GPRS break prevention during calls and GSM-offline periods - Networking

It seems I found solution, at least for Qtek 9100 (latest official firmware).
Just use this CAB or add the key to the registry:
Code:
DWORD HKLM\Drivers\BuiltIn\RIL\EnableATANocarrierWorkaround = 1
Also works on Herald, but there is such key by default.

thanks for the tip.... I'll try it for my problems with modem disconnections I keep getting on my hermes when it switchs between 3G and 2.5G and using i.m. clients.
oh I will report back here tomorrow night

sorry to report it didnt stop my problem.... oh well

think thats an operator issue
recall in the early 3g days people even
had dc of normal phoning when changing
from 3 to 2½g

This fix deals with 2g GPRS and GSM absence (metro tunnel, for example).

Related

QTEK9100 and GPRS/EDGE - AAARGGHH!!!!

For some reason - my QTEK 9100 fails to maintain the connection to my GPRS service. Once I connect, it holds the connection until I make/receive a phone call. Thereafter, the device shows the connection in place, but it fails to pass any more data through the connection. To keep using the data connection, I must either soft reset or switch flight mode on/off.
(Needless to say, I have been able to use my SIM in other GPRS-enabled phones).
ROM 1.1.7.5
Date 9/22/05
Radio 01.01.10
Protocol 4.0.13.16
ExtRom 1.1.7.105
Anyone have any ideas?
Is there a ROM upgrade or RegEdit that could do the trick?
Same **** with mine 9100 on MTS. We should get together to solve this issue. Let me know if you got the solution. My ICQ 2662731, phone no. 916 137 7540, Leonid.
Absolutely the same problem with my Qtek 9100 on MTS. Some people on the forums say it's operator's problem; others claim it's not. However, switching from MTS is not an option for me anyway (corporate cell phone number, etc.) so I would be very much obliged for any solutions, or at least hints towards what can be causing it.
One possible solution (haven't tested myself yet) is setting GPRS to 'always on' via the registry editor; however
a) Will it drain my battery much more than usual?
b) Won't GPRS get disconnected in standby mode?
hi
hi. try to initiate GPRS connection with the default inbox email. press send and receive to check email. let it connect GPRS. when someone call u. it still maitain but the during call, the other person must pick up the phone. if nobody pick up the phone. the GPRS will have problem and need to turon and turnoff radio again. this is the only to maintain gprs, that is, to initiate GPRS connection with the default inbox email.
malice93 said:
One possible solution (haven't tested myself yet) is setting GPRS to 'always on' via the registry editor;
Click to expand...
Click to collapse
I tried to set it always on, it didn't help.
malice93 said:
Absolutely the same problem with my Qtek 9100 on MTS. Some people on the forums say it's operator's problem; others claim it's not. However, switching from MTS is not an option for me anyway (corporate cell phone number, etc.) so I would be very much obliged for any solutions, or at least hints towards what can be causing it.
One possible solution (haven't tested myself yet) is setting GPRS to 'always on' via the registry editor; however
a) Will it drain my battery much more than usual?
b) Won't GPRS get disconnected in standby mode?
Click to expand...
Click to collapse
ad a) -
One thing I know for sure:
it will not drain your battery any more that when connecting gprs on demand. I used to use the "grps always on" feature and can't tell the difference in battery life.
Regardless of the "gprs always on" setting I do sometimes have problems with the connection. The icons (gprs) say it's on but no data is transferred (no e-mail/www received) but it happens very rarely and I can't tell in what circumstances.
By the way: holding the red off-hook key for 5 secs closes the gprs connection - check if it doesn't make your problem easier to bare ;-)
Maybe you could try another operator's SIM - at leat you'd know if it's the Wizard or the operator.
Salute/k
kristo_ch said:
