Related
Was told a few days ago, but just remembered...
WM2003 seems to re-use the RAM needed for the RAM copy of the bootloader. This means that once you've entered the bootloader, even if you've only briefly looked at the pretty colored bars, the device cold-boots when you reset to go back to the OS.
Funny thing is this happens on some of our machines, but not on all...
Having the same problem on my QTEK...
i reported this here like 2 weeks ago i thought it was only on my device!
:?
Yes this happenes as well on my XDA (german O2)with WM ( 4.0.01 and .05).
Unfortunately the Band switch ( XDA dev. version ) is not working as well.
regards,
Silver
Also happens to my os xda Asian version with the following details:
Bootloader: 5.17
Radio Stack: 4.21 (UK version)
ROM: 4.00.05 ENG (06/05/03)
Protocol: 32S54
Funny, I thought I was the only one having this problem...
This also happens on 3.x ROMs, sometimes it just resets, sometimes it does not.
On the same device, with the same ROM and the same configuration, writing whole ROM to SD didn't do a hard reset. 5 minutes later, brief look at the bootloader erased all data.
It's about computers, it has no system...
possible fix
Samething happened to me. after i set everthing up perfectly and all i did was try to unlock the phone.
I think i found a possible fix. u need to make sure ur device is not powered on when u enter the bootloader mode. so if u want to access it. press the power button to make sure screen goes off. wait couple of seconds and go into bootloader. i tried this and my device was fine after soft reset. let me know if this works.
alex
Alex
Thanks. Works for me on :lol:
Australian O2 XDA
Bootloader 5.17
Rom: 4.00.05
Richard
Hi all,
This is my first post :x
I downloaded the ROM (4.00.10) from the kitchen. At first, I downloaded EXE file but when I start upgrading my Qtek reboot and nothing happen, I tried many times. I read about upgrading via SD. I did upgrading without any problem. BUT when it finish upgrading, my device won't start. It hangs-up at splash screen and showing ROM version and Radio Version only. I tried many many times with no success.
I need some help please
my device info:
ROM version: 3.18.04 ENG
ROM date: 05/22/03
Radio version: 4.21.00
Protocol version: 32s54
--
Model No.: PW10A1
Bootloader 5.22
--
Thank you in advance
Bailamos
Download again with NB0 then upgrade from your SD.
Download again with nb1 then upgrade from your SD.
Thank you, socheat.
But I did download nb1 and I tried upgrading with the sd method and the upgrading was successfully but my device won't startup it shows only the splash screen ( NOT FOR SALE ** Powered By Micro$oft ** ) and nothing happen after this screen
I restored my old rom (3.18.04 ENG) and the device is working now, but I want to upgrade to WM2003 :roll:
Is that cuz I upgrade the Radio ? my old radio version was 3.25 ( not sure ).
Thank you , All
Bailamos
Got same problem with you Bailamos
My Bootloader is 5.17
Now by XDArit + SD flash + Wallaby patch, I brought my XDA back to 3.20.06 original from O2 already.
Wondering should I downgrade Bootloader to 5.15 or not?
In XDArit it has one upper box which we can put Bootloader in.
Should I put something like "loader515.nb0" in that box during loading OS on SD?????
UP :? Please
update
Please , I need help.
I tried to downgrade my device:
Bootloader 5.22 => 5.15
ROM 3.18.04 => 14.04
I thought it may help upgrading but that complicate the problem!!
NOW , I can't do any upgrade. When I insert the SD card and start booting, it show me the boot screen : PRESS ACTION to start downloading. as soon as I press ACTION it show : GSM OK and nothing happened!!!! It looks like I pressed the exit button ( I PRESSED the ACTION )
The EXE method still not working , the same as before as soon as it shows : 5 min screen , my device restart and it lose the connection with the ActiveSynic
ANY one CAN help ? P L E A S E
Pretty Please
Thank you
yes it will loose sync, but just leave it there!
some times it takes 10 minutes
but it will finish updating, trust me! that worked several times for me.
Thank you , ntabikha.
I'll give it a shot right now.
it didn't work
when my device re-start , the Program ( 1.09 ) show this message:
Can not open a COM/USB Port. Please use Device Manager on PC to make sure that COM/USB port is available and working properly
and terminate immediately after pressing " Ok "
I think there is something I don't know !! but there is someone may know !!
