Related
I was updating my new i-mate SP3 (typhoon) to the latest i-mate ROM 2.4.33.11 which completed successfully but now every time I turn on the phone it goes directly to the bootloader tri-color screen. I tried several times to update the ROM again but it does'nt help. It shows the proccess completed successfully but the phone is still stuck in bootloader mode.
In the bootloader screen it shows the following
IPL 1.00
SPL 2.5.0102
I even tried to flash the ROM through an image of Orange4114_ALL_SPL1010091 on a miniSD card but it gives an error message
"Not allowed update!"
Please help me figure out how to get my phone working again.
Same PROBLEM here HELP..!
Exactly the same problem if anybody can help ..please do.
spl
hi
same problem my sp3
SPL
Same problem on spv c500 stuck in bootloader but with 2.05.0130 SPL
sp3i stuck
Hi all,
I have the same problem, but I didn't try the mini-sd boot.
surfturtle, will you kindly send me the way?
Thanks
Hi guys...
I don't have the Typhoon and don't know if this will work for you, but this is at least how we fix this problem on the Hermes:
Enter into bootloader using mtty.exe and run the command "set 14 0" and "task 8". Phone will reboot and start OS.
If it doesn't work, then try the SD flash method mentioned by surfturtle. Keep in mind that if your device is not superCID the image file should match the CID of your phone (must be an original shipped update from your vendor). This method consist on:
1) extract the rom image from the rom upgrade exe (winrar or cabextract can be used for that) and you'll find a .nbf file.
2) Rename it to TYPHIMG.nbf
3) Format your SD card in FAT32
4) Put TYPHIMG.nbf on the root folder of your SD card
5) put sd card on the phone, and enter into bootloader
6) confirm flashing on screen, and wait until the process is finished (do not reset it, will take about 30min).
Check the hermes wiki if you need more information on any of this.
Good luck!
sp3i stuck
thanks pof,
but where would I get mtty.exe and where will I see "set 14 0" & "task 8"
thanks again.
Re: sp3i stuck
@Tall_Man: See the hermes wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
I-mate ROM
Hi, I did the upgrade through the PC but the device info still shows the old ROM: 2.1.33.13 No error messages and the phone keeps hanging on me.
Is this version of ROM the Arabic one? If not, can someone post or point to where I can download the arabic version? I did not find it on the I-mate website.
Thanks in advance,
I-mate SP3 (?rom 2.1.33.13)
Artemis and PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap
i tried to upgrade my o2 arte200,i waited 30min. but installation frozen.
i did reset but after reset my phone stucked at bootscreen
IPL : 1.25.0001
SPL: 1.25.0000
GSM : 02.67.90
OS : 1.28.0.0
Please help... i tried hard reset and soft reset ... but no way...
when i plug usb cable activeSync dont recognise phone
same problem here,
help needed in advance
Active sync is usable only with Windows booted device. If Windows isn't able to boot, you must enter into bootloader, plug usb cable and then start rom flashing.
hi sir
i entered bootloader screen,connected usb cable ... (i can connect using mtty)
i run the software "CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE"
but gets an error message " cant connect to the phone"
WHY ???
finally i did connection ...
but goes %3 and gives error message
ERROR 294 INVALID VENDER ID
this update utility cannot be used for your PDA Phone.Please check your update utility ??????
CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE
is a Rom for the Wizard not for the Artemis.
You need the original ROM so you have to search for the O2 ARTE200 ROM. The language of the ROM has to be correct as well.
how do you get the phone into the bootloader?
Tha said:
how do you get the phone into the bootloader?
Click to expand...
Click to collapse
Press and hold the record button and then do a reset.
no it doesn't work
My DOPOD was in the same trouble. I got the same vender ID error. Does anyone know where to get the original DOPOD P800 chinese ROM?
The same problem has I also.