By the way: holding the red off-hook key for 5 secs closes the gprs connection - check if it doesn't make your problem easier to bare ;-)
Click to expand...
Click to collapse
Yes, I know about this one; however, since GPRS won't reconnect anyway, this doesn't solve anything for me.
Oh well, I'll keep experimenting and hopefully Qtek will release some ROM updates in the future to deal with the problem.
Update: After playing with the settings a bit, the problem indeed seems to be with phone calls; i.e. I can disconnect/reconnect GPRS manually without any problems, but once a phone call is made or received, GPRS stops reconnecting. I have a suspicion it's actually an operator issue but haven't had time to try some other SIM yet.
malice93 said:
Yes, I know about this one; however, since GPRS won't reconnect anyway, this doesn't solve anything for me.
Oh well, I'll keep experimenting and hopefully Qtek will release some ROM updates in the future to deal with the problem.
Click to expand...
Click to collapse
I called service today about this problem, they heard nothing about it, they said. Also they invited to flash rom, that was released month ago, they said. I asked them about version but call operator didn't know.
I'm afraid to do that because they could flash older verison than I have, and there are some roms that have troubles with incoming calls, I read in russian Qtek forum.
My version:
OS: 1.3.9.4 RUS
Date: 9/29/05
Radio: 01.01.10
Protocol: 4.0.13.16
ExtROM: 1.1.7.105
I read there are some utilities to save rom but I cannot find how to save rom to hard disk to restore it in future surely.
My version is:
ROM 1.1.7.9
Date 9/16/05
Radio 01.04.10
Protocol 4.0.13.17
ExtRom 1.1.7.111
(Russian OS)
Just read on some Russian forums that there were the same problems with s100 until the new radio version was released, so I guess we just have to wait.
vishny said:
malice93 said:
One possible solution (haven't tested myself yet) is setting GPRS to 'always on' via the registry editor;
Click to expand...
Click to collapse
I tried to set it always on, it didn't help.
Click to expand...
Click to collapse
Just tried it myself, didn't work for me either.
So far, the problem can be diagnosed as: regardless of GPRS status, a phone call (outbound or received) will screw up the existing GPRS connection and any future attempts to reconnect unless a soft reset/flight mode switch is made.
I hope to god a ROM update will be available in the near future; meanwhile, any and all suggestions are welcome.
Today I visited service, they flashed me the same rom I already had. Then they tried to solve problem at least 2 hours but with no success.
I advised them to be ready for crowd of users of 9100 who connect to MTS.
Technician said I have to wait new rom update, but he cannot say nothing about release date.
I want to beleave...
Some guy at Russian forums put forth an idea that our problem might in fact be an issue with lousy MTS implementation of EDGE.
So in theory it could be solved by turning EDGE off entirely (if it is indeed possible).
Same problem on my Qtek 9100 ... is there any updates available for the ROM?
I have this same problem on both my Kjam and Qtek 9100. I am in the United States and use Cingular. I suspect this is not a carrier problem.
I'm in the US on Cingular with a Qtek 9100. I think the issue is that the carrier drops the GPRS connection after time, or the signal is lost and WM5 doesn't react. Either way, seems like leaving GPRS in constant ON mode plays into the problem rather than help it. After installing GB-SOFT Tweak http://msmobiles.com/news.php/4714.html and setting it to release GPRS if unused for more than 10 or 15 minutes, I don't get the GPRS problem nearly as often. Furthermore, when a GPRS lockup does occur, turning flight mode on and then off again restores function without the long cycle time of a soft reset
Christian
I had the same problem on my IMate and it was fixed by turning off (2sec) and then turning on your device once the GPRS connection was established. Haven't tested on my jam yet
I have the same problem since upgrading to AKU2 ROM - before I never had that issue...

