Database Users

Problems!!

If i want to upgrade my wallaby i get an error message in the communications procedure. I have downloaded my ROM from lumpy's kitchen and ive tried to upgrade it many times right now.
Can anyone give me an advise how i could hardflash the ROM of my device?

I think you get an communication error when trying to flash via ActiveSync.
You have to flash via bootloader....
http://wiki.xda-developers.com/index.php?pagename=Wallaby
Here you get furthe rinformation about how to do it....
HTH
Stefan

Nothing yet
Ive tried to Bootload te rom, but after the message "connect your USB now" the device does not react anymore.
I have tried to run the application rom but this says that active sync does not recognize a device.
What should i do next?
Thanks for the quick respond!!

Even if i make a bacup to SD this doesnt work. There no explaination how to hard flash the device! Can you give me an advise???

What have you done exatcly, and where is the problem?
It's not really clear for me.
For Flashing via SD-Card there is no USB connection necessary....
STefan

I have tried to flash with the bootloader. When i push on the on/off putton and do soft reset i see the question "connect to USB now". If i connect and i start the rom nothing happens.
Afterwards i have tried to put the rom on my SD card. I have tried to do this OSimagetools. The pc does recognize the SD card in my wallaby. I also dont have a cardreader.
Is there a way to flash my wallaby in the bootloader-mode with the USB connection?
What do i have to do for it?
Thanks

Strange.
You should see device displays a background that consists of four equally sized vertical bars, colored (from top to bottom) white, red, green and blue. On top of this, it says:
WALLABY
Bootloader
V5.14
WAIT
After a few seconds, the WAIT is replaced by GSM OK. Both messages are in the blue bar, but have a white background.
What do you get?
What is labeld on your rear sticker of the device? (modell) ?
Stefan

Its model: PW10A1
SN: HT220cc15300
PN: 99HJ00007-00
Step 1)I have seen the horizontal bars. And its version 5.18. Ive also seen the "GSM OK"- notification.
Step1a)If i connect it afterwards to my USB nothing happens. The computer does not recognize the Wallaby.
Step2) If i hold the On/Off button i get the message "Connect to USB now" If i do this, activesync does recognize my device and i cannot install the ROM.
Step3) after step 1 i press the contacts button and i see 6 ways to backup my rom or GSM. I have backedup my GSM and ROM to SD. But this has no use for me.
Greetz,

Ok. Now I see.....
First of all, you have an totaly unknown Bootloader (5.18) to me, so i hope all steps will work....
You require a SD-Card with >= 64 MB
XDATools ftp://[email protected]/Wallaby/Tools/XDATools.zip
Your downloaded ROM from my kitchen
step1) Boot your XDA up normal and connect via active sync (guest partnership is ok)
step2) Copy all your data of your sd-Card to your local PC otherwise all data on it will be gone
step3) Enter bootloader of your device by pressing On/Off and doing a softreset
step4) After the Message GSM OK press the Contact Button of your device
step5) Navigate with the pad to "CE+BOOT TO SD"
step6) Confirm this with the Action Key (Press the middle of the Navigate-Pad)
step7) After finishing enter again bootloader by holding On/Off and doing a soft reset
step8) Bootloader should tell you something tah OS is detected on your SD-Card
If No -> Problem
If Yes -> continue
step9) Boot your XDA up normal and connect via active sync (guest partnership is ok)
step10) Install XDATools on your PC
step11) in a dos -box (cmd) go to the directoy where osimagetool is located
step12) enter command: "osimagetool -r xdasdslot -w original.nbf"
step13) enter command: "osimagetool --register"
step14) extract the downloaded ROM using winzip
step15) Run osimagetool
step16) Select the nbf-file in the english-folder of the extracted lROM as source and XDASlot as destination
step17) After finishing enter again bootloader by holding On/Off and doing a soft reset
step18) Bootloader should tell you something tah OS is detected on your SD-Card
step19) Press Action Key to install the ROM
step20) After finishing do a hard reset
step21) Now your ROM should be installed on your device.
step22) Locate the created file original.nbf and compress it using winzip
step23) Upload the compressed file to ftp://xdaupload:[email protected]/Wallaby/Uploads
step24) Enjoy your new ROM
That should be alll .....
;-)
HTH
Stefan

