Hi, whenever I try to turn on the bluetooth on my XDA IIi, it displays the following message:
"Bluetooth Radio failed to turn ON due to insufficient driver memory available. You much perform a normal reset before you can turn ON the Bluetooth Radio"
I tried the little button on the bottom with a small pin while holding the power button on and withouth holding the power button. No change after resetting either time. What am I doing wrong, and what can I do to fix this?
Thanks
Related
hi, after instaling pretty much of applications on my wizard it just stopped respond. if u do a soft reset it boots but freezest on todays screen and thats it. there is a massage dispalied "low memory". i cannot do a hard reset, upgrade rom anything. is there any other way to perform a hard reset ?? (i tried comm mnr+voice+plus soft reste) HELP !!!
cheers, matt
Some people have joy with - turn off - press and hold comm, record and camera buttons and press power on.
If that fails you should be able to flash your device with the same rom. Turn off, press camera button and hold then press power button and bootloader multicolored screen should come up. Connect via usb to pc and reflash rom.
I have problem with power button. when push pwr button dont,t off pda, but when hold pwr then lights off.
Power is never shut off in PDAs, thats the way PDAs have been designed.
I have the same problem, he is not talking about a full power down. If you hit the power button quickly the phone does nothing. However if you hold the power button down for about 2-3 seconds the lcd light turns off as it should.
Because of this I have to wait 1 minute for the unit to suspend before putting it back in the holster.
Does anybody have any idea as to why this might be happening. Im not new at this so hard reset, soft reset.. new rom... new radio...turning up side down while chanting. It does not change......
It will do it right one or twice in a week.
Maybe somebody that understands the signal that the unit receives upon pressing the power button might be able to shed some light on this.... Again the button does seem to operate just not suspend when pressed normally (1 second or less)
I have done some more research and this seems to be a common problem for some with BAs but nobody has found out why. There must be some kind of common hardware fault.. Does the power button send only one signal or is it a multi signal device.
afbcamaro said:
I have the same problem, he is not talking about a full power down. If you hit the power button quickly the phone does nothing. However if you hold the power button down for about 2-3 seconds the lcd light turns off as it should.
Because of this I have to wait 1 minute for the unit to suspend before putting it back in the holster.
Does anybody have any idea as to why this might be happening. Im not new at this so hard reset, soft reset.. new rom... new radio...turning up side down while chanting. It does not change......
It will do it right one or twice in a week.
Maybe somebody that understands the signal that the unit receives upon pressing the power button might be able to shed some light on this.... Again the button does seem to operate just not suspend when pressed normally (1 second or less)
I have done some more research and this seems to be a common problem for some with BAs but nobody has found out why. There must be some kind of common hardware fault.. Does the power button send only one signal or is it a multi signal device.
Click to expand...
Click to collapse
Do you have a problem with turning on? First, we need to know whether it is hardware issue or not...
What you can do in the mean time with the turning off problem is by installing a poweroff app like shutdownme, psshutxp, etc etc...
Absolutely no problem with turning on from standby... Right now i just lock the phone before placing it back in the holster.
To make it clearer if you HOLD the power button down the backlight will turn off only. It will still show the display image and keys will still function (it dims)
Well, I had the same issue with the latest WM5 ROM. I thought I was too stupid to press the button, then I thought the button was broke, then I thought, I'll have to live with it.
Now that I have flashed to WM6, no problems at all! Never even came to my mind that this problem once existed. So I guess that some ROMs just have this particular bug?
Stefan
I have tried all the roms as well as 2003 and have the same issue in all of them. And im not alone.
Power off Problem
I'm in same condition.
Had the same problem when using WM2003 second Ed.
Now I've installed WM6 but nothing changed:
I cannot power-off/suspend but can turn off backlight if press and hold power button.
When in standby the button works fine to turn on the device.
Also, sometimes volume turns up continously with "noisy" beep ...
Anybody solved this problems?
