Hi Folks
I've broken something. I know, it had to happen. All this "playing around" with my new toy (No, not like that! )
Going to PocketWord and it'll open something that I don't recall putting in there. This turns out to be a file in the "My Documents" called "CONFIG" that had loads of characters that are not letters, you know, like symbols and the like?
If I goto Menu / File / New it gives the message
"A problem with the document was encountered and it cannot be opened".
I suspect I've deleted something I shouldn't have Help?!
Elwyn M3100 said:
Hi Folks
I've broken something. I know, it had to happen. All this "playing around" with my new toy (No, not like that! )
Going to PocketWord and it'll open something that I don't recall putting in there. This turns out to be a file in the "My Documents" called "CONFIG" that had loads of characters that are not letters, you know, like symbols and the like?
If I goto Menu / File / New it gives the message
"A problem with the document was encountered and it cannot be opened".
I suspect I've deleted something I shouldn't have Help?!
Click to expand...
Click to collapse
Ok... First I don't think the config file in my documents is vital and I would delete it. (if your concerned about it then copy it somewhere-else and then delete.
On a PC Word uses a template for blank documents called normal.dot but on Pocket Word it uses blank.dot This file should be present in the windows folder in main memory.
After deleting the config file, I would try word again.
If it still fails to open a new wod doc, then look to make sure the template file blank.dot is present.
Mike
Hi Mike
I checked and there wasn't a blank.dot file in the windows folder, so I managed to open an word doc I already had, blanked it and saved it as blank.dot where you suggested. I closed word and tried again only to find the same error message.
So does this rule out an error with that side of word, and otherwise what would you suggest?
TIA
Elwyn M3100 said:
Hi Mike
I checked and there wasn't a blank.dot file in the windows folder, so I managed to open an word doc I already had, blanked it and saved it as blank.dot where you suggested. I closed word and tried again only to find the same error message.
So does this rule out an error with that side of word, and otherwise what would you suggest?
TIA
Click to expand...
Click to collapse
This is a little mysterious! Firstly because the original blank .dot is protected and should not be able to be removed normally. I suspect it's become corrupted. Still the replacement should have been ok. However, lets hope all your templates are not corrupted. Open a doc in word and go to menu>tools>options>default template and choose another, say memo. Close out of word and reenter. It should open and when you press new a memo should appear. A bit of a pain but until a better solution comes along you can always delete the memo lines and treat as a blank doc.
Will check around to see if there is another way to replace blank.dot
Mike
Thanks, I've had a look in the options and for "Templates" it is blank. There are NO templates at all on the machine
Elwyn M3100 said:
Thanks, I've had a look in the options and for "Templates" it is blank. There are NO templates at all on the machine
Click to expand...
Click to collapse
Good grief what have you been upto - thought I was the only one who manged that sort of thing!!.
Perhaps you could PM POF and see if he knows a way of reinstalling Word or using the ROM cab files to re-install without having to do a full hard reset. Failing this all you could do would be to create your own blank template but it would not automatically open when you tap new because I think New can only be set to one of the four standard templates - Blank, Memo, Metting Notes and one other I forget. Certainly when I created a template and put it in the templates folder it listed the official four but not mine in the drop down list for the new document default template. (i.e the list that's now empty for you)
Mike
mikechannon said:
Good grief what have you been upto - thought I was the only one who manged that sort of thing!!.
Click to expand...
Click to collapse
Nope, no chance of that....
There are plenty of "us" around
One shall, er, carefully dig
Ah ha!
I have found that I do actually have some files in the windows directory that are templates.
blank meeting memo phone todo
These did momentarily have Word Template icons moments ago, and tried to go in via Word again but now the icons match up with notes.
blank 0b
meeting 1.55k
memo 2.06k
phone 1.96k
todo 3.02k
Right clicking over "blank" reveals that it is read only. I have tried but I cannot remove the RO flag. I am hoping that because the file is zero bytes then this is causing the problems, which are still there
Onwards eh!
Edit: The 0 byte file is actually a memo file. The Word templates are 7kb apart from Todo which is 14k...
