Wireless Network Settings for MDA Vario (T-Mobile Wizard) ?? - 8125, K-JAM, P4300, MDA Vario General

Hi all,
Could you please help how to set up wireless connection for the Wizard. I've tried myself but found it so complicated and entangled.
1. The internet connection works fine whenever I plug the Wizard to my laptop. Obviously it then connects to the Internet through my Laptop.
2. When the Wizard is off-hooked, it shows that it can detect my home wireless network and in the Wireless LAN section it shows that the connection is established. However, when I open Internet Explorer it usually starts with saying "Connecting to GPRS". Only when GPRS cannot get connected, because I don't use it, IE starts connecting to the wireless network and browsing.
So my questions are:
1. How can I configure the Wizard so that it can start connecting to my Wireless network without attempting the GPRS connection?
2. I find a list of many networks obviously set up as default by the supplier (T-Mobile) in the Configure Wireless Network section. How can I delete them so that Wizard shows only available networks? There's a "Add New" option, but I cannot find "Delete" anywhere.
3. In the Connections section, I find "T-Mobile Internet" and "My Work Network" settings. In Advance -> Network Management section, I find "Programs that automatically connect to the Internet should connect using:" then a list of networks. Can you please explain what this does and if I could add the settings of my home wireless network to this section.
Some Newbie questions, please don't mind if they seem silly. Your help is very much appreciated.
Rgds,
PPB

Related

XDAIIi Wifi Problem

I tried to use Wifi in a cafe, the wireless lan manager show connected to network, buy when i open IE, my PDA always trying to connect with GPRS service. the wifi seems not working, and i could not open a web page.
could some one tell me what should i do :idea:
try picking another network in
system connections connections advanted
pick something other then my isp or what ever the gprs connection is called
hi! thx for reply
i tried today in starbucks, but the GPRS seems still comes up, i picked up my work network, tap edit, there are only three option, 1, auto pick 2, O2 active
3, WAP network
when i open IE, it always inform me, connect to O2 active, then Dialed: Then answering modem has disconnected. To check your connection setting and change them if needed, tap setting.
the wifi connection is realy confuse me, dose any one know how to connect to internet in a cafe or airport??
When you've got wifi enabled make sure that Settings->Connections->Network Cards has My Network Card connects to "The Internet".

Connection settings: My Work Network vs. My ISP?

