Hey there guys,
I got a problem, obviously
I have an Emtac III GPS unit: http://www.emtac.com/products/bluetooth/datasheet_btgpsiii.html
When I try to bond it, I get a yellow Q-mark. I get that even Before I try to add the password.
Secondly, Emtac does NOT have password, i.e. most BT devices have "0000" but this one hasnt got one.
In wm5.0 you HAVE to add a password in order to be able to click "Next" when adding a device. So I tried 0000, and also 0183 (which I got from a vendor).
None of them works, so my GPS device isnt bonded correctly and therefore I cant use it with Destinator GPS (like Tom Tom).
Does anyone know a fix/trick or anything that might help me??
NOTE: It worked great with my Magician before, no hassle there. So the GPS unit is fine.
[/img]
Not much I can add, only that the vendor passkey is the right one, as stated in the manual. Good luck. In most cases where a pairing process is not working the device driver is at fault, in other words not the right one for the device. Maybe a Win Mobile 5 issue, wrong driver (since it was working on your previous device). Suggest you check if you have the latest driver. Good luck.
Hi,
I'm also having the same problem with my Emtac III and my Jamin.
Again, it worked a treat with my old XDA2.
How did you go?
Did you find a fix?
Cheers,
Dev
Hi,
I have an i-Blue GPS and when I first bonded it, it had the same Question Mark as you. I then had to set up a new outgoing com port (next tab over) and then select the GPS device and pick a com port that was available - Com6 in my case.
I then edited my navigator.cfg file to force it to pick up Com6 as I couldn't pick it up from the list within navigator.
Have you gone through the steps of adding an outgoing port? This is a necessary step.
Hope it helps.
Craig.
Thanks Cags.
No I haven't set up an outgoing port, so I'll give it a whirl.
Destinator PN is the same as it only allows a certain number of comm ports to choose from.
Any got any ideas what file on Destinator PN I need to edit?
Cheers,
Deva
Hey thedeva,
I don't have any experience with Destinator sorry and I only had to change my cfg file because the options within Navigator wouldn't allow me to choose a com port that was allowable by the phone - I only had com 5 or 6. Maybe the port that your phone allows you to pick will be permitted in Destinator.
Sorry that doesn't help too much.
Craig.
montana said:
Hey there guys,
I got a problem, obviously
I have an Emtac III GPS unit: http://www.emtac.com/products/bluetooth/datasheet_btgpsiii.html
When I try to bond it, I get a yellow Q-mark. I get that even Before I try to add the password.
Secondly, Emtac does NOT have password, i.e. most BT devices have "0000" but this one hasnt got one.
In wm5.0 you HAVE to add a password in order to be able to click "Next" when adding a device. So I tried 0000, and also 0183 (which I got from a vendor).
None of them works, so my GPS device isnt bonded correctly and therefore I cant use it with Destinator GPS (like Tom Tom).
Does anyone know a fix/trick or anything that might help me??
NOTE: It worked great with my Magician before, no hassle there. So the GPS unit is fine.
[/img]
Click to expand...
Click to collapse
Set up a NEW OUTGOING COM PORT on com ports tab (in bluetooth settings) - COM6 with secure connection - Open Destinator and go to gps settings and either hit find gps either put COM6 - 57600 - NMEA manually and it should work fine.
IF YOU USE DESTINATOR 6 (NEWER THAN PN) AND YOU HAVE SWICHED EMTAC GPS FROM NMEA MODE TO SIRF WITH CRUX VIEW IT WILL NOT WORK. SWICH IT BACK AGAIN TO NMEA MODE AND IT WILL WORK FINE.
Hope this one will help you out.
Cheers.
Lucas0511 said:
Not much I can add, only that the vendor passkey is the right one, as stated in the manual. Good luck. In most cases where a pairing process is not working the device driver is at fault, in other words not the right one for the device. Maybe a Win Mobile 5 issue, wrong driver (since it was working on your previous device). Suggest you check if you have the latest driver. Good luck.
Click to expand...
Click to collapse
Gps don't have password on device such as HP but on qtek (HTC) yes
the Emtac PW is different than other Gps (usually oooo )
Emtac PW is : 0183
try this you will see it work
TomTom and BT GPS
I believe TomTom requires the name of the GPS to end in "GPS"... try renaming it - or deleting and re-doing the partnership.
