme Tech support. Over the phone was useless, but when I emailed them, I was issued an advance replacement (the email guy was pretty helpful).
However, that does not appear to have fixed the problem(s). It seems that the problem is in the communication settings of the phone, or the setup of either the phone of the software, or the bluetooth connection itself. I still cannot make the Delorme software find the COM port that windows makes for the unit, but the software will find the virtual COM port the windows GPS manager makes.
Any ideas out there?
Hi @ all,
just got my HD2 with german ROM and one of the first things I tried out was to get a connection to my car (Audi A6) through the remote sim access profile (SAP, rSAP) - but it didn't work...
Does someone use the HD2 in his car using the sim access profile, as available in Audi or VW cars?
I have
- Audi A6 Avant (model 03/2008)
- using the "Audi rSAP Adaptor" in the car cradle, located in the arm rest
- everything in the HD2 is activated for Sim Access
Result:
HD2 and car are connecting, I have to put the 16 digit security code in my phone, but after that the SAP mode does not start, and so I have no access to my phonebook. It seems that I only have a "normal" bluetooth handsfree connection, because the HD2 still shows that he is booked into the mobile network - and when rSAP is active, the phone itself disconnects from the network and "falls asleep".
I restarted my HD2 several times, also the rSAP-Adapter by turning ignition of the car off and on until the adaptor switches off, deleting the connections, creating new connections, but nothing helps...
Any comments or experiences from other users are highliy appreciated
Finally, I have to remark that my HTC Snap, which I just upgraded to WM 6.5, works very good im my car with the rSAP - no problems at all, I get all my contacts in the MMI.
Thanks in advance,
Jolig
Just got my HD2 and am having the same problem.
I'm trying to connect with a 2009MY Skoda Superb with the rSAP bluetooth kit.
This works fine with my E71 and my HTC Touch Cruise.
I've been told that there used to be an issue with OBEX authentication on previous versions of Windows Mobile. Apparently, it was important to disable this authentication. However, I can't see the checkbox in the version of WM that the HD2 is running.
Does anyone know what registry entry this checkbox might have been changing?
Thanks,
Bagpuss.
Thanks Bagpuss,
who gave you this information?
I hope someone can solve this problem....but I fear we have to wait until we have more HD2 - owners
-----------------------------------------------------
EDIT:
I just have read something about the "Schaps Advanced Configuration Tool" where someone with similar problems activated OBEX (but it was an older Win Mobile device, and some months ago) - perhaps this could help?
But I just installed version 3.3 of this tool, but it doesn't work on my HD2...
Hi Jolig,
Check out this thread:
http://briskoda.net/superb-ii/howto...us-rns510-using-non-compatible-mobile/131709/
on Briskoda.net.
One of the guys there had lots of problems getting his WM phone to work, and posted the fruits of his labours.
From what I can tell, we can't use the CAB file he mentions, as rSAP is built into the OS version that the HD2 uses.
I've actually logged this issue with HTC, and am awaiting their response. My company is considering the HD2 as our next standard handset, and we won't go for it unless the rSAP functionality works with all VW/Audi group cars.
I'll let you know if they get back to me.
Bagpuss.
Thx Bagpuss,
and yes, in my opinion it's a mess that the rSAP is apparently VERY unimportant for most people or manufacturers...otherwise we wouldn't have this trouble....
I will come back too if I should find some news.
Had the same problem, tried lots of stuff but none of my WM devices is able to work with the rSap protocol. Gave up on it and then my Skoda Columbus system was stolen.
Replaced it with a JVC 7000 with detachable front. Disabled the rSap carkit and am now using the JVC BT carkit wich is working great. The problem is in the MS BT stack. It is not supporting the rSap the way it should. Only phones that work flawlessly are Nokia's I'm afraid...
The lack of rSAP support is what made me ignore the iPhone this time around.
I was hoping that the HD2 would be a viable alternative, but sadly, it doesn't look like this is going to be the case.
As I bought it over the phone, then I've got 7 days in which to return it. If I can't get it to work, then I guess I'll be getting an N97 or N97 Mini (which will definitely work). :-(
Bagpuss.
@ Bagpuss,
otherwise, as I wrote, I can recommend trying the small HTC Snap (or also called Maple?).
