Related
Hi , all something strange happened to my XDA II SD Memory card!!! , i was installing an application on the SD Card and i went to the SD Card to explore it searching for something while the XDA while installing but i couldn't see all my old files , when i check the memory status i can see that i am using 70MB if the 256MB but i can't locate the files.
can any one help.
I had the same problem with a Sandisk 256mb card.
I've found that it works fine with a Lexar 128mb card though.
So it looks like the XDA2 has problems with SD cards as well as a completely duff bluetooth implementation.
Re: SD memory Card files disappeared
raheeeb said:
Hi , all something strange happened to my XDA II SD Memory card!!! , i was installing an application on the SD Card and i went to the SD Card to explore it searching for something while the XDA while installing but i couldn't see all my old files , when i check the memory status i can see that i am using 70MB if the 256MB but i can't locate the files.
can any one help.
Click to expand...
Click to collapse
Man thats bad news, have you tried doing a soft reset.
Also if you have a PC card SD reader try running Scandisk on the
card.
BTW as you can see it not a good idea to access your SD card while
programs/files are being installed / written to it.
HTH
Sandisk
ok interesting , i am also using Sandisk 256MB!!!
i tried soft reset and it didn't help.i will try to find a PC reader and see if i can get anything out of it or i might try to use it on my brother XDA 1 because most of the files were used on my old XDA with PPC2002 rom.
Hurray, its not just me then. I have a 128mb dane elec card and 70meg has disapeared. Im not sure if anything was on teh card previously and I dont have a card reader to check. Its most annoying!
Storage Card slot kaput
I bought a brand new generic 2GB SD card and had it working for a day. It just wasn't working anymore one morning I have left my XDA II overnight on the cradle. Now it wont accept any MMC or SD card I put on it. Any idea what could have gone wrong?
When it was still working I tried copying media files on it (in Microsoft knowledgebase they confirmed in order for media files to work in storage cards you have to create My Documents folder did this on the several cards I tested but to no avail)
The storage card I bought was 2 GB, O2 site says XDA II has been tested on 1GB storage cards--could I have burnt my SD card slot?
Maybe the card brand was too generic-- but then I tried other branded SD and MMC cards after the day my slot stopped recognizing and it still didn't recognize Sandisk (512) and Leica cards (64MB)
The SD card in question is still detected if you put it in a card reader then connect it to a PC
Help badly needed, I'm losing so much productivity with very small storage/ROM space
Hanshake said:
The storage card I bought was 2 GB, O2 site says XDA II has been tested on 1GB storage cards--could I have burnt my SD card slot?
Click to expand...
Click to collapse
Well, I'm using Kingston 2GB SD card and it works perfect... and it's a high speed card.
You may have your SD slot broken. My slot for example from time to time gets the card disconnected (let's say, every few hours), and I have to pull it off and put back in.
in a sdcard reader undelete tools from pc can recover files from sd cards as they can with harddisk
like undelte plus
I just bought a 2gb sandisk sd card
it is recognised by the magician but each time it switchs to stand by mode the "memory card" file disappears...So I have to take it out and to insert it again (two times) in order to see it again.
Is it normal ? or there's a problem with this card ?
thanks
:shock:
up
Good to read, Storage to the people!
Take a look @ the card params too. Somehow a magician communicates better with a fat(16) card than fat32.
Have fun, M
thanks for your comment...
I can only format the sd card with the magician because i don't have a sd card reader for my PC. But with the program I use (FORMAT) I cannot choose FAT 16 or 32 - do you know a soft to do this ?
PHM Pocket Mechanic is very good for this, available on trial
I just received my Sandisk Ultra II 2GB card and it's working fine with my S100 (1.12) and I didn't have to format it when I received it.
However I have just come upon a problem. The card works fine in my S100 and I can copy files to it via ActiveSync. In order to speed things up I just tried putting it in the card reader in my laptop which reported it as unformatted...
Got the Sandisk Ultra 2 2GB for my M500 and it works fine in the phone , my card reader however does not like it either.
However i have sd-cf adapter that i use with my camera , i sloted the sd card in to that and in to the card reader and it works fine at very high speed.
Hope that helps.
C.
Laptop doesn't have CF and I'm reluctant to allow it to format the card in case I suddenly have issues reading it in my S100. :/
hi, i ran a benchmark in my 512mb SD card (unknown brand - missing logo) with pocket mechanic and the results are: Read 5.1X and Write 0.6X. Is it bad?
ok my card reader on my laptop and my S100 must talk a different dialect of SD card because no matter what I do they can't work together.