Charlie Grillo
Related
considering getting tomtom5 for my mda compact.
anyone know whether its compatible, has anyone got it?
Should be. TomTom 3 and 4 worked fine.
By the way, Bakonl's release of TomTom 5 was just posted on alt.binaries.warez.pocketpc.gps, along with a few maps.
Benelux map only.. :x
TT5 does work
and not only benlux maps are posted. italy, france, germany, spain, uk are posted as well. rest will be posted as well i guess.
anyway, waiting for my legal TT5 to arrive (with the bt gps), woei =)
I can't get it working... I tried installing in the program files and in the storage card directories but it crashes at the end of the tutorial, just after that the "Welcome to TomTom Navigator" message appears in the map screen.
I can't see the map nor the GPS is able to connect (TomTom "3" Navigator Wireless).
I can't find any registry entry, I modified the currentmap.dat in order to point to /storage card/italia-map.
Anyone was able to reproduce my problem and to solve it?
Yeah, I noticed there are a few maps out. I'd like Scandinavia tho Seems like a buggy version too.. Crashes often.
Yeah... reeeeally buggy, I tried to check the post in the alt.warez.pocketpc.gps newsgroup for infos about bugs/problems etc. but I can't find it in my nssp server and using the web I'm not able to see the post (I can just see the header) so... I still can't use it :lol: ; maybe it could be a bad installer, I noticed that sometimes it won't install some cabs from the cd, or maybe it's just the italian map which is corrupt... who knows? 8)
I guess the release on alt.binaries is a preview or beta version.
The official release of Tomtom 5 will be end of June.
Im still waiting for Destinator PN on emule...
Where can i find the TomTom 5?
I have installed TomTom 5 to see if it works, I'm unable to connect my BlueTooth GPS (Holux GPSlim 236). The port does not show up on the device list under Buzz WM2005.
Does anybody know how to change this?
Ikkuh
I have installed TomTom 5 , I'm able to connect my BlueTooth GPS (Holux GPSlim 236) on port 4
work OK for me !!!
JesperR said:
Where can i find the TomTom 5?
Click to expand...
Click to collapse
www.tomtom.com
Stefan
bruxelles5 said:
I have installed TomTom 5 , I'm able to connect my BlueTooth GPS (Holux GPSlim 236) on port 4
work OK for me !!!
Click to expand...
Click to collapse
I had the same problem.... go to the bluetooth com ports, change the GSM to use COM8.
Then start -> settings -> gps, on the first tab set com4 and on the second tab tom com8. The thrid tab should have the checkbox set.
Now reset your device.
Start tomtom, goto your GSM setup, choose Other bluetooth, select COM4.
Now exit tomtom and reset your device.
Start tomtom and wait a while (can take a few minutes for it to find the GPS).
This worked for me (you need the resets in order to detect the com ports!!)
Ikkuh
@Ikkuh,
How can I change the Com port settings on my MDA Compact? I can't seem to understand you're solution. I need Com 8 and TT5 only has 2,4,5 and 9.
Thanks in advance!
dickr43 said:
@Ikkuh,
How can I change the Com port settings on my MDA Compact? I can't seem to understand you're solution. I need Com 8 and TT5 only has 2,4,5 and 9.
Thanks in advance!
Click to expand...
Click to collapse
There is a serial port multiplexer build in just for the GPS. It is under settings -> GPS, if you use this, you can create a virtual serial port, and attach it to the hardware GPS. If you do this and reset the device, the virtual GPS will show up in TomTom (in my case it did ;-) )
Ikkuh
I must admit dickr43 has got a point. Even though you are trying to be helpful, Ikkuh, it's a bit hard to understand.
Start tomtom, goto your GSM setup, choose Other bluetooth, select COM4.
Click to expand...
Click to collapse
There IS no GSM setup in TT. Most likely you mean GPS?
There is a serial port multiplexer build in just for the GPS. It is under settings -> GPS, if you use this, you can create a virtual serial port
Click to expand...
Click to collapse
Doesn't exist either. Must be some third party app you have installed...
dickr43,
Try removing your GPS pairing from the Magician. Go select the 'Bluetooth Setting' icon under Settings/System and make sure both the serial ports are activated. Note which COM port is 'Outbound', then re-pair with your GPS device. Start TT and in the GPS settings panel, you should get things running by selecting the COM port that was marked for Outbound.
