Related
Hi,
I just bought an MDA Pro direct from T-Mobile's website and it was delivered today. Unfortunately, while the PDA side of things works perfectly, it won't connect to T-Mobile at all.
On the 'T-Mobile' start up screen it displays the text 'No GSM' above what I think must be version information.
It reports 'no service' in the phone status bubble, and SIM Manager says: "Only emergency service calls can be made without a PIN" When I enter the PIN I was given, nothing happens. I think it goes into 'change PIN mode' because then I can put two more 4-digit numbers in (it doesn't matter which!) and then it says "Unknown PIN Status. Unknown PIN Error"
Unfortunately it isn't just a SIM problem as the SIM works in my O2 P800.
I've spoken with T-Mobile and they want to swap the handset, which would be fine if they had any in stock! I'm wondering if anyone here had any advice on ways I could try fixing this short of waiting for them to get in touch and tell me they have another handset I can try.
Any suggestions would be much appreciated!
Hi,
what is your local provider ? Is it T-Mobile, Vodafone, E-plus or O2 ?
The mda pro only works with a t-mobile sim !
- Superbowl
Try to clean the sim before putting it back in the MDA Pro,
Generally works for me!
i had the same problem with my jasjar here is Australia......my sim works on any other pda and phones but not the jasjar.....apparently the sim that i have or some of the new sims have a little higher voltage than normal.......and the jasjar dont like it.....so what i did was replace the sim with another one and that worked......al they had to do was port my number to the new sim......but before it did that tried to put the sim in first and it started to look for a network so i knew this was gonna work......becoz before when i put my old sim in it just says invalid sim or no sim........so try replacing ur sim with another one......perhaps try and get an old sim maybe the sim has some in stock.....i bet ya that will wrok....good luck
Thanks guys ... I'm trying to find an older T-Mobile SIM to try. It's just frustrating! I've tried giving the SIM a wipe, to no avail. If it is that the SIM is slightly incompatible, T-Mobile sending out another unit won't really help, right?
How annoying!
If anyone else has any great ideas I'd love to hear them!
try using someone elses sim and put it in the device and give it a try to check if its definitely the unit and not the sim......when i rang the tech support for optus thats what i was advised.....and they were right....sim voltage was the problem......anyways try getting another sim.
Contact customer services.
The problem sounds like you SIM is too old.
They should ask for your SIM serial number, if its too old they'll offer to send you a new SIM or something else to make it work straight away??? :wink:
The MDA PRO as its a 3G type phone with WCDMA it needs a diffrent sim card that is usaly known as a 3V USIM.
Its the same on Three in the UK, the sims from their phones will only work in 3G phones not standard GSM ones and vica-versa.
Old SIMs (from about 5 years ago) are rated at 5 volts. Newer ones are 3 volts (not just for 3G). Trust me, I work for a certain mobile phone company who sponser West Brom. ;-)
The problem will be fixed in a future software upgrade. But for now you need a new SIM or your phone unlocked.
Trouble is, this *is* a new SIM... I'm moving back to the 'hardware fault' diagnosis I think.
I went to a friendly carphone warehouse shop in Oxford and tried a new (and definately working) T-Mobile PAYG SIM and that gave exactly the same error.
Maybe T-Mobile need to send me a 3G SIM. I guess I'm probably just going to have to wait until they can send me a new handset to see what happens.
Ho hum!
There's no such thing as a 3G SIM. The 3G gigery pokery happens on the phone. There is no need for a different SIM. The MDA Pro has a problem with SIMs with certain serial numbers (Don't know which coz I'm not at work). You need either a SIM that the phone likes or your phone unlocked. Call customer services if you still have your phone.
Had the same problem allready twice in 2 weeks.
One time a soft reset made the device working again - another time I had to take out the sim card and put it in again, then it worked. But all email accounts were gone and had to be installed again.
Chris
Slave1 said:
There's no such thing as a 3G SIM. The 3G gigery pokery happens on the phone. There is no need for a different SIM. The MDA Pro has a problem with SIMs with certain serial numbers (Don't know which coz I'm not at work). You need either a SIM that the phone likes or your phone unlocked. Call customer services if you still have your phone.
Click to expand...
