Just Smashed my USB Connector for My HTC P3600
Can any one tell me where to buy a new one?
I already took it out it have 11 Pins .
Thanks
Related
Got my TP from a friend and it works OK, but the pins on the USB connector were bashed in. I can get an insurance replacement for the $100 deductible but was wondering if there is a source for the USB jack and if it's a reasonable DIY repair.
Any thoughts?
My usb jack is also broken. need to replace a new one
WHERE TO BUY?!?!
Hi to all,
I've had my motherboard replaced by HTC due to phone stucked on white screen at the boot (very fast I must admit. Last monday I send it and today I received it repaired, I hope). One question if someone has the answer. With MB they have replaced usb connector for charge too ? I've the nightmare that connector may be damaged wiring and unwiring cord for charge. So I'll be more happy to know that the connector too is new. I've had the connector broken after two months with an old samsung and they didn't repair it because said that I've had broken it.
I'm thinking to buy a powermat......
Thanks
Hi,
my screen broke about 5months ago. So i bought a new digitizer to replace it but after I soldered and installed it, the touch screen didnt respond. So I sent back the digitizer for another one and same thing happened.
Then I bought a screen + digitizer already soldered and tried to replace it but same thing.
When the screen was broken the touch screen still worked, weird uh?
Any idea?
Probably in the process of removing the old digitizer... the female connector on the board that connects to the flex cable of the digitizer might be broken... so my guess... you might need a new board
kompheak said:
Probably in the process of removing the old digitizer... the female connector on the board that connects to the flex cable of the digitizer might be broken...
Click to expand...
Click to collapse
In fact, it's affected some soldering point(s) of the female lcd connector on the motherboard: some skilled service guy can fix it ( worse case scenario you'll have to replace connector!).
Ok I will try checking the connector. Thx
Sent from my HTC Sensation XE with Beats Audio using Tapatalk
TecHunter said:
Hi,
my screen broke about 5months ago. So i bought a new digitizer to replace it but after I soldered and installed it, the touch screen didnt respond. So I sent back the digitizer for another one and same thing happened.
Then I bought a screen + digitizer already soldered and tried to replace it but same thing.
When the screen was broken the touch screen still worked, weird uh?
Any idea?
Click to expand...
Click to collapse
Yes, a lot of chinese Producs ( i bet you ordered all from HongKong ) aren´t working out of the box. Often this Parts are not only Cheap; no....they are Produced only for the Trashcan...
It´s not easy to find a Reseller they sell good and working Parts !
Best Regards and good Luck !
Micha
hey everyone... can anyone here can link me a good Xplay white housing and main flex cable off ebay
if the flex cable is the problem with my fone then i'll buy it and then change the housing
The microusb port on my n7 2012 isn't working anymore... Is there any way to charge it without the micro usb port?
use a dock, good luck finding one at this point.
alternatively repair or replace the usb port. a repair can be done with some rosin core solder and a soldering iron. you simply reshape the metal part of the connector and apply solder to the joint where the pieces of the metal meet. havent had an issue since i did that.
Buy another USB port/headset adapter from EBAY, they cost like $15 I've broken about 4 of them and its very easy to replace. You remove the back cover, lift out the battery and disconnect it. You don't need to solder anything if you just get a new port.
http://www.ebay.com/itm/USB-Power-C...844?pt=LH_DefaultDomain_0&hash=item23449c1ff4
I used this one on my N7, less than $10 - worked great, and as mentioned above, you just need a small screw driver.