Unless you are running some third party software with virtual BT COM ports, that should get you up and running. If you are, try each COM port one by one. Don't hurry through the ports, but give it time to connect. 5-10 seconds at least. Also make absolutely sure your GPS is within range and has a satellite fix, or you are wasting your time.
I cant use tomtom 5 as a route map
I just want to use it sometimes without the gps module is it possible. Because with the older version it was possible to select a GPS simulator.
THX :lol:
The "unofficial" versions of TomTom5 doing the rounds seem to have been taken from beta builds. I installed without any problems, but noticed a number of bugs (not recognising GPS, the program freezing, picking up wild GPS info, settings not sticking)... sometimes you'd think it was working, and you'd think you'd got it stable, but then they'd fall down.
I've tried 3 different versions doing the rounds right now and none of them are stable. I'll wait a month or so for a more finished release is available.
i got my hands on TT5 aswell, the program looks realy nice and lot improvement to TT3, but as mentioned above, it's not very stable, spontain exiting of TT5 is not cool when youre in the middle of no where.
my gps was recognized directley,
i just went to BT settings and checked Com5 and a messege apeared that i must bond with a compatible device, so i bonded with my GPS reciever and in the TT wizard i could chose Com5 and it connected right away, much easyer than TT3
regards.
Hi,
I am considering getting TOMTOM5 for my T-Mobile MDA Compact and would like to use this in my car. Does anyone know or can provide screen shots of what the display looks like? Is it easily readable while driving?
Thanks
Msuk
I am trying to set up tomtom 5.21 with my BTGPS74 receiver but cant get the two to communicate. I know there is some settings you can change in settings/system/gps but the problem I have is I dont have the gps option in settings anywhere. Am I missing something? Does any on know what I should do. Tomtom wants me to use port 3 or 7 but when I try to set them in bluetooth settings it says its not possible check your settings. Any suggestions would b welcome. Thanks.
P.S I know the receiver works as it still works well with my N70.
...you should've gotten a GPS icon if software GPS recognized.
In rgister you can force simulation.
hklm\controlpanel\gps]
delete redirect and add 'group' with dword=2
Then GPS icon will appear.
I gave it programport 7,hardware 6, baudrate=57600
gps auto checked
I'm not sure about the settings...
I had to create incomming and outgoing com ports on my 3100 (not sure if you need both)??
TomTom used com port 9 and works like a dream
as soon as you start the programme it connects automatically as long as my receiver is on.
It even connects when the BT on the 3100 is turned off - it starts the BT automaticlally when tomtom runs!
Yeah i agree all you need to do is set up the com ports, then fire up tomtom and select the com port you just set up and away it goes
Chris
Thanks for the replies guys. I know I have to set the com ports but the problem I have is there is nowhere for me to do this. For some reason the gps settings is missing from the system/settings. I am going to try to reinstall tomtom to see if it helps. Tomtom has ports 3 and 7 showing but they seem to be taken by something else so I cant configure my receiver on either of them.
I have a slightly different problem... my TyTn can connect to the BT GPS reciever, but as soon as TomTom tries to calculate a route, or I click the GPS signal icon it crashes back to the Today screen...
I've got TomTom installed with 5.21 update, anyone had any problems like this?
you just need to pair your bluetooth device go to settings connections and bluetooth and add new device, let your tytn search and it will find a new device when you have paired it select new comm port outgoing
I have no gps setting in control panel either
Cheers
Chris
Hi,
i have a strange problem with my BT. I cant create a incoming or outgoing BT port. I dont know why but it wont let me create any ports.
Anyone with the same odd problem?
I had a similar problem, Tytn would only let me choose COM0 (Zero) as outgoing port, and TT works fine with it. However, I would like to add Mapking for Asia, and this navi soft will not accept a GPS on COM0. Anybody understands why Tytn is only offering COM0 as outgoing ports for GPS?
I have set the com4 as outgoing port and now tomtom seems to work fine.
thanks for that info.
I don't know why only port 0 and all other ports are blocked but TT works for me now. I only need to wait for a better ROM and i can leave my Wizard home
I have written to a good contact at HTC since I need COM ports other than 0 for Asian Mapking navi soft (in add. to TT) . Will keep you posted.