If I format the card in my S100 and copy files via activesync the laptop reports the card as unformatted.
If I format the card in my laptop and copy files on my pocketpc can't see them.
Size doesn't fit to 2GB Card
Hi I just got my sandisk ultra II 2GB SD Card and at first it worked fine.
Magician recognized it as 2GB then i copied some files from my computer with my SD Card Reader. But after inserting the card into my magician i got some weird looking characters, files, and folders. So I inserted it again in my SD card reader and formatted the card. After that my pc and my magician doesn't recognise the card as 2GB anymore just 1GB .
Any help to solve this problem and to get my 2GB back ?
I too facing the same problem it is detecting as 1 GB instead of 2 GB also the after formatting sd card in card reader made i unformated for ppc and viceversa dam,anybody have a solution for this ?
Today I received my 2GB Sandisk miniSD card from eCost (they sell it for real cheap so I thought I get one). I formatted it with XP (using its supplied SD placeholder) to FAT32. After I placed it on the PDA it reported the following crazy results:
2 GB storage
960 MB used
970 MBs free
In other words, my Wizard (running the latest AKU2 QTek ROM from ~March 22 2006) sees the full 2GB, but can only use 1 GB!!!
I then tried to format it with XP using FAT16, but the SAME problem occured.
Thankfully, I downloaded this utility: http://pocketgear.com/software_detail.asp?id=3191 and I did a "repair" (or format) the miniSD via the PocketPC. THIS utility saved the day! It fromatted the miniSD card correctly! And now I can see and use ALL of the card.
Please note that the problem/bug might not be with XP or the PPC. It might be with the actual SD placeholder, or even the flash reader (hardware bugs). The point is, that somewhere along the way something gets screwed during the formatting. So, if you buy a miniSD 2GB and you get such or other problems, download the StorageTools utility linked above to format (or use "repair") the miniSD card directly in the PocketPC instead of using XP and a SD-placeholder/flash-reader.
BTW, I also posted a review of the QTek 9100 yesterday: http://tuxtops.com/node/749
wow! I'm reading your post and thinking I wrote it! I had the EXACT same problem. I tried another utility (that made my miniSD card unrecognizable to my kjam).....a quick format with my pc, and I was back to only about 1gb of usable space....then i stumbled across storage tools. I ran the repair, and it was fixed! ahhhhh 2gb of space....woohoo!
Same problem, diffrent solution...
I also had the same problem, but found another solution, after trying to reformat, both in ppc and pc and cardreader in printer, card was unreadable by all devices. Therefore, as a last resort, I put the card in my digital camera (nikon s2) wich recogniced the card as unformatted and kindly asked if I would like to format it... after that it worked perfectly
help!!
i got the same problem with my 2G sd card..
i formatted with my PC and now it show only 975mb in my card!!!!!!!!!
i had try to use the StorageTools to repair it via my XDA mini s.. but it still show 975MB.... any idea???
After you used StorageTools to repair the miniSD card, you need to do a soft reset for the PocketPC to recognize the rest of the card.
However, I must tell you, the only clear deal is to FORMAT the card WITH StorageTools and NOT to simply just do a repair.
Hey I have this same problem, but the link to the program is no longer any good. Does anyone know what the name of the application was.
Thanks,
Bought new card
OK- Now I do not know what to do. I just went out and bought a new 2GB scan Disk MiniSD card. When I went to install my data on it, I can only get 1GB on the card. I need 2 GB. Does anyone have any ideas on how to fix this. I thought the last card was bad, but I guess not. This happens on 8125 and in Windows. Both see the card as 2 GB but will error out when you try to add more than 1 GB.
Please help.
Thanks,
The name is that one: storagetools...
I had the same problem and using just the evaluation version of the program was good enough to format mi sd and everything it's ok!
http://storagetools.softonic.com/pocketpc
what is a better format for MiniSD 1G (prob:read/writes slow)
I have a problem with my miniSD card reading and writing WAY too slow.
I think that may have happened when I formated the card as FAT32 partition instead of FAT. This thread seems like it is a helpfull answer, but which would read and write better? Does anyone know?
Thanx in advance.
After using my vario 2 for a while the mem card becomes unusable.
It's shows no free space at all. I have a 1 gb memory that came with my t-mob vario 2.
My mp3 ring tone doesn't work anymore. I have to remove and reinsert the memory card or soft reset the device.
Radio 1.20.31.10
Rom: 1.21.114.3
Any idea's what could be the problem?