Click to collapse
Hi, thanks for that reply... it seems very useful! If you could post/pm me the numbers of those SIMs that the MDA Pro is unlikely to like I'd really appreciate it... customer services aren't striking me as very helpful (and certainly not knowledgable) and I can tell that if I call them they're still going to say: Wait until we have another handset in stock and we'll see what happens then. Which doesn't help me much as who knows when that will be?
Thanks!
Any SIM serial not starting with 06 or 07 will be affected by the issue.
eg 90043575, the serial starts with 04.
This will be fixed with a software upgrade in the future, in the mean time you either need new SIM or you handset unlocked. For either call customer services.
I got my MDA Pro a few days ago also, had the same problem as you, basically the handset is network locked, not sure how they managed to lock all UK network, basically give Tmob a call and make sure your stay on the line until they provide with an unlock code, i got mine, now my old sim works and my handset is unlocked
I got my MDA Pro a few days ago also, had the same problem as you, basically the handset is network locked, not sure how they managed to lock all UK network, basically give Tmob a call and make sure your stay on the line until they provide with an unlock code, i got mine, now my old sim works and my handset is unlocked
i had the same problem with my ASUS P535 (here is France) with new SIM card.
seen from :http://vip.asus.com/forum/view.aspx?id=20070818011855796&board_id=6&model=P535&page=1&SLanguage=en-us
Thanks.
I had the same problem BUT-
I had the same problem but i had been using the sim card successfully with the exec for a year, after a hard reset it doesnt recognise the sim. will a ROM upgrade fix it or is it a hardware failiure?
My solution
lauriewsmith said:
I had the same problem but i had been using the sim card successfully with the exec for a year, after a hard reset it doesnt recognise the sim. will a ROM upgrade fix it or is it a hardware failiure?
Click to expand...
Click to collapse
I had this happening to me just last week with a card that works all the time. Then followed that I had no sound coming off speakers or bluetooth. In my case it was a third party software problem. Don't ask me which as I install and uninstall too many applications and my Uni gets in a tangle sometimes. A soft reset instantly (in terms!) restored phone activities and sound, so I recommend a reset if you haven't tried it already. Maybe you will need more than one.
My mda pro is locked, can I still use it as pocket pc ??
whenever I start it without sim it only display T-mobile startup logo & dont go forward?
Tell me if its normal ? how can I use it as pda ??
thanks in advance for help.
Locked phones are in 99% of the cases stolen phones.
We don't do stolen phones here..
The behaviour you describe is NOT normal with the Qtek ROM.
Nor with the O2 ROM, I think.
You could perhaps reflash to a different ROM?
Bonzo said:
Locked phones are in 99% of the cases stolen phones.
We don't do stolen phones here..
The behaviour you describe is NOT normal with the Qtek ROM.
Nor with the O2 ROM, I think.
You could perhaps reflash to a different ROM?
Click to expand...
Click to collapse
Thanks for your reply, sorry offence not meant but plz keep your stupid comments with yourself.
just now I hard-reset & yes it solved the problem...
However just to clear things, I bought this phone very cheap from uk locked to T-mobile with the hope that its unlocker tool will be available soon
It is definately not normal. From whom did you buy this phone from? You probably want to go back to the store and have it checked. Have you tried a hard/cold reset?
You said that it will not run without a sim, so have it ever run with a sim (t-mobile or not)? If it did run before, I rest my case. If not, the phone definately not behaving.
Dare2Dream said:
Thanks for your reply, sorry offence not meant but plz keep your stupid comments with yourself.
Click to expand...
Click to collapse
I feel that my comment was rightfully made.
This forum does not like stolen goods, and we do make others aware.
As for the term "Locked", I have seen this used on both "Subscriber Locked" and "Barred/Banned" phones.
You have a "Locked" phone that you wish to use without a SIM card.
I then assumed that you had a stolen device.
How ever, I still gave a good answer to your question:
Bonzo said:
The behaviour you describe is NOT normal with the Qtek ROM.
Nor with the O2 ROM, I think.
You could perhaps reflash to a different ROM?
Click to expand...
Click to collapse
Dare2Dream said:
I bought this phone from uk locked to T-mobile. you should know that HTC universal still cannot be unlocked.
Click to expand...
Click to collapse
Yes, I am aware of this. How ever, I do believe that T-Mobile unlocks the phones for a fee?
