My TyTN is fairly new and I have a question for everybody. Is your USB port tight or does it have a little bit of jiggle to it? I'm used to new devices having a very tight USB port but on the TyTN it's always felt a bit loose. It seems to have a solid connection and it connects/charges/syncs/etc no problem but I'm just concerned if it gets looser that this could become an issue. Has anybody had an issue with this or should I not be concerned?
Mine is rather loose too, but you shouldn't worry about the jack itself. It won't losen up in time (unless you bend the cable while it's attached to TyTN).
If the loose feeling disturbs, you can always bend the metal frame around the jack inwards slightly.
I found that different USB cables have different fit. Like USB cable that came with Holux GPS Slim, fits snuggly on TyTN, unlike the original USB cable that came with it.
Related
I've got an 8525. The USB port on the bottom of the device seems to be really loose. It's quite easy to disloge the headphone or ruin a USB connection by bumping the device.
It's quite a bit looser than any other USB plugs I have, and it didn't start this way. It seems the reliance on using a single port for everything has put a bit of wear on the device. Which, by the way, is but 3 weeks old.
Any suggestions on how to deal with this? I've looked in the forums and searched other resources, but I've not come across similar concerns.
--
I should clarify that the recepticle itself is not loose or out of alignment. It's securely fastened to the internals. The slack and looseness comes when attaching a cable to the port. The cable itself does not seat securely within the port. This is regardless with the cable used, as I have several I tried.
If it is three weeks old the answer is obvious -- return/exchange.
Hi All,
My S200 has served me very well. Unfortunately the mini-usb jack is jacked. My son dropped it in his baby food recently and when I was cleaning it out the little gray plastic cover for the USB wires came off....so when I look inside i see 5 wires coming out...unfortunately one of them is bent and so the USB cable is not working at all...
Is there any way to replace the USB jack? I'm pretty familiar with the insides as i have replaced the speaker and cleaned it out many times...where can i buy a jack if it's even possible? Thanks in advance!
Gujjuman
Just buy one and solder it?
http://www.phonesandmore.nl/Mini-usb-connector-MDA-Vario/
Replacement guide
http://www.modaco.com/content/htc-prophet-prophet-modaco-com/240109/changing-you-prophet-case/
Hi, there are lots of posts about damaged USB ports. I was wondering does anyone saw or uses any cap for USB. It should be something like rubber SD cap. Just plug it into USB and you can reset the phone in complete darkness . And it could be attached to leash loop with little thread not to lose it while on charge/sync. That would also prevent dust from accumulating inside USB port. Anyway I couldn't find anything like that. Maybe some DIY ...
I was thinking the same thing cause i am having to replace my tilt due to breaking the usb port with the stylus. I would love any ideas on how to do a cover.
bump..
sounds like something that should of came with the phone..
This would be a great idea since I have to realign my usb port every once in a while. The only way I can sync with my computer is by using the HTC USB Headphones adapter that came with my 8525. AT$T said that they would not exchange my Tilt for a new one because bent pins are not covered under their warranty due to "personal damange". It's really weird that I can't use my Seidio Cradle to sync with my computer anymore since it has the same proprietary USB jack. It will only charge the unit and if I move the Tilt while plugged in to the cradle, the connection is not always consistant.
healingtouch84 said:
I was thinking the same thing cause i am having to replace my tilt due to breaking the usb port with the stylus. I would love any ideas on how to do a cover.
Click to expand...
Click to collapse
Haha. I thought I was the only one. Went to do a soft reset, wasn't looking, and stabbed the USB by mistake. Didn't notice it wouldn't charge until the next day. Fortunately, I was able to bend the pin (GENTLY) back into place and it works again. BIG sigh of relief
need help please people.
my phone hasnt been charging properly for a few days now, to get it charging now i have to get one of my missis hair bands and wrap it round my phone and then round the usb cable so it stays in , although today it doesnt want to charge at all now .
ive noticed that the connection in the phone is loose and you can move it round a litle bit,
now the bit i need help with , is do i take the phone apart and try to fix it.?. im thinking of doing this but unsure about taking phone apart ( dont think my phone is under warrenty anymore,) and im guessing the usb connection on the phone is fixed onto a board.
is it worth me trying that or should i just take it to a repair shop ?
take a dry toothbrush, give the usb port a good scrub. dirt often builds up in the bottom of the port and stops the usb plug pushing deep enough to get a good contact.
Have a good inspect of the usb port, bright light and magnifier is good, see if you can see buildup, or a bent connector, or somesuch.
Also look at the usb plug on the cable, its uncommon but not unknown for the metal outer enclosure to open slightly, and make for a weak contact.
Sometimes a cable simply doesn't fit well for no obvious reason, , i have a generic cheap ebay cable that will only work when angled up or down, like yours, but looks perfectly fine, and feels to fit the socket, while the HTC cable works perfectly, so i know its not the port.
If it all looks good, then chances are you have a dodgy connection from the usb port to the mainboard, which will get worse every time you wiggle and bend the cable to get it to work. In this case, you COULD try a repair, but there have been reports on here of some repair shops pronouncing it too fiddly to replace teh usb port, and a new mainboard would be the only other option.
edit - just reread your post and seen that you can wiggle the port. Broken solder, gotta be. Its not an easy solder, so if your a dab hand, then go for it, if not, see above.
Hi iainbp, heresandyboy had this same trouble in http://forum.xda-developers.com/showthread.php?t=903977 from post 16.
It looks tricky!
Just a thought though, I recently bought a cheap phone charger with multiple interchangeable heads for different phones. The microUSB one became difficult to charge with and it took me a while to realise that the metal bit at the end had detached from its plastic casing, and when I plugged it into the phone it just got pushed back into the casing. (got my money back)
Possible with yours?
Occasionally since I got the phoone I've noticed that the audiobooks I've listened to have suddenly stopped, and prompting me to press play again; it always seemed to happen when I had a hand in my pocket, so I probably just assumed I had touched the screen or something. It was annoying, but I just continued on.
Then late last week after it happened while I was at my desktop and just moving the phone, I investigated a bit more closely.
I found that I could wiggled the headphone USB dongle, and the fit was not as solid as you'd expect (of course, I hadn't really checked this earlier, just putting in and taking out USB connectors up to this point). As I wiggled it, the audio would stop as if my headphones were disconnected and reconnected. Which must've been what had happened before.
Then I checked with my charging cord. Same kind of fit, I could wiggle the connector a few degrees. Enough for me to raise some concern about it being a faulty USB port, or it having somehow gotten loose in the shell.
This is probably RMA worthy, I'm guessing. The question is what will OP do? Replace the whole phone? Repair it (repair what exactly, I'm wondering)? I've not dealt with their support before, and I couldn't really find any suitable thing under their repair service categories.
Could some people check how snug their USB connector fit is and report back to me, so I could find out if this isn't how it's supposed to be?
First check your USB port for lint. I typically use a needle to clean mine out (Don't short any of the pins if using a metal needle). Lint will prevent the cable from fully seating and cause it to feel loose.
OhioYJ said:
First check your USB port for lint. I typically use a needle to clean mine out (Don't short any of the pins if using a metal needle). Lint will prevent the cable from fully seating and cause it to feel loose.
Click to expand...
Click to collapse
The USB port is totally clean. Couldn't even spot any dust particles under a bright light.
I know the 3.5mm headphone jack isn't technically rated for as many cycles as a USB C connector but I still feel it held up to abuse like being in a pocket better than any type of USB connector.