Database Users

1.12.00 WWE ROM, Bluetooth COM Port settings, ActiveSync

Hi all,
I've just recently upgraded to the above ROM- everything else seems to be fine but I've just realised that the 'Settings' for BT are slightly different to my original rom version.
I can pair the JAM fine with the PC but it won't let me connect. As I look at the BT settings, I can see the following tabs: Mode, Devices and COM Ports; it's the COM ports that has changed. It's got New Outgoing Port and New Incoming Port. When i select either of these I can't assign any port number; the drop down list is blank.
P.S. I was able to connect fine via BT using my original ROM v1.00 or something.
Any help appreciated.
Thanks.

hey man
i just posted another querry regarding the card reader ...
hope u read it !!
getting back to yr problem
follow the instructions on this link and yr problem will be solved (HOPEFULLY)
http://howardforums.com/showthread.php?t=544932

I remember reading that link a while ago but I got the BT working without Pocket Tools software...
Anyway, I've tried both versions from the website but after installing either of them, the connect via bluetooth in Tools of ActiveSync is not there; just the IR. As soon as I uninstall the software it's back there.
I thought I had mastered the myth of Jam and Bluetooth- looks like back to square one!

Sorry - I'm just impatient- reinstalled and re-paired a few times and all is fine now.
Thanks for your help.

reinstalled what may i ask? im having this exact problem at the mo

Instructions from the top of my head (excuse any errors)
1) I removed the Pocket Bluetooth tools from remove programs
2) Perform soft reset and remove any existing paired devices
3) Reinstall the Bluetooth Tools (i used the an earlier version)
4) Select ActiveSync check box
5) The device should be paired
6) Go to to ActiveSync on PPC; go to tools and you should see Connect BT with ***
This should work.

Strange issues during ActiveSync'ing

When I ActiveSync, I notice my laptop shows that it is trying to make a network connection...then stops trying. A minute later, my K-Jam says it was unable to make a network connection. The strange part is that I haven't setup anything to make a network connection. Any thoughts?
Thanks,
Tom

Upgrade to 4.1
I read somewhere that the Wizard does not sync properly witch any ActiveSync versions before 4.1 (which is not officially out yet).
Check here for info and download: http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=375

activesync 4.x does use ip addresses, if you check this link and then the link in it, you will get some answeres & hopefully all your problems will be solved.
http://forum.xda-developers.com/viewtopic.php?t=32022

I'll check out the link....thanks!!! I have 4.1 installed since I got my K-Jam. I rarely ever used it with my PDA2K, but I have to install programs...damn those exe's...why can't everyone just use CAB files.
Thanks,
Tom

situation that can arise with cab files is they self destruct/delete after the install is completed,
unless you change the attributes to read only

aliendad said:
situation that can arise with cab files is they self destruct/delete after the install is completed,
unless you change the attributes to read only
Click to expand...
Click to collapse
Not if you use CabInstall

Softick Card Export II version 2.11! Now working on Wizard!

read more: http://www.softick.com/news.html#83

Re: Softick Card Export II version 2.11! Now working on Wiza
dddrko said:
read more: http://www.softick.com/news.html#83
Click to expand...
Click to collapse
It still makes my wizard to lock up...

Re: Softick Card Export II version 2.11! Now working on Wiza
bolasz said:
dddrko said:
read more: http://www.softick.com/news.html#83
Click to expand...
Click to collapse
It still makes my wizard to lock up...
Click to expand...
Click to collapse
It works for my 838.. I have lockup and unable to switch to SDcard mode only if I connected to my PC and activesync once and unplug. But that seems to be the activesync issue in my 838 which fail to free itself from unplug from PC. So it cannot switch to SDcard mode..and prompt me an error message.
I have already switch to AS4.1 but does not improve my situation.
What is Microsoft doing here?? :roll: A soft reset is the only way to get my device syncup again.. :x

I own this program since I had my XDA mini ...
finally I can use it again to copy some files to my pda and use it as a memory stick...
I also noticed some problems:
1. after I connect the USD cable and the PC recognized my pda as a memory stick, Windows XP asked me to make a reboot in order to be able to use the new 'harddrive'
2. after I copied a .jpg to my pda it looked like the storage card is no longer recognized by WM5. The icons of the shortcuts to programs I installed are missing and I cannot browse with TotalCommander to my storage card.
After disconnecting the USD cable, my storage card could be found again - is this a bug or a feature?!
After the first connect in mode 'Card Export' I switched to 'Active Sync' and the synching went on without any problems.
After agains swithing to mode 'Card Export' my Wizard gave an error message, as follows:
"Cannot switch between Card Export and Active Sanc modes. This may be because of missing dlls or corrupted registry entries."
This looks also to me like an incompatibility between card export and active sync.
Hmpf ... rebootet the phone and connected - voila - my Wizard was again properly verified as Memory Stick and I again could upload another .jpg to my device.
It looks definately unfinished ... but it is working quite acceptable to me, though there is a lot room for improvement, it will get the job done, if I need a memory stick 'on the go'.
My device is a HTC Wizard, O2 german.

