I am new here please help me, i have i-mate PDAL and when i power on phone without sim it asking for password how to remove password?
i think no body know
Hardreset the unit. Check the XDA-Wiki (link on top of this page) on the procedure how to hardreset your phone.
ENJOY!!
To hard reset, hold down the two soft key buttons directly below the screen, and press the reset pin.
You will be presented with a menu saying 'press R to reset, X to exit'
Phone must be powered on without sim card
hanmin said:
Hardreset the unit. Check the XDA-Wiki (link on top of this page) on the procedure how to hardreset your phone.
Click to expand...
Click to collapse
please give me link
done thanx to allzzzzzzzz
Related
Hi all,
I have dead JASJAR dead after ROM UPDATE.
I cannot enter bootloader menu.
Please any help
Thanx in advance
BR
Julian
If you don't mind explaining more detail on the step that you have done on flashing your universal, maybe someone can come up with some help.
bambacik said:
If you don't mind explaining more detail on the step that you have done on flashing your universal, maybe someone can come up with some help.
Click to expand...
Click to collapse
Here is little explanation about upgrade process;
I upload firs and second file and it was 100 % success, but when I upload the third file in the middle something happen and message appears " restart your device" or somethink similar.
After that device dies, I try all combinations for HARD RESET and BOOTLOADER menu but without success.
Please any HELP
BR
Julian
Press camera+power and soft reset and check if it get into bootloader where u serial top.
hdubli said:
Press camera+power and soft reset and check if it get into bootloader where u serial top.
Click to expand...
Click to collapse
not working this combination any other ideas ?
Thanx in advance
Not camera+power+reset, but backlight+power+reset.
bambacik said:
Not camera+power+reset, but backlight+power+reset.
Click to expand...
Click to collapse
Same ... I tryed all the combinations to enter bootloader, but... no success
BatRambo said:
Hi all,
I have dead JASJAR dead after ROM UPDATE.
I cannot enter bootloader menu.
Please any help
Thanx in advance
BR
Julian
Click to expand...
Click to collapse
A) Plug your phone into your computer via USB.
B) Press the Power and the light button, not the camera.
You should see a faint outline that says USB.
It's now recognized in the Device Manager, run your ROM Update and fix it now.
Where is the "light" buttom? Please.
BatRambo said:
Hi all,
I have dead JASJAR dead after ROM UPDATE.
I cannot enter bootloader menu.
Please any help
Thanx in advance
BR
Julian
Click to expand...
Click to collapse
I had the same problem b4:
try this:
1) plug the usb cable in 1st
2) soft reset the imate (the screen should have a very light "USB" word)
3) run the rom update on the PC
4) after completion, hard reset (press the 2 "-" buttons on the imate) and press the soft reset bottun together.
5) when the screen is re-set, press "X" to exit instead of "0" to go to factory default.
still no solution
only jtag solution can turn on the phone
and i think its possible only in service center
I have a qtek S200:
IPL 2.09
SPL 2.09.0000
GSM 02.07.20
OS 2.13.9.26
I have a problem, y qtek starts and goes until the "windows Mobile" Screen and then it stop.....and it stays in that screen for ever.........please help me out, i tried to hard reset and it doesn´t work what should i do?
Help me please!
What was the last thing you did before it stopped working?
Did you install something?
Are you sure you preformed hard reset? You must hold power + camera + comm manager buttons (all on the sides) then press and release the reset hole (at the bottom).
Then you will see a question asking you to confirm hard reset. If I remember correctly you need to press 'send' (the green phone button) to preform hard reset.
Please be sure to read the instruction on he screen.
See the wiki:
http://wiki.xda-developers.com/index.php?pagename=Flash_From_Bootloader
You have a G3 device, so make sure if you use a RUU, you use a G3 specific one.
levenum said:
What was the last thing you did before it stopped working?
Did you install something?
Are you sure you preformed hard reset? You must hold power + camera + comm manager buttons (all on the sides) then press and release the reset hole (at the bottom).
Then you will see a question asking you to confirm hard reset. If I remember correctly you need to press 'send' (the green phone button) to preform hard reset.
Please be sure to read the instruction on he screen.
Click to expand...
Click to collapse
thanks man it works, thank u a lot
Hi everyone,
I recently received an XDA Orbit 2, literally, charged it for 2 hours, and when it was full charged, I started using it, I had it for about 2 months now, and recently I changed my home Internet connection to wireless (It's a B & G connection) so my laptop connects fine, and when I tried to connect my XDA Orbit 2, it connected and then soft-reset itself, and now it just loads the O2 screen, then Windows Mobile screen with the volume controller and I can't do anything else so here's what I have tried so far:
- Soft reset
- Removed battery and SIM
- Since I can't access phone's menu at all, I tried to Hard Reset method by holding the 2 soft key, reset, and the power button - So I get the warning that everything will be lost and to press 'Send' to continue, so I press the green key, and soft resets and goes back to the same situation again.
- The latest thing I tried is to load the Hard-SPL into the SDCard which has been formatted to FAT32, so loaded the POLAIMG.nbh into the root. and loaded the phone into BootLoader mode (Camera and reset buttons). It loads the memory card and just says 'Loading ... ' I left it for about an hour, until the battery died completely (I'm sure it's not supposed to take that long). And still the same problem.
I'm not sure if this phone is now bricked, can anyone help me plesae. I really need this to start working again, I don't have any info. on it. (Everything was sync. previously).
Kind regards,
Since you havent really messed with SPL, i would say to take it back, since its still into warranty.
