Qtek s100 crash on low signal zone - JAM, MDA Compact, S100 General

Hi to all i'm new in this forum.
I've a problem with my qtek s100 device.
My configuration is the above in the signature.
When i go in low signal area my device freeze!
I can restart it only with softreset.
When the device is freezed no operation is possible other the softreset and if i try to call the device i ear the normal waiting call tone!
I'm seeking for a software update but in windowmobile.it my rom is the latest.
I hope there is someone can help me to solve this problem.
Thanks in advance.
Bye to all.

Related

Must reboot IMate PPC (XDAII) after every call - HELP?

Hi,
I have an IMate PPC (XDAII) with the factory installed Windows 2003, and service from AT&T (Cingular). Starting about a months ago, I've had to reboot my phone after a call in order to make another call or to receive one.
Before I try hard-reseting my phone or reflashing the roms, I want to find out whether anyone has an idea about whether the problem might be software, firmware, or hardware related. The phone works great, I just need to keep rebooting to keep it working. Thanks in advance for any advice on this.
I have exactly the same problem with my Orange SPV M1000. I've searched the forum very well. I could only find the same problem and no solutions.
Please help us!?

GPRS Problem :(

Hello all
My gprs connection works correctly, but sometimes it indicates "the connection with the modem has finalized" and then, if i don't do it a soft reset, this connections don't works again NEVER, there is no another solution, only a soft reset. Why? i cannot think to me that it is the only solution !!!
Anybody can help me please?
Thank you for all and excuse my bad english, it's very dificult for me
I have a qtek s200 and the radio version is 02.30.21
Thank you again
Nobody can help me?
Thank you
I continue having this problem, somebody may help me?
On my phone, when i turn off and later on, the GPRS connection it works again on my qtek s200, but why? where is the problem?... i don't understand anything
Please, i need any idea
Regards

GPRS problem at second connection

Hello,
I'm a Qtek S100 (Spanish) owner and I have a big problem:
When I try to sync my Qtek by GPRS there aren't any problem. I finish the connection holding the red button. After, when I try to sync other time, it isn't possible, it show an error and the only way to do it is turn off the phone and trun on.
Does anybody have a solution? It's actually comfortless.
Thanks a lot,
Josep
Hi, this sounds like its the callerID conflict problem.
Basically later versions than 1.20 had a conflict with GPRS resulting in failure to connect more than once without reseting the phone.
The fix was to replace the callerID with version 1.20.
I have attached this version & instructions below, this version is WWE (world wide english)
Check the BlueAngel forum for more threads on this.
This solution cured my S100 100%
Thanks Mr. B,
I have a question. I have watched the "About..." Caller ID program and it has shown me:
Caller ID for Pocket PC
Version 1.20 (Build 18586)
High Tech Computer Corp.
Are you talking about this program?
If I have this version, I have another problem.
Bye,
Josep
This is the program, but the version in my post is Build 17957
I would say its your problem for sure.
Do a backup before you try it to be on the safe side.
O2 & Imate removed CallerID from its ROMs because of these problems but this early build seems to be conflict free.
Thanks a lot Mister B,
This was the problem. I proceded as your information and the problem was corrected.
I'm going to test it two or three days and I'm going to post the "report" after the test.
Bet regards,
Josep

(help) auto disconnection esp for incomming call

Dear Guys,
Using softbank hermes and dopod english rom... always a problem...
The radio signal always automatically disconnect/ detach from the operator, it is quite often when recieveing an incoming call/ dialing a call...the radio connection went dead and appear '!X' logo as signal...
always need to reset...to make a successful call....
It has been annoyed me for some time...please advise!!
Thank you very much!!!
dogmood said:
Dear Guys,
Using softbank hermes and dopod english rom... always a problem...
The radio signal always automatically disconnect/ detach from the operator, it is quite often when recieveing an incoming call/ dialing a call...the radio connection went dead and appear '!X' logo as signal...
always need to reset...to make a successful call....
It has been annoyed me for some time...please advise!!
Thank you very much!!!
Click to expand...
Click to collapse
Sounds to me like you need to upgrade your radio to a newer version for better reception. See mrvanx guide at this link.
http://www.mrvanx.org/cms/

Imate Jam Calling Problem

Hello
I'm a Strange problem that my imate when i make a phone call it searches for the network or it turn off suddenly and the out going Call 16583 hours = 18 year or more
i asked before about this and try upgrade the final rom
but no Change.
Help please
there is a operator setting file on Imate.com for my imate but i can't use them
it report me when installing them that is not a valid windows CE application
Help please

Categories

Resources