Elwyn M3100 said:
Ah ha!
I have found that I do actually have some files in the windows directory that are templates.
blank meeting memo phone todo
These did momentarily have Word Template icons moments ago, and tried to go in via Word again but now the icons match up with notes.
blank 0b
meeting 1.55k
memo 2.06k
phone 1.96k
todo 3.02k
Right clicking over "blank" reveals that it is read only. I have tried but I cannot remove the RO flag. I am hoping that because the file is zero bytes then this is causing the problems, which are still there
Onwards eh!
Edit: The 0 byte file is actually a memo file. The Word templates are 7kb apart from Todo which is 14k...
Click to expand...
Click to collapse
Those file sizes look fine apart from blank.dot which should also be 7kb.
On mine I just checked the templates and they should open directly from the windows directly. They all have word icons.
Mike
I have the notes templates and the word templates. Alas late night scrolling across the PDA got me confused.
Do you know of a way to make the files non read only? I don't seem to be able to change that at all? I've tried in Windows and on the PDA.
Although, I have now fixed the ActivSync issue so it doesn't keep disconnecting Grr Hubs Grr.
Elwyn M3100 said:
I have the notes templates and the word templates. Alas late night scrolling across the PDA got me confused.
Do you know of a way to make the files non read only? I don't seem to be able to change that at all? I've tried in Windows and on the PDA.
Although, I have now fixed the ActivSync issue so it doesn't keep disconnecting Grr Hubs Grr.
Click to expand...
Click to collapse
Nope, I tried reseting read only tag on both PDA and PC as well, no joy. I have posted a thread asking if anyone knows how to re-install an application without hard re-set. I believe it is possible if you have extended rom cabs showing but which cabs as I do not see one clearly marked Word.cab or something similar. The joys!!!
Mike
Thank you Mike for all your help.
I've not even breached the option of ROMs yet or even dabbled in it, and I don't think I've got the guts to juuuuuust yet
If all else then I shall do a reset, a hard reset.
I seem to have this problem also, interestingly. Today when I tried to open the word mobile program, I got this prompt saying that I can't open a new word document due to some error and brings me to my storage card wif all the word documents which I can open wif ease. What seems to be the problem? Any way I can reinstall this program again without hard resetting? I am pretty sure it's not some software conflicts, maybe I accidentally removed some shared files with memmaid.
YES!! Finally I got it. I shifted my documents folder with the sub folder 'templates' to the storage card before so now I just placed back the templates subfolder to the device's My Documents folder and that basically solved my problem!
Related
Hi y'all,
been tidying up my directories on the Xda mini (what a mess on the std install).
Since then I cannot open a new word document, comes back with "a problem with the document has been encountered and it cannot be opened"
I suspect I may have deleted a template file that Word uses when opening new doc's by mistake (maybe like the normal.dot in full blown word?)
Anyone know if this is the case, and if so what the file name would be?
Thanks
Paul.
You,ve probably deleted some templates in \my documents\templates on your device.
Find them all enclosed including a zoom fix for pocket excel - normal.xlt that gives excel 75% zoom if you use it as a template for your excel sheets.
next question....
Thanks Mark,
have downloaded the templates but Word is still not seeing them.
When I go "menu" - "options" the "defalt template" drop down is empty
Part of my original issue is the illogical structure of the directories on the device with what appears to be multiple instances of folders eg :\documents and setting\my documents as well as \my documents
Equally their are a number of "templates" folders around
Any suggestions on how I can alter where Word looks for the templates?
Paul.
The template that is like normal.dot is blank document.dot and if word is not seeing this you must of deleted something else. Are you sure you have placed the templates in the right place, so it should be on the device memory \my documents\templates\blank document.dot
If it is and still not working suggest you do a hard reset - but all is not lost if you don't want all the o2 extras that fill your device and slow it down once the hard reset is almost complete and the o2 stuff is just about to install do a quick soft reset and the extras wont be installed (be warned you have only 3 secs to do this)
Word Mobile templates
I cannot open this zip file which is suppose to contain template files for Word Mobile to work properly.