I'm confused about network settings in my Exec (but I guess this question applies to all WM devices).
What's the functional difference between My Work Network and My ISP? When I'm browsing WiFi networks and a new one is discovered, the notification says:
"Wireless Node 2" network connects me to:
O The Internet (or work via a VPN)
O Work
What's the correct answer? Why do I have a choice? In some cases I'll want the WiFi network to allow me to only access the Internet and in other cases (like the WiFi networks in my house) I want to be able to access the Internet AND browse files on other PCs + use Terminal Services. Should these situations require different settings or are they essentially the same?
Second question: If I'm using a program that needs an internet connection, what settings must I choose to ensure that the system uses WiFi if it can, and then GPRS only if WiFi isn't available? I've changed the option in Settings > Connections > Connections > Advanced > Select Networks so that both drop-down boxes show 'My Work Network' (since I don't want to choose a default of My ISP - i.e. GPRS - for network activity if a WiFi connection is available) but now I can't seem to find any GPRS connection options. How do you all connect to GPRS manually? If I tap the signal status icon at the top of the screen I have no 'Connect GPRS' option like I did on my XDA2.
I'm confused by it all. Thanks in advance for any help you can provide, especially links to pages with how-to guides for idiots
PS. Tried searching these forums, but the subject is too generic and there are hundreds of results.
Hi
In my opinion WM2003SE's handling of connections is horrible. I understand you, being confused.
I'll decribe WM2003SE way...
Your exec has WM2005, but as far as I know, the rules are similar.
The general difference between "Internet" and "Work" is that connection set as "internet" allows you to surf web and give your program access to internet. While connections set as "work" should be used only when you connect to your home/office network (and optionally internet).
About disappearing "Connect GPRS". It's pain in the ass really
You can create as many "connection profiles" as you want (like "My ISP" "My Work Network" "My other freakin' ISP" "Etc")
Then you add some connections to certain profile....
eg.: create gprs connection (named "O2 GPRS inet" for internet in "my ISP" profile.
That means that when you change default Internet profile to "My other freakin' ISP", you won't be able to use "O2 GPRS inet"...
Ok.. answering your first, main question.
If you want to use inet, browse shared folders and use Terminal Services you should edit "My work network" properties and check "This network connects me to the Internet".
When at home. Select (in settings->connections->connections) "My work network" for both auto internet and auto private network.
When roaming around, you should change auto inet to "My ISP" which will have a configured GPRS connection inside.
Your phone will use Wifi first (before GPRS) when activated and available.
OMG.. my fingers hurt.
Have fun fighting with WM
Thanks for your reply, robal. It's a big help but I'm still not 100% sure of the situation.
robal said:
The general difference between "Internet" and "Work" is that connection set as "internet" allows you to surf web and give your program access to internet. While connections set as "work" should be used only when you connect to your home/office network (and optionally internet).
Click to expand...
Click to collapse
But I want both types to connect to the Internet. I still don't really see the difference. Does My Work Network apply to connections for which a VPN is necessary? If I choose 'The Internet' as the option when connecting to a new WiFi network, will that change any aspect of the way in which the connection works? Perhaps I should just try it and see. Trouble is, if I screw it up I'll never be able to get it working again!
robal said:
If you want to use inet, browse shared folders and use Terminal Services you should edit "My work network" properties and check "This network connects me to the Internet".
When at home. Select (in settings->connections->connections) "My work network" for both auto internet and auto private network.
When roaming around, you should change auto inet to "My ISP" which will have a configured GPRS connection inside.
Click to expand...
Click to collapse
Perhaps I'm expecting the impossible. I want to set it up and forget about it, so that wherever I am my device can access the Internet. If I'm connected to a WiFi network then that's the connection but if not then it dials up GPRS automatically when a program demands a connection.
Does everybody else use robal's method and change the settings depending on the availability of a friendly WiFi access point?
If this is the case then Windows Mobile has a long way to go before the connectivity is seamless...
I was largely having probs connecting to 02's 3G network as I couldn't find the settings.. now I kind of understand. Kind of.
--O2 Contract 3G settings--
Name of connection: O2 Internet
Select a modem: Cellular Line (GPRS, 3G)
Access Point Name: mobile.02.co.uk
Username: mobileweb
password: *** (it was prefilled for me..)
Advanced Button should be set to auto-assign IPs
--
With regards the original post, I have mine setup so that if I connect to my local WiFi, then I get the internet through that. If I disconnect, or not in range, etc, then it will use the 3G settings.
I'm still a little in the dark with regards WM5.0s handling of network connections, but here's what I think is right:
Start > Settings > Connections Tab > Connections
[Tasks Tab]
You can only have *2* active connections
You can have multiple profiles under each connection.
