Related
Hi,
As my wizard dropped in the water it got completely soaked.
I disassembled it to let it dry, see photos attached, put it together again and presto, almost everything works!!!
Just four keys of the keyboard do not work anymore, and as it all happened a week ago now I do not think this will be fixed.
Does anyone know if they do not work because of the water or because of the impact (the Wizard smashed on the street first)?
Has anybody ever fixed a faulty keypad?
Can anybody tell me where I can get a replacement keypad?
Let me know if you need instructions how to disassemble your wizard.
many thanks!
manhattan.
I have no answer to your question, but it is nice to see the inside of the wizard one time.
A couple of other people were asking about disassembly in other posts - so the instructions would probably be handy.
Hi,
I would love some complete instructions on dissasembly as I am about to take mine apart for painting and a hardware mod.
As far as the keyboard goes, you would be surpised how long they retain water, i doubt its a hardware problem, keyboard are pretty much solid state with only a tiny membrane for contacts. However it is this membrane that is most likely to be your problem, the contacts are very close together and covered in a film that can be verry attractive to water as it has rubber over it. So in essence I am saying I bet it is still wet in there, just a few droplets of condensation would do it.
Options, take it a apart and check and leave in a very warm dry place for a day, or II place whole wizard on a warm heater (not hot) for a while and see if that gets it.
T
Hi,
I also want to know the details of disassembly the wizard.
I think you had better post the instructions o disassembly here as I'm sure there are quite a few people who wuld like to know, me included.
Just a thought by looking at the picture (brave btw!)
Would it be possible to replace the 2,5mm headphone jack by an 3,5mm one and drill out a new hole for the larger connector?
Would be neat if you weren't so dependable on those stupid converters. Not a pretty sight anyway.
Thanks for sharing the photos.
I took mine apart some time ago to fix the stylist problem and when I put it back together some of the keys wouldnt work. The back light wouldnt work either. I found the problem was the little snap that secures the flat cable form the keyboard to the main board. There is a really small clasp that clicks down on the flat cable after you insert it into the connector. Once I took it back apart and snapped it, everything was normal again.
I plan on taking mine apart to change the keyboard form the English/arabic to just English, (anyone know where I can buy the keyboard/keys?) so any instructions you have will be appreciated.
Thanks
The stylii in the picture look like BA stylii.
Do I get 10 points?
will post instructions
OK guys I will put together the instructions and upload them here. I just have absolutely no time now so I hope you can wait a day or two....
Thanks for the comments. I am aware of the little lock that secures the mini flatcable that connects the keypad to the motherboard. I assume that is not the problem as I snapped it securely back in place.
I will try the heater suggestion, I suppose you mean to put the wizard in an oven set at let's say 50 degrees celsius?
The styluses in the photo are from my Qtek 2020. As the Wizard smashed I lost its stylus.... :-(
Sorry the photos do not show the display half of the wizard disassembled... I realised too late that others would benefit from pictures...
Cheers
Manhattan
I dont think I would put it in an oven. I would think that just inside a vehicle sitting in direct sunlight for a few hours would probably do, unless you are in a really cold climate. You may also try some electrical contact cleaner then get some additional heat to it after it evaportates. There is probably something that has trapped some moisture somewhere. Just for info, I dropped my Jamin the other night about 4 feet directly onto a tile floor. It bounced a couple times, ejected the SD card, and reset. But it is working fine. However, I had a bud that dropped his 2 day old Sony Ericsson P900 into water and dried it off immediatly and let it air dry. It worked, but he had problems ever since. It would drop calls and restart all the time. So there may not be a complete fix for it.
Good luck
Hey guys, someone posted the HTC Service manual for the Wizard!
In this manual you see pictures how to disassemble the phone!
It's realy the best manual to use for opening your mobile friend....
Good Luck
http://forum.xda-developers.com/viewtopic.php?t=43836
I've successfully fixed my girlfriends crappy creative keyboard once after water damage using a pencil. Depending how the keyboard is made, most of the time there will be really thin conductive tracks literally printed on the substrate. The water isn't particularly nice to these tracks and I found that in some parts there was noticale oxidation/corrosion. By very lightly scratching of the affeted paint and then going over it with a graphite pencil this did the trick.