Ok, this one has no touch screen and also a very small screen - but I can confirm he works with rSAP and is not too expensive. I will keep this one, although I now have the HD2
As to Bagpuss' information concerning the OBEX, I tried the following:
- installed the newest .NET framework version
(that was necessary to get Advanced Config Tool v 3.3 running)
- install Schap's Advanced Config Tool
- in the menu "Bluetooth", I enabled OBEX
- after that the config tool does a soft reset
...still no success....no SAP and no phone book
I also wrote an email to HTC - it's really annoying, having SAP in the phone etc. and nothing works.
I've a Golf VI (RNS510) and it's working very well. Just had to change Bluetooth security settings that by default does not make HD2 visible to other devices. And after partnership was established, I've reverted the settings to "Allow only devices from MyDevices to connect"
Hi Binks821,
Binks821 said:
I've a Golf VI (RNS510) and it's working very well. Just had to change Bluetooth security settings that by default does not make HD2 visible to other devices. And after partnership was established, I've reverted the settings to "Allow only devices from MyDevices to connect"
Click to expand...
Click to collapse
Can you confirm if your Golf has the premium bluetooth preparation?
There are two different versions of factory bluetooth kit for the RNS510, one which simply acts as a handsfree device, and the other (premium) which is a complete GSM phone.
It's the premium kit which uses rSAP, and which seems to be incompatible with the HD2.
You can tell if your Golf is using rSAP by checking to see if the signal strength meter on the HD2 shows any bars when connected to the car. If it does, then it's not using rSAP. If you see the signal meter with a little x in the corner, then it is using rSAP.
If you do have rSAP working, then I'd really like to know which firmware version your RNS510 is running, and also which firmware version you have in your HD2.
Thanks,
Bagpuss.
yes I've the premium version with RSAP access, not just handset.
Once partnership is established, it says SIM Access profile in Bluetooth settings, not Handset. And it disables my SIM on the phone, so no strength meter.
I had a Tytn before, and it was working the same way. Just when received my HD2 Monday, it was not working but default settings on the phone make HD2 not visible, So I received a message on the car saying "No compatible phone found". After playing with Bluetooth security settings, it was OK.
And of course I can import SIM contacts.
Be sure to check these settings (Settings tab in Sense, then Menu-> All Settings -> Bluetooth)
- Discoverable: always visible
- Advanced -> Connectivity: Allow all devices to connect, just during setup. After that change to "Allow only devices listed in My Devices to connect"
- Advanced -> SIM Access: be sure that rSAP is enabled
HD2 version info:
- OS: 5.2.21864 (21864.5.0.81)
- Manila: 2.5.19202525.0
For the car I have to check once I'll be in.
Hi Binks281,
Thanks for the confirmation.
I've now done some further testing in my car, and managed to have some success.
This is what I did.
In the car:
1) Remove all device pairings from the bluetooth system in the car.
On the HD2:
1) Perform a hard reset.
2) Turn on bluetooth. Make HD2 permanently discoverable.
3) Make sure rSAP is enabled (it is by default).
4) Turn off SIM pin (turns out this isn't necessary, but I wanted to make things simple).
So, at this point, I have the car system with no paired phones, and the HD2 with factory settings and no personal data (contacts etc.). I also made sure there were no contacts on the SIM card.
Back in the car, I perform a device search, and it detects the HD2.
I select the HD2, and the car displays the pairing password (1111 2222 3333 4444).
On the HD2, I enter the password.
I then get a prompt saying that Skoda_rSAP is trying to connect to the remote sim access service. I say allow, and also tick the box to allow all future connections.
After about 10 seconds, the maxidot in the car says 'New SIM card recognised', and prompts me to create a new user profile. I called it 'HTC_HD2'.
After about another 15-20 seconds, the car should extract the SIM details from the phone and the phone name, network and signal bars should appear in the car display.
You can now make calls, but there is no phonebook.
Given what others have said about the phonebook access, I'm pretty sure that this is what was stopping the pairing from working the first time I tried it. I've heard various stories, some which say that the phonebook access only works with SIM card contacts, some which say it only works with OBEX authentication switched off and so on.
If you look at the paired devices screen in the phone, then you can see connections coming into phone. First, you see a connection to the SIM Access profile, followed by a brief connection to the Phone Book Access profile. It was at this point, when accessing the phone book, that my previous attempts to pair failed.
I'm still trying to work out what is causing the problem with the phone, but I have done the following things:
1) Told the car to only sync phone memory contacts. By default, it's set to sync both SIM and phone memory. You can configure this on the car by going to Settings -> Phonebook -> Select Memory, and choosing 'Mobile Phone'.