Answer from HTC:
"As my testing, the Outgoing port is not limited with COM0. PaPaGo can accept with COM0, COM2, COM4, COM8, and COM9. I think the limitation of COM0 is the software limitation of TOMTOM, So if the user wants to use Mapking that only support COM1~7, he need delete the outgoing port COM0, and reassign another COM port for the BT GPS."
I imagine the problem lies between the Tytn and TomTom only, and other navi soft would find other COM ports. But I am kind of hesitant to interfere with a working TomTom, and go through the outgoing COM port game again...
I'm using Navigon and set up an outgoing Connection on com2 and it works fine for me.
sounds like TT is the problem ...
greetz
sphings
Guys, let me try to help you a little bit, as I work in navigation software development (Destinator).
1. The COM ports has nothing to do with the actual software you are running. This is pre-defined in the ROM you are using. That is also the reason why we see variations here - we use different ROMs.
2. In order of enabling a COM port, you do NOT need to discover the GPS icon on the settings. It is quite useless unless you wish to work simultaniusly with more than one software.
3. To enable a COM port, after you pair the GPS, look down for the tab COM Ports in the BT settings Manager. You only need to create Outgoing COM.
4. Strange but usually you will only be able to choose between 2 COM ports. The rest are hidden by the OS. MAKE SURE that you disabled the "Secure Connections". Default key for all the GPS receivers is "0000" and for Globalsat 308 is "2003". The last is AKA HP GPS.
5. If you cannot enable any other COM port than COM0, this is a ROM problem and you should contact your ROM provider like the mobile carrier. You can also try to enable other COM ports with the attached CAB file. Simply run it, it will expose all COM ports for you and now you should start trying. I reccomend to test COMs 4-8 first, normally, it will solve your problems. (Note: I got this file previously here and did not create it myself).
There have been may posts about TomTom not recognising B GPS's.
One solution that doesnlt seem to be mentioned here id to ensure that the name of the GPs in BT connections actually ends in "GPS"..
If it doesn;t renove the pairing and re-pari , but change the name this time to something that ends in "GPS"...
good luck
Charlie Grillo
Thanks guys, found another solution that works for me now:
1) Set your Bluetooth GPS to another COM port than 0 (TomTom´s standard port 6 was not available, so I choose 2)
2) open Programs/Navigator/navigator.cfg with a text editor, change COM0 to COM2
3) start TomTom - working on COM 2!
Started Mapking, found COM 2 - working now.
hello fellas,
as you can see im new here. im thinking of buying the TYTN, a sector which i have never explored before (pda sector).
it sounds great with the applications and due to my work, a need for a pda is becoming bigger.
i posted in this message due to the GPS topic.
i got a very stupid question which you may recieve occasionally if i buy the tytn.. :twisted:
why do a person need BT enabled GPS? i read you can connect it to your PDA but for what reason?
thanks in advance and apologies for any inconvience..
@D_G - welcome to this board
In order to run navigation software on your Tytn you need a external GPS connected to it. Easiest solution is a external GPS connected via Bluetooth.
Another solution would be to buy a PDA phone with a GPS receiver on board, for example the ETen G500.
Of course we would all be interested in a UMTS PDA with integrated GPS, with acceptable battery life, but that will take some time...
thanks lucas for the answer. but why would you need a navigation software if you have a GPS device? in either case you will need to have both devices in a particula blue tooth range. right?
this means you will need your handheld device + the GPS to activate the navigation software, or dd I miss something?!
Hi Good Peoples,
My first post here and I hope you will excuse my ignorance please. I am hoping that someone can help me, as I would pull my hair out, if I had the left. :shock:
I have an XDA 11s and I have installed TomTom software. The satellite receiver is a Haicom HI-701 BT (four in one Bluetooth) and I have a number of problems.
When I installed the GPS hardware, in the Bluetooth Services section I installed it as a serial port connection and have the enable service box ticked. Do I need any other boxes here ticked?
The Bluetooth Manager shows the Haicom shortcuts, but it does not connect on start-up. It has to be manually connected. Once it is connected, unfortunately it shows no dataflow, in either direction. I think that is the second problem. :roll:
The Bluetooth flashing light shows that the Bluetooth connection has not been made; what do I need to do to fix that?
When I start the TomTom, it shows that I have no GPS Device (now there is a surprise) and I tried to configure it using the NMEA option with 4800 baud rate. However I then have eight options ranging from infrared through to Bluetooth serial to choose from, and I'm not sure which one I should be using. I mucked around for hours and had working for about one minute, but unfortunately I can not repeat the trick.
