Database Users

sync AS over BT v1.2

Hello 4 all, my firs post
Its for BT version 1.2
In PC trey BT icon push right butom > BT setup wiz. > "I want to find ..." > "Next" (beefore on HTC Wizard: turn ON BT , in BT settings make discoverable to other devices & erase old conections with devices "PC") > take "BT device " > "Next" > Pin code "..." > Initiate Paring > ... > enable ActiveS (Com20) > Finish > on HTC active AS & Dialup "Finish" > open ActiveS > Connection set. > Allow con. to "com20" (not allow USB) "OK" > On HTC disabled BT > On HTC "Comm Menag." push ActiveS > menu > con. via BT > Yes > COM ports > New Outgoing port > "PC" > > com7 > finish > device > take PC > "ok" > go go go
if not conected, try again after 10 sec. ">menu > con. via BT"
It`s working 99%<[/b]

i do it and nothing ...
Why incoming 7... it´s on local services or client aplication ?¿?
and i don´t show on the ppc the activesync services of the pc ?¿?

miguelromerom said:
i do it and nothing ...
Why incoming 7... it´s on local services or client aplication ?¿?
New Outgoing port !!!!
and i don´t show on the ppc the activesync services of the pc ?¿?
Click to expand...
Click to collapse
In PC trey BT icon push right butom > > BT setup wiz. > "I want to find ..." > "Next" (beefore on HTC Wizard: turn ON BT , in BT settings make discoverable to other devices & erase old conections with devices "PC") > take "BT device " > "Next" > Pin code "..." > Initiate Paring > what u see in "BT service selection"?
I have: ActiveS; Dial-up; OBEX ...; Voice Get.
I install AciveS and then BT soft.
[/b]

YES I´VE the same on the pc, but the ppc don´t dectect the AS service over PC

miguelromerom said:
YES I´VE the same on the pc, but the ppc don´t dectect the AS service over PC
Click to expand...
Click to collapse
Which moment U don't see:
On HTC disabled BT > On HTC push ActiveS > con. via BT > Yes > COM ports > New Outgoing port > "PC" > NEXT > com7 > finish > device > take PC >

take pc ?¿? why port 7
regards

miguelromerom said:
take pc ?¿? why port 7
regards
Click to expand...
Click to collapse
One moment, I need to try one idea!!!

ok thanks

miguelromerom said:
ok thanks
Click to expand...
Click to collapse
1)On HTC BT setings delete device "PC"
2)on PC in Windows Explorer unpair your device "HTC"
3)read my 1 post and try it! I liltle bit change it & try 3time, all works
Good luck

THANKS OF NEW BUT NOTHING
I HR the pda and reinstall AS and BT SW
Thanks

I'm not sure what i did but it works - that's all what counts
By the way - what is BT soft ?

mine is widcomm
regards

did you use comport 20 for you activesync connection?

no i haven´t got 20 port available ...
thanks of new

I think I've got it
But it's a little tricky
1. Delete all connections on Pc and PPC
2. Start the Setup-Assistent and choose I want to find
3. Initiate Paaring
4. Choose ActiveSync without secure connection.
5. Set com20 if possible.
6. Please go to your ppc properties on your pc and allow active sync
If you coose com20 you can quit here, if not try this:
7. Start->Run->Regedit
8. HKEY_CURRENT_USER\Software\WIDCOMM\BtConfig\Services\
9. Search the folder with Name=ActiveSync (I have 0010)
10. Change the ComPortNumber to 20.
11. Search with your PPC the services on your pc and take activesync
12. Go to the preferences of your bluetooth-enviroment of your pc and take the tab local services. Now change the com-port number of your activesync service to an existing one (I have 4).
Now it should work
km

What if my computer does not show Activesync as a bluetooth option. I can get PIM synchronization but no Activesync. How do I go about adding Activesync as a service my computer can use?