2) Created four contacts in phone memory, one with only 1 mobile number, one with 2 numbers (mobile and home) and another two with three numbers (mobile, home and work). I've then gone into Settings -> Phonebook -> Upload and sync these across to the car.
So far, this has worked fine and disconnecting and reconnecting to the car works without a hitch.
I'm now going to try syncing a small subset of my contacts with ActiveSync to see if this also works.
If it does, then I'll gradually increase the number until it either works, or fails.
I'll report my progress here.
Bagpuss.
Thanks Bagpuss,
sounds interesting!
I think tomorrow I will try this also:
- remove all paired phones in the car-system
- delete all contacts
- disable SIM Pin
Temporarily I am not sure if I will do a hart reset in the first step because I've already installed so much... When the work fails, I thing I must do it
I will report what happened.
---------------------------
EDIT:
Ah, come on...TV this evening nothing interesting, wife in bed...I tried it, including hardreset
No success.
Bagpuss, what I detected:
First, you see a connection to the SIM Access profile, followed by a brief connection to the Phone Book Access profile. It was at this point, when accessing the phone book, that my previous attempts to pair failed.
Click to expand...
Click to collapse
This connection to the Sim Access Profile I see also, but only for one second, then it dissappears and then the connection "Handsfree" comes up - and this one remains....
I do not know else what to do.
I now reconnected my beloved HTC Snap/Maple, and now I will start installing my apps on the HD2....
Hi Jolig,
Sorry to hear that it didn't work.
By the sounds of it, the Audi system is somewhat different to the VW/Skoda one. From what I can tell, your system also appears to support using phones in handsfree mode (I'm guessing that the iPhone works in your car).
In the VW/Skoda cars, you can either have a car kit that acts as a handsfree device or one that uses rSAP, but not both.
It could just be that the HD2 isn't responding to the rSAP request quickly enough to satisfy the MMI. In that event, it falls back to using handsfree mode.
When it shows 'handsfree' on the HD2, can you use the MMI to make calls?
This whole area seems to be a bit flaky on the HD2, as I still can't work out why mine didn't work when I first tried.
Bagpuss.
Binks821 said:
yes I've the premium version with RSAP access, not just handset.
Once partnership is established, it says SIM Access profile in Bluetooth settings, not Handset. And it disables my SIM on the phone, so no strength meter.
I had a Tytn before, and it was working the same way. Just when received my HD2 Monday, it was not working but default settings on the phone make HD2 not visible, So I received a message on the car saying "No compatible phone found". After playing with Bluetooth security settings, it was OK.
And of course I can import SIM contacts.
Be sure to check these settings (Settings tab in Sense, then Menu-> All Settings -> Bluetooth)
- Discoverable: always visible
- Advanced -> Connectivity: Allow all devices to connect, just during setup. After that change to "Allow only devices listed in My Devices to connect"
- Advanced -> SIM Access: be sure that rSAP is enabled
HD2 version info:
- OS: 5.2.21864 (21864.5.0.81)
- Manila: 2.5.19202525.0
For the car I have to check once I'll be in.
Click to expand...
Click to collapse
Hello Binks821,
I believe that I have the same hardware situation like you but I can't get my HD2 started on my VW Passat with the Premium FSE. The problem is, that I can go through the whole "finding and connecting process" and can save the PIN but then the Connection gets lost between the HD2 and the PFSE. If seems that the PFSE can't connect to the Network (E-Plus) but why the BT-Connect gets lost in this case.
Maybe you can help me to get it work. Thanks a lot!
Negropo
Hello everybody,
maybe I found a solution that work for every sap-handsfree-set. I tried the hint was given on the german car forum "motor-talk" for the connection problem between a vw pfse and the htc touch diamond with wm 6.1 or 6.5.
The trick is that you have to disconnect the HD2 from the pfse by manual when the car first want's to connect automatically. You have to go to the BT-Setup to the tab where are the connected devices listed. If you click on the "+" right of the name of the device you should be seen the tab "Remote Sim Access" or in german "Sim-Zugriff". When the car connect's to the HD2you have to stop this by pressing disconnect in the right below corner of the HD2 screen. Then the connection is terminated. Now you have to start the connection manual over the menu in your car. In a VW you have to press only "connect" in the MFA. And then the HD2 should connect without problems. I don't know why it works but it does. Maybe there is someone here who can explain it and find another "automatic" solution for this problem.
Regards Norman
Well, I don't have a VW but an Audi with an rSAP-Adaptor in the middle arm rest. I fear this also doesn't work for me.