Is there anyone out there who could be kind enough to please tell me how to configure the thing please?
XDA IIs
The XDAIIs is a BlueAngel - try posting in the correct forum next time.
Make sure that you have selected the "outgoing connection" - not the "incoming connection" when choosing the serial port in TT.
Also turn on BT and manually connect to the GPS first - somethimes I had to do that rather than rely on TT to do it for me.
You asked whether other boxes sould be ticked - what are these - I no longer have a BA and can't remember...
Charlie Grillo
oops sorry, I was not sure which forum to post it under as the BlueAngel did not specify IIs, although the picture looked like a better match.
I hate to sound like a total technical cretin but what is TT?
The other boxes are:
Authorisation requires
Authentication (Passkey) Required
Encryption required.
Thanks for the response.
TT = TomTom
I have found a fix for my XDA2 with Tom Tom and GPS BT-321 H
This was such a headache for me but through persistance - I got it working
This is how I did it
1. I downloaded - Bluetooth tool 1100 "BTHTools1100"
this help me to asisgn my Holox BT-321 to my XDA2 via bluetooth to port Com7
2. I then downloaded "GPSTuner_v5" & GPSmonitor1.1
These programes enable me to talk to my GPS and adjust PORT COM setting and also Band rate
having got these programes to work and pair with my GPS
the next step with TOM TOM6 worked fine trying different ports
All the Best to all XDA fans out there!!!
I have found a fix for my XDA2 with Tom Tom and GPS BT-321 H
This was such a headache for me but through persistance - I got it working
This is how I did it
1. I downloaded - Bluetooth tool 1100 "BTHTools1100"
this help me to asisgn my Holox BT-321 to my XDA2 via bluetooth to port Com7
2. I then downloaded "GPSTuner_v5" & GPSmonitor1.1
These programes enable me to talk to my GPS and adjust PORT COM setting and also Band rate
having got these programes to work and pair with my GPS
the next step with TOM TOM6 worked fine trying different ports
All the Best to all XDA fans out there!!!
Thanks, I have actually got it working with a combination of black magic, voodoo, good luck and threatening to trample on it. :wink:
Got my htc tytn loaded totom 5 onto it and guess what bluetooth gps doesn't work with it! Cannot get correct comm port .According to HTC TomTom know about this. Just hoping somebody already has a fix for this?
Had no problems pairing my BT Slim GPS with my Vario II, TomTom runs fine.
What GPS receiver you using ?
works fine on my xda trion as well.......im using tom tom 5.21 with BT-338 gps receiver.......im also using com port 0......you basically have to pair it and then add outgoing port as com port 0.....and during the installation on tom tom make sure you choose com port 0......that worked for me anyways....hope that helps.
Bluetooth GPS HTC TYTN
Thanks guys have re-installed tomtom and now it comes up with com prt 0.Probably didn't install correctly first time .Now up and running .Fantastic!!!!
I could cry
Hi everyone - I am having a similar problem
I have a new GPS receiver and have established a bluetooth partnership and done the outgoing port to com0 which is the default.
Tom Tom is installed and when I try and configure it I am not seeing all the options shown on the website. It just says no gps detected or something similar. I am sure its something simple.
Can anyone help please?
mobilecat said:
Hi everyone - I am having a similar problem
I have a new GPS receiver and have established a bluetooth partnership and done the outgoing port to com0 which is the default.
Tom Tom is installed and when I try and configure it I am not seeing all the options shown on the website. It just says no gps detected or something similar. I am sure its something simple.
Can anyone help please?
Click to expand...
Click to collapse
There's a program CreatePorts that is floating around (you'll have to do a search) that allows TomTom to see additional com ports in the Bluetooth GPS setup. I used this same program on my Samsung i730, and now on the 8525.
You just paid your GPS with the PPC, create the outbound port (in my case I used com 2), run CreatePorts, and then go in to TomTom GPS setup.
Once you get it set up, you don't have to run the app anymore, and TomTom works great
OUCH
dew.man said:
There's a program CreatePorts that is floating around (you'll have to do a search) that allows TomTom to see additional com ports in the Bluetooth GPS setup. I used this same program on my Samsung i730, and now on the 8525.