Vario II network coverage question

Recently my Vario II intermittenly loses network signals, it says No Network and I have to toggle phone off/on to make it search for signal again. This only happens when I'm at home (Charlton SE7 area).
Rom 1.21.110.3 (19/06/06)
Radio 1.05.05.00
Does anyone have the same problem?
toucam said:
Recently my Vario II intermittenly loses network signals, it says No Network and I have to toggle phone off/on to make it search for signal again. This only happens when I'm at home (Charlton SE7 area).
Rom 1.21.110.3 (19/06/06)
Radio 1.05.05.00
Does anyone have the same problem?
Click to expand...
Click to collapse
Flash HardSPL first, then upgrade your radio.
Ive linked to my guides incase your unfamiliar with the process.
The newer radio should possibly increase your GSM efficiency. Are you in a decent area for reception?
mrvanx said:
Flash HardSPL first, then upgrade your radio.
Ive linked to my guides incase your unfamiliar with the process.
The newer radio should possibly increase your GSM efficiency. Are you in a decent area for reception?
Click to expand...
Click to collapse
Hi, many thanks for your detailed guides. I've upgraded Radio to 1.38.00.10 but the problem still persists. I'm in a very good coverage area, always get full bars 3G when it works. Soft-reset my phone and now it's searching in vain for network signal, I'm confused
What operator are you with ? Maybe the cell where you live is getting overloaded. We had a problem similiar to this last month when our local base station had a problem. Our work-around was to disable 3G but not using a Hermes . Apparently the handset tries to register using the 'best' data-bearer its configured for. So disabling 3G made it register with GPRS which worked fine. They then fixed the base station and we were able to re-enable 3G. I would
guess Charlton would have a lot of subscribers per cell. You would expect the coverage to be better in a built-up areas but who knows. Maybe an enquiry/ complaint to the operator would at least tell you if they know of a problem and if its temporary or longer term
Cheers for that. I'm with T-Mobile. What's bugging me is that this signal disappearance only happens sometimes. It's not that I don't have 3G (or signal for that matter) at all, I still get full 3G signals fine most of the time. But you probably were right, looks like it's a fault from the operator's cell in the area, I will give them a call next week to see if there's an explanation.
I've noticed this problem when I'm in the south London area (very general I know). People have got around the issue temporarily by forcing the phone to GPRS only
More problems! After upgrading to 1.38 and trying all sort of "good" radios like 1.17, 1.27, 1.34 I can't make/receive calls unless GSM is forced. There must be something wrong within my immediate area because with the same radios everything works flawless just 10 mins down the road. I just called TMob and there's no technical fault or anything from their side. I will just have to put up without 3G until the problem fixes itself
There are lots of people complaining about 3g on T mobile in UK. They seem to have serious issues with Hermes devices and the dropdown to GSM.
I had a problem six months ago with my hermes on orange at home in SW London. For a few weeks it was mucking about - I rang O who advised me that they were experiencing some local issues but would fix them within days. I switched to GSM for a few days. When I switched back its worked fine for last five months.
3G gone mad!
the same thing was happening to me. Full 3G reception in Leicester, tried to connect to get my e-mails and then the signal totally goes. The same thing happens when I make calls as well. Switched to GSM and everything worked. Now in York and everything is working on 3G.
Network is T-Mobile.
This sounds similar to the issues I am having.
Do you get the phone hanging as it attempts to start a call and then after a while a message stating that it was unable to connect?....sometimes resulting in a soft reset to bring the device back online? In my case toggling bluetooth will reset the connection.
I am with T-Mobile in Glasgow but get the same issues during the day in Edinburgh
No 3G
aidanbree said:
This sounds similar to the issues I am having.
Do you get the phone hanging as it attempts to start a call and then after a while a message stating that it was unable to connect?....sometimes resulting in a soft reset to bring the device back online? In my case toggling bluetooth will reset the connection.
I am with T-Mobile in Glasgow but get the same issues during the day in Edinburgh
Click to expand...
Click to collapse
No mine doesn't say anything, it sounds "ding ding" after a few secs like when you press the hang up button. I can use the Internet but anything to do with calls is just impossible. I've switch to GSM now and everything's back to normal. A bit annoying can't use 3G at home.