Thanks, But when i extract the rom to a folder, OS Imagetools cannot find the nbf-file. There is no nbf-file in the extracter-rom-folder. I can only find an nb-file.
There is a file called "NK" which says that its an NBF-file(properties). The file is 32MB large. I have tried to select this file (step 16), but the file is not being recognized. Even if i change the extension of the filename. The OSimage does not support this file.
I Have tried this with 3 ROM's : 2003 SE, 2003 and 2002 neither of them contain the nbf-file in the english folder.
Do you have an advice? I think i am very close right now!!
Thanks,

I have sucseeded to install 2002, but 2003 SE wont be recognized. It says its an usupported file.
Has this anyting to do with the fact that i renamed the file? If so can you tell me how to change the file back??
I have downgraded my wallaby to PPC 2002 right now.
Thanks Lumpi!!

WM2003SE couls only be installed via Exe-File. It can not be flashed with the osimagetool.
Stefan

Noob here! - Bit of advice

Guys,
I have a standard O2 Orbit here and I am looking at installing this TouchFLO ROM I've seen on this forum. However I'm a bit worried about bricking my phone.
Can somebody just give me a few steps to follow. I've searched but I have to say I got a bit confused when reading about CID locks etc...
Any help greatly appreciated.

You have to run USPL first (USPL by "Pof")
You will find it at STICKY Section.
Mostly all the ROM here lately allready built in USPL. so it will automatically takes you to the next DSUU windows.
but if you really wants Step by Step:
-----------------------------------
1. Make sure your Activesync is version 4.5 (or Above).
2. Refresh your PC by "RESTART" and enter WindowsXP again (just to make sure your PC running fresh).
3. Refresh your PDA by "Soft reset" your PDA, wait until finish (just to make sure your PC running fresh).
4. Make sure you have 80% or more Battery.
5. Connect your device to PC via activesync using USB only.
6. wait until "connected" or "Syncronized".
7. Enter folder USPL.
8. Double click "start_uspl.exe" (small yellow ball icon).
9. Black screen will appears... start uploading 10%..20%.... until 100%
10. Update windows will appear... Follow instruction by clicking "NEXT" or tick "YES I AGREE..bla bla" check box.
11. The progress bar will appear... wait until Finish.
12. Do not unplug the USB cable or your PDA become brick.
13. When finish your PDA Restart itself... and normally enter the today screen.
14. If not working try it again from Step: 5 (sometimes need to try more than one)
13. If your PDA restart itself and Show the SPL number is changes then CONGRATULATIONS you have finish install the USPL.
Next step is to Upgrade your ROM using DSUU (its on the ROM folder)
14. install DSUU is simple just double click "ROMUpdateUtility.exe"
15. Update windows will appear & follow instructions.
I Hope it helps..
best regards,
Wens

I'm assuming it won't differ if I'm using Vista as my client and not Win XP?

Also, is it possible to do this Via Bluetooth as my bloody USB cable isn't working correctly!

Vista not using Activesync, but WDMC
you can download at microsoft Website.
Upgrade ROM only can be done using USB cable. other won't work.
Good Luck!

- Install Windows Mobile Device Center 6 for Windows Vista
- On your artemis launch Bootloader and connect with your PC using usb cable. (For bootloader press Voice Dial + On/off button at the same time till you see a multi colored screen)
- Do exactly what the tutorial describe here: http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
- Your driver is changed so you can cid unlock your artemis now, do this by using USPL. (download below + manual). Remember to use the same usb port where you changed the driver from, otherwise the connection get lost and you have a update error.
- You can now search for a cooked rom of your choice and simply flash it by running the RUU.exe.

I did Slider's
...I followed the instructions but after step 9
(9. Black screen will appears... start uploading 10%..20%.... until 100%) nothing happened on my phone.
Any ideas. No "Next" or anything...the update rom utility just fired off (running the USPL from the Touch Rom directory

the prob seems to be vista......
or it could be the o2 offical WM6 rom
mine will upload the offical O2 rom but everything else fails.
people tell me im doing it wrong but have followed the driver swap step by step on 2 diff vista machines with no joy.

just borrow somebodyelse Windows XP Machines.. that'll do.

spv m2000 help

Hello, I have a spv m2000.
I try to instal windows mobile 6.1 on spv m2000, but i can't connect BA to pc in Bootloader mode with windows vista. I try all metods that are describle in ( http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4_Vista ), but i haven't success.
But now, when i turn on device, i see that i loose many programs (PVPlayer, Album, WESTTEK Native Office Viewers and Orange configurations).
how can I return to these programs?
sorry my bad english, but english isn't my motherlanguage.
regards

Well
I dont have vista but in bootloader you dont need to sync it you just need the drivers... maybe your WMDC is not updated... check it out...

