accessing internet with wifi - MDA II, XDA II, 2060 General

Hi, ive got a netgear WG311 v2 pci adapter and have set up an ad-hoc network with my xda2 (scandisk sd card). I can connect to the pc and see pocket pc as a mobile device in my computer. But i cant access the internet from my xda2 while using the wifi. Ne suggestions??

make sure you wifi card have an ip
make sure if you use a proxy that it's set correct in the xda settings
make sure that the router open for the ip that the xda use

Exactly as Rudegar says.
As you can acess your PC, it would seem that you have an IP Address configured on the wifi card. Double check that you have the Netgear Wireless Point's IP Address configured as your default gateway on the XDA.
Rgds,
Rob.

Related

WiFi PPC > PC (detailed)

i got usb wlan adapter. it's ip is 192.168.1.130.
the lan adapter in my pc has 192.168.1.84 ip.
all computers on my local wired network has 192.168.1.* addresses and 255.255.255.0 subnet.
i fixed the IP of SD sandisk wifi adapter on my mda compact to 192.168.1.131.
Usb adapter is in peer-to-peer (ad-hoc) mode and i normaly connect with ppc to it. i got 80-100% signal all the time.
the problem/question #1: why i cant ping from ppc to PC ? firewall turned off.
#2 - if i could ping it, would i be able to ping all the other ip's on my wired network?
#3 - if i could be able to ping all of those computers, how should i set-up a workgroup on ppc and be able to map network drives through wlan link?
#4 - if i would be able to map the drive over wifi link, would i be able to add mine 20.000 mp3s to the pocketmusic's playlist and play them wirelessly?
thanks in advance!
And when i ping from PPC - i see on pc that "received" packets are raising -
ie. now it shows 12 packets received, when i run ping on ppc to pc, the
number increases to 16 (4 pings!) but all are time-outed....
And if the IP on both sides are set to "automaticly", they got assigned
169.254.*.* IP's. Then the ping goes through correctly but i can't still
access the network. The network bridge between LAN and WLAN connection only
made things worser, making my internet connection unusuable (DSL through the
same LAN connection) so i deleted the bridge. Now - ping is going but i
still cant map my pc's drive.... what could be the problem...
Same problem
Dakky,
I have the exact same problem. I bought a Netgear WG111 Wireless USB dongle. I created an ad-hoc network, connected to it but can't connect to the internet or browse my shared. On my desktop the sent packet go up but not the recieved.
Are we both being stupid, can't you connect your PPC to your PC using an ad-hoc network? I have now tried to connect with two different desktops to my XDA and a friends XDA IIs running WM5 to my desktop but had no success. I can connect to an access point and browse file/internet no problem.
I have an XDA EXEC and run XP Pro on desktop.
I've got similar problem. I have Linksys Wireless-G usb network adapter, i assign same class IP adresses (192.168.2.1, 192.168.2.2, mask 255.255.255.0) the wifi connects in ad-hoc modebut how can sync over wifi ?, if I am able to sync over wify i will be able to use my pc's internet connection wich is a lot faster than any gprs/edge
I don't think you can network in this way - basically you have a bunch of clients but no 'server' I think you need a wireless hub (with Internet connection in there somewhere) in there somewhere.
If you do a search on microsoft web site ther is some info about using a PC as an internet share for other PCs but you have to use a very specific IP address rnge for this and set the share PC up in a certain way

internet access through ad hoc wifi connection?

