Hello,
I installed WM6 this morning, and it works, more or less, properly. Now I downloaded the Ext-ROM tools and the Repart_DOC application. After I launched the "unhide" (without a message) and then "unlock", I get the message:
"ERROR: FL_IOCTL_BDTL_HW_PROTECTION - The parameter is incorrect."
When I try to format the Ext ROM with Repart_DOC, it says
"FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed."
Has anyone an idea what I could do?
Thank you,
Alex
You must go back to WM2003.
OK, thank you.
Related
Hi All,
I have an I-mate jasjar, This is the first time i tried installing applications to Storage Card (1GB), when ever i tried to install using Activesync 4.0, It doesnt ask me which folder to install i.e Like Default or Storage Card. And also If i click Add/Remove Programs in Activesync 4.0, I find that the checkbox "install program into the default installation folder" is checked and disabled. Hence I am unable to change it. Find the below image for the same.
Please can some one help me on this, on how to resolve the same.
Regards,
Francis.
Hi Francis,
1. Try inserting a bit smaller memory card (may be 512).
2. check if the momory card is not locked physically.
3. At the lowest, try to hard reset, but keep the memory card inside the i-mate while it install the windows. IMP: dont forget to backup important files before rebooting.
GoodLuck
Sidd
[email protected]
First of all get Active Sync 4.1 from here...
http://www.microsoft.com/windowsmobile/downloads/activesync41.mspx
On WM5 devices like Universal and Wizard I think you choose the location on the device, so you just install to 'default folder' from activesync and when it gets to the phone instead of then going ahead and installing it gives you the choice, phone or storage card.
On 2003SE Windows Mobile, you did have to choose the location on your pc in active sync and when it went to your device it went where you sent it.
Hi,
Mine is a MMC Card, so i dont think it can be locked Physically, also i dont have a smaller card to check whether it works. May be i can try your last option, but i have lot of sms, which will be lost.
Regards,
Francis.
Thanks a lot
As mentioned, whenever I tried to install the application in the PPC it ask me where to install. Thanks a lot !!!
Regards,
Francis.
Did you find out how to load a program to an SD card in the Universal? I want to know too, please.
Whenever I install an application I see a message saying: "This is from a unknown developer, do you still want to install? Press YES or NO." This is the only message I see, no option to install it to the SD card.
Any suggestions please?
Can anyone confirm if cabinstl does anything on WM5?
Its dialog pops up, but then I get the normal WM5 dialog then asking for a destination a second time.
I think I may have confused cabinstl by adding the following registry keys:
Code:
[HKEY_LOCAL_MACHINE\SOFTWARE\Apps\Microsoft Application Installer]
"fAskOptions"=dword:00000001
"fAskDest"=dword:00000001
which will force the Wm5 installer to ask for a destination. This may be useful to those who aren't getting this dialog by default.
However, I want my MTV. And cabinstl. Working. Properly.
V
i've do the reg hack, softreset but nothing succeded! any idea?
Hi,
I have a problem with an installed ROM but I can't use activesync to update the ROM image.
I have tried using the OSImage tool to transfer the rom to the SD card in the XDA but nothing appears to be there when I reboot. I get the Wallaby boot screen and GSM OK, but no option to lead the image. What can I do.
When I try to read the card after copying the image there appears to be nothing on it.
Thanks in advance,
Dale.
if you did it right
the sd card reader should not even be able to read the card
at all
When you are in the Bootloader. Which version is shown in there?
You can try making a backup of the current ROM on the SD Card and retry entering bootloader. Than there should be the screen if you want to download the new ROM on the card. This will show if flashing in generally will work....
Stefan
LumpiStefan said:
When you are in the Bootloader. Which version is shown in there?
You can try making a backup of the current ROM on the SD Card and retry entering bootloader. Than there should be the screen if you want to download the new ROM on the card. This will show if flashing in generally will work....
Stefan
Click to expand...
Click to collapse
Version is 5.17.
From the Wallaby bootloader I am unable to save the ROM to the card. It keeps giving me the error "CARD Key Invalid"
Where do I go from here?
Dale.
You have to change your Bootloader....
Take a look here:
http://forum.xda-developers.com/viewtopic.php?t=29476&highlight=bootloader+5+17+patch
Stefan
LumpiStefan said:
You have to change your Bootloader....
Take a look here:
http://forum.xda-developers.com/viewtopic.php?t=29476&highlight=bootloader+5+17+patch
Stefan
Click to expand...
Click to collapse
Thanks for that.