Is that happening cuz I upgraded my Radio Stack ?????????? ???? ???
It was something about 3.xx and it is now 4.21 !!!!!
Hi Guys,
I need your help .
I've downloaded the 4.00.16 ROM by mistake, it really didn't tell the ROM number, so now I want to revert to a earlier one and I can't.
I've got the following message: "ERROR: GetDeviceData - An established connection was aborted by the software in your host machine.
error getting devicedata" and then "ERROR 011: EXECUTE REMOTE COMMUNICATION PROGRAM ERROR. Cannot execute the remote communication program. Please make sure that the USB/Serial cable is properly connected."
PLEASE HELP ME, I'M REALLY STUCK NOW AND DON'T KNOW WHAT TO DO...
sumaetee said:
Got same problem with you Bailamos
My Bootloader is 5.17
Now by XDArit + SD flash + Wallaby patch, I brought my XDA back to 3.20.06 original from O2 already.
Wondering should I downgrade Bootloader to 5.15 or not?
In XDArit it has one upper box which we can put Bootloader in.
Should I put something like "loader515.nb0" in that box during loading OS on SD?????
Click to expand...
Click to collapse
Have you tried doing it without the Wallaby patch part? If not give that a try, no on the bootloader downgrade part!
HTH
Hello
I did downgrade my Radio stack. It was 4.21 now it is 3.23.01
But that didn't change anything. I'm still can't upgrade my device to 2003.
The problem is:
Method 1: (Program A / B)
my device re-start and the program showing this error msg:
" Can not open a COM/USB Port. Please use Device Manager on PC to make sure that COM/USB port is available and working properly "
Method 2: (SD)
It shows me the upgrading screen
Press ACTION to start downloading
BUT when I press action it go the bootloader main menu:
GSM OK
!!!!!!
That's it !!!
At the first time, my device was able to upgrade but it freez after finishing the upgrade. Now, it wan't even upgrading !!
ANY HELP !! PLEASE ??
** to the people who saying you can't downgrade your radio stack , that's not right .. YOU CAN .. I DID IT **
Bailamos
HI all,
I'm desperate...
I recently bought an 02 Orbit that was supposed to be unlocked.
So I downloaded PDAMobiz_Dopod_P800W_AKU301_v1.1.0_Lite.exe, unpacked it and double clicked on UpgradeRom_P800W.bat
A dos installation routine started, then I performed a hard reset by pressing the softkeys + stylus reset.
and now I"m stuck on the O2 logo, with some red informations written :
IPL 1.25.0001
SPL 1.25.0000
GSM 02.67.90
OS 1.28.0.0
but nothing else, the device doesn't boot :-(
I'm completely desperate... I had my Orbit working 1h only and now I still have my eyes to cry.
I've tried to install another ROM like ART_HTCWWE_11240501_026790_WWE_Ship, but when I launch ROMUpdateUtility.exe it says that no device is connected....
I tried to enter the bootloader but I don't understand how I could do that (by the way what do you guys mean by the record button? where is it?)
Could someone explain me how I can recover my crashed device please ?
Thanks in advance
ok I've found the record button and managed to enter the bootloader (red-green-blue screen right?). But it doesn't help. My device is not recognise by my PC anymore, no connection.
The problem is that I didn't make the procedure on IMEICHECK because the vendor said my Orbit was already unlocked. I know, I'm stupid, I should have....
Anyway, now I've my 30€ UNL file,
I've edited a ROM with the hex program, I've change "BsaD5SeoA" with "IMEICHECK save exe file" (I told you I'm stupid, or I didn't exactly understood what you mean, because I don't have any IMEICHECK.exe file)
I tried to launch a ROM upgrade but my device still not be recognised by my computer, even in bootloader mode.
Same **** when I try to launch the C3v1Unlock, it says no device connected.
Please, if you have anything to help me......
