i have a m600 its about 3 month old, just done a factory hard reset after having many problems getting it to stay on, after about a hour of ****ing about with the mains charger it decided to turn on, however just kept on rebooting, back to the boot screan, not the 3 clolred boot menu, but the orange start screen with numbers like 2.1.001? however now it has been stuck on the blue windows mobile screen for 5 mins and not changed, it is pluged in to mains but i have no lights ilununated not green or orange or red? i know this is a long shot but any ideas befor i smash it through my local orange shop window?
I think the solution is use mtty tool doing format the DOC is OK
MANH Fone said:
I think the solution is use mtty tool doing format the DOC is OK
Click to expand...
Click to collapse
WHaat does it mean ?
MY phone is stucked too at the screen where
ip 2.10.0001
Spl 2.10.0001
Gsm 02.07 .20
Os 2.10.1.30
are after a tentaive of changing ROM.
Merci
Ciao
Stef
feffo said:
WHaat does it mean ?
MY phone is stucked too at the screen where
ip 2.10.0001
Spl 2.10.0001
Gsm 02.07 .20
Os 2.10.1.30
are after a tentaive of changing ROM.
Merci
Ciao
Stef
Click to expand...
Click to collapse
Ola,
just for info.
I made a big mistake detaching the cable during tentatve of CID unlock
My SPV M600was dead ....
Thanks to deep investigation mainly on his forum I found the solution:
Hard reset the M600: Photo button + COmm Manaer buttor + stylo in the ole near usb connector (soft reset),
releasing first the comm button, leving photo button pressed
this leave you in a multicolor screen with usb written in the bottom left (if connected to PC)
then I run the ROM updater that I found here:
http://forum.xda-developers.com/showthread.php?t=297489&page=3
In 10 minutes it as reborn, and I was happy again
Ciao ciao
MANH Fone said:
I think the solution is use mtty tool doing format the DOC is OK
Click to expand...
Click to collapse
How 'bout all task? Can you show me ?
Hi i have the same problem i updated my M600 when i went to charge it no lights came on and the fone failed to come on i have tryed to do a hard reset and a sort reset but the fone just looks dead any advice plzzzzzz?
yeah, try turning it off, or remove the battery. Then hold the camera button. Then insert USB. Phone should show bootloader (3colour screen). You can now flash official RUU.
have some on try to flash a original rom with IPL/SPL/Radio Rom/OS?
Related
ok i think iv killed my m600
i flashed it with the older imate rom the 1.0.9 version
it installed 100% and rebooted and from ther it was stuck on the imate screen for like 10 minutes and i see the following text in red on the top left corner
---------------------
IPL 2.10.0001
SPL 2.15.0001
GSM 01.14.20
OS 1.0.9.25
-------------------------
i tried removing the battery and restarting the fone. still the same thing. can someone please please please help me with this?
what do i do?
im sure orange wont help me out since i flashed it with a non-orange rom.
never mind fixed itby goin into the bootloader
funky_Saggi said:
never mind fixed itby goin into the bootloader
Click to expand...
Click to collapse
hi there i seem to have the same problem as you with the boot screen. top left corner say's
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 1.0.13.21
can you please tell me how you fixed yours please it would be a great help
What you could do is flash it with an newer rom
Hold camera button AND reset (be asure that it hold it while resetting)
Then... you are in you bootloader... connect the PDA with your PC..it will recognized it!
Then run the romupdate ;-)
Hi thanks for trying to help me i got my phone in to the 3 colour screen but my computer does not pic it up at all. is there another way to save my M600
crossy4life said:
Hi thanks for trying to help me i got my phone in to the 3 colour screen but my computer does not pic it up at all. is there another way to save my M600
Click to expand...
Click to collapse
Aren't you getting "USB" written in the bottom left corner of the 3 colour screen when you connect it to USB?
Yes i get the USB come up at the bottom of the screen my computer does not do anything. can you tell me which ROM i will need as the ones i have to run the ROM update but it comes back saying connect to ActiveSync which i can not do is there a way round this?
Final got my SPV M600 Working with the ROM from the download area thanks for the help anyway
cheers
just change the usb port to another one and start rom it should pick it up
Hello,
i tried to update my BA with wm6.
after flashing it stuck in bootloader(blue,green,red,white display) with the line "R 1.10.00" and nothing more...
even hard or softreset do nothing.
what can i do?
ok i even try the Stuck at startup method.
that's the output of Multiport TTY Version:
set 14 0
HTCST ÚÈÒHTCEUSB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>task 0
it always stuck in blue,green,red,white screen after run multiport tool. what can i do?