Dare2Dream said:
Anyhow anybody can please answer my question. I have tried soft-reset but still it keep displaying startup logo screen.
Click to expand...
Click to collapse
As I said; I have given you my best answer; try a different ROM.
My Qtek ROM has no problems letting me boot without a SIM card.
I allso believe that the O2 ROM will let you do this.
With this knowledge in hand, I suspect that the T-Mobile ROM could have some software restriction that disables the use of the device without a SIM card.
The way to solve the problem would then be to flash the device with a different ROM.
You could alternatively try to reflash with a newer T-Mobile ROM.
[Edit]Perhaps this one: http://forum.xda-developers.com/viewtopic.php?t=38590?[/Edit]
So, the next time..
Please think twice before you refer to an answer as "stupid comment"?[/url]
If I start my O2 Exec without a SIM in it, I get a password entry box for the phone similar to the default one for my password-protected SIM, and there's a message saying that only emergency calls can be made ... blah blah..., but I can cancel this password screen and get to the Today screen and use the machine as normal. I think I press the Windows key on the keyboard to bring up the Start menu, from where I can choose the Today screen.
If your machine is locked by T-mobile in a way that means you can't get past a block screen then I'd say this is T-mobile protecting their investment if you don't have a valid SIM card.
Assuming you've tried a hard-reset already without success, you've got two options, I think:
- buy a PAYG SIM from T-mobile just to fool the machine
- flash the ROM to that of another provider (such as O2 UK) who doesn't impose a similar lock
Without knowing more about the T-mobile lock you're seeing it's hard to say more. I know that my O2 phone isn't locked permanently though.
Hope this helps.
Dare2Dream said:
just now I hard-reset & yes it solved the problem...
Click to expand...
Click to collapse
Oh bums. You've fixed it.
SiliconS said:
If your machine is locked by T-mobile in a way that means you can't get past a block screen then I'd say this is T-mobile protecting their investment if you don't have a valid SIM card.
Click to expand...
Click to collapse
SiliconS said:
I know that my O2 phone isn't locked permanently though.
Click to expand...
Click to collapse
Thus confirming my believes.
Thank you!
2 things :
- 1 : if tou want to unlock our MDA PRo call T-Mobile, pay £15, wait few days and you will have the code.
- 2 : normally there is no problem to use your Mda Pro as a PPC even if it is simlocked to T-Mobile. Just switch Off the telephone application. Try to put any simcard in, it does not matter anyway. If you're stuck with the boot screen your problem may be linked to a rom problem. Nothing to do with the simlock.
My MDA Pro SIM locked T-Mobile Germany works fine without any SIM card inserted.
Or to simplify get a t-mobile paygo sim from the uk.
br
I have an O2 XDA mini s as its so called, and an Orange Sim (both UK)
Now I can make/receive calls fine, but when I try to send a message, or goto the "phone" option, I get the message below. Nor do any contacts from my sim show up.
"The phone is not ready. Wait 15 seconds and try again"
Does anyone have some advice to resolve this as its pretty annoying!
I did try a search and got no results, so please forgive me if this is a topic that has been given the run around before.
Regards
Sam
Sounds like the simcard is dirty try taking it out and inserting again happens on probs every1 phone sometime.
Another option would be to go back to your cell provider and request they give you another SIM card
sounds like you might not be getting a strong enough signal to use the phone...or send out messages...consider flashing your radio rom to something higher (do a search for radio rom). radio rom flashing usually won't effect the os or ipl/spl...so you can keep all your existing settings. newer radios have more information on towers...so it has a chance to get a better signal...or at least that's what i've been told...
2.19.11 is common for cingular...but there's a post somewhere on changing something that will let you use higher radios with cingular without too many problems...personally, i'm messing around with 2.69.11 (t-mobile) and i haven't had any problems...
Tried cleaning the sim card to no avail.
As with regards to the radio rom, im sure thats the issue as i can make phone calls fine, so im getting a signal. It just seems accessing the sim card and texting is the issue
Its bugging me because its an awesome phone. Im wondering if its due to it being a different network branded phone to the sim card im using...
Sam
Ozington said:
Im wondering if its due to it being a different network branded phone to the sim card im using...
Click to expand...