Thanks,
Ruben
(WM 6 - 5.60.00 build 18125.0.4.2
radio 1.12.00 )
Power button has two modes:
1. Click mode: Click it once for a short duration. This turns off backlight and can be resumed by pressing it again or by pressing OK button
2. Press and Hold mode: Press and hold for few seconds and release. This mode will dim the backlight and no other button will bring it back. This is some kind of deep sleep in battery mode. To resume the original setting, press and hold Power button again for few more seconds.
(p.s.: I am not sure if this behavior is true for all the BA models)
April 1,
I know these modes...
It seems that "mode 1" doesn't work at all...
I would activate "Button Lock" (settings-->button--> Lock(tab)--> "lock all buttons except power button") to turn-off backlight and "lock all buttons except power button" but I cannnot...
You solved this problem?
I have had this issue of not being able to power off. One way I always got out of it was by clearing the registry hive. Unfortunately this brings the PDA back to the basic ROM. At this point the power button worked without any issues. Upon reloading the software the problem may come back. I believe the issue is related to some programs. I can't recall which program it was that seemed to cause the issue. One other thing I think that also worked was just entering the registry and getting back out and doing a hard reset.
I had the same problem with my 6600. the message button also didn't work. Believe it or not, to fix it. I banged the lower half (4-way area) on my desk a few times. Not hard enough to break the screen. But prolly hard enough to free what was prolly a sticky key. And now everything is working.
i am too
the same ...
when i press the power quickly , nothing happen
when i press the power for 2 sec. the backlight turns off
i tried every thing .... including formatting my BA
any one solve it ???
I have this same problem, my power button does`t work. i tried installing different roms but without any chance to fix it. maybe its an mechanic issue. i will change pwr button, i hope this work.
Look at one of my previous posts. I fixed it, twice, and other users have used the same metod to fix it. I think the problem is "hung bit" hardware related because you can also send it in for service, and they will change a chip, but i never had to.
I bought a new phone (HTC TOUCH 2) from China.
It is same as the original one.
My problem is: I can't do a HARD RESET or Soft Reset by Button.
I searched the forums and found some talking about pressing (VOLUNEUP+VOLUMEDOWN+Power.
others talking about VOLUMEDOWN+Power
I tried every possible key compinations to do the HARD RESET with no success.
When i press VOLUNEUP+VOLUMEDOWN+Power, a green screen show up with the bellow data:
"THIS OPERATION WILL SET KITL MODE.
CURRENT SETTING........
DISABLE KITL: CAMERA
PASSIVE KITL:VOLUMEDOWN
ACTIVE KITL: VOLUMEUP
I searched for a Camera button but it seems this button is not there at all, only one tall button on the left side for Volume (up+down)
Also there is no Reset button at all, i searched every where in the mobile with no success even if i remove the styles, nothing there at all.
is there any help?
I have some problem with my htc clone i have no camera button but i must change kitl to disable to comunicate my htc with pc with active or passive kitl mode usb connection are not recognized by my pc. Is there any way to change kitl mode using wm mobile aplication or something like that i want to change my rom too. cause this one is probably for another htc with camera button
Hard Reset
Go to menu -> settings -> system -> clear storage to hard reset your phone
don't work with my problem after clear storage kitl stays in passive mode i need disable for usb comunication
Also, all owners of this mobile having the below problems:
1- Can't load normal Rom files (.nbh), they should load it through a flash memory
2- Rom File size should be smaller than 128mb.
3- Can't connect it with PC Post#2.
4- No Camera Button !!!!
Mine was disabled and I don't know which combination of buttons I pressed to enable it but now it really startups slow and also the usb connection problem came up. So anyone?
I tried each and every possible key combination with no success to Disable kitl.
Any help?
I would never trust a clone for a wm as i do keep all of my work on it. Never ever trust a chinese clone company for this. Better to pay a few dollars more and buy the real one than risk loosing all of my data kept.
You are right 100%.
but, what about the current case?
Do i have to put it in the trush bin?
Ravash said:
Mine was disabled and I don't know which combination of buttons I pressed to enable it but now it really startups slow and also the usb connection problem came up. So anyone?
Click to expand...