hi, im not able to connect to the net with my wizard.
i dont have a wireless router so am connecting directly to my laptop, the ad hoc connection i have made works fine for file tranfers, but not for activesync or connecting to the web in either PIE or minimo.
i know activesync isnt possible but surely i should be able to use the broaband from my laptop?
any pointers would be greatly appreciated. software? settings?
its a t-mobile uk vario with qtek test rom.
also anyone know of a remote control utility, i use logmein but would like something a little more menu/macro based for control of media.
cheers
kevo
Try turning on Internet Connection Sharing (ICS) on your laptop; that'll make your laptop act a bit more like a router, providing NAT services to the Wizard.
yeah i've tried that, and i've just tried bridging connections (dont really know much about that) but that hasnt worked either.
kevo
My configuration
Me too, I use ADHOC connection for my WLAN.
PC configuration:
ADSL connection shared
Adress IP:192.168.1.1 Mask:255.255.255.0
PocketPC configuration:
Adress IP:192.168.1.55 Mask:255.255.255.0 Gateway:192.168.1.1
DNS:80.10.246.2 for Wanadoo
Your problem is certainly the DNS.
You can put 192.168.1.1 too.
so it is possible? cool!.......but im still having problems.
i cant figure out how to enter these settings, not to sure where to put them,
iv tried puttin the DNS in the -> connections -> vpn
and -> network cards -> networks adapters -> SDIO WLAN Wireless Adapter
sorry to be a pain, but could you point me to where to get each address and where to put them?
also is there anything particular you did to set up the adhoc network? i just used the Windows XP wizard and then ticket the AdHoc option after.
my laptop is conected to the router and the router is connected to aol adsl.
the ip address of my laptop is showing as a simple 10.0.0. number on the LAN but "Autoconfiguration IP Address. . . : 169.254.235.147" for the WLAN
none of my setup has a static ip address, could this be causing the problems?
thanks
kevo
It's more hazardous without static adress but it's can work.
My PC has directly access to the Internet with a ADSL modem.
It's here (network cards -> networks adapters -> SDIO WLAN Wireless Adapter )
Apparently, it's ok for your PC and the Ad-Hoc mode.
Maybe, you should have your adress IP WLAN on the same network adress of your router.
I GOT IT WORKING!!!
I started again from scratch.
set a new WLAN. added new setup to the vario, added the DNS etc to the vario.
the problem i was having was the way i was sharing the internet connection, i was trying to shared the internet from the wireless to the lan rather than the internet from the lan to the wireless (if that makes sense to anyone!!!). i also ticked all the connection sharing services to allow them, just need to go through them and see which i dont need now.
thanks for the help guys
kevo
(its showing my transfer rate as 11Mbps, although i think iv done the G tweak and my laptop says its got a G card. what speeds should i be getting?)

wifi problem

ok heres the deal... i have a MDA flashed with the software from att for the 8125 everything works great except when i turn wifi on, i can connect to the network but cant ever get a page to work. does anyone have any suggestions????? please help
Is this happening on any network or your home network?
Check this... go to Settings - Connections - Network Cards. Make sure the WLAN Adapter is set to connect to the internet. Then tap the WLAN Adapter and make sure IP Address is set to Server Assigned then in Name Servers you don't have anything. If any of these is different, change it to the above.
Yeah. I have the same problem. I have wifi pci asus, the signal is good. I have Lan tru router and now bridged connection. I set the ip, mask and gateway which are in the status of the brudge. And the internet explorer and opera wont load pages.?!??! dns isnt set.
The network adapter is sdio wlan.., and the connection is my work network in connection > connections > advanced >select networks.
i use wm6, nbd 8.0
What could be the problem???
it is home network and all other wifi locations
i know there is a problem with secured networks, especially with wpa encryption. try to remove the encryption and see how it goes....
I have removed all encription. I tried preety much everithing and it doesnt work. All other free wifi networks work just fine, i can surf on internet.
what router do you have? i know that i could not connect to a 3com router with the wizard with any rom i tried.
try using a defined ip address and dns, meaning no dhcp. use a real dns addresses and not the default gateway...

Internet Connection Sharing Problem

Hi, i need help about connecting my Pocket PC and using ICS
So this is what i want to achieve:
1. I have internet connection on my laptop via LAN
2. when i connect my HP IPAQ 114 with usb cable and sync using Active Sync i have internet on my PPC
3. I have another laptop that i want to "give" internet to via my wireless card on PPC connected wireless-ly to Laptop2
4. This is the scenario i like to create:
http://digitanium.blogspot.com/
Can someone help me with this?
I do the same thing as my curent internet is from a usb modem
so i turn on internet sharing on my pc
and set my phone's ip to be on the same subnet in my case 192.168.0.X
set my gateway to the ip on the pc in my case 192.168.0.1
set my dns to the same dns the pc use
if you don't know your dns
you can get it from a console and typing
iconfig /all
on your pc
tnx but i tried that and then i don't have internet on pc1 because of the mac of it is my password to the internet provider
can i somehow fis that?
ok i set my Local connection1(internet) to ics to the local connection 4 (activesync created and it made its address 192.168.0.1)
this seems to be normal but now my active sync can not connect to my device
and my laptop1 ip must be 10.10.16.79