Signal problem in PDA2K..

hey guys...this is my first post here...
my pda2k keeps on dropping signals and sometimes halt during a call...
at first.....as instructed..2 time restarting solved the problem..
can you guys plzz help me out.......im using wm6
thnx in advance
What version of Radio do you using ? Try to upgrade to the last version.
my BA info is as follows
ROM version 5.60.00 WWE
radio version 1.12.00
well from where can i get the latest version of radio??
wel..i found it..and i am upgrading radio...
less see what happens
.....upgraded to 1.15.00
....no success......
im not the first one to have this problem..it ws in 2003. 2005 and now in wm 2006 now....
dunno what to do.....dont wanna throw away my pda2k
Maybe it is an hardware problem?
If your problem is in WM2003, WM5 and WM6, just get the phone to a repair or a recycle center....
but the thing is ..it was working fine....
and after installing a resh rom...it works for like 2 days with no problem...
im sure that its not hardware issue....
its the same problem....which everyone esle is having in this forum..abt signal dropping...dun think tat this harware problem can come to lot ov ppl at the same time...
the problem is with the phone company...
my pda2k also gives me similar problems...
but when i'm travelling to some other countries and using a local sim card there... i do not see any such problem... even while roaming sometimes... i do not see any problem with the current sim card.
i think it is the home service provider which has the problem.
If you have signal dropping, replace the flex cable.
The flex cable signal dropping is a common problem to any slide phone.
In fact I slide the phone halfway to test the signal if it will drop or not.
No signal drop means good flex cable.
Same case with Nokias and other phones.
I've had my friend's BA flex cable replaced and signal drop is solved.
also, one old battery can do that issue.
with my older battery, it used to cut connections sometimes. with the new one, keep connection.
hmm...but the thing is...that this fone was working fine in my country i.e Pakistan..but its giving problem here in canada.......and it actually came from canada before....
i dont know what to do....there were also issues like that with my imate-Pocket pc before...and now same is with PDA2k...
i have chaged a lot of sims...but no success.......
I personally believe that there is a bug on the radio dll.
If you are using WM2003, try this workaround to see if it helps: http://forum.xda-developers.com/showthread.php?t=340557
In your case, activate only the 1.900Mhz band or the 850 / 1900 band only. I believe that the former is better, though.
I've been only using it for the last 2 days, but so far so good.
JP
Well same problem here in Bulgaria. We have 3 Telecoms. Unfortunately i have subscription to one of them and some times like every couple of months I have the same problem. Green light blinking, but when someone is calling me - out of service. It rings, but after i pick up - it drops the call and gives "No service" This last for about a day or so. When i switch sim cards to another service provider - it works fine. The same thing happens when I travel from one town to another. I thing this is due to poor software configuration in the GSM towers. Overall for three years this happens to me like 10-15 times for couple of hours to one day. And I have this problem only with one provider only. No work around as far as i know.. Sorry
signal problem partially solved.
JPBRA said:
I personally believe that there is a bug on the radio dll.
If you are using WM2003, try this workaround to see if it helps: http://forum.xda-developers.com/showthread.php?t=340557
In your case, activate only the 1.900Mhz band or the 850 / 1900 band only. I believe that the former is better, though.
I've been only using it for the last 2 days, but so far so good.
JP
Click to expand...
Click to collapse
Guys,
Definitely the problem is software. I'm from Brazil and my operator is TIM. I tried many ROMs (at least 10) with the same symptom: if the phone misses the signal, I get into troubles to find the signal again and it keeps finding another operator instead TIM (in my case it only finds Vivo - which is 850Mhz).
After those many trials, I found a ROM that solves the problem partially. It's the PV DVH 19701 ( http://forum.xda-developers.com/showthread.php?t=390008&highlight=19701 )
With this ROM, it still looses the signal when on a place where the signal is not present and don't find while returning to a place which the signal is present, BUT, I just tap the antenna on the top of the screen, tap settings > network and finally tap "find network" and VOILA, the signal is back without much pain!!
One more thing is a little change on the registry according to a recommendation from Microsoft. Using one registry editor, go to:
HKCU\ControlPanel\Phone and change the value for "Features" parameter from 204c7d8 to 206c7d8. Remember that before you change, you need to choose the view mode to hexadecimal.
That's it folks...have fun!

Which Radio ROM for UK T-Mobile MDA Vario II?