Just an idea, personally I probably wouldn't do it to my vario but then again I'm still in the honeymoon phase with it.
Good luck
I fix phones for a living for many stores and have many phones that have water damage
what you dont do is charge it.. it will burn out the board
what you do is let it dry out, use the service manual and let it dry out in parts
then get white spirit and a toothbrush... dip it in and clean the contacts for yourk eys
once done, again let it try and then see how it goes. thats what i do, although we have a machine that sends out sonic pulses but the above method works too especially when im lazy
HTC Wizard Disassembly
hi guys. a lot of confusion over this simple matter. I don't know where the PDF file everyone's talking about is, most links didnt work, but here's some pics. USE AT YOUR OWN RISK! hahahahaha!
http://www.pdagold.com/articles/detail.asp?a=274
Hi,
I have a O2 xda model
IPL 1.01
SPL 2.21
GSM 01.12.10
OS 1.5.4.2
there is problem in formating the phone.
Even after a hard reset the Os wont boot,
it says that "formating is failed".
there is a prolem in the flash memory of the phone.
please help me with the assembly and disassembly process so that i can fix it.
Any one?
Hey Guys,
Well, I'm a bit gutted really! I dropped my XDA Mini S on the floor with the charger in and the connector IN the phone has come apart from inside the phone. The little metal bit is practically hanging out. I'm wondering, if i were to take the phone apart could i re-connect the little part? (I have a soldering iron if thats as simple as its going to be?)
Just wondering if anyone had any guides on how to take the phone apart and take a look at whats wrong?
Any help would be so much appreciated!
Many Thanks,
Tom
The service manual is hosted on the ftp site.
ftp://ftp.xda-developers.com/Wizard/Docs_Tutorials/
Hope this helps.
I suspect you probably broke the socket off, but if you have a soldering iron, you might as well try to get a new mini USB connector to work with.
You might try Pocket PC Techs:
http://www.pocketpctechs.com/main~unit~UTStarcom_XV6700-554~area~repairs~item~REP-USBCON01~name~UTStarcom+XV6700+Mini+USB+Connector+Replacement+Service.htm
I rang them up about an issue I had (screen on the fritz) and they seemed pretty knowledgeable and helpful.
Alternatively there's a company I found today in the UK. I can't vouch if they're good or not.
http://www.xdarepairs.co.uk/home.asp
Good luck.
Well I also have an issue with my wizzard... the mini jack connector (of the handsfree) is a bit loose.
What I am saying is that it does have a good connection with the rest of the circuit and sometimes the sound of the speaker goes off, then I have to insert the habdsfree and tickle it a little bit until it has a good contact.
? have some basic soldering experience,do you think I should give it a try?
Given my device has been apart too many times for me to admit to I thought I'd crack it open to take a pic for you guys. Not sure if this pic will help for those wanting to do some soldering:
Very large pic: http://farm1.static.flickr.com/216/452691530_f47801708f_o.jpg
Excuse the dust.
Ah! That picture at the bottom is exactly what I needed. The metal but at the bottom (the big sqaure) has totally sheared off....bloody thing. Thanks so much for the info on the repair guides. I may give those repair guys a call if i can't get it to work myself.
Thanks alot you guys
As for you WizeMan, it all depends on if you wish to void your warrenty or not. At the end of the day, I installed WM6 on my device so O2 would give me the finger if i tryed to claim. If I'm honest, I'm getting an upgrade next month so I'm not to bothered if I balls it up! Would be nice if I got it working though....
Lemmie know how you get on
unlock k-jam
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........
lironasseo said:
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........
Click to expand...
Click to collapse
A little bit of a thread hijack but that means it is SIM unlocked.
Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm
WizeMan said:
Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm
Click to expand...
Click to collapse
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.
AsGF2MX said:
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.
Click to expand...
Click to collapse
Allright here is the deal.
