Database Users

VOIP - possible?

Is it possible to use the XDA2 as a speaker/microphone on your PC via bluetooth? I use MSN messenger on my PC to talk to friends over a headset, it would be great to talk to them over the XDA2 around the house and possibly at work instead of using a PC headset.

VOIP on XDA II
Could you let me know if you find a solution for this?
I'll be very interested as well...

Hi David,
I'm half way there. As far as getting voice to and from the phone via the PC, I installed NetiPhone (http://www.polypix.com/html/english/product_pda.htm) on the PDA and used NetMeeting on the PC. It works fine. Just input the IP shown on NetiPhone into NetMeeting and you'll get a ring on your PDA
The problem I've got now is getting friends to connect to my PDA over the internet. I mean, my PDA has an IP of 192.168.0.123 (via my Bluetooth hub on my PC) and my PC has an IP of whatever my ISP has given me. How would someone connect to my PDA from the internet? I've tried [email protected]<MY INTERNET ISP> and it doesn't work.

Hey David,
Any IP with the 192.168.1 range is the default IP for wireless devices worldwide , AP and routers.
You need the IP provided by your ISP ( preferably a static IP, call your ISP for a quote they are not that much more than a DHCP IP) to be able to reach it from an outside device.

ronin said:
Hey David,
Any IP with the 192.168.1 range is the default IP for wireless devices worldwide , AP and routers.
You need the IP provided by your ISP ( preferably a static IP, call your ISP for a quote they are not that much more than a DHCP IP) to be able to reach it from an outside device.
Click to expand...
Click to collapse
IP address 192.168.xxx.xxx is a NAT address. When you are behind NAT, you'll get a single way Audio or wont be able to connect. This is primerely because the VoIP software you're using works with H323.
Try using a software, which uses SIP (sesion Initiated Protocol), Then you might get better results.
Good luck.
As for me, I'm looking for a PDA H323 dialler, to dial out to a VoIP provider of my choice...
Regards,
David

Using Activesync v 3.7.1 to internet via cable router

Hi there,
Don't know if this is even possible I've read all the articles I could find here and tried Microsoft web pages. If you can help ill most appreciate it.
(Apologies if this has been answered please let me know the link...)
My internet connection (at home) is via NTL cable, My 4 pc's connect to the internet via a Linksys router, each PC has a private IP address along the 192.168.1.x subnet which NAT to the router for internet access - all transparent.
I do not have a proxy server at home, connection is established because each PC uses the router as a gateway for internet access.
My XDA2 refuses to talk to the internet via Activesync. I can confirm that my handheld connectiviy text bubble says that the internet connection is pointing to the PC connection. the paramaters in Active sync passthorugh are set to internet - But it just won't work.
I even tried configuring the proxy option to the routers address no avail.
The XDA wants to keep defaulting back to its GPRS connection.
At the moment I have disabled the phone completely to stop it dialing out whilst I am testing.
I'm out of ideas can anyone help !!!!!!!!

I managed to fix this problem. I set up a personal proxy server from
http://www.youngzsoft.net/ccproxy/ its an excellent proxy only 815k in size and its intelligent enough to understand NAT'd IP addresses etc for connections to routers.
All I had to do was to configure the XDA 2 work profile with the proxy server address then the internet passthrough worked fine.
For Bluetooth access (I use a D-link USB bluetooth adapter). I had a problem getting the XDA 2 to launch the bluetooth connection under the activesync. I used the excellent pocket bluetooth tools
http://216.239.39.104/translate_c?h...t+bluetooth+tools&hl=en&lr=&ie=UTF-8&oe=UTF-8,
after installing this the connection worked straight away with BT internet access as well.

even though i upgraded to the new O2 rom for the xda2, i still had problems until i resorted back to the bluetooth tools, so i have internet via bluetooth gondle to my adsl. But the internet speed on my xda2 is still damm slow, perhaps its limited by the bluetoot connection speed. (my adsl is a 1mb line plus a netgear wgt624 wireless router connecting my laptop to the internet. any idea how i could get a better speed?
also what i like to do is able to access all shared files on the network or on my actual laptop from my xda2. activesync lets me browse from the laptop, but i can use the xda2 to browse the laptops files. any idea how i could do that? the laptop itsself has a 802.11g connection and an assigned ip address, but i guess that has nothhing to do with the bluetooth connection. so has anyone got any suggestions how i could access the files? some detailes guidance would be extremely welcome. thanks.