After i read this THREAD who explain how to repair my problem ...But it dosent work for me
When i want to flash it, it tell me :
INVALID MODEL ID ,with : RUU_Artemis_DOPODASIA_WWE_LOVE_1.28.717.1_INFINEon gsm4.1.13.30_02.69.90_Cmp_Ship_R.exe
INVALID UPDATE TOLL ,with : _ARTE_DOPODAU_12570702_026990_WWE_SHIP.exe
And after have made the TUTO !
Click to expand...
Click to collapse
I saw this post on an other thread... I am having the same problem... I bought artemis from ebay and the seller told me that it was unlocked... But i can't flash it with these ROMs... Did you find a solution? Is it really unlocked?
By the way when the window that tells me "INVALID MODEL ID" shows up at the bottom and to the right of the window there is i big number... Do you know what this is?
Same problem here
I have THE SAME problemhere. The same message on the boot screen. It seems that we are not able to use our XDA ORBIT ;( any more
At least we can download oreginal XDA Orbit english or German ROM OR if someone write RUU for Xda Orbit. Than would be easy - you just go to boot loader and you start your RUU, or easily put .NBH file to your micro SD and flash it from micro SD.Too bad I can just cry over my Xda Orbit. PLEEEASSEEE HELPPP
I also heard that FTP ROM site is going down ---- XDA GENOCIDE!!! What ARE you doing people!
Try the orbit ROM on ftp if it is still there
When a seller says a device is unlocked, all they mean is that you can use any sim card of your choice. To be able to flash another rom you need to CID unlock it. For the Orbit/Artemis family we only have imeicheck selling the program for unlocking cid.
My advice would be to look for the orbit rom on ftp. If it does not work, check with imeicheck if their program works when device is in bootloader mode, and pay them and download the specific application for your device. Good luck
I had a problem with my Orbit when I tried to change the Rom to the PDAMobiz one. I ended up recovering it by...
1 - Hard Reseting it.
2 - Connecting it up to the PC then running C3v2Unlock note v2 from the the IMEICheck site. This made the screen on the Orbit go bright white.
3 - Downloading the the Rom listed in this thread and following the instructions with in the same
It means that my Orbit is seen as a HTC P3300 but it feels quicker. You do need the UNL file from IMEICheck to keep it unlocked. But it worked for me.
Yes I tried everything in bootloader mode,
the C3V2 Unlock program launched but after detecting the device, it says my device is corrupted with a kind message "[probably by your fault]" ;-)
So guys, everyone who's trying to upgrade : CID UNLOCK YOUR PHONE BEFORE DOING ANYTHING, and carefully read the (excellent) tuto.
FYI, here's the discussion I had with Imeichek guys :
------------------------------------------------------------
Hi,
I'm a little desperate and I hope you'll be able to help me...
I recently bought an 02 Orbit that was supposed to be unlocked (I didn't know the difference between SIM lock and CID lock)
I understood, too late, that I should have ask for my UNL file prior to do this stupid "direct upgrade" I did...
Here are the facts :
1- I didn't follow the instructions found on http://forum.xda-developers.com that explained how to order the UNL file and Unlock the device unlocked
2- I downloaded a new ROM (PDAMobiz_Dopod_P800W_AKU301_v1.1.0_Lite.exe)
3- I unpacked it and double-clicked on UpgradeRom_P800W.bat
4- A dos installation routine the started, then when asked, I performed a hard reset by pressing the softkeys + stylus reset.
now I"m stuck on the O2 logo, with some red informations written :
IPL 1.25.0001
SPL 1.25.0000
GSM 02.67.90
OS 1.28.0.0
but nothing else, the device don't go further
I've tried to install another ROM like ART_HTCWWE_11240501_026790_WWE_Ship, but when I launch ROMUpdateUtility.exe it says that no device connected.
I managed to enter the bootloader but my device is still not be recognised by my computer (not connected message). I tried your C3v2Unlock tool but it says the same : NOT CONNECTED
So please, if you have any information or procedure I could try to fix my device, I would really, really, appreciate, especially after my 30€ contribution ;-)
Best regards
---------------------------------------
2007/2/17, [email protected] <[email protected]>:
Hello,
NO PANIC. You can fix the device. You have to find the CORRECT / a matching ROM for your device. For this you have to know what ORIGINAL phone it is (O2 Xda Orbit UK?)
Tell us what device it is and we try to assist you in fixing it.