Hi all, apologies for posting this, as there I know there's tons of other threads relating to this matter - I've spent quite some time reading (and being confused!) by them, but I can't seem to find a thread which a) has someone describing the exact problem I have, or b) giving a definitive solution. So here it is:
I have a UK MDA Vario II. It's my second one (replaced under warranty), this, and my first one both had a problem where I would seemingly randomly not receive calls or texts. The phone shows it has a signal, and the green light would be flashing to indicate service. However, on occasions, if you try to ring the phone, it diverts straight to voicemail. Sometimes service resumes normally (about an hour later) and I get a message informing me of my missed calls, and sometimes I have to do a soft reset to get it working again.
What I have gathered from reading on these forums is that I may need to upgrade my radio - it had version 1.05.02.00 on it (which it must have been shipped with).
So - following instructions, I put HardSPL 2.10 on to the device, then flashed the Radio ROM to version 1.47.30.10, deciding that this looked the safest bet based on the feedback of other people on the Forum. Having done this (last night) I decided to test the phone once per hour today by just calling it, and I only got to the second test before it failed again - showing signal and green light flashing - but calls going straight to voicemail.
So - I don't want to do any damage to the phone - but I need to know that when someone's calling me, it's going to ring (we're moving house soon, so I'm relying on certain calls from solicitors, bank etc etc). Can anyone tell me of a reliable Radio ROM version for an MDA Vario II on T-Mobile UK? (which won't introduce further problems!)
THANKS!!
broudie said:
Hi all, apologies for posting this, as there I know there's tons of other threads relating to this matter - I've spent quite some time reading (and being confused!) by them, but I can't seem to find a thread which a) has someone describing the exact problem I have, or b) giving a definitive solution. So here it is:
I have a UK MDA Vario II. It's my second one (replaced under warranty), this, and my first one both had a problem where I would seemingly randomly not receive calls or texts. The phone shows it has a signal, and the green light would be flashing to indicate service. However, on occasions, if you try to ring the phone, it diverts straight to voicemail. Sometimes service resumes normally (about an hour later) and I get a message informing me of my missed calls, and sometimes I have to do a soft reset to get it working again.
What I have gathered from reading on these forums is that I may need to upgrade my radio - it had version 1.05.02.00 on it (which it must have been shipped with).
So - following instructions, I put HardSPL 2.10 on to the device, then flashed the Radio ROM to version 1.47.30.10, deciding that this looked the safest bet based on the feedback of other people on the Forum. Having done this (last night) I decided to test the phone once per hour today by just calling it, and I only got to the second test before it failed again - showing signal and green light flashing - but calls going straight to voicemail.
So - I don't want to do any damage to the phone - but I need to know that when someone's calling me, it's going to ring (we're moving house soon, so I'm relying on certain calls from solicitors, bank etc etc). Can anyone tell me of a reliable Radio ROM version for an MDA Vario II on T-Mobile UK? (which won't introduce further problems!)
THANKS!!
Click to expand...
Click to collapse
Ive never had any problems with calls not connecting, the only times it has failed is due to poor reception and ofcourse network busy errors.
I wouldnt worry about the radio version it sounds like a network issue. Have enabled 3G on it??
mrvanx said:
Ive never had any problems with calls not connecting, the only times it has failed is due to poor reception and ofcourse network busy errors.
I wouldnt worry about the radio version it sounds like a network issue. Have enabled 3G on it??
Click to expand...
Click to collapse
I have (and thanks btw - it was your guides that I followed attempting the flash last night). The thing is, a good friend of mine has the same phone, in the same area - and he doesn't get these issues. My other half is also on T-Mobile, but uses a Sony Ericsson and doesn't have any problems with coverage. I'm in a city centre right now, and my house isn't far out - we both have decent reception there.
