Related
Well, that's weird. My friends new XDA 2 is acting up. He lost his soubd trough speaker couple of days ago, and then it came back. Today it happened again. I have no clue what's going on, hard reset didn't help. Any suggestions?
TIA
Has he been using hands free headset? If its anything like the xda 1 the connecter is very problematic and prone to problems.
Yes, very frequently. Looks like that's it. He connected and disconnected couple of times again and now it works.
Hello everyone...
Well, I'm another victim but in this case my MDA2 is muted but not deaf...
I'll explain... Most people with this problem have said that they can't hear nor can be heard when they have this headphones plug problem (i.e. The plug when inserted got the contacts stuck so the system thinks the plug is still inserted).
But in my case the other party DO hear me (this is without using a headphones) but I can't hear them or the system sounds, music, etc. but when I plug my headphones I can hear all sounds with no problem.
The day it failed it was all of a sudden, no water, no bumps, no nothing... actually I was not even using my headphones, so the jack it's out of the equation...
Any ideas?
Well as a matter of fact, about three weeks ago I dropped my MDA2 to the pavement and it scratched the case a bit, but it was working fine for the last three weeks...
Do you think this may be a retarded symptom of the accident three weeks ago?
I'm starting to think the speaker failed or got unsoldered...
Any ideas?
Thanks!!!
Rayan
hi Rayan
i had the following problem: i couldn't TURN UP the volume.
i could move the volume slider, but when i took another look to see if the device did really set the slider to the volume i had set - nada - zero.
volume was down again.
if you encounter the same problems: make it short and give your device a COLD reboot. that was the only thing that did help and gave me back audio.
regards ize|man
Hi izeman,
Well, I even performed a hard reset to factory defaults and nothing!!!
And because of that I'm sure it's a hardware problem...
I just hope it's a simple fixable hardware problem... I'm just wating to get in touch with the guy's at gsmphonesource.com (I have sent SEVERAL emails and voicemails and no one has contacted me back!) :evil: (nice customer service huh? :? )
Well I'll let you know how this story ends... :roll:
Thanks,
Rayan
WHOOOHOOO!
I fixed the problem!!!
Since the guys where I purchased my MDA2 NEVER returned my calls and emails, I got desperate and fix it myself!!! (I know I void my warranty, but it was useless anyway since those *&^%$ guys refused to take my calls)... :evil:
Anyhow, I carefully opened my MDA2 and got all the way into the speaker (which is actually encased in a module with two small gold plated connectors on the top) and cleaned them both, on the speaker module and the motherboard where two matching springs are located. I even carefully pulled the springs to give them a little more "pressure" when assembled.
Well, what can I say... I'm very happy to have my sound back!!!
If someone want to go this route, please let me tell you that it was a pain in the buttocks just to pry open the casing, but now I know how to do it, so drop me a line if you need any assistance... Maybe I will document the procedure with pictures once I have some spare time!... :wink:
(Now I can get rid of my stupid wired headset... It's amazing how those damn wires get to tangle so much!)
Best regards!
Rayan
Sound problems
Hi Rayan,
Good to know you fixed it - I have exactly the same problem; speaker only works intermittently. :evil:
I'd like to take to up on your offer to provide further details; especially how your opened the case without damaging it. :?:
cheers,
Pete
XDA II, Scandisk 512Mb, Plantronics 3000[/quote]
Rayan's fix...
http://forum.xda-developers.com/viewtopic.php?t=8525&highlight=sound+problem
hi guys..
I was watching a video clip and suddenly I see I can't hear any audio from it. I was surprised.. I tried to soft reset it couple of times... but with no luck... I couldn't here any tap sound or even when the phone rings.. nothing sounds.. and finally I did hard reset... but in despair.. still the same problem. but when I try to shake my jam. I could feel something moving.. i don't know if any bit/piece is disconnected.. when i try to tap it hard at the speaker.. i could hear to the music and after few seconds.. its stops.. again..
Has anyone come across such a problem.. I think probably my speaker needs to replaced.. any suggestions or solutions to this..