i may be wrong on the second point, but activesync alters a file when you transfer it to the pda,
so if you transfer a file to the card (even using a card reader) then put the card back in the pda wm5 will not recognise it properly.
point 1 should only happen the first time of detection.

have no problem with my XDA II...

Chris09 said:
After agains swithing to mode 'Card Export' my Wizard gave an error message, as follows:
"Cannot switch between Card Export and Active Sanc modes. This may be because of missing dlls or corrupted registry entries."
Click to expand...
Click to collapse
I am experiencing the same... Please update this topic if you'll find a solution.

i'm having the missing dlls dialog problem too.
I noticed that once you activesync'ed, you can't switch to card mode and need to reboot the device.
However, mine can't seem to work anymore. It won't even switch. But I also tried disabling my today's screen (pocket plus and pocket breeze) and it works... but only the icon manage to change. My PC can't detect it as a mass storage device though.
Any luck?

Mine is working fine, I got that dll message once but a soft reset fixed it.

Just wondering what roms are you guys using that works with softick? I'm using rom version 1.6.7.1 WWE which doesn't seem to work. I tried hard reset and install softick on the first reboot. The computer detected a new hardware but failed to install the device.

vmirage said:
Just wondering what roms are you guys using that works with softick? I'm using rom version 1.6.7.1 WWE which doesn't seem to work. I tried hard reset and install softick on the first reboot. The computer detected a new hardware but failed to install the device.
Click to expand...
Click to collapse
I get exact problem, detects a HTC device, trys to load the USB Mass Storage Device, hang for a short period and then in Device Manager show up with a problem. Fails to install or display drive letter for SD Card in phone. Have tried everything, happens on XP and Windows 2000 PCs, tried various PC's, same problem.
Can anyone help
p.s - I have the T-Mobile MDA Vario phone, same as imate-kjam I believe.

eilz said:
vmirage said:
Just wondering what roms are you guys using that works with softick? I'm using rom version 1.6.7.1 WWE which doesn't seem to work. I tried hard reset and install softick on the first reboot. The computer detected a new hardware but failed to install the device.
Click to expand...
Click to collapse
I get exact problem, detects a HTC device, trys to load the USB Mass Storage Device, hang for a short period and then in Device Manager show up with a problem. Fails to install or display drive letter for SD Card in phone. Have tried everything, happens on XP and Windows 2000 PCs, tried various PC's, same problem.
Can anyone help
p.s - I have the T-Mobile MDA Vario phone, same as imate-kjam I believe.
Click to expand...
Click to collapse
Same here too!! using ver 2.12
ver 2.11 worked fine with me, so most probably I will downgrade to it now.
I emailed the tech support and waiting for their reply. I will post it here in case I get anything new.

I just tried v2.12, and it didn't work. I found v2.11 on some download site, and installed it. v2.11 worked fine on Qtek's 2.8.7.1 ROM.

I cant get this to work either using 2.12. I get the device manager problem as mentioned previously. Does anyone know where can i get 2.11 from?
found it here:
http://www.softick.com/files/CardExportPPC211c-softick-en.zip
but i get the same problem

You can find previous versions in the "download" section on the left.
I'm having the same issues, used to work fine with 2.11, then it stopped being able to write but could still read (this is on my Mac), and now with 2.12 I can't even get the thing to mount. I'm talking with the developer to see if we can get a fix.

Any 2.12 and 2.11 not working for me... My computer and three others shows me message that they don't have drivers

I posted a query on their forum.
Heres their reply:
http://softick-forum.com/viewtopic.php?p=35#35

pewe said:
I posted a query on their forum.
Heres their reply:
http://softick-forum.com/viewtopic.php?p=35#35
Click to expand...
Click to collapse
I'm a bit confused regarding their reply.
You asked a question about the Wizard and they replied saying they are waiting on delivery of HTC Universal to examine it better. I'm not sure what the Universal has to do with compatibilty for the Wizard as they are completely different devices with different hardware. (Mybe i'm wrong and the hardware components that Card Export uses is actually the same on both devices)

Puckster -
I noticed this on second look, and asked for clarification.