In fact - an interesting thing just happened (literally..) - I have my phone on a charging cradle, and it had been dormant for a while, so the screen was off. It woke up, as if about to receive a call or text, but then nothing happened... so I called myself from my office phone - and it connected ok.
About 5 minutes later my girlfriend called me up on the mobile, and I mentioned the issue was still there - and she said 'yeah, i tried to call you about 5 minutes ago'.... so it's like the call was received (i.e. the phone new about it), but it didn't complete the process.
I had thought a new radio version might help (from my very limited understanding of such matters) - are you saying that's not the case?
Does 3G affect this too? What can I do - I use the internet more than anything else on my phone....
Thanks
does anyone have any further advice on this?
Mr Vanx? Anyone??
My phone is still randomly losing signal - generally not accepting incoming calls (though today it was not accepting calls, whilst I was still able to make them...). I think I may go and get it replaced by T-Mobile - but I have upgraded the radio to 1.47.30.10, and have put HardSPL 2.10 onto it.
I guess I need to downgrade to original versions, but I can't seem to find a guide which tells me if what I want to do is OK (and how...).
Please - can anyone assist - I believe my original radio rom was 1.05.05.00, and the SPL version was 1.01.
I'm using 1.54.30.10 and it's fine. I found 1.54.00.10 pretty good as well. Much fewer dropped calls comparing to any 1.4x RadioROMs. Signal strenght is also better. The only thing I cannot comment on is the battery life, as I charge the phone every night whether it's 90% or 10%.
mean-machine said:
I'm using 1.54.30.10 and it's fine. I found 1.54.00.10 pretty good as well. Much fewer dropped calls comparing to any 1.4x RadioROMs. Signal strenght is also better. The only thing I cannot comment on is the battery life, as I charge the phone every night whether it's 90% or 10%.
Click to expand...
Click to collapse
did you have the same problems as me? - phone appearing to have a signal but calls being diverted to voicemail... seemingly randomly...
Use GSM mode as default
I have the exact same problem (I travel between Birmingham and London mainly) on my Vario II. It is really fustrating and my wife seems to think I dont answer her calls/txts on purpose(!)
On mine, the problem is due to the 3G mode - when I turn OFF 3G and use normal GSM the problem goes away. I get all calls/txt and internet connections sucessfully. When I turn on 3G the problem comes back - lost calls and unsucessfull internet connections. When in 3G mode sometimes it works somtimes it doesnt
Someone mentioned it could be that it is not switching between 3G and GSM automatically when no 3G is available. However, it happens even when in a good strong 3G area.
I swear this problem did not happen in the early part of my contract but only recently. One theory is that TMobile has sold so many 3G devices now both monthly and pay-as-you-go (esp 3G Data Modems with users using the network for their laptops) that the TMobile cells are just getting overloaded. Also, it could be that TMobile are also doing an upgrade of the 3G network and it is causing problems for users.
So what I do is run the phone in GSM mode as default (so no missed calls/txt and use Opera Mini for quick web surfing works well in GSM mode) Then switch on 3G mode if I am going to do any web surfing for more then 5 mins.
The added side benefit is also much much better battery life in GSM mode (3G soaks up the juice very quickly). I never use video calls ect so no loss there.
My Comm Manager has a toggle for 3G/GSM mode so I use that to quickly change between the 2 modes.
In Summary I would rather have a reliable phone for recieving/making calls then one which is hit and miss.
btw, Im now due an upgrade - wondering if I should stay with TMobile or not...
We appear to have the same phone 'lives'!
kismat1970 said:
I have the exact same problem (I travel between Birmingham and London mainly) on my Vario II. It is really fustrating and my wife seems to think I dont answer her calls/txts on purpose(!)
Click to expand...
Click to collapse
Same here - we're in the middle of selling 2 properties and buying another one, so I could really do with not having the phone playing up.
kismat1970 said:
On mine, the problem is due to the 3G mode - when I turn OFF 3G and use normal GSM the problem goes away. I get all calls/txt and internet connections sucessfully. When I turn on 3G the problem comes back - lost calls and unsucessfull internet connections. When in 3G mode sometimes it works somtimes it doesnt