So, I renamed my O2 Internet connection to something other than "My ISP", I chose "O2 3G Network" to make things a tiny bit less confusing. (This is the network with your 3G settings in as above.)
The second option I renamed to "My Wireless Network", and as far as I can tell, you do not need to change anything in there - unless you want to add VPN information.
[Advanced Tab]
Click "Select Networks"
Here you can choose between your 2 active connections. For the top option I chose "O2 3G Network", the second option "My Wireless Network".
Click OK
--
Now you have two networks setup. Open Internet Explorer..
If you do not have WiFi switched on, it should automagically dial your "O2 3G Network" when you start browsing.
If you're at home, or near a WiFi network, switch it on by holding your stylus on the "U" in the taskbar. This should give you the option to switch on WiFi.
A few handshakes later (this took about 2-3 mins to actually connect to my WiFi) and your "U" should change to the WiFi antenna icon.
*Check you have fully connected to WiFi before browsing!*
Do this by again, holding the stylus on the antenna icon and checking that your WiFi name is displayed, along with the signal strength.
*If you try to browse the web before your WiFi is ready, it will just attempt to dial O2 3G Network!* - Patience is required...
So, whether this answers the original post or not, I mean, it isn't exactly Automatic, but I guess if you leave WiFi switched on, then in theory it will use it, else it will dial your 3G network.
Well, thats my brain dump for my own benefit, hope it helps out others.
That will be very helpful, thanks gaspx. I'll try your suggestions later on and let you know how I get on.
So with those settings when your Exec finds a new wireless network and invites you to set up your connection, which do you choose? "The Internet" or "Work"? I think :?: that those two options are independent of your renaming of "My ISP" to "O2 3G Network"...
I guess I can get it set up right like you have, but I hate not understanding this. It should be so simple but it's not!
"The Internet" or "Work"? I think that those two options are independent of your renaming of "My ISP" to "O2 3G Network"...
Click to expand...
Click to collapse
Yes, they are independant and are accessible when you choose Start > Settings > Connections Tab > Network Cards
Then select Network Adaptors tab.
What I'm not fully understanding is how these two options differ(!):
For instance, I have a static IP address on my WiFi, so I choose Network Adaptor Profile "Work", then configure "tiacxwin Compatible Wireless Ethernet" and enter in my static IP and DNS etc..
What I would *expect* to be able to do is choose between "Work" profile and have my static IP, or "The Internet" profile, and have dynamic IP.
But it doesn't appear to work that way.. if I add static IP address, it uses it for both Work and The Internet. Confused ? Me too.
which do you choose? "The Internet" or "Work"?
Click to expand...
Click to collapse
So from my initial playing around, it doesn't appear to make any difference! - Otherwise i'd expect to add a roaming WiFi Hotspot to "The Internet" (and dynamic IP) and any Work related (static IP) to "Work".
Must be missing something fundamental here, but O2 Exec manual (pg.92) isn't especially forthcoming with an answer.. :?
This might help you a bit.
I connect to work with a vpn connection over the internet. the address for the vpn is a url.
1. I set up a gprs connection under internet
2. I set up a vpn connection under work to vpndomain.com.au
3. in the advanced tab of connections I add *.vpndomain.com.au to the exceptions list for work connections
4. I start a terminal session to terminal.vpndomain.com.au
the device connects to internet then connects to work over internet.
if you don't need one connection to occur via another then make them all internet
hope that helps
Okay, a bit more braindumping to understand the differences between "Work" and "The Internet" courtesy of ActiveSync Help..
ActiveSync > File > Connection Settings
This computer is connected to: Auto/Work/The Internet
---
Use ActiveSync to "pass through" this computer. That means the connected device can use the computer's network connection as if it were its own. You can use this feature to perform tasks such as downloading non-Outlook e-mail messages, to connect directly with Exchange Server, or to browse the Internet.
---
So, from that, I set the connection type to "The Internet" in ActiveSync, and I was able to browse the internet on my XDA.
I then set the connection type to "Work Network" in ActiveSync and was *not* able to use the internet.
What does it all mean ?
Well, at the moment all I can think of is that if don't set it to "The Internet", you er, don't get Internet access. :roll:
Applying that to the original question of which do I choose:
"Wireless Node 2" network connects me to:
O The Internet (or work via a VPN)
O Work
Click to expand...
Click to collapse
I would holeheartedly recommend (if its a wireless network you've found whilst walking the streets) that you choose "The Internet" !!
--
Functional Differences
I'm thinking/believing/speculating that the functional difference between the two is that the "Work" option is for connecting to local or internal IP's only, for instance anything on your 10.x.x IP range if that is the subnet you're on.
The "Internet" option allows any *external* IP address to be accessed, and no access to the local IP range. This would then require the VPN option to be used to access local/intranet resources. (This is the passthrough option as mentioned above in the ActiveSync help)
I'm literally typing as i'm testing, and so far it kinda makes more sense to me now.. kinda.