I would await for ur replies.
kindly advise..
thanks
Iffu
i have the same problem to. Please Help!
This is a "common" problem with the Magician. Mine had it as well. I sent it for repair since it's still under warranty. Some ppl had the guts to open it and fix the loose contact themselves. So if you're not a techie just take it to your service centre for repair :-(
No sound?
Hi. i had a similar problem some days ago. no sound at all from my magician. i've discovered that the problem was that my magician thought i had headphones conected. a simple insert of a headphone jack and removal brought my sound back to live. No problems since than.
Just a gentle few bangs did the trick
After reading several suggestions and info about the speaker problem, I tested my 02 mini with a song. It played ok through the speaker. So the speaker works, but appears to not "Switch" on when being used as a phone. Anyway long story short - I hit the corner of it into the palm of my hand a few times and da da it works again. I also blew through the speaker hole. Someone mentioned that somewhere as well. Hitting into my hand seemed to provide enough impact without creating any damage.
Had same problem too, and sent it away for repair. Three weeks later and the repair company are sending me a replacement this week as apparently they were unable to fix it!
Fault appeared without any warning and I had been using the phone pretty heavily all day. All I hope is that the replacement will have a newer ROM installed to save my ineptness from screwing up an upgrade.
This Jam is a peice of shi#e. I bought one in February, had various problems with both speakers - regular earpiece was unclear and speaker phone was just too damn low in volume.
Some people claimed this was an exception, or that it was the ROM or whatever. Right......
Finally sent the Jam back for warranty repair in May- there were many other defects with the phone that accumulated. I had bought insurance as well so I told them to just replace it. The seller admitted that this (audio/speaker is a common problem in this phone)
I just got the insurance replacement today - yep ages later. This one has firmware 1.11 WWE.
Guess what: the speakerphone on this one (brand new replacement) doesn't work - at all. Not at all. This is brand new, out of thebox. Incredible....
What is worse is that I am going on a month-long trip in a couple of days, so there is no way I can get another one - and by the looks of it, even if I got a replacement, the chances are that it too is a piece of ****#e without a functional speakerphone. This I-mate Jam (or whatever the 50 name sit goes by) is just a low quality piece of garbage.
HTC/I-Mate is garbage company. There is no chance in hell I will be buying any future Jam or I-mate phone.
Hey all First post, w00t.
New to the PDA type phone thing and learning what i can from here. Dont quite understand WM5 yet but i'll get it eventually.
nice fourm you all have here
A few post have hit the nail on the head with issues with the phone.
No hinge LED's when the phone rings is my main hate at the mo i think.
Also anyone know how to get media player to play videos in full screen? all it does is puts a black border round the video rather than streching it. This would be cool
Whats the differance between the o2 (or different) and corporate install type?
Also TomTom M5.2 is coming up all green lines, had a quick search and cant find a fix. Anyone?
Thought i'd drop on and say i've had a problem with my screen (gotta love us being beta testers ehh?) Only got the phone at chrimbo and woke up the other morning to find that the screen wouldnt tap. It seems that the screen is now tapping itself randomly, closing applications and not letting me use the touch screen at all. You cant reallign the screen.
Seems a few people have had this problem and it seems un-fixable, soft, hard resets and reinstalling the ROM doesnt work. pulling the battery out and leaving it for a short while seems to cure the problem for a short while.
If you're having this problem, call the retailer and have it replaced. Defo seems to be a hardware issue, maybe a bad batch?
I'm waiting on them getting a new one in store for me.
HTH
JAmes
The screen issue does seem similar to the problem I was having.
Was on and off, but totally stopped responding early Sunday morning. Didn't start working again after numerous resets. Took it to the O2 shop today and it decided to start working again...
But they believed me, gave me a replacement and I've had zero problems with this one.
