Hi everyone,
I am a newbie on this forum (and with my phone too !).
Before posting, I have searched for the answer through
the forum, and I haven't found the answer.
So here is my problem:
I have a bluetooth headset (multiTooth from Freetop.net).
It works great without Bluetooth (automatic transfer
of the incoming and outgoing call to the headset)
but with Bluetooth Tools package, it doesn't work well
(no automatic tranfer, difficult to manually transfer the
call, etc...)
So what is the problem, you should ask ??
In BluetoothTools packages, two features are very interesting:
1. power-saving profiles
2. automatic switch-off and switch-on of bluetooth
Is there any other softwares which provide only these
two functions ?
Thanks a lot in advance
Regards
BLG
Related
Hello. It is the first time that I write in this forum, although I read to you daily. I also want to apologize by my little dominion for the english lenguage. It wanted to give first, the congratulation to the creators of this Web by his I magnify work. Soon i will do a donation, since very I am satisfied.
My question has been written already in several occasions. My headsets bluetooth receives neither music nor you order them oral of my Navman navigator, single receive telephone signal. Somebody can help to understand this problem me and like solving it.
Thanks and a hug to all. :wink:
If I understand you correctly - your BT headset is working correctly in phone calls, but will not play MP3 files nor the audio instructions from TomTom.
If I am correct, then your headset is working perfectly. At this time, only telephone audio is supported by the BT headset . . . no other audio will be available through the BT headset.
HTH!
Thank you very much.....¡
Thank you....¡¡¡.....
Hi everyone,
I am a newbie on this forum (and with my phone too !).
Before posting, I have searched for the answer through
the forum, and I haven't found the answer.
So here is my problem:
I have a bluetooth headset (multiTooth from Freetop.net).
It works great without Bluetooth (automatic transfer
of the incoming and outgoing call to the headset)
but with Bluetooth Tools package, it doesn't work well
(no automatic tranfer, difficult to manually transfer the
call, etc...)
So what is the problem, you should ask ??
In BluetoothTools packages, two features are very interesting:
1. power-saving profiles
2. automatic switch-off and switch-on of bluetooth
Is there any other softwares which provide only these
two functions ?
Thanks a lot in advance
Regards
BLG
Hi,
I urgently need an utility which performs autoanswer on calls, even if bt headset or no headset are used. I'm disposed to pay for this...
Start->Settings->Phone->More
Automatic Pickup : Answer incoming calls without pressing talk after [x] rings
No, this only works with wired headset. I need it alway working, expecially with bluetooth headset.
Hi,
If you're still looking for solution to this - check out phoneAlarm, it has an option for this in the Advanced Settings
cheers
Bruce
Can any HTC Autoanswer on Bluetooth ?
Hi,
1) has anyone any first hand experience with ANY HTC pda/phone that could autoanswer on ANY bluetooth headset
1a) my experience is NO ! (Verizon XV-6600, A&T Tilt)
2) Unless there is a yes answer to 1)....
how could this have gone unaddressed thru so many generation/models/reviews of PDA/phones ?
2a) I can't accept that this is a "feature".
Jeez, just about every "dumb" bluetooth mobile phone does it just fine.
The idia is to use bluetooth headset (in my case HBH-600) with SE T630 and my Compact.
T630 pairs with headset only during incoming or outgoing call, in stand-by mode my headset is absolutly free to connect to my Compact.
And since my Compact connected to handsfree it's not letting it go. Even when my device is turned off headset remains connected to it. On the one hand it's good, but in order to make headset work with two devices I should get rid of that feature.
I've seen a thread where people (with feature mentioned above) said that our devices don't think that answering a call is "using" the device and turn off. So other party of conversation couldn't hear anything.
Do you have any ideas how to break bluetooth connection with headset after call?
Thanks in advance.
Perhaps Pocket Bluetooth Tools will help you, it can auto-off the BT on the device after the call is complete and re-enable it when a call comes in.
Be aware, however, that some people find it can cause more problems than it solves - I however love it on my Xda II.
Thanks for tip.
I've tried that a long time ago, but found it of no use for me at that moment.
I remember that there is "settings" for it, but now I can't find it.
And another question. On that site it is said that program supports bluetooth handsfree and headset profile, and what about voice dialing?
you also can use Pocket Zen Phone.. schedule your profile to set the bluetooth off at certain time.
Hello,
I have been reading extensively this extremely useful forum to tweak and set up my newly acquired Kaiser but I now face a problem:
I own a Creative CB8100 Stereo headset (without hand-free) and I am trying to have it connect automatically to my Kaiser.
The only way I managed to connect the two together is, in the Bluetooth settings on the Kaiser, by tapping on the headset name (CB8100) and choosing "Set as a stereo headset". This is quite a long procedure and I would like to know if there is a way for this headset to connect automatically once turned on. In the worst case, is there a shortcut I could put on the Today screen to manually connect to my headset?
Thanks,
Bhangraman
Nobody got any idea on how to simplify this process?
A thread in one of the other forums suggests that making your Kaiser discoverable may help. Give it a try.
I am afraid it made no difference
Could you please link me this other thread you are talking about?
Here's the thread.
Thanks a lot
Installing A2DPToggle which provides an on/off button on the home page solved my problem.