My ROM upgrade ended bad. Test of installing of different ( I have already them probably 12) the INVALID ends VENDOR ID
I it can not now to remove CID nor to find out what it has it CID HTC__001 does not it fit. T - MOB 005 does not it fit.
I look for original romu from Dngaard ( DK)
Someone knows what CID maybe it is in HTC 3300. I have HTC P3300 is distributed would to Dangaard.
Where from him download
I greet
Irek ( POLAND)
im having the same problem on the o2 orbit ( need a orignal rom
upgrading
hai i am stuck in o2 orbit flashing in bootloader mode
help needed urgent
i got it working after i found the original german rom...loaded the orbit into the bootloader screen with 3 colors....plugged in the usb cable..then ran the german rom, after a few mins it reset and the orbit loaded up...after that i followed these steps to get it into english
http://forum.xda-developers.com/showthread.php?t=290241
flashed it with the tmobileuk 1.13 shipped file. everything is ok now.
cbprod said:
i got it working after i found the original german rom....
Click to expand...
Click to collapse
Where do you find the orginal rom?
Please help us!
send me a pm with your email, i'll send it to you
got mine back from the repair center friday.
no cost at all, fixed
route said:
finally i did connection ...
but goes %3 and gives error message
ERROR 294 INVALID VENDER ID
this update utility cannot be used for your PDA Phone.Please check your update utility ??????
Click to expand...
Click to collapse
could you tell me how did you manage to conect your phone? i have the same problem and i can't get my palm recognized by windows...
you must go into the bootloader.
i´ve found the orginal o2 rom and now it´s working fine with wm5.
i wait for the o2 official wm6 update (i read something about may).
xister said:
you must go into the bootloader.
i´ve found the orginal o2 rom and now it´s working fine with wm5.
i wait for the o2 official wm6 update (i read something about may).
Click to expand...
Click to collapse
is that the o2 UK rom or the German one
Hello!
I have strange problem with my Wizard. 4 month ago i was trying to install Pathfinder 1.2, but when I installing this ROM using ShellTool my PDA bricked. Now all the time it's frozen on Splashscreen with IPL/SPL GSM and OS information. All HR completed without any errors and all ROM's upgrading finish correctly.
Once time, after 2 months for breaking, my Wizard just started and working very well, I do 2 HR and few SR and my Wizard still working good, but when I shut it down and pull out battery my Wizard again frozen and until now can't wake up. I have CID Unlocked by imei-check. I tried to install many different ROM's, e.g. Wizard Love, Dopod (CHS), T-Mobile, Orange (PL) but nothing work. I also tried way with SD Card but my ROM's doesn't work, I think I need some working dumped ROM. I was searching help on few forum but poeple on polish forums don't know how to help me. May someone here have idea where can i find working dumped ROM or have any other idea how can i fix my Wizard?
Thanks for any help
alldoe
PS Sorry for my english
which is your device,post full data of your phone,IPL/SPL...? Make...?
As you say you installed through Shelltool,is it a G4 DOC chip version ?
You say it's stuck at the splash screen with ipl/spl and gsm version,which splash screen,is it OS (Rom) initial splash screen or a Bootloaders (Multicolored) screen ?
Secondly ,try to get it into bootloaders (multicolor) screen,if it gets into bootloaders,connect it to PC via usb cable,check small usb appears at the bottom of the bootloader mode in the phone,if it does,than flash a carrier's official Rom to recover back to it's default status.
Good luck
Try the Button's ROM (which is in Wizard Upgrading subforum). Then unlock it again (It may be causd by a fake CID unlock when you try to unlock when IPL/SPL is 2.xx)
My current
IPL/SPL 2.24
GSM 02.25.11
OS 2.24.10.1
I have G3, but I was using ShellToll because I can't install by RUU file.