Attached Files
templates_434.zip (252.3 KB, 60 views)
I downloaded the zip and it opened just fine - what was the error you encountered? did you try unzip on pc and ppc.
If no joy - give me your email addy and i send them to you.
Word Mobile templates
I get an error from Winzip -- Cannot open file: It does not appear to be a valid archive. If you downloaded this file, try downloading it again." (I have, several times, and I tried opening the file instead of downloading it.)
Also, my issue is that WM6 Standard (smartphone) Word Mobile will not open Word files, but Excel Mobile and Power Point Mobile work fine.
I am running WM6 on a T-Mobile Dash.
The issue you discuss appears to be related to Pocket PCs, not Smartphones.
If you think they will help, please email the template files.
Ray
[email protected]
I've searched but cannot find any info about this.
I recently upgraded to a 8125 (WM5)from a iPAQ 2215 (Pocket PC 4.20). Now when editing most (not all) of my Excel files I get a "unsupported content" when I try to save it. It give me the option of saving as another name, discard or cancel.
It doesn't matter what I edit, whether it is text or a number. The files do not have any macros, just simple equations.
My desktop is running WinXP with Office 2003.
Thanks in advance.
Excel file save error
Sledutah said:
I've searched but cannot find any info about this.
I recently upgraded to a 8125 (WM5)from a iPAQ 2215 (Pocket PC 4.20). Now when editing most (not all) of my Excel files I get a "unsupported content" when I try to save it. It give me the option of saving as another name, discard or cancel.
It doesn't matter what I edit, whether it is text or a number. The files do not have any macros, just simple equations.
My desktop is running WinXP with Office 2003.
Thanks in advance.
Click to expand...
Click to collapse
I get something similar: "An error occurred saving 'filename'", and then the file closes with no modifications.
I have to do a File Save As... and give the file a new, slightly different name if I want to save new data. This doesn't happen with every file I use, but it has happened with files imported via ActiveSync as well as with files I have created on the 8125 itself
Hmmm, I never had any problems! Can one of you post one if this mysterious files? But take off your personal information and critical data first from that file! Would be interesting to see if it happens on mine too ...
When I get the error, I can save it as another name with no problem. It is a hassle, because I edit the files on the desktop PC and the 8125. I have not done any upgrades to the 8125, it is the way I got it from Cingular, except for a few programs that I installed which are the same ones I had on my older iPAQ.
I uploaded one of the files that I have the problem with. I cleared all the data and left the equations. I checked it after I did this and it still will not save without making me change the filename.
Works fine on mine! Had no problems adding contents and saving it! Maybe you had the file open twice? This happens if you do not close Excel properly or if you open it by clicking on the file. Excel might have been already open with that file in the background and therefore you only would be able to save it under a different name since the file still would be in use.
Thanks for giving it a try. The problem is not that it's already open. If I do a soft reset, then open the file, modify it and then close I get the message.
Post your PDA specs.
I have had this problem when saving to the Memory card. When it does this I just save to main memory and copy over via Resco, not ideal...but it beats carrying a laptop.
kegobeer said:
Post your PDA specs.
Click to expand...
Click to collapse
Cingular 8215
WM5 OS 5.1.195
IPL 2/25
SPL 2/25
GSM 02.25.11
OS 2.25.11.1
I haven't updated anything, just installed a few programs, the same ones I used on my iPAQ.
Files are on the PDA, not SD card. I even tried removing the card, no change.
Has this always happened?
kegobeer said:
Has this always happened?
Click to expand...
Click to collapse
Yes, but I've only had it for about 3 weeks. The files are all the same that I've used with my iPAQ with no problems.
Yes it happens....
Check this, http://softmaker.com/english/ofp_en.htm
It has to be a very good reason to have this company in business selling substitutes for pexcel and pword. According to what they advertise that reason is that pexcel and pword are not 100% compatible with the desktop versions, so whenever an xls or doc file made in desktop is modified and saved under the same name in a PPC is very likely that some formats, functions etc. will be affected or lost, so M$ PPC awares (probably not in the best way) the user that the files made in the desktop are going to change and will lost some features, formatting, etc.