Someone mentioned it could be that it is not switching between 3G and GSM automatically when no 3G is available. However, it happens even when in a good strong 3G area.
Click to expand...
Click to collapse
I've tried this today, and have been testing the phone on an hourly basis - so far so good.
kismat1970 said:
I swear this problem did not happen in the early part of my contract but only recently.
Click to expand...
Click to collapse
Spot on - this definitely was not a problem when I signed up (Nov 06).
kismat1970 said:
So what I do is run the phone in GSM mode as default (so no missed calls/txt and use Opera Mini for quick web surfing works well in GSM mode) Then switch on 3G mode if I am going to do any web surfing for more then 5 mins.
Click to expand...
Click to collapse
Do you know where I can get a reliable version of Opera Mini?
kismat1970 said:
My Comm Manager has a toggle for 3G/GSM mode so I use that to quickly change between the 2 modes.
Click to expand...
Click to collapse
I dont have this option in mine? How can I get it??
kismat1970 said:
In Summary I would rather have a reliable phone for recieving/making calls then one which is hit and miss.
btw, Im now due an upgrade - wondering if I should stay with TMobile or not...
Click to expand...
Click to collapse
Ditto - im due for upgrade in March, and had been looking at the Vario iii - but am now wondering if I should be looking at another network? Is this a consistent problem with all 3G devices on T-Mobile - or does it just affect the Vario ii?
broudie said:
Same here - we're in the middle of selling 2 properties and buying another one, so I could really do with not having the phone playing up.
I've tried this today, and have been testing the phone on an hourly basis - so far so good.
Spot on - this definitely was not a problem when I signed up (Nov 06).
Do you know where I can get a reliable version of Opera Mini?
I dont have this option in mine? How can I get it??
Ditto - im due for upgrade in March, and had been looking at the Vario iii - but am now wondering if I should be looking at another network? Is this a consistent problem with all 3G devices on T-Mobile - or does it just affect the Vario ii?
Click to expand...
Click to collapse
I signed up in Sep 06 and there was no problem with 3G mode then (problem free for the first 12 months at least).
From your phone internet rowser goto http://mini.opera.com/ and click on Download Opera Mini (this is latest version 4).
Before you do this make sure you have Esmertec Jbed midlet manager installed (Opera Mini is a Java App).
I use Opera Mini 90% of the time and its still renders fast on a GSM connection.
Ive uploaded the CABs for you for the Midlet Manager and Comm Manager.
I dont know if it only affects the VarioII maybe others can comment. If its a network issue then I would expect it affecting other devices also.
I want to go for the HTC Touch Dual (aka MDA Touch Plus on TMobile) as my next phone but may go with Orange if it is a network issue. Only reason I stay with TMobile is for the 'unlimited' web'n walk tarrif..but if I can't use 3G realiably then what is the point?
kismat1970 said:
I signed up in Sep 06 and there was no problem with 3G mode then (problem free for the first 12 months at least).
From your phone internet rowser goto http://mini.opera.com/ and click on Download Opera Mini (this is latest version 4).
Before you do this make sure you have Esmertec Jbed midlet manager installed (Opera Mini is a Java App).
I use Opera Mini 90% of the time and its still renders fast on a GSM connection.
Ive uploaded the CABs for you for the Midlet Manager and Comm Manager.
I dont know if it only affects the VarioII maybe others can comment. If its a network issue then I would expect it affecting other devices also.
I want to go for the HTC Touch Dual (aka MDA Touch Plus on TMobile) as my next phone but may go with Orange if it is a network issue. Only reason I stay with TMobile is for the 'unlimited' web'n walk tarrif..but if I can't use 3G realiably then what is the point?
Click to expand...
Click to collapse
Thanks very much for loading this stuff...
my other half is after the touch plus too - but have advised her to do some research before committing to T-Mob again.... though if she gets it and it's ok, i'll post some feedback on here...
Cheers
The Touch Plus is a good phone if you can live without Wifi...Ive read somewhere that this problem is dependant on the area you are in ...in particular the TMobile cell tower servicing the area you are in and it is possible to phone TMobile tech support to get an engineer to investigate and correct the problem. In my case that would be my home address and my work address - maybe worth a try?