Regards,
IMEI-CHECK Team
-----------------------------------------------
Thanks for your fast answer!
Yes it's an original phone, a brand new O2 Xda ORBIT, in box
Regards
Thomas
----------------------------------------------
Hello,
the language is important. Is it UK version?
Regards,
IMEI-CHECK Team
-----------------------------------------------
yes it's a UK version
-----------------------------------------------
Hello,
hmm, sorry to tell you but for the UK version there is no official ROM update available right now.
All you can to do fix it NOW is to send it to repair (service center).
For our customers we offer to fix the device for free (you only have to pay for shipping costs in both directions). We are located next to Glasgow UK. In case you are interested let us know.
Regards,
IMEI-CHECK Team
-------------------------------------------------
Ok,
I guess I don't have any other choice.
Wich ROM will you install if there's no official O2 Rom ?
What is the procedure, what's your adress, and how much will cost the return ?
Thanks a lot
Thomas
-----------------------------------------------------
Hello,
- we can install any ROM of your choice (it only needs to exist)
- we also will unlock the device and you can install ANY ROM you life afterwards
- the device needs to be opnened to use some special hardware to access the flash chip directly
- shipping back to (UK/EU) with INSURED Royal Mail is apx. (7 GBP/15GBP) depends where you are located.
Regards,
IMEI-CHECK Team
---------------------------------------------------------
ok thank you,
but will you be able to flash an O2 Xda Orbit with the french ROM that comes with the (Artemis) HTC P3300 sold in France ? this is exactly the same machine.
Regards
---------------------------------------------------------
Hello,
yes we can flash ANY available ROM to it.
Regards,
IMEI-CHECK Team
----------------------------------------------------------
here I am,
I guess there is nothing else to do.
First I want to thank you all for trying to help, then thanks to IMeicheck, they replied very fast and found a solution, even if I won't hae my Orbit for several weeks.
2- I downloaded a new ROM (PDAMobiz_Dopod_P800W_AKU301_v1.1.0_Lite.exe)
3- I unpacked it and double-clicked on UpgradeRom_P800W.bat
Click to expand...
Click to collapse
Maybe you should not have unpacked the file Just clicking on the file icon starts the procedure, which does some checks before actual upgrade starts.
I have switched so many times between the pdamobiz roms and the HTC one so many times I've even lost count
It's been easy for you... because your phone was CID unlocked ;-)
Well i had HTC ROM and now i have pdamobiz... That means that my artemis is cid unlocked???
my orbit is stuck on boot screen exactly as manples'. i tried to flash pdamobiz custom ROM. i can enter bootloader. can u tell me plz to what change "BsaD5SeoA" with "IMEICHECK save exe file" from imeicheck i've got c3v2unlock.exe & unl file. i tried flash it tru sd card-nothing. I've got o2orebit (ARTE200) please hlp
Psrejic, does your Orbit work again? I have the same problem. Can't get passed the splash screen because I flashed it with the PDAmobiz rom.
Only way to go is thrue bootloader. Did the SD flash work for you?
Same problem here Waiting for any solution ...
Only solution so far is imei-check service, witch will cost you: Price of sending to them: (UK) Then 20£+15£(aprox) to pay them for unlocking and repairing + sending back.
That's what I've done,
I received an email where they confirmed the reception of my device and that they flashed it with a new Rom. My device is supposed to work, it's great ! can't wait to try it.
Hi manples ...
You send it to imei-chek?
My Orbit works again! ... but not with a software solution.
I returned the phone to the O2 shop and they gave me a new one immediately. I didn't mention my PDAmobiz Rom upgrade offcourse.
It isn't the nicest way to deal with the problem, but when o2 flashes the rom on the phone they can sell it again.