View and access network PC's over wifi

Hi
Does anyone know how to do this?
I have tried with total commander and many others.
Has anyone got it working?
my purpose for it is streaming music from my pc and accessing documents and saved web pages etc.
P.S. I can connect to the internet over wifi, but not access any PC's on the network.
I am using the latest SE build R2
thanks in advance
its working just fine for me using total commander and gsplayer!
just using the //PC_NAME works perfectly in total commander. In fact, I`m using it right now!
hey i use the htc network plugin works just fine for me, i got a domain network with a win2k8 server and i m able to access all files on it streaming is also possible..
install and soft reset afterwards you got the network entry in settings/connections/NetworkPlugin where you can add computers which you can access afterwards with file explorer
Fabian1112 said:
hey i use the htc network plugin works just fine for me, i got a domain network with a win2k8 server and i m able to access all files on it streaming is also possible..
install and soft reset afterwards you got the network entry in settings/connections/NetworkPlugin where you can add computers which you can access afterwards with file explorer
Click to expand...
Click to collapse
Thank for this app.. works like a bomb!
nice to hear, that it works for you
Hi can you use this appplication to also access the internet via the pc's internet connection e.g. if pc is on a landline and xperia connects via wifi to the pc I want the xperia to be able to use the internet as well ..
do u know?
use a vpn connection to connect to remote network then the plugin should work with this connection and find the computers from the vpn network.. hope you understand what i mean
i am using bulletproof ftp and resco explorer.. resco explorer got possibility to add ftp connections.. so you have just to add port forward to your firewall and to connect to ftp.. if using a single server where all files are stored on it is a very nice alternative to share all things via ftp because you can access it from anywhere.. you need a dyndns hostname or something similar too, but i guess i dont have to say this
i use logmein and the cab works fine for me, i fix customers pc's from the x1 and they pay me for doin it via paypal
still no luck
ok
thank for the help so far
i am feeling really stupid.
i installed the network plugin. then reset and connected to my wifi network at home.
now I try add new or browse and it keeps saying map drive failed or no computer was found in the network.
Could it be my wireless network settings?
I am able to connect to the net
the Ip address is inline with that of my pcs and all the PCs can see each other.
I do not have a domian or VPN setup
Please help.
What am I doing wrong?
I have tried pinging my phone and it works, but if I try ping my Pc from my phone it doesnt work. I am using vxutil
I've been playing around and i noticed that I can ping my phone from my pc but i my phone cannot ping my pc ( doesnt find it). i am using vxutil
any firewall on the host pc? How do you try to connect? Through Hostname or with the ip,.. ? Never had such a problem but you can try to add the drives without browsing by just adding them with the path for example
//mynetworkpc(better you use the ip instead x.x.x.x)/sharedfolder
i think it should be a problem of your host pc i guess.. can you access it from other network computers? Try to ping it from another computer in your network, sounds like a firewall problem to me
Here is what I can do
1. Ping my computer and any other computer from any computer connected to both wired and wireless network
2. access the files on my computer from any other pc in the house
3. stream music to and from my pc to any pc in the house
4. ping my Phone from my pc
5. connect to the internet though the wireless network, using my phone.
What I cant do
1. ping my pc from my phone
2. connect to shared files on my pc from my phone
Let me know if there is something I am doing wrong or any settings to check or anything else I can do to get this working please
I found out some more info that might be useful
it has to do with IP addresses of the phone
Current IP
XPERIA
169.254.2.1
Adapters
NE20001 - NE2000 Compatible ethernet driver
IP Address : 0.0.0.0
TNETW12511 - IEEE 802.11b/g Compatible Wifi adapter
IP Address : 192.168.11.4
Subnet Mask : 255.0.0.0
Default Gateway :192.168.11.2
Primary DNS : 192.168.11.2
DNCP Server : 192.168.11.2
Now my pc's IP address is 192.168.11.9
My routers IP address is 192.168.11.2
Should I be changing the Current IP address?
I found out some more info that might be useful
it has to do with IP addresses of the phone
Current IP
XPERIA
169.254.2.1
Adapters
NE20001 - NE2000 Compatible ethernet driver
IP Address : 0.0.0.0
TNETW12511 - IEEE 802.11b/g Compatible Wifi adapter
IP Address : 192.168.11.4
Subnet Mask : 255.0.0.0
Default Gateway :192.168.11.2
Primary DNS : 192.168.11.2
DNCP Server : 192.168.11.2
Now my pc's IP address is 192.168.11.9
My routers IP address is 192.168.11.2
Should I be changing the Current IP address?
I use Resco File Explorer2008. It sees my Vista x64 pc on my wireless net without a problem. I can map and explore any shared drives on it.
I also use a app called Iper. It sees all my net devices and pings them without a problem either??
Stuart
festeradamz said:
i use logmein and the cab works fine for me, i fix customers pc's from the x1 and they pay me for doin it via paypal
Click to expand...
Click to collapse
You have logmein working from the X1? if so, how did you get this to work. This would be really useful for me
Ok I have installed IPer
I have noticed again the IP address for RNDISFN1 is 169.244.x.x and the Ip address for my network is 192.168.xx.x. could this be the problem and if so how do I change this IP address ( the phone)
I really want to get this working and all help will be greatly appreciated!!!!!!!!!

Categories

Resources