Hey all, i just recently bought this lovely phone from a friend of mine. I've been messing around with it for the past several days (Upgrading to WM6 and installing APPS, and even messing with the internet(tzone)). Anyways when if first got it everything seemed to be running fine and when i plugged it into the usb port for activesync, it worked. However the past day i tried to recharge my phone through the charger and later the car charger and it would not stay "connected." Like the little charge icon would come on and off. Me being the dumb person i am, tried to bend the plastic piece in the middle of the usb seeing if that would help make the connection better. While doing so i broke the plastic part and now it won't charge/snyc at all any more. Anyways, i figured i try to open up the phone see if i could maybe glue the piece back on. After opening it up though i see that i could maybe replace the whole conector ( with a lil soldering). i was thinking maybe buying some cheap electronic that had the same connector and replacing my wizard's connector with it. What are your thoughts on this? Could it work? I'm not an expert when it comes to soldering, but i do have some experience.
Related
Hi, my port broke. I managed to resolder it but now when I plug the phone to my pc, windows displays the usb not recognized alert... How can I fix it.
It sounds like you did not resolder it correctly.
Check with a magnifying glass to make sure you didn't accidentally bridge the connections with solder.
its quite hard to sold it right i have done it once it tookt me all day to get it right i tested it with the charger it it charges it should be ok at least my one was/is the first day the active sync didn´t connect at all but 2 days later i plugd it in and it connected so be carefull with the solder if u dmg the board you may say goodbye to your phone take time to do it right
afghanistan said:
its quite hard to sold it right i have done it once it tookt me all day to get it right i tested it with the charger it it charges it should be ok at least my one was/is the first day the active sync didn´t connect at all but 2 days later i plugd it in and it connected so be carefull with the solder if u dmg the board you may say goodbye to your phone take time to do it right
Click to expand...
Click to collapse
i think i have that problem... i soldered the usb port for a 8125(wizard100) and it charges fine as i can see the light. it charged for a couple of hours then the orange light turned green. so that's good. but i can't seem to get any response. i tested the battery in another phone to see if it actually charged (i was kicking myself before thinking i messed it up). so i dont think the board is dmged.... however does anyone know which pin corresponds with power, etc. so i can test for a response?
less worried, more concerned....
Ok, so i tested the unit without the battery and it comes on. However i can't seen to get it to work with the battery in it. Oh yeah one more thing the unit keeps cutting off.
Hi, there are lots of posts about damaged USB ports. I was wondering does anyone saw or uses any cap for USB. It should be something like rubber SD cap. Just plug it into USB and you can reset the phone in complete darkness . And it could be attached to leash loop with little thread not to lose it while on charge/sync. That would also prevent dust from accumulating inside USB port. Anyway I couldn't find anything like that. Maybe some DIY ...
I was thinking the same thing cause i am having to replace my tilt due to breaking the usb port with the stylus. I would love any ideas on how to do a cover.
bump..
sounds like something that should of came with the phone..
This would be a great idea since I have to realign my usb port every once in a while. The only way I can sync with my computer is by using the HTC USB Headphones adapter that came with my 8525. AT$T said that they would not exchange my Tilt for a new one because bent pins are not covered under their warranty due to "personal damange". It's really weird that I can't use my Seidio Cradle to sync with my computer anymore since it has the same proprietary USB jack. It will only charge the unit and if I move the Tilt while plugged in to the cradle, the connection is not always consistant.
healingtouch84 said:
I was thinking the same thing cause i am having to replace my tilt due to breaking the usb port with the stylus. I would love any ideas on how to do a cover.
Click to expand...
Click to collapse
Haha. I thought I was the only one. Went to do a soft reset, wasn't looking, and stabbed the USB by mistake. Didn't notice it wouldn't charge until the next day. Fortunately, I was able to bend the pin (GENTLY) back into place and it works again. BIG sigh of relief
I've search the forum first before I posted this message, but no post that gives me the slightest answer to this problem
I lend out my tmo Wing to my gf because her phone broke and I had G1 for awhile already. Apparently it's too much to handle for her so I bought her a cheap nokia prepaid in order to get my wing back.
I'm trying to back up her pics and ringtones from the phone, but I noticed it won't charge. The amber light won't turn. I double check again and I noticed the miniUSB port is super loose. I tried wiggling it, putting the cable halfway, taking out the battery, etc. Nothing work.
What should I do? Does anyone have experience this problem before?
Check the contacts on the female usb port. If they are corroded, which could be the case if not properly cared for, try searching Google for a way to clean them.
The contacts could be skewed at an angle, like my old Kaiser. I used a pair of tweezers to manually move the contacts back to their original position.
Try switching to another USB cable. My phones will only charge with a cable that has a very heavy-duty end on it. Normal USB cables won't cut it, I had to use one that came with a removable hard drive.
That's all I have for now. Hope it helps!
