Does anyone know how to get the clear lens bezel/cover that snaps into the upper rear housing? Mine is scratched. When disassembling the cover over the camera the only part needing to be replaced is a clear plastic disc/protector that snaps into the cover (and with the small rubber ring gasket seals dust from the board mounted camera/lens). After searching for 8125 replacement housings (ebay, here at xda, etc.) this small clear disc appears to not be included with the rear upper cover.
*BUMP*
My camera lens appears to have fallen off. Does anyone know where I could find a replacement? Thanks!
Related
Hey guys I was searching up on the forums about replacing the covers on the Jam after I dropped mine the other day, and after seeing the post by adolfotregosa:
http://forum.xda-developers.com/vie...ays=0&postorder=asc&highlight=housing&start=0
I decided im just going to spray paint the case black.
I found the PDF file about removing the back and side casings to fix a speaker issue, but I havent come across anything that explains how to remove the front cover, and the lcd from the front cover.
Can anyone shed some light on how to do this?
PDF file speaker issue
Can you please give me the link to the
"PDF file about removing the back and side casings to fix a speaker issue".
Cheers mate....
http://forum.xda-developers.com/viewtopic.php?t=18384&highlight=disassemble
After removing the flat cable as in page 15/16, right under the flat cable there's some clip you need to push towards outside. It suppose to come off completely. When that's off you can pop the screen. I needed to use some force but not as much to break it
just remember, AT YOUR OWN RISK!
Hi,
is there any manual how to open the TyTN?
My screen was scratched and i bought a new one on eBay - but i dont't know how to open the front-cover. Is it a problem?
thx
ironfit said:
Hi,
is there any manual how to open the TyTN?
My screen was scratched and i bought a new one on eBay - but i dont't know how to open the front-cover. Is it a problem?
thx
Click to expand...
Click to collapse
See the Wiki site on this forum:
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
and this Japanese site for dismantling:
http://inuchanbt.blog54.fc2.com/blog-entry-100.html
and my humble site with some more pics and downloadable TyTn Service Manual.:
http://michael-channon.spaces.live.com/
Mike
What I am curious about is where did you find a TyTN replacement display...
I had no luck finding one and resorted to sending my device to HTC in the UK for (expensive) repair.
The basic steps for opening the phone.
(This is a rough description from my memory...)
1. Remove the back cover, battery, sim, SD card etc...
2. remove four screws using torx 6 screwdriver from back (1 is in the corner in thel anyard loop and one is under the warranty "void" sticker)
3. Work your way around the grey plastic part you have just unscrewed until it snaps off.
4. Remove a 5th torx screw in a well right next to the camera lens
5. remove full electronics board - it will be attached on the bottom with a connector covered with tape - carefully remove the tape until you can unplug the connectorized ribbon).
6. Unscrew 4 Phillips screws to remove the bottom tray from the display assembly (slide ribbon through the hole)
7. Unscrew 4 phillips screws from display assembly corners
8. Work your way around the rim with a tiny flat screwdriver - unless you have a special plastic tool for this (careful not to bruise the plastic) to open the display assembly
9. Remove 2 phillips screws holding the PCB underneath the display and one from the board above the display
10. disconnect the display ribbon (may be under some yellow tape) from its connector in lower left corner (looking from the back) by lifting the latch part and pulling the ribbon out.
11. Unhook the display with the electronics and peel some sticky electronics from the display back.
12. Reverse these steps with the new display...
Let me know if this help / you have questions.
an some one please tell here is the magnet from inside the casing, that makes the screen auto rotate?
Is it a small metal piece near de front camera inside front house case???? if not here is it?
thanks
If there a teardown guide for the Wildfire? I'm planning on replacing the fascia to a black or white one
I googled it and I found the EVO and the Desire...
Thanks.
nicky041192 said:
If there a teardown guide for the Wildfire? I'm planning on replacing the fascia to a black or white one
I googled it and I found the EVO and the Desire...