Click to collapse
if that's the case, you may need to sim unlock your phone? but if you're making and receiving calls, you should be fine...
if the sim card is old, or the service provider was taken over...or something of that sort, maybe your sim card has a problem...something like this was a problem back in the US when cingular bought out at&t...the problem was resolved by consumers going to cingular to get a 64kb sim card rather than a traditional 32kb...perhaps something of that sort is happening there?
I suppose that is a possibility,
I will try using the unlocking tool, but im not sure it would be the sim as it is only 2 months old. I just didnt like the phone i got with the contract so bought this.
I will certainly try. I kinda wish i'd just bought the Orange version of the phone
Oz
@Ozington. If you can make calls, chances are your phone is already unlocked. Did you bought this phone 2nd-hand? The previous users may have done something to it. Soft reset your system and tell us all your stuff (especially the Radio/GSM displayed) displayed on the first boot screen.
Alternatively, if you want to avoid all O2 crap, hardreset your phone and during init setup, soft reset it (poke it) just after you have done your security settings. If it is not using official ROM (e.g. no O2 stuff around to be seen), make a guess on the ROM used, and you can also try upgrading an official ROM (safe to do so).
Hanmin,
The phone was bought from ebay, but was brand new sealed, all in o2 packaging, the seller stated it was unlocked. It was all factory packed and the seal wasnt broken..
The Device info is as follows:
Rom Version 2.21.4.1 WWE
Radio 02.07.10
Protocol 413.1.03
ExtROM 2.21.4.101
Does this mean anything?
Regards
Sam
I'm doubtful that it is factory sealed and unlocked. From the information you gave (although not those I've asked for), seems that your phone ROM is a bit, old. Go to O2 webpage and download an update for the ROM (I'm not sure, but I think they have an updated ROM).
To check your ROM version, tell me the battery icon on Today screen, is it on the top left or bottom left. Top left battery icon means it is AKU2, the updated version.
To throw a spanner in the works the battery icon is in the top right?
Thanks for your help. What info did i miss out? (Please bear in mind i have no idea what im doing with the more technical side of the phone!)
Regards
Sam
I briefly had this problem as well. In my case, I could also receive text messages, but still could not send. I changed OS's and it was fixed. The problem only seemed to happen with one of the new OS6 roms. It was intermittent, and even resetting the phone seemed to solve the problem occasionally and briefly. I have flashed my device too many times, but think it was the most recent Touchflo version that had the problem for me. I was using radio 2.69 Ipl/Spl 3.08. I hope this might help. Good luck.
Orange SIM & Unlocked T-Mobile MDA Vario
Hi Guys,
Just a quick note to say that I have a similar problem with my new Orange SIM.
All the GPRS works fine, calls send & receive OK, POP3 email works a treat but no text messaging and when I try Start > Settings > Personal > Phone .. I get "The phone is not ready. Wait 15 Seconds and try again"
I have no answers to this but from all the searching I have done over the past few days to try and find a cure this problem seems to be common to Orange SIM cards. All I can think of is that the Call Centre Message Number needs changing to get the txt messaging to work.
The phone has worked fine on other networks - no GPRS but text messaging & phone calls
Any advice gratefully received !!
Hi guys first poster so be nice
I've got the same problem but came from T-Mobile to Orange.
My IPL / SPL is 1.03 so I'm going to upload the newer versions on the fourm to my phone and see what happens tommrow. Havn't got the time at the moment but I'll post up how I get on.
Do you guys think this is a good approch to the problem I've got?
Hi Sasyboy
You posted just after me. I got my phone working great on Orange now. It has taken me 3 days !!
You'll have to be careful on how you do it. I just jumped in and it caused me a lot of work and time. and a long period where I thought it was bricked 'cos the bootloader screen stayed on and I lost all comms with the MDA
First make sure the CID is unlocked, you must read this:-
http://forum.xda-developers.com/showthread.php?t=285435
I wish I had. This may seem a long way of doing it, but you don't want an expensive paperweight do you ??
After you have unlocked the CID and updated everything as per the Dr P stickie (link above) and it is working, you then need to get the Wizard_Love ROM upgrade. I tried after doing all the Mr P instructions in the stickie but still kept getting the "Phone is not ready...." so I decided I then needed the Wizard_Love ROM upgrade. This took me ages to find, I tried to d/load it via uTorrent but only got 25% and then found it on a Russian website - anyway I have it now, and as I said you'll need it, PM me and I'll get it to you.