You just paid your GPS with the PPC, create the outbound port (in my case I used com 2), run CreatePorts, and then go in to TomTom GPS setup.
Once you get it set up, you don't have to run the app anymore, and TomTom works great
Click to expand...
Click to collapse
I tried running this but i can still only assign certain points from my bluetooth manager and dont have these displayed on the tomtom menu.
When you go into the GPS Status settings on Tomtom and tap configure, have you tried looking to see which com ports it lists and then going back to the bluetooth settings and doing trial and error to allocate any of those port numbers as an outgoing port for your GPS unit?
For my genuine Tomtom GPS unit, I did not even have to set up a port, I just had to pair the device but when I used a friends alternative brand of GPS unit for a short while, I was only able to get that one working under Com port 4. I can't quite remember but it may even have been a case that Com 4 only became visible in the Tomtom GPS configure menu after I had allocated it as an outgoing port for the GPS device (sorry, it is a while back so I can't quite remember the order in which I set it up)
Hope you get it sorted
arghh
I a so annoyed. I did this and had no luck. Later on I did something and got the option for port 2 and used it and it was great. I had to do a soft reset for something else and I cant do it again. tried everything.
MMMM
Happy yet frustrated
I have deleted create ports from my device as it only works once. I have reset my device. I reinstalled createports and extracted the file. I then saw port 2 straight away - the one that had been missing in tomtom.
The only problem is that if I do a soft reset I have to do that again!
It is very frustrating trying to get some of these things working. Have you thought about upgrading to Tomtom 6? you may find you have less problems getting the pairing and ports working right.
Failing that, I am sure you will be able to get it working again, just keep trying all the com ports one by one until you find one that appears in the Tomtom configuration. Like I said, on my XDA Vario II (Hermes) I managed to get it working on Com 4 and when I had an XDA Mini S (Wizard) I seem to remember that it was either Com 6 or Com 7 which worked on that one.
You might want to check the bluetooth settings for security and beam as well. Try turning security off (ie. passkey required off) and make sure the beam setting is ticked to receive all incoming beams.
I will keep my fingers crossed for you
download co-pilot for uk
Dashley said:
Got my htc tytn loaded totom 5 onto it and guess what bluetooth gps doesn't work with it! Cannot get correct comm port .According to HTC TomTom know about this. Just hoping somebody already has a fix for this?
Click to expand...
Click to collapse
Any one got the co-pilot softwear to insallate for MDA VARIO 2.
download co-pilot softwear for UK.
Any one got the co-pilot softwear to insallate for MDA VARIO 2.
another thread
I have just seen another thread about XDA with a patch for this that seems to work. Can someone merge the threads?
Createports
Can anyone point me in the right direction to find this program. I think that it is hidden on the web somewhere near the holy grail.
Help with TT6 + TYTN + Royaltek 2110 please
I have a TYTN and a GPS Royaltek 2110. I have position com0 and other programs GPS work correctly. The problem is that the TT6 always shows he himself message “GPS nonfound”, although always I can say to him that this in the COM0 but does not find satellite.
That I can do? I put the TT5
somebody it has the CreatePorts program and it can put it?
Thanks
try this thread:-
http://forum.xda-developers.com/showthread.php?t=288865
Pairing TOMTOM 6 with Bluetooth GPS
For all of you that are having problems pairing your GPS Bluetooth receiver with your Hermes see the instruction set below:
#Hermes can not be in flight Mode#
1st: Run BTHTools1100.exe
--------------------------------------------------------------------------------------------------
2nd:
Pair them in Bluetooth Manager
Set:
Holux (outgoing port com4)
Incoming Port (com8)
no security
------------------------------------------------
3rd:
In settings >> Connections >> GPS
Programs set GPS program port to Com 8
Hardware set GPS hardware port to Com 4
baud rate 4800
If GPS program is not seen in settings\Connections
Use resco registry or other program and:
Go to Hkey_local_Machine\ControlPanel\GPS settings\ creat (make new) "Group" with Dword data =2
---------------------------------------------------------------------------------------------------
In TomTom chose:
Bluetooth GPS
Com4
should be working Now
Pairing TOMTOM 6 with Bluetooth GPS (easy) - Kaiser
First after reading the posts I thought I had to reinstall Tom Tom or install another software. Luckily, I paused and read the message when I was about to configure my other bluetooth receiver. It said, first you must establish your bluetooth connection. Well, I lied coz I did try to go on and couldnt find COM 0 or whatever you guys have said.