I have WMDC version 6.1.6965 and I install drivers for my vista 32bits

can you xplain it?
So... can you xplain where did you get stucked?
maybe the error that the RUU shows you?
or what else... has happening to your device please?
Edit: Xplain all detail please... to see if anybody can help here...
or you just need a XP pc... is suggested to everybody here.

whell, i follow step by step the tutorial.
1. I install xda-developers_Unlocker.CAB
2. Then go to start -> Programs -> ExtROM tools -> then first run "unhide", then "Unlock".
3. Do a soft reset.
4. Once your BA is restarted, locate the Repart_DOC.exe file with your filemanager and start it.
5. Set the size of Extended ROM to 128 kb (which is already the default).
7. I press "format now!"
8. Soft reset your BA.
after I download vista 32 bits (driver)
9. Extract the contents to a folder on your desktop, to "AS_DRIVERS" folder.
10. I put your device into Bootloader mode by pressing and hold the "Power" & "Record" buttons, and then press the Reset Button.
11. Connect the phone to the sync cable/cradle USB;
12. Now navigate into the WMDC (Start -> All Programs -> Windows Mobile Device Center)
* Click on the "connection settings" menu icon
* In the connection settings menu uncheck "allow USB connections" then press OK.
* Now exit the WMDC and return to the desktop
13. Go into the start menu and type "Services", this will take you into the local services dialogue and show a list of all services either running or registered with your pc.
* Scroll down the list and make sure these services are present:
* Windows Mobile-based connectivity
* Windows Mobile 2003-based connectivity
* If these services are not started then double click each one and set them to Automatic start by clicking the "startup-type" drop-down menu and selecting automatic then click the start button in the same window, apply the setting by pressing OK.
* Return back to the desktop again
14. Go into the start menu and type "Device Manager" then run, this will take you into the device manager.
* Click the "+" symbol next to "Mobile Devices" and double click on "HTC USB Sync".
* This will bring up the properties of the currently connected device.
* Go to the "Driver" tab and click "Update Driver".
* Click "Browse My Computer for Driver Software".
* Select "Let me pick from a list...."
* Click the "Have Disk" button.
* Click "Browse" and navigate to the AS_DRIVERS folder we created earlier.
*
Now select your file
o Vista 32bit users select the file "wceusbsh.inf"
o Vista 64bit users select the file "wceusbshx64.inf"
* Then click Open.
* Click next and the driver will be installed (wait a moment).
* Press close and escape back to the desktop now.
---» In this step that i have problems
9. Now we must stop the WMDC process
* Start the task manager by pressing Ctrl+Shift+Escape.
* Click the WMDC line and click "End Process". In the confirmation window, again press End Process.
* Now re-enter the WMDC and re-enable USB connections (click connection settings and check the box "enable USB connections").
my BA doesn't appears in WMDC, i don't have any conection with BA in bootloader mode

I thinks that problem is in extRom.
The BA cannot instalt the extRom program

[Q] i need wm 6.5 os

hi
my name is shekhar
please get me wm 6.5 to my htc diamond
i want to upgrade from wm6.1 to wm 6.5
please

