Hi,
the pad of pin14 is miss after soldering a new connector.
The USB cannot connect with PC now.
Can any one can tell me which one is the test pad of pin 14?
or can I find it on the jtag connector?
Edward
Related
Hi
I'm looking for USB in extension port or somewhere else on the mainboard becouse it's been dameged under the sync/charge port and I need to rewire USB from somewhere else. Also does anybody know why joystick don't work ? mechanicly it's perfect so I have no idea.
Anyone? Please help...
Hallo, I have the same Problem. I have only few soldering pads of connector after the connector is cracked out. But if you kann see, evtl. under microscope, there are little holes, which connects to the pads, if the pads are OK. I measured some pads and found the following points . See pictures..
I has not tested the functionality yet! because i have no connector yet -->Caution! If you or somebody could still check the Pins again, would be great! Because I have no second Board and I cannot be sure with 100%.
Hi all,
I have a CHT 9000, and the mini usb charge cable just wont charge it.
After inspection, I determined the source of the problem - damaged mini usb port pins, bent and loose, that cable wont even touch the pins to charge...
I need to know how to replace that mini usb charge port connector...
Thanks
commandosolo2009 said:
Hi all,
I have a CHT 9000, and the mini usb charge cable just wont charge it.
After inspection, I determined the source of the problem - damaged mini usb port pins, bent and loose, that cable wont even touch the pins to charge...
I need to know how to replace that mini usb charge port connector...
Thanks
Click to expand...
Click to collapse
Thankfully that is a part which is relatively easy to solder. Armed with a fine point soldering iron it's not too difficult at all. If I remember it has either 2 or 4 soldered anchor points and then of course the fine connections at the back end.
You may find a new port online or buy up a device that is being parted out.
For full functionality you need the 11 pin type (Not the 4 or 5 pin). See here:
http://www.displays-on-stock.de/adv...m0rpj9gchu55mp51ne83&keywords=11+pin+mini+usb
Mike
I have Hima with broken connector. Now i want replace them with usb mini connector.
Pinout is on http://forum.xda-developers.com/wiki/index.php?title=Connectors
I want to join pins 13*14*15 and 16-17-18GND with USB 1-3-2-4pins
But I still have one question... May I also connect three pins 20,21,22 to pin 13(+5v) if I want to recharge batteries directly from usb?
No need to connect all that pins: http://forum.xda-developers.com/showpost.php?p=10453499&postcount=71 and: http://forum.xda-developers.com/showpost.php?p=10467485&postcount=73
Thank you very much. I was looking for it here,but my English is´nt good.
Hi
I have a spare asus vivo tab windows RT dock that has a battery, nice keyboard and a USB in it. Asus tab connect to it through a 36 pin connector.
I would like to use this dock with my google nexus 7 or with my raspberry pi. I think 36 pin connector has hdmi connections and a USB connections. I am looking for pin connections of this dock 36 pin connector. I also need a matching female connector. Can someone help me find pin connections and a matching connector please. Thanks
http://forum.xda-developers.com/showthread.php?t=2115246
Hello everyone,
I want to install the tablet on my car's dash but it barely fits.
I managed to open the back case of the tablet and exposed the connectors. I could solder some wires to extend the connectors but I ran into trouble in figuring out the pinouts.
It has a some side pins that go from the microusb port but I'm not sure if I should connect 5V there.
Also the audio jack has 5 pins which I don't quite understand what they do.
Any sort of advice or information will be appreciated
Thank you,
Adrian