I was having the same problem on an iPaq hx4700 running Windows Mobile 5. Some Excel Mobile files would only save changes when I used save as and gave them another name. I found the following link while trying to resolve the issue:
http://forums.pocketpcfaq.com/viewtopic.php?t=17048
(g0lg0thaZA Feb 15, 2007 4:16 am)
I searched my device for Temp0FOO files and deleted them. After that I was able to make changes to spreadsheets and save them without changing the name.
Excel Mobile Save Fix!
XeonXeon said:
I was having the same problem on an iPaq hx4700 running Windows Mobile 5. Some Excel Mobile files would only save changes when I used save as and gave them another name. I found the following link while trying to resolve the issue:
http://forums.pocketpcfaq.com/viewtopic.php?t=17048
(g0lg0thaZA Feb 15, 2007 4:16 am)
I searched my device for Temp0FOO files and deleted them. After that I was able to make changes to spreadsheets and save them without changing the name.
Click to expand...
Click to collapse
Oh-my-gosh! This fixed my problem!
I read that link, I searched for that file, found 2 of them, deleted them, and now I can modify an Excel file, hit the X close button, and the file gets saved just like it shoulda!
A big note of thanks and sigh of relief for this fix!
I have tried to search for the mentioned file Temp0FOO but couldn't find it on my Omnia anyone can help me please
For some strange reasons, now I'm unable to open word document unless the file size is real small like less than 10KB in size. I was once able to open files up to 110kB in size (although it seems to take ages for the spinning colored pie to render the vertical scroll bar).
The error message that I get is "A problem with the document was encountered and it cannot be opened."
I've googled this. Some suggest that it is due to missing template, which is certainly not so in my case. My template folder and files are sitting nicely in the my document folder in the device memory. Some also suggested that word mobile is unable to read desktop document files and that we need to save it as RTF file. I tried this, but it does not solve the problem. In fact, the document was created with word mobile originally.
Is anyone of you having this problem too?
Oh dear, this is a problem known to microsoft. This is no good.
http://support.microsoft.com/kb/911420
I had seen the same error message mentioned in this article appearing on my device before but I dismissed it as it came and went too quickly.
In this support note, microsoft thinks that it happens if the document is in SD card. But I have the same problem even if the document is on microdrive and device memory.
I transferred my document from SD card to the device memory and tried to load it in, and still have the same problem.
hrmm ive never had trouble opening any size word doc. Although conceivably I didnt start opening word docs much until I had TextMaker 2006 installed. But in all my times on WM ive never come across I doc I wasnt unable to open, except for word 2007 docx files, but thats due to compatibility so.
I was once able to open any size document too. Although I has seen thoses error messages, I was able to open with repeated trying. Then now it becomes very predictable - no problem withbreal tiny files, but errors if the files are big.
May be time for hard reset again?
eaglesteve said:
I was once able to open any size document too. Although I has seen thoses error messages, I was able to open with repeated trying. Then now it becomes very predictable - no problem withbreal tiny files, but errors if the files are big.
May be time for hard reset again?
Click to expand...
Click to collapse
I also experienced a lot of problems after Textmaker installed.
I have no such problems with Textmaker and Planmaker installed...
jlingo said:
I also experienced a lot of problems after Textmaker installed.
Click to expand...
Click to collapse
what's the nature of your problem? is it with text maker or word? Is it the same or different problem?
This is wierd. All of a sudden I am able to open all files regardless of size again. Did'nt have to do any hard reset.
I Want To Know IF There Is Any Way That I Can Hide Programs Or Mask Them SO That They Don't Show Up On The Programs List And Also Hide Any Files Associated With The Program
HELP
Any Help Please
It's difficult to answer without knowing what you are trying to accomplish. Why would you want to hide programs on your own phone?
Anyway, your best luck will be with small programs, the kind that run as a single executable, that you can put somewhere on the SD card.