Unfortunately I get the following error when i try to downgrade the bootloader.
C:\XDATools>pnewbootloader bootloader_v5_15.nb0
ERROR: Unable to open target/WinCE file - Returned by WSARecv or WSARecvFr
indicate the remote party has initiated a graceful shutdown sequence.
ERROR: ITReadProcessMemory - Returned by WSARecv or WSARecvFrom to indicat
remote party has initiated a graceful shutdown sequence.
Unable to find flash info offset, cannot disable bootloader writeprotect
I get a simmilar error when i try to upgrade or downgrade the ROM via activesync Program A.
What can I do about this?
Dale.
After a bit of fiddling I no longer get the first part of the error, but still get the following:
"Unable to find flash info offset, cannot disable bootloader writeprotect"
So, what can I do to overcome this problem?
Dale.
Hi,
I have this problem, whenever I try to install any softwares into my jasjar, the jas jar responds, it will ask me if I want to install it on my device or storage card. then I already tried to click on either my device or storage card, but the same message always appear "name of the software cannot be intalled. to try install again to a different location, choose a location:
Device
Storage Card
then, I choose either one again, but this message appear again and again.
I do not understand what happen, because before there is no problem at all.
Can anybody please give me suggestions. Thanks. I appreciate your helps
Have you installed the program once before? Then uninstalled it? Is it an upgrade?
Or is this a completely fresh install ?
Hello.
I have a problem with the installation of software on my x1.
No matter how I try CAB is always only the message "installation of xxxxx.cab failed"
However, space is enough available.
I have tried to download cab from the web, moved it via USB-cable or downloaded an email-attachment. Fails everytime, same for storage-card or memory.
This issue appears since 2 days, don`t know what has changed
I run the latest official ROM and Radio for WM6.1
thanks
Raggi
it is a bug
on third-fourth try cabs can be installed
I have tried it now 15 times and couldnt install the .cabs
one thing is interesting: If want to copy/paste the cab to a different folder, this error pops up: "Cannot copy, access denied. Please make sure that destination is not write-protected, file is not used and that there is enough memory" (my translation into English)
If I create a new folder and want to rename it later, I get the same error
try to format sd card
issue is solved by doing a hard reset
If you'd given of chance I could have saved you the time of reseting. See this post I just submitted for someone else.
http://forum.xda-developers.com/showthread.php?p=3674266
thanks esudl, i've had this problem a few times; ill save that to favourites
Today I tried the SD install of ICS as described here: http://forum.xda-developers.com/showthread.php?t=1437463 Used brand new 16GB card, created \\ICS folder, copied contents of the 7Z file; In WinMo File Manager, opened CLRCAD, then HARET - after a green HTC logo, restart to WinMo, tried several times to no avail. OK, just a testing, can try later...
Then I changed the SD card, inserted my original card used with WinMo and restarted WM.
BIG PROBLEM - I'm getting error message whenever running a program now, error msg reads "The file 'some file' cannot be opened. Either it is not signed with a trusted certificate, or one of its components cannot be found. If the problem persists, try reinstalling or restoring this file."
Searched the forum, found this http://forum.xda-developers.com/showthread.php?t=392087. I have no reg editor installed, tried to install Total Commander but received "Installation ...was unsuccessfull".
What is the reason for this problem? How can I sort it out?
Thanks in advance
Have you an ActiveSync on your desktop PC? Try to use some registry editor that working via ActiveSync. For example "Remote Registry Editor", or look at that post. There is a link to such program.
Dr. Neuhaus said:
Have you an ActiveSync on your desktop PC? Try to use some registry editor that working via ActiveSync. For example "Remote Registry Editor", or look at that post. There is a link to such program.
Click to expand...
Click to collapse
Thanks. Downloadad/installed the CAregeditor on PC, opened registry of my HD2. I cannot change the value, getting "Write error-access denied/Cannot write value data". Any ideas?
Just 2 ideas:
1. "Connect to Device in CeRegEditor -> Tools -> Unlock Registry" (from this post). Or...
2. Hard-Reset
PS:
Some time ago I've used Android from SD, and got exactly the same thing... This caused me to reflash the ROM, but I've changed "0000101a" to "1" right after reflasing (this helped me to forget this problem).
Tried to unlock,still can't change the value. Also tried the other program recommended in the post but no - I cannot install it on HD2 - still the same problem :-(
Hard reset & ROM reflash probably the only way now, what a waste of time with reinstall/config of all the software/tools...
Anyway, thanks for your effort.