You will have to download several files and set half a day aside. If you are struggling PM me and I'll get the files to you as I have them now.
I just need to get the Ornge MMS settings right and then all is fine. GPRS, POP3 email, Internet, Txt messaging OK now, SIM manager works fine (didn't even have it before!) and can access all phone settings for call divert etc
Good luck. Any queries I may be able to help, but I'm no expert. I have spent hours looking at this forum and all the answers are there it is just getting them in the right order.
How do all,
Really happy I updated everything and now it all works fine. Thanks to the community. I love this phone and now with updates it's even cooler.
I bought hd2 from ebay 2 weeks back and it is currently locked with T-mobile. I tried unlocking code from few sites but all returned my money, is there something changed? Can somebody sugest some where can get the code
Thanks
Sent from my X10a using XDA App
for most new phones now, the networks are the only ones that have the unlock codes.
what you will have to do, is get a free t-mobile pay as you go sim card and put it in the phone. dial 150 and speak to someone in tech support. say to them that your friend had the phone, but has since upgraded and got a new phone, and has given you the hd2, but you have a contract with another network so you need an unlock code for it. there may be a £15-£25 charge for it, but they should supply you with one. you will need either £20 credit or a debit card (they wont take payment from a credit card or any other source) for the payment, a valid email address that you check regulary and the phones imei number (printed on the sticker under the battery or dial *#06#). whatever you do DO NOT mention ebay!! phone networks do not like you buying phones from ebay and may give you some bs excuse as to why they cant give you an unlock code. they should email you the code within 14 working days. they may be able to tell you over the phone or they may post it to you in a letter, so be prepared for that as well
after you have unlocked the phone, you will need to debrand it. to do this, install hspl3 on the phone then install either the generic htc roms (or of you can find it, the rom from the network you are on), or one of the many custom roms available. also have a look at updating the radio rom. then its just a case of getting the operator settings either by opening the comm manager, tapping the data connection icon (the left hand icon next to the words 'data connection') and choosing your network from the list, or contacting your network and asking for the settings. it may be worth updating your connection database (in the connection setup, tap menu>update database>select update the latest settings of all operators>then tap the update database button) this ensures you are using the latest settings and will also add any new networks to the list.
i would avoid 3rd party unlocking sites/shops, as they way to unlock new phones is often related to imei, and the codes cant be generated yet, so the networks are the only option
hope this answers your question
the above process is for the UK btw, not sure if its any different for other countries
got mine unlocked in 25 minutes this morning, mines less thena month old, cost $26, just message blowfish06 on ebay and tell him you want an unlock from the new database, he will bill your paypall and you should be all set by tommarow (or by this morning if its already past 12 were u live), cheers
Thanks for suggestions guys
Ill try ebay guy first if that didn't work then i'll buy the t-mobile prepaid card
Sent from my X10a using XDA App
matthewharmon102 said:
you will need to debrand it. to do this, install hspl3 on the phone then install either the generic htc roms (or of you can find it, the rom from the network you are on), or one of the many custom roms available.
Click to expand...
Click to collapse
if you install any generic rom onto a tmous it will permanently kill it, so although the advice is sound for regular hd2, DO NOT follow that advice if you have a tmous.
edsonbarron5 said:
got mine unlocked in 25 minutes this morning, mines less thena month old, cost $26, just message blowfish06 on ebay and tell him you want an unlock from the new database, he will bill your paypall and you should be all set by tommarow (or by this morning if its already past 12 were u live), cheers
Click to expand...
Click to collapse
Brilliant advice. 30mins for mine and only £5.45. So wish I knew about him 3 weeks ago when I asked T-mobile to unlock my G1. £15 and still waiting.
Never mentioned the new database to him for mine.
I am urgently in need of someone who can solve this network problem I have been having. Right now I can not access any mobile network with this phone.
I am using an Atrix 4g unlocked and rooted.
Basically, my problem is that my phone has been asking me for a "SIM network unlock PIN" every since my time in Italy.