But that's what I did, eventually. Paired the device as BT GPS, check the serial connection (not sure if secure connection needs to be checked but I left it unchecked to find out later). After that go to com port tab, and click add new port ie selected COM0.
Then go back to TT6 (restarted in my case), and to other bluetooth gps receiver then found COM 0 in there. Voila!!
Chose COM0, but still got no gps device message. Waited for about 2 mins while reading further into the posts and now my TT6 is working.
You could call that strike of luck I dont really care but yeah.. saving some batt power on my kaiser for the bank holiday;s trip. Have a great one everyone!!
P/s: Mine is O2 stellar on Dutty's great work.
Com 4 is the only one that works with Schaps 3.54
Dear Htc fellows,
My bluetooth GPS is working strange on my Universal, but on iPaq with
WM2003 works as a charm. The BT GPS is new Solar GPS with new Mediatek
chipset.
It's not working with iGo 2006 and even not Tomtom 5 or Tomtom 6.
I can find the BT GPS in BT manager, I can pair it, but I dont know why,
it needs a pass key even if it shouldn't. Then when I explore it's
services, The popup come again asking me if I will allow external BT
device to connect to my Universal and it come asking passkey again (Why?).
I can't even enter an empty passkey (bt device doesen't require it). After that I have successfully paired the device. I can add it's serial port to enumerate on com ports 8 or 4.
When I start Tomtom, it doesent detect the device at all. If I use iGo, it detects, gets datas and disappear, it's allways appeared for 1 second and then 5 seconds not. No matter Which bitrate I set (device is written to be 9600) it needs to be in NMEA protocol, not SIRF.
When I use some freeware GPS programs, it seams to be working ok, it shows satelites and it's not disappearing.
What can I do with that???
I have some idea that it's probably about WM5 and it's security....
How can I setup com security in registry? can I set the port speads manually atd... I had performed a hard reset and it still don't work. Can ROM update or AKU update help me?
Does anyone have some idea what should I try now?
O2 XDA EXEC:
Rom: 1.30.107
Radio:1.09.00
P:42.42.P8
BT GPS: model: BT 2.5MR
made by f-tech.com.tw
Thanks;
Shef
Could you find a solution??
Hi,
I have the same problem exactly and could not find anything on the net. Did you solve your problem?
well ...
i know that there is a problem with GPS and WM5 and so there is this patch which i install every time i hard reset .....
the guys i bought MY GPS from gave me this ... and they are pretty knowledgable .....
it works well ....
try it !
tried
My OS version is WM2003 but tried anyway.. Did not work.. can there be version for WM2003??
did you ?
did you define an outgoing com port for the device (com 4 for example ?)
com port definition
well, igo finds the device an COM 6 actually, it connects too.. but stays connected just for a second, then again and again..
I installed GPSGate and created a virtual com port 7. I manually configured the GPS receiver connection to COM 7 on igo.. But all the same.. :
do you advice another way?
one other thing the device works with navigon 5.0 and tomtom 6.0 smoothly, no problem.. only igo..
well...
IGO is CRAP ... that is well known .... lots of bugs ...
i am sorry .. i do not know how to solve your problem...
but i suggest using destinator 6 ..... (that's what i use) ....
simple ... nice looking .... big buttons and able to navigate to your contacts directly (especially useful if you have Phone Edition)
oh ... and ... works great !
I got the Holux GPSlim 236 GPS. I can pair the GPS with Universial. But I cannot set the com port at all. A pop up window always say the com port (I tried everyone of the ports) is not available.
Any one got a solution, does the GPS bug fix help ? and what does it fix ?
Might seem a bit obvious, but have you tried the code "0000" when pairing your device?
Once paired...did you define an outgoing serial port on "Bluetooth Settings" menu on your WinCE?
I have a royaltek bluetooth GPS and it's been working well with TomTom[5|6]...I use '0000' as passkey (default on many 'non-interactive' devices), once paired I clicked on 'COM Ports' tab and defined a new outgoing port, the wizard should list the GPS as an available device to create a COM port so I used it and I got a 'com0'.
Once the outgoing port was created I had to tell TomTom to use the new 'com0' and worked like a charm
It's been working since TomTom 5.21 (previous versions didn't work).