Seems like there may be some faulty ones about. Get it changed and hope they don't give you another faulty one
Hi all,
I need help,suggestions,anything with an issue I've had for a while. Since the time I started loading WM6 the screen has been randomly fading to white. I have LSVW latest rom 22/4 SE and 1.40.10 radio and 1.40oli although it doesn't matter what rom you load. I tried going back to WM5 and its better but now still fades to white as well.
on advise from oli and legolas I purchased a new battery but still have the same issue.
I have dropped my phone once which resulted in a crack to the right of the DEL/CR keys so could it be a HW issue and if you think so is it one I could open up the phone and fix?
Any and all help appreciated
IN FACT IF SOMEONE CAN RESOLVE THE ISSUE I WILL DONATE SOME CASH TO THEM!
test
Im updating to
LVSW 4-23 Full, Radio 1.40.30.00, SPL 2.10.Oli, IPL 1.04
seeing if any difference comes out.
This is not the first time this issue has been reported:
http://forum.xda-developers.com/archive/index.php/t-301003.html
The conclusion is that it's hardware related. It may be as simple as one of the internal ribbon connectors having a less than firm connection. It may be brought on my anything from physical movement or pressure to internal pressure if the device gats warm. However, it is possible that there is a failing component. IMHO, a case of take it for replacement/repair or first check connectors if your brave and not worried about a warranty.
Mike
mikechannon said:
This is not the first time this issue has been reported:
http://forum.xda-developers.com/archive/index.php/t-301003.html
The conclusion is that it's hardware related. It may be as simple as one of the internal ribbon connectors having a less than firm connection. It may be brought on my anything from physical movement or pressure to internal pressure if the device gats warm. However, it is possible that there is a failing component. IMHO, a case of take it for replacement/repair or first check connectors if your brave and not worried about a warranty.
Mike
Click to expand...
Click to collapse
HHmmm interesting thread .. the only issue i have out of that is the fade to white one.
Maybe Hardware .. i got the phone off ebay and now it has a crack in it .. so i dare say it isnt under warranty any more. (even though its a max of 6 months old).
It may also be software. I experienced the WSOD on my JASJAM when playing with the GPS-related DLL's. Once this problem appeared when switching on the camera. The screen would turn white and soft reset would not fix this, only power off/on would sort it out. Seems that the drivers do not reset (some of) the hardware to a known state on boot.
Had EXACTLY the same problem. Hoped it would be a software problem. Hard-reset a few times to no avail. Upgraded to a couple of the WM6 ROMs. No change. I did notice that when it was cool it tended not to happen, but after being on the phone a couple minutes or using the PDA for a while, it would do it AGAIN.
One weird thing I noticed was that if I did a Soft-reset and held down the Left Soft-key, I could "force" it to fade to white on start-up! VERY WEIRD.
I finally bit the bullet, and sent it back to Telstra to get it sorted. Didn't want to void warranty myself.
It has been just over 2 weeks since I sent it off, and They have sent this reply...
-------
-------
Hi
This phone is currently waiting on a part which was ordered yesterday. Some parts have already been issued but needs further repair.
Regards
Nadine
--------------------------------------------------------------------------------
From: LJ Boyd [mailto:[email protected]]
Sent: Friday, 20 April 2007 2:18 PM
To: ! TMS Customer Service
Subject: RE: Imate JASJAM Problem
Hello, I am emailing about an I-Mate JASJAM phone I sent for repairs early last week (tel # xxx ).
Can you please update me as to status of this repair, as the Telstra shop did not provide me with a second phone while I await return/repair/replacement of the phone.
Thanks,
-------
-------
So, I guess it IS a hardware problem. But then again, that kind of reply, sounds a bit "dodgy" as it doesn't seem to "technical" does it?
Hope this helps.
jyetara said:
So, I guess it IS a hardware problem. But then again, that kind of reply, sounds a bit "dodgy" as it doesn't seem to "technical" does it?
Hope this helps.
Click to expand...