I think the Activesync service is nothing else then a serielle connection called "ActiveSync" with com-port 20. Just create this on manually.

i think tomorrow we have a new rom version, a uninstall AS, and HR to the ppc, then i do this test...
thanks

I have the same problem, when I try to connect from the PPC it says there's no partnership with an AS enabled PC. And when pairing / updating services, the PPC sees serial and handsfree services on the PC, but no AS. Partnership is established, it works fine over USB.
Like miguelromerom I also use the Widcomm stack. Mine is urrently version 5.0.1.1400. I tried several older versions as well.
On the PC I have an incoming bluetooth serial port at COM 4, which is named "My ActiveSync". Secure connection not checked. AS 4.1 is set to allow connections on COM 4. The service on the PC is active.
On the PPC I had optionally configured serial ports: incoming (7), and outgoing (6) to the PC. Set the non secure. Though I'm not sure if either of them is required. I suppose we're all agreeing the port numbers on the PPC bear no relation to the port numbers on the PC?
km said:
7. Start->Run->Regedit
8. HKEY_CURRENT_USER\Software\WIDCOMM\BtConfig\Services\
9. Search the folder with Name=ActiveSync (I have 0010)
10. Change the ComPortNumber to 20.
......
12. Go to the preferences of your bluetooth-enviroment of your pc and take the tab local services. Now change the com-port number of your activesync service to an existing one (I have 4).
Click to expand...
Click to collapse
I also tried this. I still see no AS service from the PPC when doing this. It is not possible to select COM20 in the AS 4.1 connection settings.
Eric

ActiveSync via Bluetooth
I am not sure how it will go with Wizard, but with Magician it help me.
I found this step, but I forgot the origin. So actually no permission from the author. I share this with hope can help others. Hopefully the author understand.
-----
1)On your PC go to the Control Panel and select "Bluetooth". In the "Options" tab, make sure all the ticks are on. You'll now see a little bluetooth icon on your system tray. Makes it easier to access in the future. Your PC should also be ready to be found as long as you ticked the fist box in the step above.
2)On your Jam, Go to Start, Settings, System (Tab), Bluetooth Settings. On the screen that comes up you ONLY want to hit start. Leave the incoming and outgoing checkboxes OFF!!!
3)You will now be taken to the partnership screen, where you just follow the instructions to add your PC. Follow through until you hit finish. Close everything down until you're back at the today screen.
4)Back to your PC, double click on the Bluetooth icon in your system tray. Go to "Com Ports" (Tab) and click "Add". Choose incoming. A You'll see an incoming port added to the list (probably be the only item there). It should look like "COM X Incoming"
Remember what number is after COM. Close all windows, making sure you hit OK or Apply where you have to.
5)Open Active Sync on your PC. Hit File, Connection Settings. Enable the first tick, and select the COM port you had to remember in the previous step. Hit OK
6)Open Active Sync on your Jam. Choose Tools, Connect Via Bluetooth.
-----
Regards,
Arto.

Connected to GPRS through XDA MINI S?

Hi all,
i have recently bought a laptop and as i am away alot, it would be helpful for me to connect to the internet through my phone. e.g. use my phone as a modem. However i cannot find any documentation on how to do this?
Can anyone tell me if this is possible, and how? I have tried through activesync but no luck.
If you could let me know that would be brilliant!
Thanks