Just to add my 2p worth... my radio is 1.05.05.00 (came on the phone, which was a replacement for the first which had the screen drift)... I've had occasional times when the phone's lit up but nothing's happened, but I usually chalk that down to the phone doing an activesync check for push mail, and as there's nothing there, it goes back to sleep.
To my knowledge, I've not really missed any calls or anything like that since way back last year - when sometimes I'd be sitting in the same café as a mate also on T-Mobile, and we'd do the you-call-me-i-call-you thing to get each others' numbers - and it'd go straight to voicemail! That was quite amusing.
Nobody's told me that they've had problems trying to reach me on my mobile though for a fair while now, so I'd almost completely forgotten about this problem!
edit: yay, 500th post! Took a while but got there eventually... Anybody want to sponsor me with a free Kaiser?
broudie said:
Can anyone tell me of a reliable Radio ROM version for an MDA Vario II on T-Mobile UK? (which won't introduce further problems!)
THANKS!!
Click to expand...
Click to collapse
Hi, I confess I haven't read the thread in great deal (am in a rush and am just passing through!) but you could try this official T-Mobile UK ROM. It's Windows Mobile6 and Radio 1.50.xxx (as far as I remember). The main thing is that it's official, and includes their latest sanctioned bootloaders etc. I flashed it to mine before taking back for warranty (as it's not possible to go back to the old 1.05 radio from recent unauthorised versions).
T-Mobile UK WM6 complete MDA Vario II ROM:
http://member.htc.com/ruudownload/t-mobile/TMobileWM6Step1-TMuk.aspx
sim
:O when did that become available? I swore to myself I'd keep an eye on the TM phone downloads site because I knew WM6 was available for some devices, but I completely forgot and since then they've rolled out WM6 for my phone... Which is a proper pain, but at the same time a really nice surprise.
Hard reset your device, install ALL applications on the phone (nothing on the micro SD - except outlook attachments). This should solve the problem.
sahuja said:
Hard reset your device, install ALL applications on the phone (nothing on the micro SD - except outlook attachments). This should solve the problem.
Click to expand...
Click to collapse
Why dig up this old thread and answer a question that has probably long since been resolved?
Wam7 said:
Why dig up this old thread and answer a question that has probably long since been resolved?
Click to expand...
Click to collapse
It's been useful for me. I'm having exactly the same experience on orange with an spv m3100 at the moment. This helps.
Dear,
My trinity (HERM300) test device have the same problem:
No CID, NO RADIo , NO GSM, NO IMEI
This info on my device (when having problems)
HERM300
IPL 1.04
SPL 2.10
plz plz plz any body help me for this ...........
john7992 said:
Dear,
My trinity (HERM300) test device have the same problem:
No CID, NO RADIo , NO GSM, NO IMEI
This info on my device (when having problems)
HERM300
IPL 1.04
SPL 2.10
plz plz plz any body help me for this ...........
Click to expand...
Click to collapse
you should check and find its at http://forum.xda-developers.com/wiki/index.php?title=Hermes_ExtractedRadioRoms

Using Vario II on Three problems when dropping back to Orange/EDGE

Hi
Firstly apologies if this is the wrong place: I don't know if I should be posting this in the WM6 forum or if it's unrelated to the upgrade, but I'll start out by stating I have Schaps 4.31 installed along with 1.54.07 radio
I moved to three when my T-mobile contract expired and everything has worked fine until, this week, I took a trip down to Cornwall (no 3g signal anywhere, pretty much). So it's dropped down to 2G, which usually works fine. However here as soon as I transfer TCP data it fails (SSH, Web, IMAP all just stop).
DNS lookups work fine, so I'm assuming the connection is working fine, but I just can't seem to transfer anything. Three won't help me because I'm not using a three phone (grrrr); I found a message on a forum which said three requires a WAP proxy set up for the internet connection but a) it made no difference when I set it and b) wouldn't that have stopped it working before now?
So I'm pretty-much stuffed.
Other things to note: this version of the ROM + Radio keeps telling me I'm roaming when it drops down to 2g (very irritating but hasn't caused me problems at home).
Has anyone seen this before? Any suggestions?
Thanks!!
Geoff

Categories

Resources