Click to collapse
Their reply was not very technical - does not surprise me however. The people who repair these devices are usually faced with some component/connection/screen or a m/board that needs replaced. They often fail to take account of something as basic as the case pressing on the screen or other components - particularly when device is warm. So they replace the component they think is faulty and then discover the problem is still there. With this issue in particular I think that there are no faulty components just the case is a fraction of a millimetre too tight for the internal components and hence swapping out parts can have no effect. With this fault I advise people to go for a replacement not a repair if possible.
NB: This issue should not be confused with white screen that may appear after installing particular software or when an application crashes, or when the flashing of a new ROM goes wrong! The hardware issue arises most commonly when the device gets warm or put another way goes white after maybe 10 minutes of use and will continue to go white even after hard reset.
Mike
I have this same problem! =(
My phone screen recently (4-5 days ago) started to go white. I never saw this happen with my own eyes but when i picked up my phone and its sleeping i push the power button to get to an all white screen. I can hear noises when i touch the screen but no image other than white. I can solve this by removing the battery and putting it back in, then my scren works fine....its not verry often just like 1-3 times a day.
I want to try a hard reset but have a question first: My phone is unlocked by the ebay guy i got it from, will a hard reset lock my phone back to Cingular?
Next i want to try upgrading my ROM and Radio and anything else...im looking in the wiki for instructions on how to do this. Any help? What else shouls i upgrade?
Ive only had my Hermes for around 2 months so im new to much of this.
THanks!
I recently purchased a Used Imate Jasjam (Ex Telstra Australia) with this issue.
I pulled the unit apart, and reseated and pressed the Power and LCD Display Data Cables... attempting to ensure they were firmly fastened.
I then upgraded to LVSW's Latest WM6 Release.
I have had the Phone go to White once in that timeframe since. I brought it back by pressing the power button of, then one again.
I don't feel that it's really a "100%" Faulty Part... Because it works fine othertimes. It almost seems as if connections or a Data Cable has an Issue.
I'm intending tonight and using the Phone over the weekend to see if the issue continues to occur.
BAD NEWS!!
Well, got my phone back after a bit over 3 weeks I think? I kept ringing the repair center and emailing. Finally they said it was ready, and was sent back to the shop I bought it from. Rang the shop "no it's not here yet, we will ring you"... now the repair centre to the shop is a 20 min drive... on the 3rd, I rang again at 1pm and "no it's not here yet, we will ring you when it arrives." At this point I was really getting p*ed off. So I went to the shop, and demanded, and guess what was AT the Shop?!?!?!
Anyway, after 1 friggin day, I have lost the Red & Green phone buttons! As of tonight the whole bottom section no longer work, and the screen has gone white again.
The repair report listed 3 things replaced...one was a "bezel" another was a "poly" something. I will get the report a list the replaced bits if anyone likes, but their descriptions are kind of strange if ya ask me.
Anyway, I have to send the phone back for repairs again, which could take another 3 weeks +, which I think is completely PATHETIC OF TELSTRA, especially for the fact they dont give the same phone or even similar to "loan" while I wait for my defective $1300 phone to get "repaired"... (more like 'fiddled with' & "yeah, she'll be right mate"...
GRRRRR!!!!
My girlfriends phone was having the same problem. Try popping out your SD card and putting the phone into/out of sleep and see if that brings back a visible screen. Thats how we determined her situation was a hardware problem and not a problem with the rom.
jyetara said:
Well, got my phone back after a bit over 3 weeks I think? I kept ringing the repair center and emailing. Finally they said it was ready, and was sent back to the shop I bought it from. Rang the shop "no it's not here yet, we will ring you"... now the repair centre to the shop is a 20 min drive... on the 3rd, I rang again at 1pm and "no it's not here yet, we will ring you when it arrives." At this point I was really getting p*ed off. So I went to the shop, and demanded, and guess what was AT the Shop?!?!?!
Anyway, after 1 friggin day, I have lost the Red & Green phone buttons! As of tonight the whole bottom section no longer work, and the screen has gone white again.
The repair report listed 3 things replaced...one was a "bezel" another was a "poly" something. I will get the report a list the replaced bits if anyone likes, but their descriptions are kind of strange if ya ask me.