Wifi connection for UK T-mobile Vario

Dear all,
I'a a newbee and i've been trying to connect to my home wireless network but I can't. I go to the "Configure wireless networks" and find a list of network adapter. I guest the one i need to config is "SDIO Wlan wireless adapter". I have played around with it, with or without IP address but it doens't work. I select "My work network" under "programs that automatically connect to the Internet should connect using" but it doesn't work. Could someone help me out please?
Cheers
try 64 bit encryption
I couldn't connect to my work or home networks with my Vario. it turned out 128 bit encryption was not playing. once I set the access key to 64 bit it connected no bother.
no encription option
Hi,
When I set up a new wireless network, i put name, then choose "connect to the internet" in the "general" tap. In the "network key" tab, i choose "open" under authentication and "disabled" in data-encryption field (the other choice is WEP) because i don't set any password for my home WIFI.
Could someone help me, please?
Normally the my device should pick up the signal automatically. in the "configure wireless networks" window i find a list of many networks in the "wireless" tab, including the one i set up, but none of them connects to my home wireless network.
HELP! HELP! HELP!
thanks

Connections - Some Help Required

Guys,
I'm hoping somebody with some time can just help me out here. My Touch HD is on Vodafone (UK) and I have some issues with connectivity.
I have a home wireless network, along with "Contract Internet" provided by Vodafone. If I start by telling you what I'm after. I basically want all my applications to use my "Contract Internet" network (GPRS/EDGE/HSDPA) by default, providing that there is NO active Wifi connection or USB connection. If there is, it is to use that.
Now the problem I have is that the only way I could ensure that my device connected to a) my home resources and shares (pc's and printers) and b) connect through my wireless router for gateway access to the internet (without the net attempting to launch GPRS connection) was to set both "Programs that automatically connect to the internet....." and "Programs that connect to a private network...." connection networks (Start, Settings, Connections, Networks, Network Management) to display "My Work Network" - this seems to allow that....however, when not connected to wifi, the GPRS or Contract Internet connection launches fine, but doesn't allow access to lots of applications which normally would utilise the network....only the internet works. Windows Live, RDP, you name it.....it doesn't work....unless I switch back the "Programs that automatically connect to the internet....." connection to "Contract Internet"
Ideas...help...please!
Cheers in advance
**bump** Please - at my wits end!

Connection Probs - PLEASE HELP!

Guys,
I'm hoping somebody with some time can just help me out here. My Touch HD is on Vodafone (UK) and I have some issues with connectivity.
I have a home wireless network, along with "Contract Internet" provided by Vodafone. If I start by telling you what I'm after. I basically want all my applications to use my "Contract Internet" network (GPRS/EDGE/HSDPA) by default, providing that there is NO active Wifi connection or USB connection. If there is, it is to use that.
Now the problem I have is that the only way I could ensure that my device connected to a) my home resources and shares (pc's and printers) and b) connect through my wireless router for gateway access to the internet (without the net attempting to launch GPRS connection) was to set both "Programs that automatically connect to the internet....." and "Programs that connect to a private network...." connection networks (Start, Settings, Connections, Networks, Network Management) to display "My Work Network" - this seems to allow that....however, when not connected to wifi, the GPRS or Contract Internet connection launches fine, but doesn't allow access to lots of applications which normally would utilise the network....only the internet works. Windows Live, RDP, you name it.....it doesn't work....unless I switch back the "Programs that automatically connect to the internet....." connection to "Contract Internet"
Ideas...help...please!
Cheers in advance

Categories

Resources