------------
i have this problem because of this flashing method:
i entered the grey screen (with serial/usb in first line). then i put my usb connection on and run the rom_update. after it is finished (succesfully) it stuck in the blue, green, red, yello screen! help please...
how did you hard reset?
hello,
i hold down the power-button and at same time put stylis in reset.
hard reset for both WM5 and WM6 is different from the one you're doing. here's the guide...
http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
good luck!
ok thanks, i have tried this:
i do softreset. whenn the stripes came i push "records and "camera"(media player button because there is no camera)---> nothing happens. it stops with the line R 1.10.00 and the coloured stripes.
i dont knwo what to do.
the bootloader method is running. i hold power and record button while i softreset. but with color screen it wont work.
they is no camera button (it is media-player button) because there is no camera. its an german xda III (blue angel).
the next problem is i dont knwo what os is right now on it. befor flashing it was wm2003 and flashing says it was successfully. i dont know if its wm6 or wm2003!
ok now all is happen...
the xda says nothing. it dont go on, it dont work anymore. no lights when in cradle, nothing.
can i do anything?
1. Take the battery out, wait a moment, put it back, do not turn on. Put in the cradle and try to charge it. Use power connection (from power supply), disconnect USB from the computer for charging. Amber led should turn on.
2. When it will be fully charged (amber LED will turn off) try to turn it on and enter bootloader. Try to downgrade to WM2003. If it works fine, try again to flash WM5 or WM6.
What you did seems to be wrong update (wrong rom, wrong file, not fully flashed). But you still have bootloader, so it should be possbile to flash it. But you need full battery.
jakubd said:
What you did seems to be wrong update (wrong rom, wrong file, not fully flashed). But you still have bootloader, so it should be possbile to flash it. But you need full battery.
Click to expand...
Click to collapse
it was not unlocked befor i flashed with bootloader-method.
i charged the battery in cradle (withoud the blue-angel). the led first went orange, after a while turned green (fully loaded). put it back in BA an nothing happens. then put BA (with battery) in cradle and the led became red.
no action on devide, no feedback, nothing. it wont turn on but led is still working.!?
jakubd said:
2. When it will be fully charged (amber LED will turn off) try to turn it on and enter bootloader. Try to downgrade to WM2003. If it works fine, try again to flash WM5 or WM6.
Click to expand...
Click to collapse
ok i get it. in display is the "USB" & "v2.07". now i can flash. but my problem is the phone is not unlocked yet. what file can i flash now??
This message tells you are in bootloader mode. Now you can perform normal flash - I would propose you to use tested&working rom (WM2003?). If this works fine, try again to upgrade to WM5/WM6.
BTW: if you disconnect USB (take out BA from cradle) it should show Serial instead of USB.
ok big tanks to the forum. i finally get it. wm6 german on blue-angel!
Same thing here... but worst..
My 9090 is stuck at bootlader...
When i try to update, (i press the power, record and reset), it says:
SERIAL (or USB)
DOC VERSION IS ERROR!
v2.08
Any idea???
that's normal...
try to flash/update your BA in that screen.
the easy way to go into bootloader mode is to execute a file called Enter Bootloader.exe ..it comes with the rom u download..( well it came with xplodes )
Note:- you have to execute this file directly on your deive not on your desktop PC...and i have only tested this on WM 2003..maybe it will work with wm6 also
SilverSamurai said:
that's normal...
try to flash/update your BA in that screen.
Click to expand...
Click to collapse
I there...
I just updated to BA_TMNL_14200_119_11300_Ship, but only with Maupgrade, couldnt do it with baupgrade...
The problem is that i cant put extended rom, whem i try to upgrade is allways an error... and in the settings i dont have extended rom instaled...
Besides that the batery only last 1hour and the PDA is always freezing... i'm always doing resets...
any idea??
Sorry for my bad english by the way...
Hi: This is my first posting and I am new on this board. I have had an MDA that I got as a gift from my Dad and I love it. However, I used it last week and for some unkown reason, it is stuck in the:
'Press Send to Restore Factory Defaults, Other Key to Quit.'
I have been trying to get past this for 4 days and am not having any luck.
I got to the Align Screen and that happened only once. Then I could not get past that. It keep showing the Align Screen and I kept tapping and it just kept going round and round from the Center Tap to the sides and back.
My battery is fully charged, I have read this forum and still I am lost. I would really appreciate any help. Thank you so much.
Toni
Do a Soft Reset or Hard Reset.
Cheers!
zabardast_1 said:
Do a Soft Reset or Hard Reset. Cheers!
Click to expand...
Click to collapse
Thank you for trying to help me. However, I have done both of the resets over and over and I keep getting the same result. 'Press send to restore factory defaults, other key to quit.'
I can get no further than that display regardless of what key or keys that I hit.
I have even tried the two ways of doing a Hard Reset:
1. Hold Com and Voice while pressing Soft Reset Button for 5 or more seconds until I get that display.
2. Hold Com, Voice and Camera while pressing Soft Reset Button for 5 or more seconds until I get that display.
I cannot get past that display regardless of what key or keys I press.