Anyway, I have to send the phone back for repairs again, which could take another 3 weeks +, which I think is completely PATHETIC OF TELSTRA, especially for the fact they dont give the same phone or even similar to "loan" while I wait for my defective $1300 phone to get "repaired"... (more like 'fiddled with' & "yeah, she'll be right mate"...
GRRRRR!!!!
Click to expand...
Click to collapse
Yes, sadly this is kind of predictable as I said in an earlier post in this thread:
http://forum.xda-developers.com/showpost.php?p=1233420&postcount=7
This is why, as I said, get a replacement not a repair if possible. My view is that the individual components are fine but connectors come loose or the heat generated causes pressure to be put on the screen etc So it's a problem with some cases and how the innards in some cases get squeezed. So off course changing the top poly board, connectors, bezel gasket, may by pot luck make a difference but is just as likely to make no difference at all.
Mike
Status Report:
After having my phone playing Video's Through the Night (My Way of a "Stress Test" to Generate Heat) I woke up the find the screen to be "almost completely" White.
Usually its gone completely, however in this instance I was able to see the icons through the whitewash.
I put the phone into sleep and back out and the Display is fine again.
Being that these phones are much easier to pull apart and put back together than my old JasJar I might to do some further experimentation.
I think the issue will have something to do with either one of the following
- Heat
- Pressure on the LCD from Parts Around it
- Faulty Ribbon or Power Leads to the LCD
My suggestions
- In the Case of Heat... I'll run the Same Test, with the Phone Directly in front of a small airconditioning unit I have.
- In the Case of Pressure, I'm going to look and see if I can place some extra Insulation Tape or Similar on the Phone to relieve this
- I wish I could find somewhere to buy the Replacement Ribbon Cables but I don't know where I can get them in Australia... any ideas?
VolarisPtyLtd said:
Status Report:
After having my phone playing Video's Through the Night (My Way of a "Stress Test" to Generate Heat) I woke up the find the screen to be "almost completely" White.
Usually its gone completely, however in this instance I was able to see the icons through the whitewash.
I put the phone into sleep and back out and the Display is fine again.
Being that these phones are much easier to pull apart and put back together than my old JasJar I might to do some further experimentation.
I think the issue will have something to do with either one of the following
- Heat
- Pressure on the LCD from Parts Around it
- Faulty Ribbon or Power Leads to the LCD
My suggestions
- In the Case of Heat... I'll run the Same Test, with the Phone Directly in front of a small airconditioning unit I have.
- In the Case of Pressure, I'm going to look and see if I can place some extra Insulation Tape or Similar on the Phone to relieve this
- I wish I could find somewhere to buy the Replacement Ribbon Cables but I don't know where I can get them in Australia... any ideas?
Click to expand...
Click to collapse
We wait to see. Mind you one guy on these boards found he could get half an hour from his device if he put it in the freezer for a while - so I'm not sure that air-con will be strong enough!!!
Mike
Well Results.....
After pulling apart the unit and reconnected, I think I found my cause to simply be excess pressure.
I've removed the "Black Plastic" Micro SD Card from its Blanking Plate.
Since I've done this... not one White Screen Whatsoever.
I don't use an SD Card, so the issue is resolved for me, however it is very interesting.
Could be Pressure or Heat (Small Hole Might Increase Airflow/Allow for Greater Dissapation or something)
Hi folks,
i've also small experience with this "white screen" issue and just wanted to inform you about it.
I got the device from my former boss who did already complain about this "white screen" issue on his O² XDA trion with original ROM. (honestly i did not really believe him due to my experience with couple of other devices so after i got the device i was just wondering - ok back to the facts).
I installed on Friday the Windows Mobile VI Pro - BLACK 2.5 Release and until today it was running (as far as i remember expect one time) nearly perfect w/o white screens. About 45min ago, i flashed the device with BLACK 3.0 Release and got until now about 5-10 times a white screen.
I assume this is not a hardware ONLY issue but indeed very strange.
