Headset Jack Broken - MDA II, XDA II, 2060 General

The tip of a headset snapped off inside the black plastic headset jack, so the phone thinks that headphones are always plugged in. This causes the speaker to not work. I got a broken motherboard online for cheap. I am going to attempt to switch the jacks. Besides "That's a dumb idea", does anyone have any suggestions or words of wisdom? Thanks.
-Ross

Broken headphone socket
You could try a matchstick or something similar with a tiny dab of superglue, let the glue go off and with a bit of luck you'll be able to remove the bit of broken jack plug without disassembling your handheld. Good luck.

I should have mentioned that I tried super glue and disconnecting the battery and wrapping a wire arounda thin piece of metal and pulling out the plug with an electromagnet. Neither worked. It is lodged in there really good.

Nightmare! I've got a long shot but it may be worth a go. Given that some people are using the ink tube part of a bic biro pen to mod 2.5-3.5mm adapters I guess that the ink tube part is slightly wider than 2.5mm. Is it possible that you could slide a bit of ink tube in the socket over the broken bit of jack plug and pull it out?

i have to advice to
if you are going to dismantle your xda there is a pdf here that shows how you must do it and the tools for it search and you will find it (serarch my posts) i posted it here cant remember where lol
its a step by step guide ....

Related

broken headphone jack?

I've tried this in 2 XDA II's. I put my headphones it one and it works but you cant hear it and you have to hit the cap around a little for it to get sound for a slip second. I put my headphones in another XDA II and it works fine.. So obviously there is something wrong with this XDA II's headphone jack. The rubber cover to the headphone jack is missing, would this have any effect on it?
EDIT-
When I put it in the broken headphone jacked PDA when I insert the headphones in it makes a crinkle noise from me pushing it in. The other XDA II goes in smoothly. =/
Hi.
Rubber cap doesn't change anything (apart from stopping rubbish from getting into connector )
What you described is a case of worn out connector (in PDA).
It happens sometimes. Jack type connector aren't so tough, especially when you plug in and out often.
If you dismantle Blueangel, you'll have clear view of connector body soldered to PDA's mainboard.
You can do it. You can let somebody do it. Or You can leave it to professionals.
The connector needs to be replaced (very cheap part).
Maybe it's enough to bend metal terminals inside a little. A person who does hardware will know.
There's a optimistic version though.
Maybe only cleaning the terminals would do for you (I doubt it though).
It can be done without opening BA.
I'd recommend using some special spray (for cleaning electrical contact metals). Ask in electronic parts shop.
Good luck.
I ment my XDA II, not XDA IIs, lol. I have no expierence with opening the phone but I am good with electronics, but I don't know exactly what I'm looking for =/. I think I might just buy the HT820's Bluetooth headset, that would solve my problem overall.
Faulty socket repair...
Hey guys,
I have the same problem as above (crackling sound through headset) and the O2 service centre said it would cost £97 to fix.
But just did a web search and found a small company in London that said they can fix it (within 2 hours!!!!) for only £30!!!!
Im off to get it sorted so I'll let you know how it all went!!!
Richie Rich.
Mine wasn't like this until I bought it. I bought it from a friend for only $100USD because I'm very good friends with him, it works fine perfectly but the only problem is the headphones don't work in it (any headphones) and he knows there is something wrong with the jack, it wasn't like this until recently it happened. It's cheap to fix probably... but I'd rather just buy the HT820 bluetooth headset, its a good replacement instead of having to send in the PDA to fix a little headphone jack port I wont be ever using sooner or later.
but hey if that place fixes your phone, reply to this topic I want to know!
Headset Jack
I had this exact same problem in the past.
The headset would crack and go out every once in a while, sometimes I would have to move it around in order to get any sound at all.
I didn't do anything about it until it completely broke off, yes the inside plastic connected to the motherboard broke...
So I went to open it up, its not that hard, just a few screws, but I had to buy a torax screw driver (not that expensive)
I was also a bit shy about opening it, but I found this post:
http://forum.xda-developers.com/viewtopic.php?t=8525&highlight=opening+himilaya
you wont have to open it all the way up... just pulling the back cover off, then you will see the headset jack,
If it isn't broken or cracked then your solution would just be to take the metal connectors and a flathead screwdriver, and bend them,
Don’t bend the metal connectors too much so you can’t put a headset in, but just enough where there is definite connection around the headset,
You might want to put a headset in and see the dimensions before you close it (to save you from opening it up again)
You might want to clean the metal if it is dirty, ether with a dab of eyeglass cleaner on a soft cloth (eyeglass cleaner works well with electronics, due to the alcohol that evaporates)
Although if the metal is encrusted or rusty, you might want to take a small strip of sandpaper, or some abrasive object, but don’t rub too hard or you'll take them off!
Don’t worry too much about opening your device up; it is not hard, just open it with caution.
Good luck!
imablackhat, hi, did u mean that ht820 can output sound from media player & every sound from xda2? my current BT is bluetrek G2 and as far as i'm using it for talking only. how many hours the batt can last if we continously hear musics?
its 17 hours of music, www.expansys.com, search HT820, its the headset. I'm considering buying it for cheaper on eBay.