Im Sure Im Not The Only One With These Issues
My Girlfriend Was Always Questioning Me About Why I Always Kept My Phone Locked And Would Not Answer It When I Was Around Her So I Put A Program Called Magicall On My Phone I Don't Know If Your Familiar With That But You Can Screen Certain Calls Well As She Always Does Whenever I Leave My Phone Unlocked She Went Thru It When I Was In The Shower She Saw The Program But Couldn't Get Into It Sp She Went On The Internet To Find Out What It Was And Then She Wanted To Know Why It Was On My Phone And We've Been Arguing Ever Since So Please Help Me Id You Can It Would Be Much Appreciated Thank You In Advance
I don't have a technical answer..sounds more like it's a trust issue. Besides locking the phone, only thing I can think of is install on sd...but then you have to remember to remove the sd card when you put the phone down.
If this was a pc, I'd say install the private stuff on an encrypted volume like TrueCrypt. Not sure if there's anything like that for ppc.
This would probably work...
http://www.freewarepocketpc.net/ppc-download-freeotfe4pda-v3-00.html
But I'm telling you, it will be a real PITA to manage a setup like this. Methinks it would be easier to just get straight with the gf, but I know very little.
i tried to download the program but it said that it was not a valid ppc application any more suggestions
old_school_dave said:
This would probably work...
http://www.freewarepocketpc.net/ppc-download-freeotfe4pda-v3-00.html
But I'm telling you, it will be a real PITA to manage a setup like this. Methinks it would be easier to just get straight with the gf, but I know very little.
Click to expand...
Click to collapse
Here is a solution if you are not trying to be open with gf:
Have the program cab on sd card renamed to something that would never be used by gf, such as erasememory.cab. Use program when you need it. I don't think this will work if you are trying to use a program to keep her from finding out about other gf, you may want to use the thing from Men in Black that erases her memory.
The program from earlier, or some other virtual encryption device may work, but you may have issues due to the fact that you are running a program tied into so many others (phone, sms, etc). You may make your phone pretty unstable.
Why don't you tell her that you accidently replied to a text that sent you spam messages and you were trying some freeware program to block, or that you were getting a call from some random number that was harrassing you and you were trying this program to see if it would stop the calls. You gotta think on your feet if you are going to prevent the ***** session after she found out. Careful if she pulls the verizon/sprint bill and checks sms/calls.
if what im trying to do is not possible then is there anyway to change the icon or mask the program im up for any suggestions right now other than being honest cause I love my women
"i tried to download the program but it said that it was not a valid ppc application any more suggestions"
exe files in general are install ment to be run on the pc with the pda connected not directly on the pda!
about hiding programs then
\windows\start menu\programs and remove the shortcut goes along way
after I deleted the shortcut I tried going into my documents to open the program but it didn't open is there another way to open it also I tried changing the name of the program with this method and it worked but is there a way I can change the icon because that would be perfect thanks for your input it is much APPRECIATED and if there's anything I can help you with let me know
rsturgis0601 said:
after I deleted the shortcut I tried going into my documents to open the program but it didn't open is there another way to open it also I tried changing the name of the program with this method and it worked but is there a way I can change the icon because that would be perfect thanks for your input it is much APPRECIATED and if there's anything I can help you with let me know
Click to expand...
Click to collapse
Here is how you mask the icon.
Use total commander and navigate to Windows/Start Menu/Programs and find that .lnk file: delete it.
Find another .lnk file and copy to pasteboard. Go to another folder and paste it there (just as long as the other folder doesn't have the same link). Go into properties of that copied link and click on shortcut tab at the top. In the target field, click on File and navigate to Program Files/(DIRECTORY OF YOUR PROGRAM)/(EXECUTABLE FILE THAT OPENS YOUR PROGRAM) and click OK. Click File/Rename and call it something benign or something she wont click (like Erase Phone Memory).
You will then cut to pasteboard and navigate back to Windows/Start Menu/Programs and paste that file. You will then use that file to start the program. You could also change the name of the directory folder in program files if she knows how to navigate around in total commander/ file explorer. It will still show up in task manager as what it is though, and same goes for x button/ pocket plus.
Thanks Got It You Just Helped Me Take My Relationships To A Whole New Level
rsturgis0601 said:
Thanks Got It You Just Helped Me Take My Relationships To A Whole New Level
Click to expand...
