hi guys.....i`m a new member in this forum.
right now, i have problem with my xda exec and need your help badly.
the problem starts with phone gets slower and it seems needed to be "soft reset" as always with the pocket pc.after i did the soft reset, the phone wont turn on.because of it, i try to perform hard reset on my phone, after i pushed 0 to restore factory default, the only message i got is "clearing now" for about 1 sec and after that the exec turn off again. i try this hard reset for several time and the result is still the same.
i also read in this forum how to get into the "boot loader mode" but there is nothing happened with my phone after i perform the 3 button push.
so, PLSSSSS let me know if any of you could solve my problem with my exec.......
btw, i already try to connect my exec with my pc and the message i get is unknown usb device
Andi, please don't cross post, and please use a helpful topic title.
Forum rules state this.. please read.
V
Related
hi every friend,
please help me, i was update my xda to ppc2003 while computer was down, that cause me have to restart it, after that my xda dead, i use hadr reset it says gsm ok, then start a set of test like,ram, usb, sound,sd card. then stoped. can someone tell me how to fix it. thanks a lot, i really need that pda.
hard reset doesn't lead to these diagnosis ... are you sure you didn't go into the boot loader mode ??
only hard reset will cause nothing, i use hard reset and power key come out the bootloader svreen says" gsm ok" then i press action key, it start test
this means "soft reset" ... the hard reset is the small hole with red battery icon.
Anyway, having "GSM Ok" is a good news ... all you need now is to try HARD reset ... and if it doesn't work, you may flash your ROM with a new one using SD card if your boot loader version is older than 6.22
hi guys.....i`m a new member in this forum.
right now, i have problem with my xda exec and need your help badly.
the problem starts with phone gets slower and it seems needed to be "soft reset" as always with the pocket pc.after i did the soft reset, the phone wont turn on.because of it, i try to perform hard reset on my phone, after i pushed 0 to restore factory default, the only message i got is "clearing now" for about 1 sec and after that the exec turn off again. i try this hard reset for several time and the result is still the same.
i also read in this forum how to get into the "boot loader mode" but there is nothing happened with my phone after i perform the 3 button push.
so, PLSSSSS let me know if any of you could solve my problem with my exec.......
btw, i already try to connect my exec with my pc and the message i get is unknown usb device
sorry for u guys who`s already open my thread and thank u so much for trying to help me.i already solve my problem after i read in one of the threads from this forum. thank u so much to this forum, its the greatest mobilephone forum ever .......its true....
After (I think) successfully upgrading to WM6, I've had a few problems...
1) I can't seem to soft reset anymore (holding down Power at the top + the reset button)...it seems the only way I can now reset my unit is by physically removing the battery...
2) I can't access the bootloader SERIAL mode...I can access the options for the kernel hive and formatting storage, but no success being able to get into USB mode to reflash my unit
Any help or suggestions would be greatly appreciated - I only bought this phone on Friday
1. This was hard reset in WM2003 - for soft reset just press the reset button
2. You need to press and hold power+reset+record(WMP) buttons at the same time
I suggest you read WIKI first before asking questions which are answered a million times
Thank you for the prompt reply.
I can understand your frustration with many people constantly asking these questions, but please don't make me feel like an idiot when I've actually read the Wiki and tried Googling the problem prior to posting.
To clarify, I know *how* to access the SERIAL option (I had to do it to upgrade from 2003 to WM6 to begin with). My point is that holding Reset+Power+Record doesn't work anymore. It just continues the boot process and goes straight to the Windows Mobile splash screen. The reset button, in and of itself, does nothing at all. I've tried everything from just tapping it a few times to pressing and holding it for upwards of 30 seconds...but it doesn't seem to do anything for me.
Try to hold and press power+record+cam buttons then press reset while holding those buttons.
Yeah, it does nothing...I have a feeling that the actual reset button is no longer working on the unit...not sure if that's to do with the upgrade to WM6, or if it's a hardware problem and just happens to be coincidence :-/
don't take xplode's advise wrongly. it's just that reading AND understanding the WIKI is important especially for beginners like yourself.
if you think you've successfully upgraded to WM6, it's probably because of the "Congratulations" message that was displayed... well, you're almost there, though not quite.
try to fully understand the no/yes/yes instruction in the WIKI... the reset+power+record combination is NOT what you should be doing. it has been replaced by another... here's the thread that could guide you... http://forum.xda-developers.com/showthread.php?t=327978&highlight=kitl
and here's the pertinent wiki page...
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4
good luck and welcome to the BA community.