Looking for some help with headphone jack, semi interesting

hey guys,
here is the short story of whats up. I broke off the tip of a headphone adapter in my wizard. basically the smallest piece of metal is stuck in the headphone jack and refuses to come out.
First, any ideas on how to get it out, I tried toothpick/paper clip with super glue not too much luck. If its easy to take apart say so and I'll try that.
The other part is that my phone makes no noise and I can't talk into the mic on it cause the phone thinks there is constantly a headset attached. Anyone know a workaround on getting the jack disabled or a workaround like that?
Thanks in advance
It happened to me once. I took the phone apart, and poked a pin into the other end of the headphone jack (the one facing inside the phone) and it eventually popped out. Maybe you could try some small tweesers if you don't want to take it apart.
Taking it apart isn't so hard, you need a small torx key, and somethign flat to prise bits open.

About 3.5mm adapter - Are they stereo? Can a broken one be fixed?

Hi. I broke my 3.5mm adapter, two of the connections are now broken. I soldered both wires back but I don't know if they should be soldered with a specific contact. I chose the each wire with a contact, randomly. I put the little plastic case together and, of course, it doesn't work. The sound still comes out of the speakers.
So, is it ruined? The adapter is very simple so I thought I could do it myself.
My second question is that if I buy another adapter, would I have to buy one that's stereo? I saw some descriptions on ebay and some are listed as stereo and some as mono, but they look the same.
Thanks.
My experience
octavia said:
So, is it ruined? The adapter is very simple so I thought I could do it myself.
Click to expand...
Click to collapse
I did some surgery on my 3-in-1 USB Adapter and repaired it. I'd left my headset plugged into it when I put it in my bag and something must have pressed against it, pushing the socket at an angle and causing the case halves to split apart. I fully dissasembled it and when I realised the studs which the screws go into had broken clean off, it was out with the superglue with a thin bead around the edges and squashing the halves together in a rubber jawed hobby vice while it dried. It's all fixed now but as the halves are now inseperable, I cant tell you which of those thin wires goes where. The obvious choice would be to carefully inspect the blobs of solder to see which have a 'stump' of wire still embedded in them and try those but be careful because Russian roulette with the wires cannot be good for the circuitry in the phone if you get it wrong. There is a picture of the HTC extUSB pinout accessible through the Kaiser wiki and if you have a multimeter, some thin copper wire for probes and lots of patience, you should be able to work it out.
My second question is that if I buy another adapter, would I have to buy one that's stereo? I saw some descriptions on ebay and some are listed as stereo and some as mono, but they look the same.
Click to expand...
Click to collapse
I've not seen a mono one but as the device I have was very cheap (under £10) and plays stereo fine, you may as well splash out on a stereo one