Click to collapse
Glad to help you be so devious. Happy mongering.
I deleted the following shortcuts "Transformers", "MobiTV", "Market Place" and "YouTube" from Windows/Start Menu/Program, thinking they were redundant since they were already on the home screen. But while the icons are still on the home screen, I can't get to the four programs by tapping on the icons; instead, I got the error message about "Shortcut Target" saying "Error opening the shortcut or locating the target filename".
I was able to find the "MobiTV" and "Transformers" folders, but I could not create shortcuts from the .exe files since the "Create shortcut" was gray and did not respond to taps. My questions are: (1) How do I re-create those four shortcuts that would make the icons on the home screen work again? and more generally, (2) How do I create shortcuts (gray-colored) for any .exe files? Any suggestions and help will be much appreciated.
I know that the "Total Commander" app let's you create links where File Explorer doesn't, but I've never actually messed with that part of the app very often.
Tons of folks are complaining about the movie icon, as far as I know no one has found a way to fix it once you break it
You got it the wrong way round.
First, click on "Copy" option for the exe file that you wish to make a shortcut.
Then go to \Windows\Start Menu\Programs, click on "Menu", the option "Paste shortcut" should be available now.
Re-created shortcut for MobiTV, but not for the other three
After seeing your answer, I realized I should have performed them on my HD2, instead of on my synced desktop PC! As long it is a .exe file, a shortcut can always be created for it on Windows program page by using the method you described. Thanks Zentury!
However, I could only recover (re-create) the shortcut for MobiTV since it is a single .exe file. I could not even find where the .exe files are for YouTube and Market Place to re-create the shortcuts for them... As for Transformers, since it is a folder with two .exe files, I could only create shortcuts for each of the two separately on Windows program page, and the icon on the home screen still does not work. Any ideas?
jcc266 said:
After seeing your answer, I realized I should have performed them on my HD2, instead of on my synced desktop PC! As long it is a .exe file, a shortcut can always be created for it on Windows program page by using the method you described. Thanks Zentury!
However, I could only recover (re-create) the shortcut for MobiTV since it is a single .exe file. I could not even find where the .exe files are for YouTube and Market Place to re-create the shortcuts for them... As for Transformers, since it is a folder with two .exe files, I could only create shortcuts for each of the two separately on Windows program page, and the icon on the home screen still does not work. Any ideas?
Click to expand...
Click to collapse
As for the Transformer Shortcuts use the cab posted, The other exe your looking for are in the windows folder on the phone. You Could always reinstall marketplace, for that shortcut.
Thanks for the attached .cab file! I downloaded the .cab file for Transformers but am wondering where should I put it: in the Device or in the Storage Card, and in what folder?
I did find Market Place and YouTube folders only in the Device's Windows folder, but where are the .exe files for them?! In Market Place folder, there is only one tiny file called ClientLog0 (263B); and in YouTube folder, there are four folders and hundreds jpeg files.... I did the search on my desktop PC for files in HD2 and know there is one YouTube.exc but don't know which specific folder it is in... Without getting to these .exe files, I don't know how to restore/reinstall the shortcuts for them. Please kindly advise. Thanks.
jcc266 said:
Thanks for the attached .cab file! I downloaded the .cab file for Transformers but am wondering where should I put it: in the Device or in the Storage Card, and in what folder?
I did find Market Place and YouTube folders only in the Device's Windows folder, but where are the .exe files for them?! In Market Place folder, there is only one tiny file called ClientLog0 (263B); and in YouTube folder, there are four folders and hundreds jpeg files.... I did the search on my desktop PC for files in HD2 and know there is one YouTube.exc but don't know which specific folder it is in... Without getting to these .exe files, I don't know how to restore/reinstall the shortcuts for them. Please kindly advise. Thanks.
Click to expand...
Click to collapse
it doesnt matter where you copy the cab file do as long as you know where it is, once it is on the device use the file explorer to find it and run it. Try this cab for the other 2 link files
I tried the Transformers.cab on my Device but failed to install because of "not sufficient system permissions". Earlier, I found Transformers.lnk in Device Windows and paste it on Windows/Start Menu/Program. Tapping on the home screen Transformer button will take me to the two Transformers movies, but I lost the nice Transformers icon on the home screen; instead, I only got the boring old Windows icon in its place. How do I get the nice Transformers icon back on the home screen?