Hi I am new to this forum, and like the person above am trying to find a way to browse files on my PC through my XDA2 (i-mate).
I am connected via bluetooth to my PC, activesync is working fine this way, as is internet browsing on my XDA2 using my PC's internet connection.
All I wan't to do is be able to sit away from my PC and get files from it to the XDA2 via bluetooth.
Apparently using Resco File Explorer and a wi-fi connection you can set up a network with your PC, but when I try this with Bluetooth it doesn't work - surely bluetooth can offer the same file sharing - just slower???
Please help us if you know a way!

Analyst said:
even though i upgraded to the new O2 rom for the xda2, i still had problems until i resorted back to the bluetooth tools, so i have internet via bluetooth gondle to my adsl. But the internet speed on my xda2 is still damm slow, perhaps its limited by the bluetoot connection speed. (my adsl is a 1mb line plus a netgear wgt624 wireless router connecting my laptop to the internet. any idea how i could get a better speed?
also what i like to do is able to access all shared files on the network or on my actual laptop from my xda2. activesync lets me browse from the laptop, but i can use the xda2 to browse the laptops files. any idea how i could do that? the laptop itsself has a 802.11g connection and an assigned ip address, but i guess that has nothhing to do with the bluetooth connection. so has anyone got any suggestions how i could access the files? some detailes guidance would be extremely welcome. thanks.
Click to expand...
Click to collapse
pls explain so more as am using Tiscali...
bR

Analyst said:
even though i upgraded to the new O2 rom for the xda2, i still had problems until i resorted back to the bluetooth tools, so i have internet via bluetooth gondle to my adsl. But the internet speed on my xda2 is still damm slow, perhaps its limited by the bluetoot connection speed. (my adsl is a 1mb line plus a netgear wgt624 wireless router connecting my laptop to the internet. any idea how i could get a better speed?
also what i like to do is able to access all shared files on the network or on my actual laptop from my xda2. activesync lets me browse from the laptop, but i can use the xda2 to browse the laptops files. any idea how i could do that? the laptop itsself has a 802.11g connection and an assigned ip address, but i guess that has nothhing to do with the bluetooth connection. so has anyone got any suggestions how i could access the files? some detailes guidance would be extremely welcome. thanks.
Click to expand...
Click to collapse
pls explain so more as am using Tiscali...
bR

essojay said:
Analyst said:
even though i upgraded to the new O2 rom for the xda2, i still had problems until i resorted back to the bluetooth tools, so i have internet via bluetooth gondle to my adsl. But the internet speed on my xda2 is still damm slow, perhaps its limited by the bluetoot connection speed. (my adsl is a 1mb line plus a netgear wgt624 wireless router connecting my laptop to the internet. any idea how i could get a better speed?
also what i like to do is able to access all shared files on the network or on my actual laptop from my xda2. activesync lets me browse from the laptop, but i can use the xda2 to browse the laptops files. any idea how i could do that? the laptop itsself has a 802.11g connection and an assigned ip address, but i guess that has nothhing to do with the bluetooth connection. so has anyone got any suggestions how i could access the files? some detailes guidance would be extremely welcome. thanks.
Click to expand...
Click to collapse
pls explain so more as am using Tiscali...
bR
Click to expand...
Click to collapse
sorted!!!
BR

internet access through ad hoc wifi connection?

hi, im not able to connect to the net with my wizard.
i dont have a wireless router so am connecting directly to my laptop, the ad hoc connection i have made works fine for file tranfers, but not for activesync or connecting to the web in either PIE or minimo.
i know activesync isnt possible but surely i should be able to use the broaband from my laptop?
any pointers would be greatly appreciated. software? settings?
its a t-mobile uk vario with qtek test rom.
also anyone know of a remote control utility, i use logmein but would like something a little more menu/macro based for control of media.
cheers
kevo

Try turning on Internet Connection Sharing (ICS) on your laptop; that'll make your laptop act a bit more like a router, providing NAT services to the Wizard.

yeah i've tried that, and i've just tried bridging connections (dont really know much about that) but that hasnt worked either.
kevo

My configuration
Me too, I use ADHOC connection for my WLAN.
PC configuration:
ADSL connection shared
Adress IP:192.168.1.1 Mask:255.255.255.0
PocketPC configuration:
Adress IP:192.168.1.55 Mask:255.255.255.0 Gateway:192.168.1.1
DNS:80.10.246.2 for Wanadoo
Your problem is certainly the DNS.
You can put 192.168.1.1 too.