It seems frozen at that display point.
Tried again this am to hard reset my MDA. Now it goes and shows the T-Mobile screen with the IPL/SPL etc. Then goes into Windows and to the Align Screen and for some reason will not recognize the Screen Tapping to align the screen.
I did try to use my PC to recognize the MDA, but it would not. Downloaded WST and that would not recognize my MDA either. I understand that until I get past the Hard Rest my MDA will not be recognized by my PC due to ActiveSync being requried to connect my MDA to the PC. I don't know what else I can try. Search all day yesterday and could not find any solutions. Will continue today. Any suggestions, Please. Thank you.
Tonis said:
Tried again this am to hard reset my MDA. Now it goes and shows the T-Mobile screen with the IPL/SPL etc. Then goes into Windows and to the Align Screen and for some reason will not recognize the Screen Tapping to align the screen.
I did try to use my PC to recognize the MDA, but it would not. Downloaded WST and that would not recognize my MDA either. I understand that until I get past the Hard Rest my MDA will not be recognized by my PC due to ActiveSync being requried to connect my MDA to the PC. I don't know what else I can try. Search all day yesterday and could not find any solutions. Will continue today. Any suggestions, Please. Thank you.
Click to expand...
Click to collapse
Use the love rom to set phone back to "zero". Therefore you must press press the voice and camera buttons if joy reset youre phone.
You get some collored bloks om youre phone and then you can use the love rom.
After that you can use youre original rom updater
sleurhut said:
Use the love rom to set phone back to "zero". Therefore you must press press the voice and camera buttons if joy reset youre phone.
You get some collored bloks om youre phone and then you can use the love rom.
After that you can use youre original rom updater
Click to expand...
Click to collapse
Did a search for Love Rom and Wizard_Love ROM and only came up with 103 results consisting of some Threads with 1570, 898, 618,787, 893, 464........postings on the first page for Threads 1-25.
Now I do have a Red, Green, Blue, White Screen with RUU in the top right corner of the Red Bar with IPL 2.26 and SPL 2.26 in the Red Bar. Nothing is in the Green, Blue or White bar.
I tried to Hard Reset and Soft Rest and nothing happens. I removed my Battery and then tried again and still nothing happens?
Where can I find Wizard_Love ROM and what do I do when I find it. My PC will not recognize my MDA and I used WST and that cannot located my MDA.
I am at a complete loss of what to do next.
Thank you in advance for taking the time to try to help me get my phone operational.
sleurhut
Use the love rom to set phone back to "zero".
do not confuse guys with this statement.Wizard_love_Rom is a patched rom which is flashed to recover back the phone in some stuck up phones,but it doesn't set the phone back to 'ZERO',but its an italian language rom.
Tonis
The multicolor screen is the bootloaders with IPL/SPL 2.26 displayed,this is the mode from where you can flash another rom.There's no need to get the phone activesync,cuz it won't activesync in bootloaders.But when in bootloaders,connect the phone with pc via usb cable and watch small usb appear at the bottom of the bootloaders,if its there then you are good to go and can flash a rom.
Now,download the official T-mobile 2.26 from the link below and get the phone in bootloaders,check usb appear at the bottom and flash it to recover back to the default status of the phone.
http://forum.xda-developers.com/showthread.php?t=342744
Cheers!
zabardast_1 said:
sleurhut
Use the love rom to set phone back to "zero".
do not confuse guys with this statement.Wizard_love_Rom is a patched rom which is flashed to recover back the phone in some stuck up phones,but it doesn't set the phone back to 'ZERO',but its an italian language rom.
Tonis
The multicolor screen is the bootloaders with IPL/SPL 2.26 displayed,this is the mode from where you can flash another rom.There's no need to get the phone activesync,cuz it won't activesync in bootloaders.But when in bootloaders,connect the phone with pc via usb cable and watch small usb appear at the bottom of the bootloaders,if its there then you are good to go and can flash a rom.
Now,download the official T-mobile 2.26 from the link below and get the phone in bootloaders,check usb appear at the bottom and flash it to recover back to the default status of the phone.
http://forum.xda-developers.com/showthread.php?t=342744
Cheers!
Click to expand...
Click to collapse
Thank you again for your help. Prior to this posting I found:
epimazzo Posting at: http://forum.xda-developers.com/showthread.php?t=294107&highlight=bootloader #1 and this is what cleared up my problem and now my MDA is running GREAT!!!!!!!!
This was the same thing that you posted for me, too.
Maybe some of you are already aware of this procedure, maybe not.
Anyway, it worked for me and I decided to share how to do it. Simple.