I got YouTube shortcut back to work OK now, but Marketplace shortcut still does not work. The .cab file for Marketplace installed without any error message ("successfully installed on your device") and the Marketplace icon stays on the home screen, but tapping on it does not take me to its web page. Can you suggest anything I can try? Thanks again.
jcc266 said:
I tried the Transformers.cab on my Device but failed to install because of "not sufficient system permissions". Earlier, I found Transformers.lnk in Device Windows and paste it on Windows/Start Menu/Program. Tapping on the home screen Transformer button will take me to the two Transformers movies, but I lost the nice Transformers icon on the home screen; instead, I only got the boring old Windows icon in its place. How do I get the nice Transformers icon back on the home screen?
I got YouTube shortcut back to work OK now, but Marketplace shortcut still does not work. The .cab file for Marketplace installed without any error message ("successfully installed on your device") and the Marketplace icon stays on the home screen, but tapping on it does not take me to its web page. Can you suggest anything I can try? Thanks again.
Click to expand...
Click to collapse
I would just reinstall the marketplace cab and that should fix it. Not real sure on the icon.
I reinstalled the Marketplace.cab file a few times on my Device, still no luck - tapping on its icon on the home screen won't point to the right web page, only the same error message... The strange thing to me is there seems no .exe file for Marketplace on the device, so ... how did it ever get started?
jcc266 said:
I reinstalled the Marketplace.cab file a few times on my Device, still no luck - tapping on its icon on the home screen won't point to the right web page, only the same error message... The strange thing to me is there seems no .exe file for Marketplace on the device, so ... how did it ever get started?
Click to expand...
Click to collapse
Hi, just catching up with the latest on your problem resolution. (Note: I'm on the other side of the ocean.)
I took a look at the contents of Marketplace.lnk on my HD2 and the file location is "\Windows\WMMarketplace.exe".
Thank for taking the time to look it up - now I know why I couldn't find its .exe file on the device: it's WMMarketplace.exe, not just Marketplace.exe! Next time when I do the "search", I will use the wild card symbol * in the search string. Some valuable lesson learned!
Anyway, the shortcut problem for Marketplace was solved last night after I found another Marketplace.cab (116kB) provide by zelendel in another earlier xda forum thread. The youtube & marketplace.cab file I've been using and did not work is only about 2kB in size so apparently was not a good .cab file.
The only remaining "missing shortcut" problem I have is now changed to "missing icon" for Transformers on the home screen. The two Transformers.cab files I got from the xda forum all have the error message "not sufficient system permissions" when I tried to install them. Since the installations were "unsuccessful", the ugly blank-look icon in place for Transformers on the home screen still keeps staring back at me ...
Anyone got a Transformers.cab to share that would not cause the "unsuccessful" verdict and would restore the nifty Transformers icon on the home screen? Thanks!
Ive just downloaded that Transformers cab thinking it was going to the movie file or some funky robotic program and all i got was a shortcut leading to nothing??
Hmm, now how the hell do i remove it? Ive deleted the cab file but the shortcut is still visible on the start menu.
Thai-wronghorse said:
Ive just downloaded that Transformers cab thinking it was going to the movie file or some funky robotic program and all i got was a shortcut leading to nothing??
Click to expand...
Click to collapse
Thai-wronghorse said:
Hmm, now how the hell do i remove it? Ive deleted the cab file but the shortcut is still visible on the start menu.
Click to expand...
Click to collapse
You probably aren't running the Tmo ROM, right? The transformers link only opens up the player for the movies that are provided to tmo owners on the included 16GB SD card...so all you did was indeed install a "link to nowhere".
You'll need to navigate to /windows/start menu on the phone, and delete the "transformers.lnk" file there.
there is an app on freewarepocketpc.net called "LnkMgr", that you can use to create shortcuts ...
works ok ..