so it is possible? cool!.......but im still having problems.
i cant figure out how to enter these settings, not to sure where to put them,
iv tried puttin the DNS in the -> connections -> vpn
and -> network cards -> networks adapters -> SDIO WLAN Wireless Adapter
sorry to be a pain, but could you point me to where to get each address and where to put them?
also is there anything particular you did to set up the adhoc network? i just used the Windows XP wizard and then ticket the AdHoc option after.
my laptop is conected to the router and the router is connected to aol adsl.
the ip address of my laptop is showing as a simple 10.0.0. number on the LAN but "Autoconfiguration IP Address. . . : 169.254.235.147" for the WLAN
none of my setup has a static ip address, could this be causing the problems?
thanks
kevo

It's more hazardous without static adress but it's can work.
My PC has directly access to the Internet with a ADSL modem.
It's here (network cards -> networks adapters -> SDIO WLAN Wireless Adapter )
Apparently, it's ok for your PC and the Ad-Hoc mode.
Maybe, you should have your adress IP WLAN on the same network adress of your router.

I GOT IT WORKING!!!
I started again from scratch.
set a new WLAN. added new setup to the vario, added the DNS etc to the vario.
the problem i was having was the way i was sharing the internet connection, i was trying to shared the internet from the wireless to the lan rather than the internet from the lan to the wireless (if that makes sense to anyone!!!). i also ticked all the connection sharing services to allow them, just need to go through them and see which i dont need now.
thanks for the help guys
kevo
(its showing my transfer rate as 11Mbps, although i think iv done the G tweak and my laptop says its got a G card. what speeds should i be getting?)

IPSec VPN Failing to connect over new internet sharing

Hello,
Well I hope I'm putting this post in the right place, if not please move it. I have a 8525 with cingular. I need vpn access for my office connection from my laptop. We use a Fortiwifi 60 with the Forticlient software for VPN access. I used it with the old wireless modem settings on my 8525 and it worked with both wap. and isp. I recently upgraded to the new offical rom and used it fine (without trying the VPN access) for a few weeks. I went on my first trip last week and could not connect to the vpn. It would verify PSK and X-AUTH but fails to pull an ip address. I tried it with a static ip and it failed as well. When I check my connection monitor it shows no data coming back from my vpn gateway. I tried it on the hotel's internet and it works fine. I also tried another wifi signal and it worked as well. I changed the media net settings to go through isp instead of wap but that didn't help. Does anyone else have this problem with there VPN settings? I wonder if it is the new type of connection sharing or a change to the Cingualr network? Any help would be appreciated.
Thanks.

dechutes said:
Hello,
Well I hope I'm putting this post in the right place, if not please move it. I have a 8525 with cingular. I need vpn access for my office connection from my laptop. We use a Fortiwifi 60 with the Forticlient software for VPN access. I used it with the old wireless modem settings on my 8525 and it worked with both wap. and isp. I recently upgraded to the new offical rom and used it fine (without trying the VPN access) for a few weeks. I went on my first trip last week and could not connect to the vpn. It would verify PSK and X-AUTH but fails to pull an ip address. I tried it with a static ip and it failed as well. When I check my connection monitor it shows no data coming back from my vpn gateway. I tried it on the hotel's internet and it works fine. I also tried another wifi signal and it worked as well. I changed the media net settings to go through isp instead of wap but that didn't help. Does anyone else have this problem with there VPN settings? I wonder if it is the new type of connection sharing or a change to the Cingualr network? Any help would be appreciated.
Thanks.
Click to expand...
Click to collapse
I had the same problem with another IPsec client with this ROM. For some reason I could not get Internet Connection sharing to work when connected via USB. Bluetooth pan worked. The VPN client was not binding to the ICS/usb adapter. I have since upgraded to WM6...Sleuths ROM...and USB/ICS now works.

Well I tried the phone on another computer and the vpn works just fine. I guess it's something on that computer. Anyone have any ideas? I'm going to try reinstalling the virtual adapter in hopes that it is a binding issue (thanks to tco for that). I'll let you know if I figure it out.

ICS & VPN with WM6

My searches on the web haven't yielded much help or information so I thought I would come to the experts...
I have a Treo 750 that I just "upgraded" to WM6 2 days ago. I noticed that DUN has gone away and was replaced by ICS. After configuring my laptop to use that instead of DUN I connected and was surfing the web. My problem now is VPN. I travel frequently (luckily I'm in the office until Jan.) and regularly used my phone to connect to the corporate network via VPN. I also work with a lot of other companies and have VPN access to their systems as well. Basically now I can open my Cisco VPN client, connect to a VPN gateway, authenticate, get assigned all the appropriate IP information, but cannot communicate on the network. What gives? Is there a solution to this? If not, what the heck was MS thinking when they did this!? My phone is basically useless for one of the major reasons I bought it...
Any help is appreciated!
thanks!