Then I did the Imei-check solution. Worked and flashed the dopod rom on it.
hi to all yesterday I was your siimilar problem (I've try to install teh powermap rom...) so my Orbit O2 (original german rom) still only in boot screen, today I've try to install this magic rom:
art_tmouk_11311001_024990_wwe_ship.rar
I've press the comm manager button + power button + soft reset and my orbit it's enter in bootmanager mode so, i've install the TMobile UK rom (I was the O2 german rom...)
only in this mode my orbit work again.
bye
xda orbit stuck
i flashed my xda o2 orbir german rom with PDAMobiz_Dopod_P800W_AKU301_v1.1.2 and now it wont start at all i tryed to enter bootloader but i cant ( voice key and reset ) its stuck at o2 logo and :
IPL 3.04.0001
SPL 3.04.0000
GSM 02.00.90
OS 1.20.0.0
DOSE ANYBODY have a solution ? please help me !
keep up the good work ! thanks
Hi Profs,
there are some problems with a Artemis Update SPL (USPL) v.01. I've found this problem is several topic but there was no solution for it.
#1:
http://forum.xda-developers.com/showpost.php?p=1739577&postcount=413
#2:
http://forum.xda-developers.com/show...44#post1745844
#3
http://forum.xda-developers.com/showpost.php?p=1713596&postcount=1
The problem:
use USPL to get rid of the CID....count goes up to 100% screen shows black with green text, then pops to white. I need to do a soft reset to get it running again.
Then i use ROM Update Utility to update my p3300....and it still keeps hanging on 3%....damn. i get mad...!! Have read almost all here online...no virusscanner, no firewall....I use win XP.
i even tried without memory card and phone card....and nothing seems to work.......
ipl 1.14.0001
spl 1.14.0000
gsm 02.07.90
os 1.14.0.0
Who has any clue...?
With other words:
I've just got back my P3300 from repair, they changed the main board. With the previous main board I was able to upgrade the device and I was using the B&B versions.
But with this new board I'm not able to upgade the SPL. When I try to upgade the device after and start the start_uspl .exe the 10...20... ....100 my device become an interresting "blue screen" status and only the reset help to get out from this status. If I start the RomUpdateUtility.exe after the upgrade I got the error message #270
IPL: 3.13.0001
SPL: 3.13.000
GSM: 02.94.90
ROM version: 3.13.405.1.WWE
ROM date: 8/28/07
ExtROM version: 3.12.405.102
This is not the solution for the problem. I've tried it:
Plug in USB cable. Hold voice recorder button and press reset button. Bootloader will appear (Three color stripes). Then you may flash up ROM. (This works only for RUU installation types, not for PDAmobiz modified installator) Original english HTC P3300 ROM you may download form here: http://wiki.xda-developers.com/index...temis_Upgrades ....
Please help us to solve this problem....
Probably the same problem
This should be the same:
Hello POF,
I was directed to this link by Rudegar because I want to change the french ROM to English ROM.
The relevant data of my PDA is:
The version of the ROM: 1.14.406.1 FRE
Date of ROM: 9/27/06
Radio version: 02.67.90
Protocol version: 4.1.13.28
ROM extension version: 1.14.406.101
I tried exactly the way you described in the USPL_manual and everything went well till I got to a stage where I was asked to click the update button which I did. After then there was a window which showed "updating from current version to version 9.99". I was confused at this point but clicked "continue" and after this stage I got an error message and there was no longer a connection bw my PDA and my computer.
Thanks,
Jonat
Reply With Quote
http://forum.xda-developers.com/showpost.php?p=1784337&postcount=430
Also the same
Problem "lost connection PDA-PC"
Hi,
first I would like to thank you for goooood job to many people here !
Back to my problem. I have HTC Artemis (T-Mobile MDA Compact III), OS WM6 T-Mobile Czech version.
I ran start_uspl.exe on my computer. The part in DOS based screen seems to finish everytime OK, but finally the connection with PC is lost. Therefore when the PDA Phone ROM Update Utility starts cheking version the error "lost connection with PC" appears . PDA stay in "black screen" mode and only hard reset start it again as usual.
Does anybody have the same problem? Any idea, how to solve it ?
Thanks
http://forum.xda-developers.com/showpost.php?p=1773030&postcount=426
When the screen goes white, don't restart. Just start flashing to the new ROM. Worked for me
Unfortunately it not a white screen, it a black one, connenction lost with the PC, and only the reset PDA helps to restart the unit again....
lenocs said:
then pops to white. I need to do a soft reset to get it running again.
Click to expand...
Click to collapse
What im saying is when it pops to white, dont soft reset it, just start the upgrade.