I recently went to Italy 2 weeks ago, and came back yesterday. On my first day in Italy I bought an Italian SIM card from the Mobile Network company Tre, a company similar to AT&T. When I replaced my AT&T network card with the Tre one, it asked for the SIM network unlock pin. Seeing that I did not have a code on me at the time, and after trying several numbers given to my by Tre, I replaced the tre card with my original AT&T SIM card. I later learned that my phone was not international and I unfortunately did not call AT&T ahead to unlock it, causing the phone to lock network access. I learned that this is a security feature in case your phone is stolen.
I'm asking for your help because I spent literally over an hour with tier one and tier two support of both AT&T and Motorola technical support all telling me the same BS.
Before calling any support numbers, I went to an AT&T branch, and I told them the situation. They replaced my AT&T SIM card with a new one, yet the phone still asked for the SIM network unlock PIN. They then told me to call support and ask them about a subsidy unlock code. AT&T phone support gave me multiple codes to unlock the phone, but none of them worked. All of the SIM and IMEP numbers on the phone were correct in their systems too. After telling me exactly the same thing as tier 1 support, AT&T tier 2 then transferred me to common Motorola support tier 1 support. Motorola only told me to hard reset the phone, which I do multiple times every time I update your firmware anyway. The last hard reset I did to my device was literally 30 minutes before I called technical support. They then told me that the only thing I could do is to replace the phone under warranty with either motorola or AT&T.
However, I am in a pickel becuase my phone is completly unlocked, rooted, has CFW/kernel, etc...and I think that wards the warranty.
I have been using this same firmware ever since I got this phone during the last summer, and it has been working perfectly. After I put in the Italian SIM card, the network locks. I have no where else to turn but to an expert here on xda.
Is there anything I can do? The only thing I can think of is to tell my story to a nonobservant AT&T guy over at a store and ask him to replace it. However, I don't know what would happen if they found out my phone is unlocked and they gave me a new phone under warranty before realizing this...
Thanks
eurosport360 said:
I am urgently in need of someone who can solve this network problem I have been having. Right now I can not access any mobile network with this phone.
I am using an Atrix 4g unlocked and rooted.
Basically, my problem is that my phone has been asking me for a "SIM network unlock PIN" every since my time in Italy.
I recently went to Italy 2 weeks ago, and came back yesterday. On my first day in Italy I bought an Italian SIM card from the Mobile Network company Tre, a company similar to AT&T. When I replaced my AT&T network card with the Tre one, it asked for the SIM network unlock pin. Seeing that I did not have a code on me at the time, and after trying several numbers given to my by Tre, I replaced the tre card with my original AT&T SIM card. I later learned that my phone was not international and I unfortunately did not call AT&T ahead to unlock it, causing the phone to lock network access. I learned that this is a security feature in case your phone is stolen.
I'm asking for your help because I spent literally over an hour with tier one and tier two support of both AT&T and Motorola technical support all telling me the same BS.
Before calling any support numbers, I went to an AT&T branch, and I told them the situation. They replaced my AT&T SIM card with a new one, yet the phone still asked for the SIM network unlock PIN. They then told me to call support and ask them about a subsidy unlock code. AT&T phone support gave me multiple codes to unlock the phone, but none of them worked. All of the SIM and IMEP numbers on the phone were correct in their systems too. After telling me exactly the same thing as tier 1 support, AT&T tier 2 then transferred me to common Motorola support tier 1 support. Motorola only told me to hard reset the phone, which I do multiple times every time I update your firmware anyway. The last hard reset I did to my device was literally 30 minutes before I called technical support. They then told me that the only thing I could do is to replace the phone under warranty with either motorola or AT&T.
However, I am in a pickel becuase my phone is completly unlocked, rooted, has CFW/kernel, etc...and I think that wards the warranty.
I have been using this same firmware ever since I got this phone during the last summer, and it has been working perfectly. After I put in the Italian SIM card, the network locks. I have no where else to turn but to an expert here on xda.
Is there anything I can do? The only thing I can think of is to tell my story to a nonobservant AT&T guy over at a store and ask him to replace it. However, I don't know what would happen if they found out my phone is unlocked and they gave me a new phone under warranty before realizing this...
Thanks
Click to expand...
Click to collapse
Ahh, perm SIM locked.
Pretty sure that has to go back to the manufacturer to be fixed, if it can be fixed at all.