How to Install or Update your Windows Mobile?
Please Follow Below Orders :
Please Follow Below Orders :
1. you need a PC
2-1. If you have Windows XP -> Setup ActiveSync 4.5 from Here
2-2. If you have Windows Vista or 7 -> Setup Windows Mobile Device Center from Here
3.If you use manufactured ROM(Orginal WM6.1 ROM OR Official ROM) -> Install Touch_Diamond_-HardSPL_OILNEX From Here
How To Install HardSPL on Touch Diamond?
-> After Downloading and Extracting this file
you Must connect your Touch Diamond to your PC with its Cable
Let your PC Connect to your PPC with ActiveSync or Windows Mobile Device Center
Find HardSPL Folder and Run ROMUpdateUtility.exe
At Appeared Windows Page By ROMUpdateUtility.exe Accept Check Box and Click Next Button
Warning : Don't Unplug in Touch Diamond's Cable , Diamond's Battery Must be Charged More than 50%
Then you can see this Message on your PC->"verify the information on your PDAphone...Please wait"
After That you can see Setup Page on your PPC with 4 colors and on the White Color Part ,you can see USB (Notice : You can See Setup Page with Holding Sound Decreasing Button and Pressing Restart Button togather and Release Sound Decreasing Button Until Appearing That Screen)
Clicking Update Button And Next Button After That
And in Finally you can See Two Process Bars are Processing in the Same Time One of them on your PC and Another on your PPC and Restart your Device automatically.
I congratulate, your Touch Diamond Has Been Unlocked now you can install any ROMS That you Want
4. Downloading WINDOW MOBILE 6.5 WITH HTC SENSE 2.5 from Here ( you can See its Pic Here)And Extract this file
5. you Have this folder With two Files CustomRUU.exe And a File With NBH suffix , IF this Folder Dosn't have CustomRUU.exe Download it from Here And Put it to this Folder
5. Run CustomRUU.exe -> Keep Clicking Check Box Button and Next Button until Appearing That Message Again : "verify the information on your PDAphone...Please wait"
6. Clicking Update Button And Next Button After That
7. you can see again Two Process Bars are Processing at the Same Time On your PC and PPC
8. After Finishing ->your PPC Restarts Automatically Again And you Have WM6.5+HTC SENSE 2.5 ON YOUR TOUCH DIAMOND
9. Enjoy. (This ROM Has Been Made And Cooked by donsalari So Much Fast and Stable and Also Really Nice)

Hi guyz!
I have heard it said some of the ROM updates cause some technical failure...like GPS failure or G-sensor....
I wanna ask someone, who have tried this ROM if its ok and will not make any defection!
Thanks in advance!

workes great

ROM Hw6945 Windows Mobile 6.1

Hey guys, I found how to upgrade the HP 6945 in a brazilian website and I tried, IT WORKS! I'll explain how to do so now that I can post URLs
First of all, and which is a bit difficult nowadays, you need to use Windows XP, I saw cases that the people have done the upgrade in a virtual machine, but it didn't worked for me.
Let's go to the specifications of your mobile: your Flash Type MUST BE G4 and your BootLoader MUST BE G.39 , if you don't know you can see that in your mobile "Start/System/HP Asset Viewer"
Let's start,
1. Connect your mobile by ActiveSync (you'll need the 4.1 version as your mobile is WM5) using the cradle/dock/usb (was recommended to do a Hard Reset, but it's optional. To do so press On/Off , Send and Cancel Calls buttons, then use the PEN (Stylus) to press the Reset button under the mobile)
ActiveSync 4.1 - http://www.mediafire.com/?blql91lb1cqfq5z
2. Download and extract the file "SPL vG.39.7z" - http://www.mediafire.com/?o243pua8x7c0j0h
3. In the "SPL vG.39" folder, look for a shortcut named as "Command Prompt" and execute it
4. Now write this line in the command:
pdocwrite spl -n0 -b 0x20000 0 0x80000
5. You'll receive in your mobile a message about a dll (itsutils.dll) Press YES.
6. Now you have to put your mobile in BootLoader mode. Press the two buttons next to the directional + On/Off + Reset (using the Pen[Stylus])
7. Now open the ActiveSync and go to "connection configurations". Deselect the box "Allow USB Connections".
8. Download and extract the file "6915_ENG.7z" - http://www.mediafire.com/?kgwl83e22e2oody
9. Open the folder and execute "Sable_RUU.exe"
10. Press Upgrade and WAIT for a message "Update finished!"
11. Go back to ActiveSync (now you should use the 4.5 Version), go to "connection configurations" and select "Allow USB Connections"
12. Enjoy.
Everything is working, and you now have a new Office Package, including OneNote.
Your calls are better, don't freezing. The only problem is that SMS don't do any sounds when it arrives, but it's just the SMS.
The bluetooth you'll need to go to the Settings/Connections for the first time to work, but it's just once.
I have all the downloable content, if the link don't work, email me.
The original Rom of your iPAQ you can be found at HP's website named as GSM Radio Firmware, if you want, but I don't mind you'll need it.
The original website is in Brazilian-Portuguese, I've just translated for you.
http://www.gsmfans.com.br/index.php?topic=202365.0
That's everything. =)