Anyway if this that you try to explain is that the hardware buttons no longer work, you can try the MTTY method, if you have read the wiki you already know what exactly to do
Thanks raymonds, I will try not to, but I just don't want people thinking I'm yet another new member that doesn't read anything before posting, because I know how much I hate that too...I tried reading up on my problems for 4 hours last night before deciding to post because I couldn't find anything else to help.
I have successfully upgraded to WM6 and went through the no/yes/yes steps - the issue is that I want to go back to WM2003 or WM5...they seemed far less problematic for my phone for some reason..one problem I'm facing now is that my BA, pure and simple, no longer recognizes that I have a cellular carrier at all, making it essentially useless as a phone. When I try to go into SIM Manager, it hangs for a while, then goes into the screen saying that only emergency calls can be made...but when I try to put in my PIN, it says "Unknown SIM error", though the SIM works fine in my other phone...
I'm trying to use the Power/Reset/Record to either try reflashing in the hopes that'll resolve my issues, or downgrade...either way, it's not allowing me to do so, and I obviously can't do this while the phone is booted into WM6. It just seems like the reset button is no longer working, since neither combination that uses it (Power+Reset or Power+Camera+Reset) works anymore.
try to downgrade with MAUpgradeUT_NOID.exe, and then reupgrade, another thing you can do is to reflash the radio rom. The MTTY method resets bootloader settings which may be the solution to your problem.
MTTY under Windows XP is explained HERE
xplode, mtty requires one to do the power+reset+record combination, which he currently cannot do.
is this a second-hand unit?
Hm, there was another way to put your device into bootloader mode but i have never tryed it, in most of the WM2003 upgrades there was EnterBL.exe, and when you copy it to the device and execute it the device goes to bootloader mode...
but it also creates problems - read here
Also i had problems in the past with the latest version of MTTY (1.45) and used previous one 1.01 which worked like a charm
Sweet - thanks xplode and raymonds for your time.
Unfortunately I can't try these as I am at work right now, but I do appreciate the suggestions and will try them as soon as I get home.
If I can't get it to work, oh well - off to the service depot and a (probably) expensive lesson learned.
Please keep us updated, about your issue
Thanks guys...
So, I'm taking it that the radio stack is now corrupt, since it's no longer even showing a version number on my BA. I tried the methods xplode suggested - when I enter the unit into KITL mode, I take it I'm supposed to use USB Active as the transport method, since MTTY won't recognize a device otherwise, and my phone just boots into Windows from that point.
When I try to run MTTY though, all it does is display "kITLª" over and over again...I'm not sure if that's normal, or even how to enter a prompt of some kind...
I'm starting to wonder if maybe I should just take it to the depot, pay the $75 I was quoted, and learn my lesson... :-/
Any other suggestions, or am I just totally doing what you suggested wrong?
You do not need to enter KITL because this is used to debug your WM build using Platform builder
Just try to put your device to botloader mode and then use MTTY to instruct the bootloader what to do, or just reflash radio and then new rom
Hi everyone,
I recently received an XDA Orbit 2, literally, charged it for 2 hours, and when it was full charged, I started using it, I had it for about 2 months now, and recently I changed my home Internet connection to wireless (It's a B & G connection) so my laptop connects fine, and when I tried to connect my XDA Orbit 2, it connected and then soft-reset itself, and now it just loads the O2 screen, then Windows Mobile screen with the volume controller and I can't do anything else so here's what I have tried so far:
- Soft reset
- Removed battery and SIM
- Since I can't access phone's menu at all, I tried to Hard Reset method by holding the 2 soft key, reset, and the power button - So I get the warning that everything will be lost and to press 'Send' to continue, so I press the green key, and soft resets and goes back to the same situation again.
- The latest thing I tried is to load the Hard-SPL into the SDCard which has been formatted to FAT32, so loaded the POLAIMG.nbh into the root. and loaded the phone into BootLoader mode (Camera and reset buttons). It loads the memory card and just says 'Loading ... ' I left it for about an hour, until the battery died completely (I'm sure it's not supposed to take that long). And still the same problem.
I'm not sure if this phone is now bricked, can anyone help me plesae. I really need this to start working again, I don't have any info. on it. (Everything was sync. previously).
Kind regards,
Since you havent really messed with SPL, i would say to take it back, since its still into warranty.
Thanks for the reply, I'm not actually in the UK and will be overseas for a while. I don't really mind experimenting so I would appreciate any advise on this matter. Thanks again.
htctytnowner said:
Thanks for the reply, I'm not actually in the UK and will be overseas for a while. I don't really mind experimenting so I would appreciate any advise on this matter. Thanks again.
Click to expand...
Click to collapse
I assume just boots into bootloader and then stays there?