The problem is that this Tab "Sim Access" only appears for just one second, so I have no chance to make anything whithin this single second....and after disppearing of the tab "sim access" another tab "handsfree" appears - and stays. So it seems my Audi only recognizes a handsfree profile. I don't know why,
Temporarily I am happy that I still have my HTC Snap, which is working very fine with rSAP
@ Negropo, can you tell me in which thread at motor-talk you found that?
Thanks,
Jolig
Hi guys,
rSAP works fine with my Audi A4 BTA. I made the HD2 discoverable for any device and I activated the SIM access in the HD2 BT settings. Then I start searching for Bt device on my Audi BT and initiated the connection with the HD2.After inserting the 16 character pin everything works fine.
By the way ... the connections seems to be very stable. With the Touch Diamond I had from time to time connection interrupts where it was necessary to reset/restart the Touch Diamond again.
Best regards,
Matthias
@ Matthias,
"BTA" means that you have the built-in phone with rSAP, right? Is it a brandnew A4?
There are some very old threads about this - but this is now, pretty certainly, a general stock android 4.3/4 problem with "older" car hands-free systems. My kit is a Galaxy Note with OmniROM right up to date. My car is an Opel/Vauxhall Zaphira with a Navi 900 onboard computer. However there are threads on many android forums complaining of the same symptoms for "pure" stock 4.3/4 devices (e.g. the Nexus range, including the Samsung Galaxy Nexus) and a variety of cars, and all describing the same workaround (and a few lamenting that Google haven't been very responsive in addressing the problem). The symptoms and workaround are:
The car recognizes and "partially" pairs with the phone
However, the contacts list and call lists are empty and the phone cannot be controlled from the car, neither for incoming calls nor for outgoing calls (dialing from the car interface always gives a failed message, while trying to receive or hangup from the interface just plain fails).
Calls using the phone work, and show up on the car interface, always as "Unknown" (not surprisingly - it doesn't have the contacts list)
HOWEVER if, after this "partial" pairing up, I make a 30-45 second call using just the phone itself, then, after the call has terminated, contacts and call lists are properly available through the car interface and the phone can be fully controlled from that interface (and, of course, the FIRST time this happens, I get the notification on the phone telling me the car wants this information, which, of course, I confirm)
A workaround like that can be scripted with something like "Tasker" and using, say, my voice mail number (with my provider here in France, plain fake number calls don't stay online long enough for the above to work).
But does ANYONE have any idea where to start looking for the root cause and possible solutions, or have any theories on those points?
EDIT:
Just to be clear - the workaround "make a call from the phone" trick has to be done every time the phone and car reconnect, not just the first time.
Had this happen in my ford the other day and it's sync system.
The fix for me was a not so visible notification upon establishing the Bluetooth pairing in the notification tray asking if I wanted to allow for my phonebook to be downloaded. Clicked yes and everything set up as normal.
Mgd_toronto said:
Had this happen in my ford the other day and it's sync system.
The fix for me was a not so visible notification upon establishing the Bluetooth pairing in the notification tray asking if I wanted to allow for my phonebook to be downloaded. Clicked yes and everything set up as normal.
Click to expand...
Click to collapse
I got that notification AFTER I had done the "make a call from the phone" trick, not before.
I should also point out that the "make a call from the phone" trick has to be done every time I want to reconnect to the phone to the car (while the notification only appeared the first time I did the trick - because subsequently the phone and the car "trust" each other).
Aside from maybe unpairing and trying to set it up again which I am certain something you've probably already tried; have you checked the cars firmware?
Could also try resetting your Vauxhall's system as well in case there is a gremlin in there causing a hang up with the sync.
Again with Fords sync I have had to do it a few times over the years when the systems been misbehaving with the Bluetooth and it fixed it.
Mgd_toronto said:
Aside from maybe unpairing and trying to set it up again which I am certain something you've probably already tried; have you checked the cars firmware?
Could also try resetting your Vauxhall's system as well in case there is a gremlin in there causing a hang up with the sync.
Again with Fords sync I have had to do it a few times over the years when the systems been misbehaving with the Bluetooth and it fixed it.
Click to expand...
Click to collapse
Indeed I did the resets. And yes, possibly, an upgrade of firmware MIGHT fix it, but these problems don't occur with Android 4.1.n (or, I, believe 4.2.n).
I've logged a bug with the OminROM developers, but would like some pointers so I myself can start looking at solutions and fixes.
Hmm... Unfortunately I don't know who to assign that JIRA bug to.