1. I found out the break in the soldier joints when i opened it. I was really suspicious about it because when i inserted my headphone jack into the connector, i had problem with the contact; the connector was loose and it muted my phones speaker. When i disassembled the phone using the service manual i saw with my eyes that the the joins where f-ed up.
2. I dont really need the signal hack i just wanted to experiment, i have 2.25.11 cingular radio rom and its great.
Btw i suppose you should better use the sponge, because the rubber may wear off but not the sponge...
Thanks for the tip on the sponge. I am going to grab a used but allegedly "like new" body from eBay and also get one of those covers as well.
Hi all,
My wife spilled a glass of beer on my PDA, and now the top front buttons don't react like before. Sometimes you don't hear the 'click' and you can feel like they got stuck.
The keyboard looks fine, so the problem is only the with the top buttons at the front of the PDA.
Have anybody tried to take apart this PDA? Would be easy to open it and clean everything before putting everything back?
Thanks a lot
I completely soaked my Ozone about a week after I got it... knocked it in the sink. I like to think that I was among the first to void my warranty, Lo..l?
The phone is really well constructed for what you need to do. All of the critical electronics are very well shielded on the board, nothing difficult about separating the board from the case.
Six 'star drive' screws on the case (that's where the warranty sticker is), one tiny phillips on the board - board pulls up off of pins, away from the usb connector and Bob's your uncle. The keypad is not fastened to the case, pull it right out.
Watch the ribbon cable for the lcd - I would not recommend disconnecting it. there should be enough play to allow you to work. Make sure you're working in a really clean environment, and check the inside of the plastic lcd cover obsessively right before reassembly. If you're anything like me that one little catpet fiber or cat hair or whatever the hell will drive you to take the phone apart again 4 days later...
Sorry about the ramble... it's late. Short answer is: Nothing to it.
Good luck!
Thanks a lot for your post. It was really helpful.
I will probably try it this weekend.
I'll post here the results
Cheers
So if I wanted to buy a different color keypad (dont like the green) it shouldnt be hard to take apart??...I change screens in Env/Voyagers a bit so have a little knowledge...
Hey guys,
The earpiece speaker on my G1 has developed a fault, the fault being it doesn't appear to work, how easy is it to source a replacement for it and how easy is the repair itself? is there any guides as to how to do it around? (i looked but i couldn't find anything).
I've tried flashing the rom and doing a hard reset but its still faulty.
The loud speakers working fine though so atm all my calls have to be done on the handsfree kit or via loudspeaker which can get annoying.
any help is much appreciated
regards
Streather
Are you using a ROM where sound works?
What ROM are you using?
Tried it with cynagen and the stock tmob one, same results.
Same problem
I'm using CyanogenMod 4.2.5. I dropped the phone about a foot (it fell out of my shirt pocket as I was tying my shoe!), and the earpiece stopped working. Everything else (speaker phone, etc.) works fine.
I've seen a number of similar cases in other forums, so I'm thinking that this is a weak point. I'll attempt disassembly and see if the speaker contacts got moved or something simple. Fortunately, replacement receivers/earpiece/speakers are available over the net.
Meanwhile, I'd love to learn of others' experience with this. The tech manual makes it look like you have to just about completely disassemble the phone to get at the earpiece, even though you can easily access 3 screws on the back of the lcd. Is there a shorter route to the receiver than a complete disassembly?
[update] I found some good info (including a technical manual) by Googling "g1 phone disassembly". And searching for "g1 speaker" on eBay gave some decent looking results.
[update 2] I disassembled my phone, took out the receiver, cleaned its contacts, replaced it, and and reassembled everything. That was a pretty serious chore, and it demonstrated that a nearly complete disassembly is required to access the receiver (yes, including all the stuff at the opposite end of the phone). I don't know how to test the receiver without being in cell range, which my house is not. But at least nearly everything else still works, except the camera--I need to tear back into the phone and make sure I fully seated the FPC. I think finding a replacement receiver will be a challenge--most of what turned up on eBay is actually the main speaker on the back of the phone, and I have yet to find a vendor that sells receivers.