Yeah its possible... just finished setting it up on mine This site helps:
http://www.filesaveas.com/gprsconnect.html
But i'll walk you through cos it took me a while to get it to work...
Firstly, are you on pay monthly or pay as you go?
There should be a program on you're XDA called "Modem Link" that is used for this. You can do it either over USB or infrared, though i recommend USB cos its much faster
Open this program and choose usb, then pick the Access Point you use to connect to GPRS normally on youre phone (check in the connection settings to see which AP corresponds to which settings if you need to) then press activate.
Now connect your phone to the laptop with the usb cable, and the new hardware wizard will pop up. Allow it to search the internet (you need a connection) and it'll install it automatically for you.
Then, On the PC, go to the Networking section of the Control Panel (Start > Settings > Control panel > Network)
Select "Make new connection" (this should start a setup wizard)
Choose "Dial up to Internet"
Choose the "connect via a modem" option
Enter the telephone number to dial as *99# (No area code, and turn off dialing rules)
Username for Pay Monthly is: o2wap
and for Pay and Go is: payandgo
Password for both is: password
When complete, go to Control panel > networks, and right-click on the icon for your GPRS connection. Choose properties and set the following: Connect Using - select your modem (infrared / USB)
You need change one other thing - to do with your modem settings. Do this as follows:
Go to Start > Settings > Control panel > Modems
On the Modems tab, select your modem, and press Properties
On the Advanced tab, you need to enter string in "Extra initialization commands". This initialisation string will need to be entered as:
+CGDCONT =1,"IP","wap.o2.co.uk" (for contract)
or
+CGDCONT =1,"IP","payandgo.o2.co.uk" (for PAYG)
Note the space before the =1. obviously dont include the bit in brackets.
I found I then needed to go into internet explorer and go on Internet Options > connections tab > choose "dail when network connection not present"
and then select the GPRS connection you made earlier > press settings > enable proxy server.
use the following ip address for the proxy server:
193.113.200.195
Now, I'm not sure which port number you will need, because it says to use 9201 but that didn't work for me, i use 8080. try both and see which will lets you load up a page.
press ok and try to load a page in IE. dial you connection when asked and it should work. try google as a test.
Tell me if you run into any problems.. I have it working on my pay as you go sim.. I have no idea if it will work on pay monthly, you might need to try using some of these settings:
http://www.filesaveas.com/gprs.html
-

Anybody who has Smart MMS Settings for WM6 Hermes?

Anyone who has the cab settings or the manual procedure?

If you have no luck here, contact Smart and they should be able to send them to your phone.
jenellej said:
Anyone who has the cab settings or the manual procedure?
Click to expand...
Click to collapse

Or, can always google Smart GPRS or Smart MMS. You should find all the configurations online.... this is assuming you know how to setup GPRS and MMS (in WM5 or WM6) in general.....

HTC MMS settings
Download HTC.COM new for WM6 (use the S710 file) works for Hermes WM6

HTC.COM use de File for the S710 works for Tytn Hermes WM6

Where do i download this file? Do you have the direct link?

http://www.europe.htc.com/support/software/htcs710.html
cheers

GPRS Settings
Go to Settings> at the bottom tap Connections>Inside it tap another Connections> then Advanced> Select Network> Under Network Management -" In My ISP" - tap NEW> Under "MY ISP Name" – set to SmartInternet > tap MODEM at the bottom,> tap" New" ,> Under Make a New Connection - Enter a new connection name (SmartInternet) , Under Select a modem - tap " cellular line (GPRS, 3G)", then "Next" > Under Access Point name enter – internet then next > at the next page leave the Username, Password, Domain Blank and hit Finish. Try now to connect using Pocket IExplorer
MMS Configurations
Go to Settings> at the bottom tap Connections>Inside it tap another Connections> then Advanced> Select Network> Under Network Management -" In My ISP" - tap NEW> Under "MY ISP Name" – set to SmartMMS > tap MODEM at the bottom,> tap" New" ,> Under Make a New Connection - Enter a new connection name (SmartMMS) , Under Select a modem - tap " cellular line (GPRS, 3G)", then "Next" > Under Access Point name enter – mms then next > at the
next page leave the Username, Password, Domain Blank and hit Finish Go back to the network management again and select whatever you wrote for "GPRS connection " > ok
2. Go to Start >Messaging> Menu - Under menu select MMS Configuration > at the next page bottom tap "Servers" > then tap New > Fill up the following
Server Name : SmartMMS
Gateway : 10.102.61.46
Port Number : 8080
Server Address : http://10.102.61.238:8002
Connect via : to whatever you enter in Network
Management area for MMS connection
Sending Size : 100K or try 250 K
Wap Version : Try either 1.2 or 2.0
>>Tap OK
this is for xda exec but im sure it can be used for hermes. hope this helps