Thanks for the reply, I'm not actually in the UK and will be overseas for a while. I don't really mind experimenting so I would appreciate any advise on this matter. Thanks again.
htctytnowner said:
Thanks for the reply, I'm not actually in the UK and will be overseas for a while. I don't really mind experimenting so I would appreciate any advise on this matter. Thanks again.
Click to expand...
Click to collapse
I assume just boots into bootloader and then stays there?
If yes you culd try searching out a thread on MTTY and recovery from boot loader but I dont know how well that would work on polaris as I have not tried it yet.
HTH
Leon
Thanks for the reply, I heard about the MTTY process, but I've no clue on how to do it, since the phone can't connect in ActiveSync mode. Is there a thread or WiKi guide out there?
htctytnowner said:
Thanks for the reply, I heard about the MTTY process, but I've no clue on how to do it, since the phone can't connect in ActiveSync mode. Is there a thread or WiKi guide out there?
Click to expand...
Click to collapse
Only in the ELF forum
Here:
I'm pretty sure you can download MTTY from here and read through how to use it.
http://forum.xda-developers.com/showthread.php?t=347700
Also it is worth checking the wiki and searching
http://forum.xda-developers.com/showpost.php?p=2054848&postcount=38
Please do some research! I have not done this before and I have no idea what the commands do!!!
pqillu said:
You can try this:
Originally Posted by christonge
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
THX to christonge
Good luck.
PQillu
Click to expand...
Click to collapse
Please Heeelp!
I wa installing a rom from todopdas.es an my Polaris doesn´t pass from the screen where´s said "smart mobility", and R1.58.21.23 G 25.65.30.04H D 1.52.00.00, please what I can do?
You need to do Hard Reset, all information will be wiped off. To do hard reset, hold down the:
1.Press and hold the GPS/MESSAGING and INTERNET EXPLORER
buttons, and at the same time, use the stylus to press the RESET
button at the bottom of your device.
2. Release the RESET button, but
continue pressing the GPS/
MESSAGING and INTERNET
EXPLORER buttons until you
see this message on the
screen:
This operation will delete
all your personal data,
and reset all settings
to manufacturer default.
Press Send to restore
manufacturer default, or
press other keys to cancel.
3. Release the buttons, and then press SEND on your device to perform
the hard reset, or press any other button to cancel the reset.
Good luck.
Hi,
I'm using an HTC TC POLARIS100. Today I upgraded my ROM and SPL successfuly. If you're still in trouble and believe the same process will help, I will let you know the process followed.
GUY
pls help me sir to unlock my mwg atom v password coz my brother put a password on my phone nd he cant remember the code pls help me sir.i already try this method .You can remove password by doing a hard reset.
To do hard reset. Press Power and hold at the same time poke into soft reset hole by stylus.
but it still same i want to unlock my mwg password is there other way to unlock or reset my mwg atom v password
i also had a similar type of problem. but it got removed by hard resetting. are you sure you are doing it properly. if you have done hard reset properly then after restart you'll be asked to "adjust screen positioning/tapping", "tap & hold to cut/paste" etc.
to try hard restart
Hi,
My 3400 is not starting. When i start the phone it hangs up in the "windows mobile direct push technology" screen. I tried without SD card and SIM but no luck. I have all my contacts inside and I need them. How can I fix the problem of my phone. Please help.
ONBL 1.10.0000
SPL 1.10.0000
GSM 2.79.90
OS 1.10.0.0
-aneesh
aneeshnr said:
Hi,
My 3400 is not starting. When i start the phone it hangs up in the "windows mobile direct push technology" screen. I tried without SD card and SIM but no luck. I have all my contacts inside and I need them. How can I fix the problem of my phone. Please help.
ONBL 1.10.0000
SPL 1.10.0000
GSM 2.79.90
OS 1.10.0.0
-aneesh
Click to expand...
Click to collapse
i don't think u can save ur contacts now
just hard reset ur device but all data will be lost.
How to do the hard reset? please tell me.
no way to save data?
Hi,
I searched google and got the method to hard reset.
-------------
To perform a hard reset (Full Reset) press and hold the left SOFT KEY and the right SOFT KEY, and at the same
time, use the stylus to press the RESET button at the middle left side of your device.
Release the stylus, but continue pressing the two SOFT KEYs until you see the following message on the screen:
This operation will delete all your personal data, and reset
all settings to manufacturer default. Press Send to restore
manufacturer default, or press other keys to cancel.
Release now the two SOFT KEYs, and then press the TALK (Send) button
---------------------
But when I press the reset button phone restarted but nothing siplayed as mentioned above. Again it went to windows screen and hung there! Cant even do hard reset? What can I do now? Please hlep.
It is ok now. thanks
aneeshnr said:
It is ok now. thanks
Click to expand...
Click to collapse
its nice to hear that ur device is working .
enjoy!!
I was update my htc p3400i ROM, after completion. Phone turn off but not restart, if I try camera button and reset button only green and red right blink not any indication shown on screen,…please help me.
I shall very thankful, if you solve my problem
Sanmukh singh
MSL, Mumbai.
sanmukhsingh said:
I was update my htc p3400i ROM, after completion. Phone turn off but not restart, if I try camera button and reset button only green and red right blink not any indication shown on screen,…please help me.
I shall very thankful, if you solve my problem
Sanmukh singh
MSL, Mumbai.
Click to expand...
Click to collapse
which rom u have updated??????????
hi deepav84,
i was updating this rom "RUU_Gene_hTC_Asia_India_1.17.720.1_4.1.13.34_02.79.90_Ship" after 100% complete it turns off , but not start only Green and red light flash during press reset button...
i was try all methods,#remove batery 20 sec and then start with camer button & both camera and voice button, nothing shown in USB in PC. but result is same...
please help how i can recover my device.....