My Wizard stuck at ROM Splashscreen, i can get into bootloader screen, but when I flash any ROM, everything upgrading well but after Reboot it still frozzing at Splashscreen. I was tried Button ROM sometimes but it doesn't work, I have CID unlocked by Imei-check.uk and everything is okay, I can install ROM from G3 and G4 chips. And ... I remember, that before CID Unlocking my IPL and SPL have different value.
PS. I was unlocking my CID, after my Wizard bricked.
alldoe said:
My current
IPL/SPL 2.24
GSM 02.25.11
OS 2.24.10.1
I have G3, but I was using ShellToll because I can't install by RUU file.
My Wizard stuck at ROM Splashscreen, i can get into bootloader screen, but when I flash any ROM, everything upgrading well but after Reboot it still frozzing at Splashscreen. I was tried Button ROM sometimes but it doesn't work, I have CID unlocked by Imei-check.uk and everything is okay, I can install ROM from G3 and G4 chips. And ... I remember, that before CID Unlocking my IPL and SPL have different value.
PS. I was unlocking my CID, after my Wizard bricked.
Click to expand...
Click to collapse
You can download this rom CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe on XDA,it contains IPL/SPL 1.01,and upgrad this rom,then you'll find your IPL downgrad to 1.01,and SPL still is 2.24,and then,use aWizard tu unlock your CID,after this,your CID should be unlocked,you can use RUU upgrad any rom you want.
I just do this yesterday,my CID isunlocked now.And RUU now works on my device.
luoluomeng said:
You can download this rom CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe on XDA,it contains IPL/SPL 1.01,and upgrad this rom,then you'll find your IPL downgrad to 1.01,and SPL still is 2.24,and then,use aWizard tu unlock your CID,after this,your CID should be unlocked,you can use RUU upgrad any rom you want.
I just do this yesterday,my CID isunlocked now.And RUU now works on my device.
Click to expand...
Click to collapse
Hello! I have CID unlocked. When I install Button ROM my IPL and SPL is the same (1.01). Every RUU works but It still frozen. 2 Days ago i found on other forum this advice:
INSTRUCTION :
1. miniSD - formated in PC - FAT format (now FAT32 !)
2. Wizard On and Bootloader (press reset and keep photo button let go reset) 3 color display. Put in card to Wizard.
3. Connect USB - PCC to PC
4. Launch MTTY 1.42 (my ver.) with USB connection
5. Write command - r2sd os end press enter
6. Program it will record OS on miniSD
7. After recording make Hard Reset or turn on Bootloader
8. On Display should be written - Format partition ?? (5 sec.) - to confirm press Voice dial button. If inscription it will disappear repeat point 7.
9. If Format partition successful wait OS is write. Done.
10. Draw out miniSD
11. Make Hard Reset
12. Enter in bootloader
13. FOR NON CID WIZARD - Flashing Wizard RUU (must be proper version) - ERROR 300 is bad RUU ERROR 266 turn off Wizard and turn on connect to PC
14. With CID (for example CID G4) seek forum for flashing Wizard with CID G4
My Wizard it lives
Click to expand...
Click to collapse
I was carry out all command step by step, and after flashing proper version Orange ROM my Wizard woken up, but today my Wizard get stuck again and now this way don't work, and I have to find a new method to rescue my PDA.
My Wizard woke up! I find ERA PL ROM (RUU_Prodigy_3829_382130_027111_TMO_PL_PLK_Ship) which flash excellent and working, but now I have a new problem. I can install other ROM after that but none of them work, every stucked at Splashscreen like before.I need to find some WM6 ROM which will working? Someone have some suggestion?
alldoe said:
Hello!
I have strange problem with my Wizard. 4 month ago i was trying to install Pathfinder 1.2, but when I installing this ROM using ShellTool my PDA bricked. Now all the time it's frozen on Splashscreen with IPL/SPL GSM and OS information. All HR completed without any errors and all ROM's upgrading finish correctly.