Thanks.
Click to expand...
Click to collapse
Surely its pretty similar to the desire?
IcyWildfire said:
Surely its pretty similar to the desire?
Click to expand...
Click to collapse
It's what I was thinking but I'm not too sure...
I just did a screen replacement on a German Wildfire today, I used a desire guide briefly - but it was pretty simple. 8 screws and 3 ribbons in total isn't to bad for a full teardown.
Here's the brief:
1) remove back battery cover
2) remove battery, MicroSD, and SIM
3) remove 4 corner star screws
4) remove 2 philips screws from right hand rail (sim card side)
5) Unclip bottom bracket and remove
6) Unclip plastic back from both side rails and remove
7) Remove 2 philips screws from bottom right and top left of breadboard
8) Disconnect haptic feedback ribbon from bottom left by lifting the black lever and sliding out the ribbon (very narrow ribbon)
9) Disconnect screen and touch screen ribbons on right hand edge by lifting them up (they're snap-ons)
10) Lift volume board up from between main bread board and volume button
11) remove breadboard from front housing
12) Peel back the bottom ribbon from the back of the screen (it's glued on with light adhesive)
13) Lift up bottom corner of screen and remove screen from front housing
in the end you should have these pieces:
Front housing
Screen
Bread Board
Back Housing
Bottom Plastic Clip
Back cover
2 Small philips Screws (breadboard)
2 large philips screws (back housing right hand edge)
4 large star screws (back housing corners)
Sorry, I literally just finished this an hour ago. Hope this helps.
i tear-down my wildfire like SophT. my big problem is now, to put the new digitizer in the phone. the old was glued and now i didn't have any idea to fix the new in the phone. have anyone an idea ?!
i think i destroyed the new display. on both sides of the new one were a protective sheet. i removed both, the phone works perfectly, but there is no possibility to use the touchscreen. There are no inputs possible. Have I destroyed with the removal of the film, the new display?
w1st said:
i think i destroyed the new display. on both sides of the new one were a protective sheet. i removed both, the phone works perfectly, but there is no possibility to use the touchscreen. There are no inputs possible. Have I destroyed with the removal of the film, the new display?
Click to expand...
Click to collapse
I'm okay with this and I think it's hilarious.
Hi,
For all those who have the black screen during call/ windows button not responding issue try this. It is a tech repair, so if you're not comfy dismantling your device take it to a pro.
I've had some spare time to repair an Omnia7 for a friend [ I was acting middle man between Samsung and him]. Sammy serviced the device 4 times and changed everything ( the mainboard, the sensor, AMOled screen) but the problem kept on showing up.
I have traced the fault to the fact that the sensor is pushed to the right by the ribbon attached to it and thus acting wrong. The tape that is supposed to keep it firmly attached is getting weak in time and allows this migration.
Steps:
1. Take apart your phone. Simple job. Remove battery&sim card. Upper cover pops out, 3 screws. Slide out the back. 2 screws at the bottom and the bottom comes off. 2 screws under that cover and the antenna+mic comes off. 2 middle screws for the plastic piece. 1 silver screw for the upper speaker module. 2 silver screws for the mother board. disconnect 2 connectors (1 up for camera and 1 down for buttons)remove mother board carefully ( lift up a bit the vibrator, volume, I/O and camera buttons. they are attached with double sided tape, disconnect the Screen- it's under mb).
2. Take a look at the sensor PCB. I bet it's moved in opposite of the side where the connection ribbon is. You need to realign it. Lift the earpiece and jack. they are connected to the proximity/ ambient light sensor. Should come out fairly easy,it's only double-sided tape. Realign it with in a fashion that leaves at least 1 mm from the side.
There are different ways to make sure the problem does not appear again. Hot glue- just a droplet , piece of plastic, better double sided tape. Choose whatever you like.
3. Reassemble the phone.
Also, see photos attached. Notice how off centered was the sensor PCB
Lol, man its working
THX