I'll go back to 2.5 and will look forward if i get again the white screen or it'll be ok.
Cheers so far
FaCeOff said:
Hi folks,
i've also small experience with this "white screen" issue and just wanted to inform you about it.
I got the device from my former boss who did already complain about this "white screen" issue on his O² XDA trion with original ROM. (honestly i did not really believe him due to my experience with couple of other devices so after i got the device i was just wondering - ok back to the facts).
I installed on Friday the Windows Mobile VI Pro - BLACK 2.5 Release and until today it was running (as far as i remember expect one time) nearly perfect w/o white screens. About 45min ago, i flashed the device with BLACK 3.0 Release and got until now about 5-10 times a white screen.
I assume this is not a hardware ONLY issue but indeed very strange.
I'll go back to 2.5 and will look forward if i get again the white screen or it'll be ok.
Cheers so far
Click to expand...
Click to collapse
You are right to ask the question "is it hardware or software".
1
We know a white screens can arise if folk duff up flashing a new ROM.
2
We know there is a hardware caused white screen that comes and goes often when device gets warm.
3
But there maybe white screens caused by some kinds of crashing software or a buggy ROM etc
Crucially in terms of finding a cure will be distiguishing between these.
2 for most people is easy - take it back and get a replacement.
1 is a matter for the ROM upgrading and fixing boards
3 is a case of trying different ROMs testing 3 party software by selective installation until the problem starts or stops.
In your case I am worried that this is a number 2 device as it did sometimes get the problem before you flashed the ROM and now it's worse. It may only be worse because this particular ROM is generating more heat and consequently more white screens. (see explanations elsewhere).
I suppose if it's an occasional problem you might live with it but otherwise it's replacement at best and repair as a rather dodgy alternative.
Mike
Hey Mike,
well, before flashing the device with a custom ROM, in my opinion it was really difficult to use it.
By flashing it with V 2.5, it was very good usable and with V 3.0 it returned to become more unusable. Nevertheless, i upgraded 10min ago with HARD-SPL-V7 and it's running fine now (i've been wating with downgrading to V 2.5. If it returns to become unstable, i will downgrade to V 2.5 again.
I'll keep you informed.
yes for this particular "white screen" issue it will be useful to hear how things go - thanks
Mike
White screen - in my case definitely a hardware issue
Hi folks,
i was testing and playing around with my Hermes and today i found the problem (very funny because now i can't reproduce it anymore but just read ahead).
Today i was playing around and after pressing by accident on the case of the Hermes, the screen appeared disappeared and changed into white.
Please download the video i recorded from the attached link - you'll see that it was able to reproduce it by tapping on the case:
http://asuka.descipe.de/dphome/test/HTC_Hermes_White_Screen_issue.mp4
Please use VLC or MPC (additional codecs required) to watch the movie.
Honestly i'm not sure if this can be reproduced by anyone but this makes the whole situation much more clear.
Any feedback is welcome.
Cheers
Hello all!
First, thanks for an awesome forum! It has both helped me tweak my Wizard, and also get help when I have needed it.
Well, I have no choice now but to ask here. Last autumn, my warranty was almost up, and a wierd problem presented itself. The mic and speaker suddenly just stopped working! The sidespeakers still work, I think, because the phone rings when someone calls me. But the caller can't hear me, and I can't hear the caller. And there isn't a hint of sound in it, no static or noise, there simply is nothing.
As there were only a few days before the 2 year warranty was up, I ran to my dealer and turned it in. A few weeks later, the phone returned, working again. But now that I come to think about it, I don't remember if I got a replacement or if they actually repaired it... It looked a little like they handled it rough though, maybe it was another phone... Well, that's not important right now.
The same thing has happened again! Summary:
1. Mic & phonespeaker dead
2. Stereo speakers work under certain conditions
3. Wired headset that came with the phone works, both for calling and media
So it seems like a hardware problem. Please note, although I downgraded the phone to original, official Swedish Qtek 9100 ROM, it has been thoroughly tweaked and upgraded to a number of different WM6 ROMs - but all that has been working beatifully!