Click to collapse
Press (VolumeUP + VolumeDown + Power) then select Passive again...Working fine
Once press the "Windows logo" + "Volume Up" + "Power" working hard reset
Hard Reset is easy. Press the Volume up an down key from the center.i.e press it form the middle. like that both the up an down keys would be pressed. then Power on. Easy. yes it wasn't easy for me too in the start but a bit more pressure and it works.
Gothik said:
Hard Reset is easy. Press the Volume up an down key from the center.i.e press it form the middle. like that both the up an down keys would be pressed. then Power on. Easy. yes it wasn't easy for me too in the start but a bit more pressure and it works.
Click to expand...
Click to collapse
I have the same problem. Yesterday I put my cell phone passive KITL mode, but when I connect to my computer, nothing happens.
I did hard reset and soft reset but nothing happens.
Help me!
have you installed microsoft activesync (windows XP) or windows mobile device center (vista or 7)? i think you have to install those first.
robekia1 said:
Press (VolumeUP + VolumeDown + Power) then select Passive again...Working fine
Click to expand...
Click to collapse
How do you Select passive, when you get the screen of "this operation will set kitl mode. thank you
The screen will guide you.........
DID YOU REALLY PRESS THOSE BUTTONS?
Hi all,
I have accident on sea where one wave splashed a bag where my phone was. After small problems with "laggy" buttons everything went fine and my phone worked correctly except power button. It doesn't react. I couldn't even restart the phone. And when my battery was used I coudnt turn it on. I tried to press volume up + power button million times, or all 4 buttons, and somehow I manage to turn it on again while still I was on vacation. Few times I have entered Android recovery screen, and Power button worked perfectly there (I managed to press power button and select reboot device). And after the phone turn on power button would usually works few minutes and then it would died again.
I have installed software for simulation of power button and it worked ok. This morning somehow I decided to turn off my phone, and I couldn't even imagine what kind of problems I will have to turn it on again. Whole day I am trying to turn it on, but it doesn't react. When I pull in charger then it shows regularly battery status (70%). I am desperate :crying:
I am trying to google or find any solution how to bring it ON again without power button, but without success
Is there any way how could I turn Samsung galaxy S6 Edge Plus without power button?
And what you think, is this some kind of software problem, and maybe some factory reset or flashing might help? Or it is more likely hardware problem?
Many thanks in advance.
Can anyone help me?
I have just found this article which might help me:
How to turn ON Galaxy S6 without using the power button:
When the Galaxy S6 or Galaxy S6 Edge is turned off, press and hold the volume button for a few seconds.
While holding the volume button, connect the Galaxy to a computer using a USB cable.
Wait for your phone to boot to Download mode.
Then press down on the volume rocker to cancel the operation.
After the operation has canceled, the Galaxy will reboot and turn on.
You have successfully turned on the Galaxy S6 without using the power button.
source: http://recomhub.com/blog/how-to-turn-on-and-off-galaxy-s6-without-power-button/
But somehow this doesn't work for my phone? First I wasnt sure which volume button should be pressed, so I tried with both in all combinations and still cant get into Download mode.
But I am glad that samsung had created some workaround if power button is not working. THis used to work on older models I guess.
Is there anyone who might know the way how to turn on phone without power button?
Ok, apparently there is no recovery mode for the device or any other similar unbranded devices. The only way to fix firmware or any other issues is to flash it directly using the sequence below, especially if you don't have physical buttons. Make sure you have the firmware in a usb drive directly plugged in without extension cable, or using sd card slot.
Turn off the power to the HU, then press reset button, and keep it pressed. Then turn on the power, the illumination should remain dark at this moment due to the reset button is still pressed. After 3 secs, release the reset button, and immediately when the HU start to illuminates, turn off the power, then turn it back on in quick succession. The screen should show start update, and the progress will be shown on the screen.
You don't need to take the device out from your car. Just turn the key slightly, no need to turn on the ignition, to turn the power on.
Hope it helps somebody.
Hi guys,
Any idea how to enter recovery mode with this hu? It does not have physical buttons. Pressing reset button for few seconds did nothing. Thx in advance.