Thanks
The smilar problem occured with one of my XDA-II (Himaliya), Even though I have hard reseted the device. Finnaly I have backuped the card through the pc and format the card (on PC) and it wasn't working, even though I have tried 3 other cards and they were working absolutely fine with the device. What I did was to leave the card inside the device for overnight and it was recognisable in the morning, then I took out the card from the device to put the data back from the PC and once I have put the card back in the device the card wasn't recognisable again, So finaly I left the card again in the device overnight and it was recognisable again, then I left the card in the device and put the data back through the syncronisation.
I haven't taken out the card since then because I know there is some recognising problem between the device & the card, its working since then.
My Advice is : To check another card and if that would work then try to sell your current card and buy another.
My advice 02: Try to backup your device, leave the card inside the device and HARD Reset the device & once the device will install newly it should configure the card as well.
I have got very usefull software "storagetools" (trial) by which you can scan, format & defrag the card, you can try it.
GoodLuck
Sidd
Use chkdsk on the PC to check your storage card (instead of any PPC-based software, including Storage Tools). I also recommend the thread at http://www.pocketpcthoughts.com/forums/viewtopic.php?t=39583 on all these q's.
On a related issue concerning problems with microSD cards and the TyTn, I have a problem which I hope you can help me with:
I have a new TyTn (ROM Ver. 1.18.255.3) with a 512mb miniSD card. In the course of my usual usage, the device hanged and after a few minutes of unresponsiveness, I reset the device using the reset button. When it rebooted, the card is no longer recognized by the phone. I used a card reader and WinXP and Mac OSX cannot also recognize it. If I try to format it (XP), XP says that the card cannot be formatted. I tried using it in my Samsung D820 and it cannot also be formatted. I then concluded that the card was defective and bought a new one (512mb).
After using the new card for a week, my TyTn hanged while accessing a program installed in the card. Again after a few minutes of unresponsiveness, I rebooted the phone using the reboot button. When the device booted-- Bam!!! the card can no longer be recognized by my phone! Windows and Mac OSX cannot mount it. I tried the unrecognized card in my Samsung D820 and it is recognized! I inserted the miniSD card (128mb) originally in my D820 in my TyTn and it is recognized/read by the TyTn. I formatted the defective card in the D820 and copied a few files in it and the D820 can read those files but my TyTn can't! I tried the other 128mb card on my TyTn, formatted it and copied files into it and everything's fine.
How come then that the 512mb card can be read by my Samsung phone and not by the TyTn? My TyTn is certainly not defective because It can access the 128mb card that was originally in my D820. As I stated earlier, I have already formatted the 512mb card in my Samsung phone and have transferred files into it (The Samsung phone can read the files written on it).
I have re-inserted the 512mb card numerous times in my TyTn to no avail. I have also rebooted my TyTn several times and still it cannot recognize/read the 512mb card. I am now using the 128mb card that I originally use in my Samsung D820.
If it can help, I have enabled and unlocked my TyTn's extended ROM. I have a few programs that are installed in my Ext ROM.
Thanks!
Similar card problem
I recently purchased the T Mobile MDA Vario2 with the CoPilot 6 software. worked fine for about a week and then the CoPilot software which was running from the memory card started to hang intermittently. The first couple of times a soft reset cured it. Then after about the third soft reset, the memory card was no longer recognised. Tried reading the card via my pc and that couldn't recognise it either.
Took both the phone and card back to T Mobile where a new card was tried, this was recognised immediately so I now have to take the whole CoPilot package back to be replaced.
I have also just orderd a new 1GB sandisk card from Amazon and am now concerned that this is going to be a repeating issue. I wonder how many other owners have had this problem and if it is actually a fault with the Vario2 or wether I have just been unlucky with a dodgy memory card.
Would appreciate other thoughts on this.
Cheers
Matt
I think that enabling the "Advance network functionality" causes the corruption of memory cards.
amf said:
I think that enabling the "Advance network functionality" causes the corruption of memory cards.
Click to expand...
Click to collapse
How did you work that one out?
Elwyn M3100 said:
How did you work that one out?
Click to expand...
Click to collapse
Because when I enabled it, the corruption started.
amf said:
Because when I enabled it, the corruption started.
Click to expand...
Click to collapse
Hmm, yes, I can see where you worked that one out
I'm going to buy Gene and read a lot of possitive oppinions abiut it. But there is a discussion on a russion forum www.4pda.ru about SD card problem. As I understood sometimes it looses SD card and everything on it. The files are shown in wrong symbols and even more - sometimes all data are lost. Does anybody had the problemm? know the solution? Thank you.