Ok, further searches found that DUN can be added back into WM6 via a cab that was posted here at the XDA forums. I installed it and the DUN service is now visible again. I unpaired by phone and laptop, re-paired, and included DUN. Now when I try to connect, I get the DUN connection box after the bluetooth connection is initiated but when I click DIAL I get the DIALING... prompt, followed by Error 678: The remote computer did not respond.
Anybody get this working on a Treo 750? Thoughts, ideas suggestions?

What is the ip address you are getting via the cisco vpn client
It maybe that it is in the same subnet as the ip address assigned to the pc from the wm6 ics. The ICS gives the address 192.168.0.1. and if your Cisco is also giving a 192.168 address then you will have two routes for the 192 address range thus giving you the problem when accessing hosts.
If this is the problem Im pretty sure you can change the address allocated via the ICS using a registry editor. If not you may be able to get work to use a different range for you on the cisco vpn.

Our corporate network is 172.x.x.x so it's nowhere near the 192.168.0.x assigned by the phone. When I look at the route in the VPN client I see 192.0.0.0, 10.0.0.0, and 172.0.0.0 so I am assuming 192 is my laptop, 10 is the phone, and 172 is the corporate network.
I'm guessing NATing is the problem. I've been reading that if I use a different APN (isp.cingular instead of wap.cingular) there is no NATing. I've tried both, and I've tried turning off and on the "force AT&T" proxy setting to no avail.
Tried the DUN cab hack that is floating around for WM6 also. The service is active again and I can also add Modem Link back in and my laptop sees my Treo as a modem but when I dial I get an error stating the remote computer did not respond. I'm guessing along with going from WM5 to WM6 AT&T also updated the radio so the old communications protocols don't work anymore?

Hello Sir,
I have exactly the same problem... I have successfully connected via VPN, however unable to communicate with any devices on that network... Then what is the use of VPN on the phone? I've tried searching online for answers, but no luck... People are having the same problem but no one knows how to solve it... I'll try and trouble shoot this problem more as soon as my exams are done...

Hi
Working successfully for me. I am using Imate jasjam wm6. Pc using cisco client connecting via ics on phone. I have telstra 3g connection tested ok on both telstra.internet (Nated ip) and telstra.extranet (real ip).
You are correct it may be an nat issue. Can you check that your transparent tunnelling is on as follows: right click on your connection entry in cisco client and select modify then transport tab. Check that enable transport tunneling is enabled ipsec over udp(Nat/pat).
The other thing to check is that the cisco vpn server aslo has transport over Nat on as well.
Also are you sure your corporate ip range is 172 or is that the range given by the cisco vpn to clients.

Transport tunneling is on (always was). I'll have to check with our network admin and check on the VPN server setting...I guess as long as I have connectivity back to the office, I don't need it that badly for all the customers I need to connect to at various times.
Yep, positive on the corporate IP. Right now it is 172.28.1.87 and I'm in the office.
Thanks for the help so far. Got any other suggestions on how I can troubleshoot further?

One other thought...should I modify the registry on the phone to assign a different IP address to my laptop? Would that help?

Same Problem
MX. I am having the exact same issue but with Securemote VPN. I've looked through the registry and found the assigned address, but I'm wary of changing anything until I can find some more information.
Anyone out there ever change the DHCP configuration for their phone?

Somewhat related question?
Im attempting to route my connection on my mobile through a laptop acting as a wan bridge, then uplinking it into the router. The issue Im having is that XP and WM6 both use the same IP Block. Ive read and read and cant find much to tell me how to change the WM6 IP BLock to something like 192.168.2.1 rather than the default 192.168.0.1
Does anyone have any pointers? Ive looked through the registry. There MUST be a simple way to change a default.
To clarify my setup, I am using ICS Via USB into a UMPC laptop running XP. The UMPC is set to share that same connection back out over Ethernet. The ethernet runs into my WAN Uplink on the router and then back out via wifi/rj-45
This setup works as I have done it using Wifi with other networks, and I can chose the "Lan3" to share under the advanced settings on the UMPC. The reason I dont just share out via Wifi from the start is that Wifi on my Kaiser and Raphael both make the device to hot to charge, thusly killing the battery within a couple hrs of sharing. If I share via USB , it stays pretty cool and still charges.
Anyone have any pointers?
I have already tried tricking XP into using the Lan on another block but as soon as you try to share the USB lan, it reverts back to the 192.168.0.1
The only way I can imagine is a registry modification or a program change in ICS.
Thanks Much!