Problem is - none of us own vehicle headunits that we can reproduce/test this problem on. I used to have a Sony MEX-BT2500 (technically I still do...) but since I sold my old convertible it just sits and collects dust.
I would agree that this will be a difficult one to find. It reminds me of working with 802.11b/g with it's dozens of "pre-draft" variants that just didn't interoperate properly.
If you wanted to dig into this yourself, the first place I'd look is https://github.com/omnirom/android_external_bluetooth_bluedroid and its upstream and parallel variants. That is the code that generally handles the upper-level Bluetooth management functions.
Edit -- Also worth looking at https://source.android.com/devices/bluetooth.html if you want an overview of how Android implements Bluetooth.
The comments on commits there might also be worth reading through. For example
https://github.com/omnirom/android_...mmit/73ce8ab2ddd30cab6499d0062c46b3a16f9130a9
Fact is however, that the use of SDP features value for peer_features
is new since Android 4.2 and breaks existing good behavior on a BMW
2005/E46 car kit (navi professional). This kit never asks for AT+CHLD
and never via AT commands suggests it supports 3WAY (although it seems
to have the flag set via SDP).
Not the same issue, but there might be clues of that nature in the commit messages.
Hello everyone, I bought a new 2015 Jeep Cherokee Trailhawk, it has the 8.4N Uconnect system installed.
I can connect with bluetooth with any other devices, and everything works properly....EXCEPT my phone which is a:
Samsung Galaxy S4
Branded by Fido in Canada
It is rooted, still using the default rom that came with it, but I'm running Nova Settings instead of Touchwiz
SGH-I337M
Android 4.4.2
-----------------------------------------------------------------------------------------------------------------------------------------------
In my car, I goto Phone/Bluetooth settings, have option to change PIN to anything I like but left it at '0000'
On my phone I goto Bluetooth, turn it on, make it visible, hit scan......it finds UCONNECT
I press on it to connect and THEN.......
On the car:
if it is the first time trying since reboot, you can see the passcode show up (six digits - 3 digits a space and then 3 more) and an ACCEPT button. This immediately disappears and it says 'There was a problem connecting with your bluetooth device. Please try again'
If it is not the first attempt after a reboot of phone, it just blinks that first screen showing the weird seperated 6 digit pin and immediatley goes to the error messager.
On the phone:
When it finds UCONNECT and u choose it, a message pops up saying to confirm the passkey and press OK or CANCEL.
It always shows a random 6 digit number.
At the same time, a system message appears for a couple seconds at the bottom of the phone that says 'Incorrect PIN or Passkey. Please try again'
Pressing OK or CANCEL just returns you to the bluetooth scanning screen which shows UCONNECT as an option.
If i try to set the pin on the car with what was shown in the phone, it doesn't work as each attempt to connect generates a random pin on the phone.
I have restarted phone, car etc. Reset car radio completely. Removed all devices remembered on the phones bluetooth. Checked with UConnect support that my phone is compatible -- they say that it might be that Fido in Canada has done something to the phone to prevent it to connect to cars, as it works fine with Verizon/At&T/ and apparently people on Rogers in Canada with S4 works too.
I have commented out the blacklist entries on the phone in /etc/bluetooth/auto_pair_devlist.conf - no change
I have removed all files in /etc/bluetooth - no change
Other phones connect to Uconnect with no problems.
My phone connect to my TV and a bluetooth receiver connected to my home stereo and a second TV different brand no problems.
This is my main phone, also my new car. It really sucks that I cannot get it to pair. Fido, Uconnect support can't help - they have never seen this issue before.
I don't understand why the car shows a pin of six digits with the space between the two groups of 3.
Also, why the phone says incorrect pin or passkey.
PLEASE HELP!! I am going crazy over this!
I really don't want to, but if there is no fix, I will have to backup everything, format the phone, install perhaps a Verizon or something build of Android and then try to connect with that (hoping it has no issues with phone/data use with Fido network over here)
Updated info
I just tested with anothers car....
2009 Nissan Rogue...works fine (is used as an audio device only...no phonebook etc features)
Also tested with an Iphone 5 to my Jeep and that phone connects fine.
I tried using an app called 'Bluetooth Fix Repair' from the app store. It gives an error at startup:
"Sorry this application cannot find your bluetooth setup folder on this device"
Can this be the issue?
The bluetooth folder I was working with in the OP was on the phone at etc/bluetooth
Should I have another one somewhere...maybe missing or corrupted?
Any help!?! Cannot find anyone else with this same issue here (xda) or on google etc.