just want to inform everyone that there is a free alternative. it's similar to softick card export that it turns your device into a plug-and-play card reader. it's called wm5torage (yes, the number '5' is the letter 'S')
http://forum.xda-developers.com/viewtopic.php?t=45411&highlight=wm5torage
it does not have the system tray icon that enables you to switch between activesync and export mode, but rather you open the app in your accessories folder and activate/deactivate it from there.
but hey, it's free and it works

Unable to install programs via activesync.

i've tried to install AIM... and a webcam program.. both of which install through active sync.. however everytime I try I get the following message on my phone...
"Installation of (whatever).CAB was unsuccessful." and that's about all I get.
Also whenever I connect the phone to my PC is says it's unable to successfully syncronize and asks me to reconnect the device.
MS's support site has been less than helpful... any help you all can give would be greatly appriciated....

Installation problems.....
I am having the same problem too.
Even after a hard reset when I try and install Sprite Backup & Agenda Fusion I keep getting the install error: 'cannot be installed, try another location'
It's driving me up the wall! I would have thought after a hard reset this wouldn't be an issue. I'm now the proud owner of an MDA Pro (Universal) that I can't use because the software I want to install won't install.
Can anyone help me please?

Hi,
Couple of things you might consider / try: -
Establish an activesync connection, then use the "explore" button, navigate to your staorage card, and manually copying the .cab file from your pc to the storage card.
Then on the treo go to file explorer, storage card, and run the cab from the card.
The other thing is to check that you're using activesync 4.1 or later - updates are a free download from MS.
Hope this helps
Angus

Thank you for your suggestions.
Unfortunately i've already tried copying the CAB files straight to the device and launching them produces exactly the same result.
I'm also already using Activesync 4.2 latest version.
Is there anything else I can try?

judging from your sig, you're using a pretty old rom version... I would definitly upgrade it and then give it another go...

WM5torage problem - please help!

Many apologies if a solution to this has already been posted - if it has could someone lead me in the right direction?
My problem is with transfering large files to the Ameo's Microdrive. Activesync is too slow and wont transfer large files. I have tried two different versions of wm5torage, each time installing correctly and soft resetting. I am able to connect to my computer as a mass storage device without a hitch, and all files etc show up. The problem is that when i try to move, say a DivX onto the Microdrive after about 30 seconds I receive the message: "canot copy .....: cannot find the specified file. make sure you specify the correct path and file name"
Please can someone help me with this as it's ever-so-slightly doing my head in.
Many thanks
p.s. if it's any use i've tried this with both wm5 AND 6 with the same disappointing result

wm5torage works like a charge just dl on modaco forum then run it, your pc will see your ameo like a usbstick .

leoni1980 said:
Many apologies if a solution to this has already been posted - if it has could someone lead me in the right direction?
My problem is with transfering large files to the Ameo's Microdrive. Activesync is too slow and wont transfer large files. I have tried two different versions of wm5torage, each time installing correctly and soft resetting. I am able to connect to my computer as a mass storage device without a hitch, and all files etc show up. The problem is that when i try to move, say a DivX onto the Microdrive after about 30 seconds I receive the message: "canot copy .....: cannot find the specified file. make sure you specify the correct path and file name"
Please can someone help me with this as it's ever-so-slightly doing my head in.
Many thanks
p.s. if it's any use i've tried this with both wm5 AND 6 with the same disappointing result
Click to expand...
Click to collapse
i was gettin this error as well...
its something to do with activesync... screwing up
did you try restarting your computer that sometimes helps ?

xmen06 said:
wm5torage works like a charge just dl on modaco forum then run it, your pc will see your ameo like a usbstick .
Click to expand...
Click to collapse
yes it is off modaco and it does connect like a usb stick; its just that it doesnt maintain this connection during file transfer and gives the error mentioned above

Try these...
leoni1980 said:
yes it is off modaco and it does connect like a usb stick; its just that it doesnt maintain this connection during file transfer and gives the error mentioned above
Click to expand...
Click to collapse
Hi Leon.
What version are you running? Try this one if you're not already running it.
If all else fails...and this is cumbersome, but works everytime....use SafeMode Advanced and use it at boot time...no other drivers will be loaded and no conflicts.. It will def work then. After transferring your files, soft-reset to go back into standard WM5/6.
Let us know how you got on.