Anthony2oo5 said:
When the screen goes white, don't restart. Just start flashing to the new ROM. Worked for me
Click to expand...
Click to collapse
that what i also do When the screen goes white, don't restart. Just start your RUU
lenocs said:
Unfortunately it not a white screen, it a black one, connenction lost with the PC, and only the reset PDA helps to restart the unit again....
Click to expand...
Click to collapse
Same situation as above. Depending on the Artemis, the screen might go white or black. Just don't freak out and keep on flashing the USPL. It WILL work and then reboot. Then you can flash the actual ROM you want.
Hello from an absolut newbie trying his first upgrade,
And I have just experienced the same problem than lenocs.
I have run start_uspl.exe, but when the screen is suposed to become white or dark, it becomes dark and the artemis is in fact totally off and connection is lost.
Anyway I supossed that it was because the scrren got black and I tried to run the update utility, but I´ve got an error (the terminal is disconnected or similar) and nothing happens.
I have had to soft reset the terminal and fortunatelly it seems that I still have my previous ROM and it seems that it works. But, do you know if there could be some "side effect" because the first step of start_uspl script?
Anyway I would like to move to WM6, so, any suggestion would be really appreciated.
Thank's a lot
When you restart, what is the USPL number?
Ooopppssss!
I didn't pay attention.
As I've said, I'm a newbie, so I was just woried because I thought I had "bricked" my new atemis.
How can I know now the USPL number?
Anyway I tried the star_uspl again (I'm a crazy newbie) and it failed. The artemis went off almost inmediately.
Thank you very much for your help
SpiggyTopes said:
When you restart, what is the USPL number?
Click to expand...
Click to collapse
solved ... at least for me
I think the problem is in SPL version 3.13 (or maybe anyone newer than 1.11).
Try different Artemis USPL - for me worked version from this page:
http://wiki.xda-developers.com/index.php?pagename=Artemis_DumpedRoms
It's very confusional, because file sizes and also dates are the same as in unfunctional version, but this one worked.
Hope it'll help you as it helped to me.
Maybe this can help you
I bought a 8gb card the week before, so I needed to update the rom in order to have my new SDHC working. But whn I was trying to update the rom, through UPSL 1.1, I had an error. This was the first time I had an error because I have modified the room many times before. My error was about a CMD.EXE issue, something like Error code line 26 "can´t spawn cmd.exe" so I was not able to change my rom. What I did was to copy CMD.EXE from Windows/System32 and put in the same folder where I had the start_uspl file, and finally works!
Do not ask me why, but this was the only way I could make works the update process.
Just try.
Rocheau said:
I bought a 8gb card the week before, so I needed to update the rom in order to have my new SDHC working. But whn I was trying to update the rom, through UPSL 1.1, I had an error. This was the first time I had an error because I have modified the room many times before. My error was about a CMD.EXE issue, something like Error code line 26 "can´t spawn cmd.exe" so I was not able to change my rom. What I did was to copy CMD.EXE from Windows/System32 and put in the same folder where I had the start_uspl file, and finally works!
Do not ask me why, but this was the only way I could make works the update process.
Just try.
Click to expand...
Click to collapse
do u have ur card in the phone while updating
you are suppose to remove the card
Problem solved (for me)
Hi,
i had the same problem error 270, 3% and lost connection with Activesync.
IPL: 3.13.0001
SPL: 3.13.000
GSM: 02.94.90
ROM version: 3.13.405.1.WWE
ROM date: 8/28/07
any way to upgrade was wrong ->> error 270
My good way was:
1. Downgrade to WM5 - original shipped ROM 1.12.405.1(link found on Wiki pages)
2. Under WM5 run USPL to unlock CID (now without any errors)
3. Final STEP - Upgrade to new ROM Artemis Touch 3.01 (without any errors by upgrade)
))
Now my Artemis seems to be OK.
I ran USPL with storage card inside the device...
no problem
switch SD card back to 2GB or smaller before USPL
Hi,
for me USPL did not work with my SDHC 8GB card but then I switched back to my previous 2GB SD card and then it works.
Perhaps the SDHC driver blocks USPL in some way.