If yes you culd try searching out a thread on MTTY and recovery from boot loader but I dont know how well that would work on polaris as I have not tried it yet.
HTH
Leon
Thanks for the reply, I heard about the MTTY process, but I've no clue on how to do it, since the phone can't connect in ActiveSync mode. Is there a thread or WiKi guide out there?
htctytnowner said:
Thanks for the reply, I heard about the MTTY process, but I've no clue on how to do it, since the phone can't connect in ActiveSync mode. Is there a thread or WiKi guide out there?
Click to expand...
Click to collapse
Only in the ELF forum
Here:
I'm pretty sure you can download MTTY from here and read through how to use it.
http://forum.xda-developers.com/showthread.php?t=347700
Also it is worth checking the wiki and searching
http://forum.xda-developers.com/showpost.php?p=2054848&postcount=38
Please do some research! I have not done this before and I have no idea what the commands do!!!
pqillu said:
You can try this:
Originally Posted by christonge
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
THX to christonge
Good luck.
PQillu
Click to expand...
Click to collapse
Please Heeelp!
I wa installing a rom from todopdas.es an my Polaris doesn´t pass from the screen where´s said "smart mobility", and R1.58.21.23 G 25.65.30.04H D 1.52.00.00, please what I can do?
You need to do Hard Reset, all information will be wiped off. To do hard reset, hold down the:
1.Press and hold the GPS/MESSAGING and INTERNET EXPLORER
buttons, and at the same time, use the stylus to press the RESET
button at the bottom of your device.
2. Release the RESET button, but
continue pressing the GPS/
MESSAGING and INTERNET
EXPLORER buttons until you
see this message on the
screen:
This operation will delete
all your personal data,
and reset all settings
to manufacturer default.
Press Send to restore
manufacturer default, or
press other keys to cancel.
3. Release the buttons, and then press SEND on your device to perform
the hard reset, or press any other button to cancel the reset.
Good luck.
Hi,
I'm using an HTC TC POLARIS100. Today I upgraded my ROM and SPL successfuly. If you're still in trouble and believe the same process will help, I will let you know the process followed.
GUY
Hi!
I`m totally new to this so i would like to ask for a help! I have Qtek s110, and i was reading about updating the ROM and that kind of things, trying to get know better the device.
On http://wiki.xda-developers.com/index.php?pagename=BackupExistingRom
i have read that if you press Camera + Power and Soft Reset, you will enter into the bootloader mode. I wanted to see that mode, and pressed that. I got some message - word and some number and nothing happend (not error message but i cannot remember exactly the word and the nubmer..like some version number).
Then i have restarted the device so i could use it again and when the device finished the boot, i had to calibrate the screen, and things like that, like on the first boot of device (the programs where installing). After that i lost all of my personal informations, contacts, programs!!! PLEASE HELP if there is any help!
Of course, i didnt make any ROM backups! Is there any way to get my data back!? On my storage card i saw some folders that i didnt make myself. Some WMDRM with some .hds file and some 08071200001 empty folder!
Please help!
P.S. Why the hack that guy didnt said that button sequence is hard reset of the device!?? DAMN!
Sorry, but i`m really pissed! I will kill somebody now!
eyej said:
Hi!
I`m totally new to this so i would like to ask for a help! I have Qtek s110, and i was reading about updating the ROM and that kind of things, trying to get know better the device.
On http://wiki.xda-developers.com/index.php?pagename=BackupExistingRom
i have read that if you press Camera + Power and Soft Reset, you will enter into the bootloader mode. I wanted to see that mode, and pressed that. I got some message - word and some number and nothing happend (not error message but i cannot remember exactly the word and the nubmer..like some version number).
Then i have restarted the device so i could use it again and when the device finished the boot, i had to calibrate the screen, and things like that, like on the first boot of device (the programs where installing). After that i lost all of my personal informations, contacts, programs!!! PLEASE HELP if there is any help!
Of course, i didnt make any ROM backups! Is there any way to get my data back!? On my storage card i saw some folders that i didnt make myself. Some WMDRM with some .hds file and some 08071200001 empty folder!
Please help!
P.S. Why the hack that guy didnt said that button sequence is hard reset of the device!?? DAMN!
Sorry, but i`m really pissed! I will kill somebody now!
Click to expand...
Click to collapse
Hi there
There are no way to restore the data from ram since you hard reset your device. The big lost is contact book and sms message. You can try to copy the contact from sim to phone if it is exist in Sim card.
Good luck
try removing the battery n keep it like that for about 10 hrs.. n then put it back on n start the ppc..see if it helps
..n if it doesn't do not worry, ur fone aint dead yet....u'd have to go thru the hard way then