When I try with version 1.75 it is unreliable and often produces the error message you see. It may be luck but I've not had problems with 1.73. I disconnect the USB cable first before running, activate the software, then reconnect the cable.
When it does go wrong my Microdrive file table corrupts, also the Ameo hangs on the rainbow-wheel. I soft reset. Once I get it working I get errors if I need to copy the same file again. To fix this, I open WM5torage and run Check Disk on the Microdrive from my PC.

what you need to do is go to settings and the connections tab and turn off the advanced network functionality in "USB to PC". then use WM5torage.

I've tried unchecking "advanced network functionality" but to no avail. I've tried uninstalling activsync, and I've even tried it on a pc which has NEVER had Activsync on it - all with the same disappointing result.
Invariably WM5torage crashes and is 'unkillable' (if that's a word!) via Running Programs. Whatever I do it just crashes when I try to deactivate it.
I tried a hard reset of the device AND microdrive prior to installing Wm6 and THIS didn't work either. I've also tried the WM5torage cab posted in this thread by mackaby007. No luck.
I've tried Softkey Card Export ii as well and that just keeps reconnecting to activesync before windows even gets chance to recognise it as a mass storage device.
I think I've ran out of ideas.....
I'
Olipro said:
what you need to do is go to settings and the connections tab and turn off the advanced network functionality in "USB to PC". then use WM5torage.
Click to expand...
Click to collapse

yaughan said:
When I try with version 1.75 it is unreliable and often produces the error message you see. It may be luck but I've not had problems with 1.73. I disconnect the USB cable first before running, activate the software, then reconnect the cable.
When it does go wrong my Microdrive file table corrupts, also the Ameo hangs on the rainbow-wheel. I soft reset. Once I get it working I get errors if I need to copy the same file again. To fix this, I open WM5torage and run Check Disk on the Microdrive from my PC.
Click to expand...
Click to collapse
Just tried it with WM5torage 1.72 and that seems to be working fine.
Just transferred a 700mb file without hitch.
Wonder what the problem was with 1.75

try out card export 3.0
i heard this is a god sofwtare

I tried to see what could be wrong
I installed Card Export II but it would not ran and complains of missing dll's, but WM5torage 1.73 worked instantly. I have just transfered 3.5 Gb of music and some clips to test it. No problems yet and transfer took about 20 mins.
Could your problem be caused by installed software? Will have a look at Card Export 3 (never heard of it, or their notice must have gone to spam folder)

I've always been able to use version 1.73 smoothly in the past. Then, later I tried out version 1.75 thinking that it might work better. I could connect and activate. I had no problem transferring small files. However, it always stopped recognising the device as a valid USB mass storage a few minutes into the transfer operation. The de-activation would hang the device. I then went back to the older version that I still kept in my PC, (Modaco only has the faulty new version), and everything works again. I transferred a 3.7 gb file without problem.
So, make sure you do not use version 1.75 from the Modaco site.

doh!
I just read the first page and installed the 1.75 version which does crach my ameo as well. Can anyone tell me where to get version 1.72?

Please test the new WM5torage 1.78 beta version on your Athenas. It should again work on long transfers without glitches.
Feedback is needed, so please report in the main support forum here - http://www.modaco.com/WM5torage-t238545.html
Unless people with Athenas will participate in testing, there will be no good support for it...

Where can we get the 1.78 version
when I go to the link in the previous post, and click on download, it suggest only versuin 1.75
I'm having same error described in post #1 on my HTC Athena WM6.
Actually the error occurs only when using PC with WIN XP OS, while on my laptop which runs Win 2000 I don't have that problem at all.
Cheers

I've tried version 1.73, 1.75 and 1.78 beta 2 and only 1.73 is working.
On other versions i'm getting same error as Leoni
Cheers

I've tried loads of versions now but can't seem to gwet my hands on 1.73.
All the cabs marked 1.73 are 1.75
Can someone post a working 1.73 cab please

Johnston411 said:
I've tried loads of versions now but can't seem to gwet my hands on 1.73.
All the cabs marked 1.73 are 1.75
Can someone post a working 1.73 cab please
Click to expand...
Click to collapse
Here is version 1.73

the trick is to disable the advanced network support option in Connectivity in settings under the "PC-to-USB" icon

Olipro said:
the trick is to disable the advanced network support option in Connectivity in settings under the "PC-to-USB" icon
Click to expand...
Click to collapse
yes its a good while ago now since I posted that thread. but I do recall trying unticking the advanced network functionality box with my original wm5 tmob rom and also with the leaked wm6 rom. I also recall that it still didn't work. I really did try everything but only found success when installing the older version of wm5torage.I still cannot fathom why wm5torage 1.75 worked for some people but not for me. I haven't tested it since installing p.k.s black rom but will try tomorrow.
sorry to be a buttlicker olipro but cheers for your work by the way