Sadly, you will almost have to tear down the whole unit to get to it. It's not extremly diffucult, but you will need to be steady and gentle. Good luck.
Success!
I haven't seen many report back after tearing apart their phones to address issues with a bad receiver, so here goes. My simple-minded approach of opening it up, cleaning the receiver contacts with a pencil eraser, and ensuring good alignment before reassembling WORKED. I did not have to buy a new receiver.
Now if I can just get my camera to work again (I think I didn't get the cable well seated).
[update]: camera works! Seating that FPC took some nimble fingers--I got it on the 3rd attempt. I hope this proves useful to others who, like me, do not have the warranty option for various reasons.
I dropped my phone once, by accident, same thing happened. The speaker you use to put your ear up to when making a phone call doesn't work, but the speaker phone speaker works as does a bluetooth headset. Called HTC lied said that it just stopped working out of no where, they said its covered under warranty. Luckily the phone is under warranty until March and will be replaced.
I ran into the same problem. I was having intermittent problems with the earpiece. Yesterday I was able to take out the battery and put it in and it started working again. Today that didn't help either. I saw this thread and I thought that I'd try blowing really hard on the earpiece to see if that helps. It seems to be working again! I hope it continues to work.
dirtprof said:
Now if I can just get my camera to work again (I think I didn't get the cable well seated).
[update]: camera works! Seating that FPC took some nimble fingers--I got it on the 3rd attempt. I hope this proves useful to others who, like me, do not have the warranty option for various reasons.
Click to expand...
Click to collapse
Can you post details on how to do this?
My camera stopped working too.
I personally found it easier when disassembling the phone to carefully lift the entire camera and IMEI sticker as a whole unit and remove it as part of the motherboard. That way you dont need to mess with that hard to reach connector. So from where you are at, lift the board back out, reattach the camera assembly, and reassemble as a unit. I think you will find it is MUCH easier
Seat the camera FPC fully
RueTheDay said:
Can you post details on how to do this?
My camera stopped working too.
Click to expand...
Click to collapse
I had to lift the motherboard up and away from the hook that held it down in order for the FPC clip to open fully. Then I inserted the FPC *fully* before closing the FPC clip (my failures resulted from not being able to fully seat the FPC because the FPC clip could not fully open as long as the motherboard was in place). Then the trick was to get the motherboard back under its hook without accidentally pulling the FPC back out again. What I did was to press it gently straight down, using my fingernail to ease it past the hook.
Good luck!
bump...
Yeah looks like all there is on Ebay for speakers is the back one, the one for the receiver earpiece looks like it has two wire connections at each end while the one for the back speaker has them right next to eachother.
So if anybody had this problem, it is very odd and might have to do with the spring connection maybe.
Still I had this problem before and it fixed itself randomly, but this problem came out of nowhere because 12 hours earlier I had dropped my phone on its back and it continued to work fine. Than on my way driving randomly it would not work and I barely set it down in my car.
Once again hopefully somebody has found a part for this because ebay only has back speaker parts.
Best bet is to blow on it and massage it or tap it until it works, damn this sucks because it is basically the very last step to get to after dissambling your phone. So much work to get to such a common problem for many people.
I almost wanted to try to shortcut it and undo the two screws on the screen section to move it around to make connection. Now I am the deusche bag with the bluetooth in his ear all the time.
I almost wanted to try to shortcut it and undo the two screws on the screen section to move it around to make connection.
Click to expand...
Click to collapse
That was what I tried at first. It didn't gain me access to the speaker.
Taking the phone apart is a pain. You really need nimble fingers and faith that you're not breaking the phone when you're levering apart the *very* tightly held together plastic parts. HTC did not make this thing with servicing it in mind. Just be sure to have the right tools (including light and a good magnifying glass if you're over 40) and patience.
Removing the 3 screws that are accessible without disassembling the entire phone will get you in there if you are VERY careful. Unfortunately the one I tried this on did not work differently with a known-good speaker in it. You can delicately dig out the old speaker with a knife (Xacto) and drop the new one in. Takes patients, but not nearly as hard as disassembling the entire phone (been there, done that x10)
I have at least one spare speaker. Maybe more, gotta check my stockpile!