My port is screwed too. I got this charger off of ebay and love it.
cgi.ebay.com/Battery-Charger-for-T-Mobile-MDA-Vario-III-HTC-TyTN-II_W0QQitemZ350298289224QQcmdZViewItemQQptZBatteries_Chargers?hash=item518f67b448
I have two batteries, so one is always charged. I like it so much more than a traditional charger. HTH
hey guys, need some help here
so my phone is not charging, i tried the USB to PC, does not work neither does the wall charger, I do not get a orange led notification either. The phone would boot up for a second then turn off.
any suggestions?
I have this issue with my aftermarket battery from china, the battery is so dead that the phone doesnt even really know its there. It just happend to me yesterday. ill put up a fix tomorrow because i have my kid this weekend.
slickerxcuh said:
hey guys, need some help here
so my phone is not charging, i tried the USB to PC, does not work neither does the wall charger, I do not get a orange led notification either. The phone would boot up for a second then turn off.
any suggestions?
Click to expand...
Click to collapse
lucky for you, its the ebay battery for me its my oem battery. going to try to swap out another oem battery/charger and see if its my battery.
had the same issue, i noticed on mine that the battery pins on the phone tend to bend easily to prevent a good connection from the battery. phone would power on but wouldn't charge either.
is it the pins? i need some pictures or a video tutorial on this fix lol i have no idea what everyone is talking about, the pins look fine to me. im pretty sure that its my cable now since it didnt charge a blackberry phone either...
Damn how can this phone be so hi tech but made with th most CHEAPEST materials!
i bought a new micro usb cable, and its charging now...
slickerxcuh said:
i bought a new micro usb cable, and its charging now...
Click to expand...
Click to collapse
I bought one off of amazon and it would totally freak my phone out....no joke...it was just a wall charger no usb...now I only use the usb like the one that came with the phone and that is i.t
When you get a new phone, you should always condition the battery by letting it run completely down a few times in the beginning. When I was doing this with my phone when I first got it, after a complete drain it wouldn't charge. All i had to do was pull the battery and put it back in. Then it started charging fine. Not sure if this helps...
Also I wouldn't say these phone use cheap materials because people are not careful and bend the pins. I've removed my battery several times and the pins are perfect... If the pins aren't flexible, you wouldn't be able to get the battery in. In order to be flexible, they have to be soft. Pay attention when you are removing and replacing your battery.
You ended up figuring it out but I figured it would be good to point out that sometimes the connections on the battery/phone get dirty or pretty much any battery where it connects to the electronic.
What I usually do first when I have problems with any of my electronics turning on/charging is I take a cotton swab and dip it in rubbing alcohol. Shake it off cuz there will be alot of alcohol on there just so its not dripping and rub the connections then flip the cotton swap around then rub them again with the dry side. This doesnt work all the time but works enough for me to mention it. Static electricity will attract dirt and grime. Used to happen semi often on my touch pro since I used to have it in my pocket when I worked on a golf course.
Anyways just my 2 cents.
need help please people.
my phone hasnt been charging properly for a few days now, to get it charging now i have to get one of my missis hair bands and wrap it round my phone and then round the usb cable so it stays in , although today it doesnt want to charge at all now .
ive noticed that the connection in the phone is loose and you can move it round a litle bit,
now the bit i need help with , is do i take the phone apart and try to fix it.?. im thinking of doing this but unsure about taking phone apart ( dont think my phone is under warrenty anymore,) and im guessing the usb connection on the phone is fixed onto a board.
is it worth me trying that or should i just take it to a repair shop ?
take a dry toothbrush, give the usb port a good scrub. dirt often builds up in the bottom of the port and stops the usb plug pushing deep enough to get a good contact.
Have a good inspect of the usb port, bright light and magnifier is good, see if you can see buildup, or a bent connector, or somesuch.
Also look at the usb plug on the cable, its uncommon but not unknown for the metal outer enclosure to open slightly, and make for a weak contact.
Sometimes a cable simply doesn't fit well for no obvious reason, , i have a generic cheap ebay cable that will only work when angled up or down, like yours, but looks perfectly fine, and feels to fit the socket, while the HTC cable works perfectly, so i know its not the port.
If it all looks good, then chances are you have a dodgy connection from the usb port to the mainboard, which will get worse every time you wiggle and bend the cable to get it to work. In this case, you COULD try a repair, but there have been reports on here of some repair shops pronouncing it too fiddly to replace teh usb port, and a new mainboard would be the only other option.
edit - just reread your post and seen that you can wiggle the port. Broken solder, gotta be. Its not an easy solder, so if your a dab hand, then go for it, if not, see above.
Hi iainbp, heresandyboy had this same trouble in http://forum.xda-developers.com/showthread.php?t=903977 from post 16.
It looks tricky!
Just a thought though, I recently bought a cheap phone charger with multiple interchangeable heads for different phones. The microUSB one became difficult to charge with and it took me a while to realise that the metal bit at the end had detached from its plastic casing, and when I plugged it into the phone it just got pushed back into the casing. (got my money back)
Possible with yours?