Cheers,
Markus
i have been trying for 3 months
once i have upgraded my artemis to wm 6.0 everything seemed to be OK for two days... then the screen started to go black when i restart... şi downgraded to 5.0 but nothing changed... when i remove battery for a while, my arte works... when i try to do anything with it, the screen slowly goes black as if it is broken... please DO HELP ME! i am going to go mad... i have a new iphone, ihave i kaiser as well... but i miss my artemis very much...
Hello:
I have the same problem and realized hundereds have too. I have been checking in all forums and no asolution to it
The issue that happens to me is that I used USPL for upgrading to WM6 and worked, but now for the Touchflo it does not. Tried with all USB ports, tried with different computers and no good news.
The USPL msdos screen indicates that there is no connection at all in all percentage levels, then it bocomes dark and the 260 error whne installing the rom.
please help us soon !!!
we are in trouble!!
Same Problem : Screen shut down
Anybody can help us on this point ?
The only way to solve it is to remove the batterie during 30 min., then put it back and pray...
Then, for no reason, the screen shut down, a few minutes or days after
I've upgrade from WM5 to WM6 with the original Rom of HTC, it seems a little more stable but it shut down every 2 days when i'm lucky
help me to break & solve this problem, maybe can also help the other members..
I tried to upgrade my XDA to WM2003SE everything goes right,
bootloader first time i still use v5.22
but when I soft reboot it freezes on the OZUP screen and
message ONLY FOR MICROSOFT bla bla bla....
i get this ROM from http://www.romkitchen.de/ ==> WM2003SE
then downgrade bootloader from v5.22 to v5.15,
using MMC (flash SD) continue to special rom 1.2,
and then cooked again using PC2002 by my own creation based from
romkitchen, what i want to ask is :
i cannot connect again via dekstop activesyn if i want to change
my ROM because my cradle cannot detect my charger?? but if i charge
directly, its work. What is the problem?
is my cradle/dekstop broken at the charger socket?
so what i need to do? just change the wire or socket or
i use the step like at http://wiki.xda-developers.com/index.php?pagename=WallabyCradleMod
if i prefer use the 2nd method, is that really OK? so just used cradle/deskstop, no need
power charger again if i want to change ROM to WM2003SE, because only can use via activesync?
after i change bootloader to v5.15, keep trying to change but only can via Flash SD Card,
i change to WM 2003 final, still same problem....after finish, only screen cannot enter the
menu or else, only boot screen until i am waiting for 15 minutes??? then change again to
WM2003 but using from http://www.romkitchen.de/tools, still same again....boot screen again...
haiyaaaa.....what happen?? i dont know, tired, always overtime to do this,hehehhee...
all my friends, help me...need your advice ^_^V
*now, i still used ROM from PC 2002,cooked again using PC2002 by my own creation based from romkitchen.
bootloader v5.15
Microsoft Pocket PC --> PC2002
Version 3.0.12039 (Build 11178)
ROM version : 3.17.03 ENG
ROM date : 05/15/03
Radio version : 6.24.00
Protocol version : 324e4
Model No.: PW10A1
I can not really help you, but i was also in the same situation, that i have had a device, that doesn´t work with any other ROM than PPC2002
Flashed several WM2003 ans the WM2003SE but non of them worked.
So i rest at PPC2002
Stefan
ow ow...
auch.. ok, thanks for the comment, i give-up,hehehe..but only for now,
take a rest first but i dont know for t'mrow, actually from 10 flashed,
i got 1 success, can got WM2003SE but with almost empty battery,
i know the inside and already set all, including i notice bluetooth icon,hehehe..
but how? i wonder that my sx56 with fake bluetooth, only icon
but after i charge my sx56 then i soft reset, its gone, back again with only boot-screen, after that, i can't find again WM2003SE ROM only lock with boot-screen, and ONLY FOR MICROSOFT..blablabla...
and about for my cradle/dekstop? how is it? can u give me solution to fixed it??
btw,thanks for helping, tips & trick hehehe...
i will keep trying to find/solved this problem by my own way ^_^V
modify my cradle/dekstop success
its working, i try to modify my cradle/dekstop with that steps (look at the top this thread), and it's work...actually not me who did it, but my friend,hehehehe....i ask his help and he agrre to doit, but all the risk is still at me, now i can charge and also syncronized to my notebook