Hey,
My phone got dropped in a rum & coke on Saturday, so i soaked it in 90% rubbing alcohol and let it dry in a rice bath. after 4 days in the rice, it looked dry, so i turned it on. IT WORKS! The screen looks a little trippy (the pattern is even changing throughout the day) but the touch and accelerometer work great. The only real problem is the speakers sound like crap. the receiver is so quiet that it sound like they're wispering, and the back speaker is all crackely.
I found a replacement receiver speaker, but as i haven't taken it apart yet, i was hoping one of you could tell me if this looks correct.
http://www.tvc-mall.com/details/Replacement-Speaker-Earpiece-Receiver-for-HTC-G1-HTCO-G1/photos.htm
If so, i guess i'll order both speakers and attempt to replace them.
That looks about right. Bear in mind, of course, that those pictures are greatly magnified. If you haven't taken apart a G1 yet, you're in for a bit of nerve-wracking prying. Just go slowly and be patient. Getting all the way to the receiver speaker means taking the phone most of the way apart.
Thanks!
I have taken apart a phone before, the Dash (excalibur). I had to replace the screen, it involved removing almost every component.
I think i'll go ahead and order it, and cross my fingers. right now the phone isn't much more then a tiny computer, since i can't hear anyone and i don't have a Bluetooth.
Hi there,
I broke my touch screen and tried to replace it by myself.
To make a long story short, I failed miserably (I broke the screen under).
However, I learned a few things I didn't met in the forum.
A- Disassembly of the case.
1- The Legend is glued. So, you have first to use hoven to melt the glue before being able to do anything useful.
15min/ 60 degree in the oven. Or use an hair dryer (I used the former).
2- Don't forget to remove ALL the screws (even the one behind the IMEI notice).
3- Don't try to open the camera lid before loosening the glue or you'll damage the aluminium body.
4- You have to unplug all the différent cables, so take notes to remember where all of them goes.
5- You must disassemble all the boards. There are 2 boards. One supporting the sim / SD connector, and one supporting the screen/touchscreen.
6- When disassembling the screen board, remove it by pulling the touchscreen at the bottom, and lift it up. don't pass a tool on the sides to remove it or worse, under the touchscreen, you'r tool will touch the screen under and break it (like I did). The screen is very, very fragile
Now, I'm stuck here because I can't remove the connector of the legent which is passed under the shield on the back of the screen.
I'm not able to remove the screen so I would like to know how to remove this shielding or get back the touchscreen connector to be able to replace it.
Once I figure out how to remove this shiled, I may be able to remove the screen too.
But now, I'm clueless (it was 2 in the morning when I gave up).
Maybe, some of you knew the trick to open this phone further.
I'd like to hear about it.
A little up to my post for the ones who did not read it till the end:
I can't remove the connector of the legend which is goind under the shield on the back of the screen.
I would like to know how to remove this shielding or get back the touchscreen connector to be able to replace it.
Once I figure out how to remove this shield, I may be able to remove the screen too.
But now, I'm clueless (it was 2 in the morning when I gave up).
mate it sounds like you have trashed your phone.they are built NOT to be taken apart.They require special tools and process to be repaired. The only thing i would suggest is contacting your insurance company and let them know that your phone was crushed under a car or something and then crush it under the car and you can get it replaced. If you dont have insurance, take some out and make a claim in say a month or two.
Its not an honest thing to do but your phone sounds busted and its the cheapest way of replacing that handset.
Post a pic of it if you can
Unfortunately, I have no rights to post a link or some put some pics.
Something about spam and profile that should be reviewed before being able show any pics.
This device is glued. No specialized tools are able to open it without removing it.
That would mean that the phone cannot be repaired, only replaced. My phone's motherboard was replaced, so at the service stations they should have special tools.
Fixed it!
Bottom right hand corner:
Bend the shielding back just enough to allow you to slip the connector in & then use a little glue to stick it back.