Get a reputable brand. I once had that problem with a 512MB in Imate JAM, but my Gene has a 1GB Apacer and Ive never had problems. Get a miniSD with an adapter for more versatility.
i have sumtin to tell
hey i bought my gene say three months back.put a 1 gb Transcend SD...but after some days when i took it out and again inserted it...the memory was lost and it was not formatting also....one fine day suddenly my treo recognized the card..but with only 480 MB.....i had to finally buy a new SD for my Gene...
They say SD card should be inserted after soft reset and will work fine. Also there e few guys tested MMC cards and said there wew no problems.
same here
makler1981 said:
I'm going to buy Gene and read a lot of possitive oppinions abiut it. But there is a discussion on a russion forum www.4pda.ru about SD card problem. As I understood sometimes it looses SD card and everything on it. The files are shown in wrong symbols and even more - sometimes all data are lost. Does anybody had the problemm? know the solution? Thank you.
Click to expand...
Click to collapse
hey i got the same problem to. talk to the HTC CustomerCare. they asked me to get my PPC reflashed. it might be due to some ROM error.
but if u try restarting (soft reset) ur PPC. it will work normally. i have used this technice. it works fine with me.
I recently came to a big problem. my storage card is not working correctly. my ppc takes a lot of time in accessing and reading it and sometimes gets hangs while doing it. i tried formating my device but the problem still exists. then i tried formating the memory card with my PC but again something strange happened. While formatting my pc gave an error msg "Windows Can't Format" or something like tht. i tried to manually delete the contents of my memory card but it says can not access device. I am sure tht my card is not Password lock. i think the problem occured after i used "WM5 Storage" software for my PPC to act as a "Mass Storage Device".
plz some1 tell me how can i fix my memory card.
plz plz plz plz plz help..........
yes, it is definitely a big problem with the SD card problem, i mean not the SD card problem, but the Gene's Problem! i bought it 2 months ago for my wife, comes with a brand new Transcend 1GB SD card, after i've installed all the programs into the SD card, its seems ok at first...BUT, when the Gene go to the standby mode, & u wake up the Gene, the program u have installed in the SD card all GONE!! the device can't find any thing in SD card & it finally hang! it is definitely not bcos i m using lousy brand SD card, i've tried Kingston, Pendrive, Sandisk & it has the same problem! i've called HTC service centre in Malaysia (i m from Malaysia) & they dun even knew about this (& even they gave me taiwan HTC email address, & told me to get an answer from taiwan).....
i have no choice, i have hard reset the device for more than 10 times, believe me, i started my pda phone live 5 years ago, i knew what is hard reset...& i tried more than 5 SD cards... same problem, some of the cards facing difference problem - the data saved in the card became unreadable & weird symbol.
since the service center does not has any solution for it, i have to use my own silly stupid way to prevent the Gene Hang, i have set the device all the time alive & avoid going to standby mode, & the problem solved...never hang again...but...imagine...the battery life ....(sigh).....
i sincerely hope that there is somebody in this forum could help to solve this BIG problem.....
At me too a problem with SD card... Very often on a card some files and folders are renamed in not clear symbols and data vanish.... A problem not only at me.... It at many, and it does not depend on a card memory from insertion Gene...
SD Card got Locked
I installed a software on my Gene, named "WM5 Storage".
it allows u to access ur memory card without activesync, as Mass Storage Device.
after the first use i found my card locked. it was unreadable. my ppc also started hanging. i tried restarting my ppc. now i was able to acces my storage card from file explorer, but it takes around 15-20 minutes and another 15minutes to access the files. when i connect it with my pc, active sync does not detect the SD card. i also tried to format the SD card through a card reader. the card reader reads its root files but couldn't access/open them. when i tried to format it give an error "device not accessible. device not ready.".
i also checked the lock button on the card, it was unlocked. plz some1 help.
plz plz plz..
mee too
GUYS I HAVE ONE CARD WITH ME THAT IS PERFECTLY OK...BUT DOES NOT GET READ IN MY GENE.....IN MY TREO 680 IT SHOWS ONLY HALF MEMORY....AND MY LAPTOP IS ALSO NOT RECOGNISING IT...WAT TO DO....???
I have the same sd card problem.......can anybody tell me the solution?is there same problem with mmc card? if no them i'll buy a new mmc card....plz help me.
Count me in
I had this problem for 5 times and still has it. Actually this happens(based on my experiences and opinion only) when u install some software on the SD card and it damages the file system.
Solution might be not to install apps on SD card or use a RS-DV-MMC which is used in recent Symbian phones.
Give it a try...
And plz post feedback.
Enjoy....