Once time, after 2 months for breaking, my Wizard just started and working very well, I do 2 HR and few SR and my Wizard still working good, but when I shut it down and pull out battery my Wizard again frozen and until now can't wake up. I have CID Unlocked by imei-check. I tried to install many different ROM's, e.g. Wizard Love, Dopod (CHS), T-Mobile, Orange (PL) but nothing work. I also tried way with SD Card but my ROM's doesn't work, I think I need some working dumped ROM. I was searching help on few forum but poeple on polish forums don't know how to help me. May someone here have idea where can i find working dumped ROM or have any other idea how can i fix my Wizard?
Thanks for any help
alldoe
PS Sorry for my english
Click to expand...
Click to collapse
i have the same proplem but i have a g4 wizard and it's not cidlocked tell me plz what to do plzzzzzzzzzzzz :'(
Hello Buds,
I've upgrade my p 3300 a few weeks ago with Artemis_touch_1.0_WWE_rapid
IPL 1.14.0001
SPL 1.14.000
GSM 02.67.90
OS 3.7.0.0
After some days a freeze and soft reset, I made a hard reset, and re-use the upgrade soft ware.
Now its completly block on the boot page with HTC.
I use RUU(in( Artemis_touch_1.0_WWE_rapid) in the Bootloader but it run but after 3% : error 270
If a use a newer RUU ( Release_Aje_fr_1.90Full_YuanYuan) : error 260
please help me I completly lost !
Trux 13
HTC P3300IPL 1.14.0001
SPL 1.14.000
GSM 02.67.90
OS 3.7.0.0
I had almost the same problem. I intented to change my ROM with an WM6 but it faild and the PDA is some kind dead it freezes in the boot screen. is there some tool to change the rom to an original HTC rom or thre is no help. I hope somebady can help me. the version of the ROM that apears on the screen is:
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 4.0.0.0
I've tried to :
Hello...
In bootloader run USPL
It run, to 0% >> to 100% but right after : error 270
Still block...
Trux 13
hmm i don`t know how i can get the device to boot loader mode can u tell me how
Bootloader
Go in ths Thread :
http://forum.xda-developers.com/showthread.php?t=306880
Trux13
hi i solved my problem i used one spanish version of the WM6 for P3300 and it works if u want hire is the link http://www.megaupload.com/es/?d=YZOQEF4H
u can install it and then change to one on english its what i will do today and i saw how to enter in 3 color bootloader mode ON/OFF boton + VOCAL + RESTART then holding the ON/OFF + VOCAL
Stillnot working
I tried your *.exe file but not working
Trux
me too . always the error
ipl 1,14,0001
spl 1,14,0000
g 02 67 90
os 1,14,00
i ll be crzy! jesus! someone help me!
how to run the uspl on this tm phone ?
Has anybody solved the problem? I have exactly same errors and can't do anything
Try This:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
i tried this already. Invalid certificate any other ideas ?
woojtekr said:
i tried this already. Invalid certificate any other ideas ?
Click to expand...
Click to collapse
Hi
if you need still help GG9735272
the only solution !!!!
woojtekr said:
Has anybody solved the problem? I have exactly same errors and can't do anything
Click to expand...
Click to collapse
to everybody who is stuck at HTC screen. The only,and i mean the ONLY way to fix this is to find the original rom for your provider !!! belive me,i`ve tried every possible other way.
SD Card Flashing wont work coz your devices are probably CID Locked,so it goes only to 3% flashing and restarts.Finally I found original o2 ROM (German) and it worked like a charm Even the original o2 (English) ROM did NOT work,it had to be the German one,coz probably the device came with German ROM originally !!!.
So my suggestion is,stop trying to flash it with different ROM`s and spend some time finding original ROM from your provider and it has to be the same language as your provider. even if it`s WM6 and your device was originally was WM5,as long as its from your provider and same language it should flash with no problem.I spent 2 weeks to find this out ))
Good Luck to everybody ))
savich said:
to everybody who is stuck at HTC screen. The only,and i mean the ONLY way to fix this is to find the original rom for your provider !!! belive me,i`ve tried every possible other way.