Still, what are the odds for the mic&speaker dying twice in a row, on different phones (i think the present one is a replacement)?!?
Question: Does anyone recognize this? Is there a possibility that it is software related, and maybe fixable? I have searched both the web and these forums but haven't really found any information on it.
ANY input would be greatly appreciated!
Additional information:
Qtek 9100 (Swedish), G3 model, WM6 upgrade successful (unlocked)
EDIT: There are no system sounds, which is wierd, because the phone can still ring. I thought the system sounds came from the stereo speakers on the sides of the device?
Hello all!
It is a glorious day to be alive!!! Or to have a fully functional Wizard, at least!
Lol - my topic isn't very old, and i reply to it myself with a solution (?). I Googled after the Wizard service manual, and found it right here on Xda .
In all honesty, i didn't do all that much. I just followed the disassembly instructions of the wizard about half-way through, to the point where you get down to the back of the motherboard. I poked and fiddled enough to locate the mic assembly, only to discover that the mic is soldered to the mainboard of the phone. So, i figured i'd just leave it be, because if the mic is really broken the motherboard needs to be repleaced, or a replacement mic needs to be soldered on there.
After removing A LOT of dust in there (honestly, i think the service center that had my device last time wasn't very careful with anything, even a screw was missing! ), i reassembled it. The flat cable running to the keyboard was also a little skewed, but that may have been me, anyway i corrected it too. Same with the speakers.
Long story short, after successfully reassmbling the phone, i fired it up, called my home phone and voila! I works!
Not much of a fix, as i don't really know what i did exactly, but dust, dirt and some bad connections/soldering may have benn the culprit.
All in all, i'm very pleased with my afternoon here. Thanks for stopping by .
epatnor said:
Hello all!
It is a glorious day to be alive!!! Or to have a fully functional Wizard, at least!
Lol - my topic isn't very old, and i reply to it myself with a solution (?). I Googled after the Wizard service manual, and found it right here on Xda .
In all honesty, i didn't do all that much. I just followed the disassembly instructions of the wizard about half-way through, to the point where you get down to the back of the motherboard. I poked and fiddled enough to locate the mic assembly, only to discover that the mic is soldered to the mainboard of the phone. So, i figured i'd just leave it be, because if the mic is really broken the motherboard needs to be repleaced, or a replacement mic needs to be soldered on there.
After removing A LOT of dust in there (honestly, i think the service center that had my device last time wasn't very careful with anything, even a screw was missing! ), i reassembled it. The flat cable running to the keyboard was also a little skewed, but that may have been me, anyway i corrected it too. Same with the speakers.
Long story short, after successfully reassmbling the phone, i fired it up, called my home phone and voila! I works!
Not much of a fix, as i don't really know what i did exactly, but dust, dirt and some bad connections/soldering may have benn the culprit.
All in all, i'm very pleased with my afternoon here. Thanks for stopping by .
Click to expand...
Click to collapse
hi epatnor,
I think the problem with your phone was a stucked microswitch in the 2,5 mm connector for the headset. I read about it here in the forum. Sometimes the switch stays in the closed position and the phone still thinks the headset is connected. Thats why all the sound is sent to the not connected headset and therefor your phone seems to be not working (unless you connect the headset)...
But removing the dust is for sure not a bad thing...
For the next time: I think there was an easier solution for this problem than disassembling your phone...
regards
huibuh_1
Thanks huibuh_1,
Yes this was probably not the smoothest way of "fixing" it. That said, the stucked microswitch theory would actually fit my problem well - I can see now that the exact problem I was having would arise if such a switch was indeed stuck.
However, I think that the problem would be more intermittent since I actually use that port now and then - especially since it's the only way to talk (besides using a bluetooth headset that is). And since I connect the wired headset now and again the switch is used and moved, I suspect that this would result in the speaker/mic coming online again maybe..? Temporarily at least?
All the same, thanks for replying - this might happen again and with your information I'm better prepared for it!