2007 T-Mobile MDA Vario II - TomTom v6 GPS Settings

_______________________________________
Having Hard Reset my T-Mobile MDA Vario II and installed needed software applications I became challenged.
When Bluetooth pairing my Holux GPSlim236 GPS Receiver I was unable to select the needed communications port COM4
On my PDAs I have installed the Registry editor “PHM RegEdit”.
When I looked at my MDA Vario II Registry all GPS Settings was blank
Here I document and share the Registry and Device settings from scratch that resulted in my device pairing and Satellite Navigation working properly using TomTom Navigator v6.
1. Registry GPS Intermediate Settings
Select PHM RegEdit, or the editor that is your preference, and
Select HKEY_LOCAL MACHINE, select System,
Select CurrentControlSet, and Select GPS Intermediate Driver,
Saving repetition when prompted select OK
Select the Key name “Drivers” if it does not exists
Select “Edit”, New Key and type Drivers
Select Drivers and “Edit” and select New String Value
Value name: Currentdriver and
Value data: Control Panel Configured Device
Select Drivers and “Edit” and
Select New Key and type Control Panel Configured Device
Select Control Panel Configured Device
Select “Edit” and select New DWORD Value
Value name: Baud and Value data: 4800
Select Drivers and “Edit” and select New String Value
Value name: CommPort and Value data: COM4
Select Drivers and “Edit” and select New String Value
Value name: InterfaceType and Value data: COMM
Select Multiplexor and “Edit” and select New String Value
Value name: DriverInterface and Value data: COM5
2. Registry GPS Settings
Open HKEY_LOCAL MACHINE, select Control Panel
Select GPS Settings
Select “Edit” and select New DWORD Value
Value name: Group and Value data: 2
Select “Edit” and select New DWORD Value
Value name: Hide and Value data: 0 (that is value zero)
Exit Editor and Soft Reset Device
3. Device Connection Settings
Select Start, Settings, Connections and GPS Settings
Select GPS program port: COM5
Select GPS Hardware port: COM4 and select a Baud rate: 4800
Select Access and check box Manage GPS automatically (recommended)
4. Device Bluetooth and GPS Receiver Settings
Select Comm Manager and ensure Bluetooth is turned ON
Select Bluetooth Settings and COM Ports
Select and hold Holux GPSlim236, select “Edit”
Select Bluetooth Port: COM4 and select Finish and OK
5. TomTom Navigator software and GPS Receiver Settings
Start TomTom Navigator v6
Select Change preferences, Show GPS status, Configure
Select Other Bluetooth GPS receiver and select
Select GPS is connected to: COM4 and select done
Another intellectual challenge put to bed
PS I can confirm that settings documented here perform satisfactory on WM5 and WM6 device

watchdog2003 said:
_______________________________________
Another intellectual challenge put to bed
Click to expand...
Click to collapse
ummmm...here's the pat on your back you were looking for
*pat*
I'm sure someone may find this helpful though...and I'm sure that's why you posted this.
For sure.

Set up proxy & port settings for WLAN! H E L P

Hello! I have a problem with WLAN. I couldn't find where to set up my proxy and port settings for WLAN. If I go to the start > settings > conections I can't set up a wireless network, just 3g, bluetooth etc. (but there are settings for proxy), but if I go to start > settings > network cards and then tap Add new there are just options that i need exept those two. Help me please!
P.S. I have WM5 and Qtek 9000 (HTC Unversal)

OK, after about 10 minute trying, I finally get it done.
When you select one AP name in Wi-Fi setting,it will ask which profile will the connection connects to.( I use Chinese version, I guess it will be "Default Internet" and "Default Company" ).The two connection is the two you select in setting->connection->connection->advance tab, the upper is "Internet" the lower is "Company", and you can make a new profile here using the "New" button,here you will find proxy setting and enter some proxy , because you are just using this profile in wi-fi ,so the "moderm" can be left blank.
When you have done the setting, you can turn on Wi-Fi, browse some web site, in taskMgr(additional application I installed) you will find the ppc has establish a tcp connection to the proxy server you set up.