Cradle-style holder with headphone jack for car

Bought one of these:
eBay - search for "FUZE Car Kit" - The one I bought was "C529"
Fits the Fuze like a glove... But best of all: I took the thing apart because I had no interest in FM-modulated sound and found the 3 wires that went from the quasi-USB connector to the modulator circuit board. Those three were (you guessed it) red, white, and black - the 3 wires needed for audio signal...
1. Took it apart totally removing both the switch and the modulator part
2. made a new back out of a piece of plastic
3. went to radio shack, bought a "stereo mini" (1/8) female receiver and wired it to the red/white/black wires that were going to the modulator
4. drilled a 1/4 inch hole in the side of the rest of the housing for the headphone plug
5. rewired red-to-red, black-to-black (since I removed the switch)
VOILA! What i WANTED! A cradle-style holder for the FUZE with a stereo (headphone) jack so that I can just plug in a wire to my aux-input and get my tunes through the radio without the crummy sounding modulation
Yay. Ok you guys may or may not find this useful - but just wanted you to know it was very easy and do-able.
bought exactly the same thing! the fm transmitter switches of randomly, plus I can't listen to my cd's from my car stereo.
Thinking of modding it so that I can attach a speaker.
Can you post a pic of your mod?
thanks
wanwarlock - what kind of car do you have? I ask only because you could do what I did to a "T". If you have a newer car with either a stock head-stereo that has an AUX or CD Changer input or an aftermarket stereo with one of those - then you're set! You can buy adapters on eBay that make your CD Changer/AUX input a regular RCA style input (Red/White). Then go to RadioShack and buy an adapter to go from a Stereo-Mini Female to RCA-style Male and you're done - just plug that wire into the stereo input on your cradle and you're listening to the phone... Unplug and you're listening to whatever else Let me know if you have questions
any pics...?
Yes step by step picutres please if possible i would like to do soemthing like this for my phone as well. And is there any way to get the microphone connection as well? So we can use something like this thanks
nvm: just realized the mic input thing was a usb connection. I was thinking it was the other type of connections like regular iphone headset connections.
(as requested).
The first picture is the cradle attached to a bracket I made... The Honda Pilot has a bizarre little pocket beneath the radio above the "not an ash tray" that is totally useless. I cut a piece of wood, attached a bent strip of aluminum to the wood and a piece of foam to the top of the wood (to allow for a snug fit in the pocket), drilled a few holes in the aluminum, and attached the cradle to the aluminum.
The second picture shows the cradle from the outside - the power jack and the headphone jack.
The last picture shows the wiring detail. Let me know if you have any questions -
mybikegoes200 said:
(as requested).
The first picture is the cradle attached to a bracket I made... The Honda Pilot has a bizarre little pocket beneath the radio above the "not an ash tray" that is totally useless. I cut a piece of wood, attached a bent strip of aluminum to the wood and a piece of foam to the top of the wood (to allow for a snug fit in the pocket), drilled a few holes in the aluminum, and attached the cradle to the aluminum.
The second picture shows the cradle from the outside - the power jack and the headphone jack.
The last picture shows the wiring detail. Let me know if you have any questions -
Click to expand...
Click to collapse
hmm interesting thanks so much for the pictures.
thanks for the pics... i imagine this wont work with the seidio case
extensive said:
thanks for the pics... i imagine this wont work with the seidio case
Click to expand...
Click to collapse
Not even a little chance - the cradle fits the fuze *very* snug. So snug that I might actually sand it down a bit. With a case of any sort it definitely wouldn't fit.
This is pretty sick I must admint. However, I find myself wanting a cradle that has NO electronic connections, that way I can take the phone out of the cradle and mess with it in my hand and it still be connected to the audio cable and/or power cable.
Anyone know of a good cradle like this?
seanvree said:
This is pretty sick I must admint. However, I find myself wanting a cradle that has NO electronic connections, that way I can take the phone out of the cradle and mess with it in my hand and it still be connected to the audio cable and/or power cable.
Anyone know of a good cradle like this?
Click to expand...
Click to collapse
why not just get the generic holder and a car charger?
USB Head Unit
Another solution that I am going to try shortly is hooking up the Fuze via usb cable and set it to drive mode. I might need to put the music in a root folder but I will report back.
I'm trying it on a Pioneer head unit with USB functionality input.
Has anyone tried this yet?
i think it can work. not too familiar with usb headunits i.e. file structure etc. what does your manual say? theoretically should work in drive mode.
my head unit only has aux in...

How to repair damaged headphone jack?

After having pulled out my headphones cable a little too vigorously, I am facing the problem that no matter which headphone I insert, the sound gets thin and disturbed. Still stereo, but really not good. The only thing I can do is slightly push the plug on the right side to the left, causing the inside part to be pushed to the right, which gives full quality sound again, but will return to bad sound once I stop pushing. So I assume some pin is bent inside the jack. Is there any way to repair this, or any idea what to do except buying bt headsets or a new phone?
Thank you for all helpful suggestions
Check if you don't have lint or some dirt in the headphone jack - I use thin sawing needle to dig out accumulated dirt from headphone jack and USB port every few weeks/months. If it won't help, you should be able to carefully bend the inside pin with the same tool. Strong flashlight will help to visually check the situation
As a last resort, you can buy the part from aliexpress, its like 3 dollars.
Take it to service center they'll do everything fr you

Categories

Resources