SD Card Flashing wont work coz your devices are probably CID Locked,so it goes only to 3% flashing and restarts.Finally I found original o2 ROM (German) and it worked like a charm Even the original o2 (English) ROM did NOT work,it had to be the German one,coz probably the device came with German ROM originally !!!.
So my suggestion is,stop trying to flash it with different ROM`s and spend some time finding original ROM from your provider and it has to be the same language as your provider. even if it`s WM6 and your device was originally was WM5,as long as its from your provider and same language it should flash with no problem.I spent 2 weeks to find this out ))
Good Luck to everybody ))
Click to expand...
Click to collapse
I have the same problem and I've come to believe that this is the only solution. Just one thing: I didn't back up ROM before I tried to flash (talk about a noob mistake).
So, I ask, I plead, I beg... can anyone tell me where to get an original Orange France ROM for the Artemis (SPV M650)?
To my knowlegde you cant backup the rom from your device. whenever you change your rom, use the USPL tool. It is a golden rule until something better is made.
Here are some tips:
First make sure you have a original factory rom from your provider/brand/etc.
Check with a soft reset if code: SPL 1.11000 appears on the the boot screen. (then it is CID unlocked) Any other number and it is locked so you have to USPL first before you change to any custom rom.
If you flash a factory rom then the SPL resets to a non SPL 1.1100 number again. Use USPL to CID unlock again.
Also avoid Vista (especially 64bit) to use the USPL tool. Do it on a windows XP machine. Also there reports of glitches in the usb connection and active sync when doing upgrades or USPL. So keep you system as clean as possible. Dont use a USB hub and disconnect any other usb devices just to make sure.
Also remove your SD / SDHC card before doing a upgrade.
Sometimes the new rom misses some stuff when flashing. When this happens just flash the rom again. But first make sure if its still CID unlocked by soft reseting and check if SPL 1.1100 else use USPL first.
Even if you did all that, there still can be things that can go wrong. So if you absolutely confident to do a custom rom then do it. Otherwise use original upgrades from your provider
brim
help i breaked my htc p3300
jai lereur 270 jai essaiyer tous les rom rien ne marche ::
p3300 work again
p3300 movistar work again
Hey people,
I have got on nice MDA with ipl and spl 2.21.0001
me problem is i have no idea wath did happend to it.
the MDA starts up shows T-Mobile ... an go to the Bootloaderscreen (red IPL2.21.0001, green spl 2.2.0001, blue, with)
so i have tried to flash it now with WM5 from T-Mobil image ver 2.26.10.105 (from this nice Board here
The flash tool shows no image information of my MDA but the posibility i there to push the update button. If i do that the update tool trys to flash a few seconds and stops with error code 294 (invalid vender id). on the MDA is noch change (still bootloaderscreen)
some one of you has an idea wath could be happend to this device ?
or an idea wath can i doo ?
Yes!!!
Your problem... is NOT READ Enough!
So please read how to make a hardSPL cause your wizard is G4....
if you do it well you can upgrade whatever you want but for this time... you need to exit bootloader screen so... perform sofresets! or hardreset!
Keep reading for more chances...
You don't need to apply HardSPL or SoftSPL to flash an official stock rom.
Which language or version was working primarily on the phone before you flashed t-mobile 2.26 ?
Secondly download 'RUU_NoId' or 'RUU_MUN' and replace it with the RUU in the rom and Run the replaced RUU,hope it'll work.
Hi,
and thanks for the answers.
i do not know wath was befor on it. i have get it with the information that there was an klabel inside for the keybord not in the slot .... and after "reparing" - the mda do not boot.
up to now i have update it with orginal firmware and it runs again ... so peraps someone has talk **** to me ?! - now i think it was a bad flash
p.s. the vendor id problem was my mistake, was the wrong update