Just go ask for a replacement, they shouldn't be able to unlock it anyways.
Longcat14 said:
Ahh, perm SIM locked.
Pretty sure that has to go back to the manufacturer to be fixed, if it can be fixed at all.
Just go ask for a replacement, they shouldn't be able to unlock it anyways.
Click to expand...
Click to collapse
thanks for the reply.
However, two things:
1) I thought it might be permanent, but I was not sure. Back in Italy I remember the phone giving me a certain number of try's, so I now that I think of it I might have exceeded that, causing it to perm lock. Is there any other way in telling if it's perm locked?
2) Also, one of my concerns is that AT&T will see that my phone is unlocked and rooted and all of that, thus warding the warranty and the replacement. I'm thinking that maybe after I give them this phone and I get a new one, they look at the old phone in the future and will see that its rooted and unlocked. Is this possible or what?
eurosport360 said:
thanks for the reply.
However, two things:
1) I thought it might be permanent, but I was not sure. Back in Italy I remember the phone giving me a certain number of try's, so I now that I think of it I might have exceeded that, causing it to perm lock. Is there any other way in telling if it's perm locked?
2) Also, one of my concerns is that AT&T will see that my phone is unlocked and rooted and all of that, thus warding the warranty and the replacement. I'm thinking that maybe after I give them this phone and I get a new one, they look at the old phone in the future and will see that its rooted and unlocked. Is this possible or what?
Click to expand...
Click to collapse
1) Just putting your sim card in and having the phone not respond pretty much sums up the sim lock.
2) I would at least revert the phone back to stock. AFAIK, unlocking the bootloader burned some sort of efuse so returning it back to a true factory state is "technically" impossible, but I do remember seeing that you could at least relock(?) and removed the unlocked notification at boot. I believe you should still be able to access the phone even when the sim has been locked, just start it without a sim card in place. If you can bring it back to an AT&T build, I think you'll be okay if you're still under warranty.
Just remember that next time you travel, either have an unlocked GSM phone or get a sim subsidy code from the carrier that the phone is linked to.
Would getting a code from cellunlock.net work? Or is their code the same as the ones given to me by AT&T tech support?
AT&T tech support gave me three '8 digit numbers', which were randomly generated. None of those worked. DO you think a cellunlock number would work?
Also, I am reading up on some forums saying that people in my situation (who's phone does not accept any SIM card and still askes for the code), can get the phone to accept some codes by reverting to stock firmware and radio. This is by .sbf though....
If things haven't changed, I believe the sim subsidy unlock would only clear the phone for the next foreign sim card placed in the phone whereas a real unlock code would completely unlock the code. Once your phone has been locked though, I don't think that code will be of use anymore.
It wouldn't hurt to try to sbf back to a stock build provided you follow the proper instructions to not get the x1000 hard bricks. Aside from trying that, I would think your best bet would be to just get the phone exchanged under warranty.
Sent from my Galaxy Nexus using Tapatalk
SIM lock
Looks like you have locked your SIM. Since you have rooted your phone you voided your warranty , best bet is look for SIM unlock code from online probably ebay will give you cheaper options, try them if worked great if not then there is a tool to root/unroot any android device, I will post the download link once i find. restore the device to factory settings if it permits and unroot back . then claim for replacement.
Hi i just unlock my device after hours of investigation. You have to change the baseband. Here is what you have to do. Flash the baseband to the ones from brazil (search in google sbf not the zip ones), after the process you can put it back to the usa at&t radio. Ones you change to tha brazil radio (wipe always before changes radio), put one sim card of another provider and voila, the code will work. You need to have your phone with no registration of motoblur at all.
I hope it will help you.
Enviado desde mi MB860 usando Tapatalk 2
kemoli said:
Hi i just unlock my device after hours of investigation. You have to change the baseband. Here is what you have to do. Flash the baseband to the ones from brazil (search in google sbf not the zip ones), after the process you can put it back to the usa at&t radio. Ones you change to tha brazil radio (wipe always before changes radio), put one sim card of another provider and voila, the code will work. You need to have your phone with no registration of motoblur at all.
I hope it will help you.
Enviado desde mi MB860 usando Tapatalk 2
Click to expand...
Click to collapse
Hey this metod works with an lg p930 too?