Maybe I was lucky, but my phones working as good as new again
I fixed my Legend
Guys, I know it's been a while since you talked but in case someone else is looking for this info, that's what happened to me:
I cracked the display of my legend and purchased a new one on eBay (roughly 40 pounds) - obviously delivered from Hong Kong but a genuine Samsung (in case you didn't know the Legen's screen as well as most of the AMOLED screens are Samsung's).
Then I used the above information plus some YouTube videos to give myself an idea as to what should I do. The result follows:
I used a hair dryer to heat up the back of the phone (camera and loudspeaker cover). Perhaps I should have been more patient as in the end I decided to use a knife with a very thin blade to lift it and I scratched the plastic and the aluminium body a bit. Anyways - the back clicks in but is glued in addition to that so you have to use both the heat and gently applied force.
Once you remove the back cover (which took me the longest out of everything) you should start removing screws. There's two behind the back cover and six behind the bottom cover (where the battery is). At this stage you don't have to remove all the screws - the bottom two, the one behind the IMEI and the one under the VOID sticker hold the main board but the two screws sitting deeper inside the phone's body hold the front buttons so you may leave them for now.
Now comes the trickiest part so read carefully: the main board is held inside the unibody by the screws (which we already removed), but is also glued right below the camera lens and along the sides. You should probably heat it up as much as you can and for a long time. I decided to do it the hard way. My dislplay was already cracked and it's the most delicate part of the phone so I said "whatever" and used the same knife as before - moved it alongside the screen (pushed it in gently from the front) until there was no resistance (the glue let go). Then I pushed and I heated the thing up and pushed and tried from every angle until finally the board slid out of the unibody. I hope you'll find it easier then I did as it seems that everyone describing it found it quite doable.
Now everything becomes easy-peasy. Remove the remaining screws to put the buttons aside (you'll have both the actul buttons and the tiny board with sensors - the latter sticks to the screen but once you remove the connectors, yu can take it off too). All the connectors are quite easy to remove if you hav a needle or something (just pull them out gently). I didn't worry about noting which is which as ther is practically no way you can mix them up - they're very different.
The rubbery plastic black surrounding of the board clicks in, so once you find the right spots you can lift them gently and take the thing off. You'll be left with the display covered by the shielding from the top and a thin metal board from the bottom. You have to remove two more screws to disconnect the main display plug.
And the final bit (that's where the thread's author had a problem I believe). My display was cracked but the shielding - fine. These two are glued together so I had to find some space for my finger nail and lift the shield. By slowly and gently pulling it apart I detached one from the other - and had to do the same thing with the metal board. Don't forget there's some extra stuff to remove from the back of the display - they're all glued but the glue will remain fresh enough for you to glue them again - this time to the new screen. The same applies to the front shield. I hope you won't let any dust sit on it in the meantime. You should have a screen protector on your new display if you bought it like I did. Remove it now and the display will be happy to stick to the old front shield just as if it was always there. The metal back will also fit in.
Now you can go through the above process backwards - just remember to connect all the connectors.
What I didn't do: I didn't use ANY glue putting the phone back together. As an effect the front shield is sticking out a bit (doesn't sit in the unibody tightly). It doesn't affect the phone itself but it gives you the funny feeling that something isn't 100% right. But I prefer that than screwing something up with a misuse of glue (glue can be disobedient).
The most important piece of information: the phone is working 100% correctly as if it was never disassembled by an amateur. Apart from two scatches on the back, the VOID sticker missing, the front sticking out slightly (less than a mm) and the missing battery slider (which I forgot to put back in and didn't bother to repeat the whole process for the sake of it) - there is nothing wrong with the phone. So if you ever crack you ever crack your Legend's screen - you can try fixing it yourself if you have the courage.
I would like to see some photos too But I'm never gonna take my phone apart - can't see the point
Foto's
Nice thread, i myself am wondering, if a better gsm antenna can be fixed inside the phone. and connect them to the 2 connections.
Do you have any pictures of the inside housing etc?