This procedure should only be used in case you really need enter into a bootloader mode (Red, Green, Blue, White Screen) and all other ways to do it has failed! Hold Camera button is one of these I am mentioning.
1. Make sure your Phone is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your Phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t use the IrDA or Bluetooth for the Upgrade)
4. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
So, Thank you all for your time and help. I do hope this helps others to find a way to correct their problems.
Thanks !
Yes.thats exactly what I wanted you to do
I'm glad you got it up and running fine
Cheers!
zabardast_1 said:
sleurhut
Use the love rom to set phone back to "zero".
do not confuse guys with this statement.Wizard_love_Rom is a patched rom which is flashed to recover back the phone in some stuck up phones,but it doesn't set the phone back to 'ZERO',but its an italian language rom.
Tonis
The multicolor screen is the bootloaders with IPL/SPL 2.26 displayed,this is the mode from where you can flash another rom.There's no need to get the phone activesync,cuz it won't activesync in bootloaders.But when in bootloaders,connect the phone with pc via usb cable and watch small usb appear at the bottom of the bootloaders,if its there then you are good to go and can flash a rom.
Now,download the official T-mobile 2.26 from the link below and get the phone in bootloaders,check usb appear at the bottom and flash it to recover back to the default status of the phone.
http://forum.xda-developers.com/showthread.php?t=342744
Cheers!
Click to expand...
Click to collapse
I does everything you do but
I don't have the cradle :S
so that means a problem?
or there a nother way?
Hi!
I got an mada vario 4. How can I upgrade the rom on it? Or can I change the t-mobile touch flo to manila 2.5? Thx! Zoli
I flashed my htc elf (t-mobile touch) with onyx ultimate, just over halway it froze, then my whole pc froze and crashed, the phone turned off and i havent been able to get it on since, no lights, no screen, nothing
PLEASE HELP
I have tried:
power button
soft reset
hard reset
bootloader mode
plugging it into my pc and my mac to charge it but still no power
tried plugging it into my pc without the battery to see if the orange light comes on
Any Ideas??
I'm not exactly an expert but I'd have thought attempting to flashing a ROM shouldn't break its power supply. It doesn't add up. You mention the orange light, but does it actually come on or not?
I'll assume you flashed a USPL or you probably wouldn't be getting past 3% in the first place lol.
strange one
yea, it was all ready to be flashed, it was previously on a geniric htc rom that i put on it.
there is no orange light at all, no nothing, i cant seam to work it out, i mate has the same phone and im gonna try his charger and battery when i see him tomorrow but i still cant see how flashing it would affect the power, unless the device is blank now and it doesnt even know what the buttons do e.g the power button is not assigned to do anything.
try with another fully charged battery... and ELF/ELFin Golcard method, with a suitable flash file (like a Original one)
Just my 2 cents...
Try put the battery with the camera button pressed..
i have had the same problem
pres start button and fotos together
will appear 4 colors and ipl ..... and spl ........
if its appear: ipl 2....... and spl 1.11.000 you must upgrade your spl
read : http://forum.xda-developers.com/showthread.php?p=3038443&posted=1#post3038443
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
brick...
chipis said:
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
Click to expand...
Click to collapse
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Thank for answer me and understand what i ment
Ok what software you recoment?. I do not know if i have a unlocked phone but i do know that i used it with t-moble even that my pocket pc is for cingular, i went to those stores that unlocked phones and that it
Help.
I have a Wizard G4 and I tried to install a WM6.5 ROM (TechTeamup Mega Wizard rom) from the default WM5. I did not put in the hard-spl (as I now read) before I tried to flash. Now when it boots, I go strait to the flash screen (tri-color) screen. I tried ot run the hard-spl-G4 and it says it cannot find a device. I have tried to re-flash back to WM5 ROMs that I have found, however it says it cannont complete "ERROR 296: UPGRADE ONLY, which makes me belive I need a G4 Wizard ROM that is a full (not upgrade). What steps should I take now to revert back to a WM5 so I can re-try the "unlock" hard-spl proceedure to make the phone WM6 compatible?
Anyone have any suggestions?
IPL 2.28.0001
SPL 2.28.0001
Download the original ship ROM for your phone.
Turn the phone off.
Press and hold the Camera key, now insert the USB cable, Keep holding the camera key until you get the boot loader screen.
Now run the ROM update to flash back to WM5.
ricozy said:
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Click to expand...
Click to collapse
I brick my wizard too... What happened was I flashed my own cook of m6r5 it say successful but on reboot, it shows htc logo then stays ay tricolor screen:
IPL 2.26
SPL 2.26
Bootloader wont work..tried many times but I cannot connect to PC...
Tried ricozy post above, can access 3 color... but still cannot connect to PC...
Please help...anyone..
IF u can enter bootloader...connect to pc...u shud c "USB" written in the left bottom corner ...then flash a rom as usual