I just recently picked up a Targus Stowaway keyboard
(Model# PA 840)on ebay pretty cheap, I also picked up an adapter that converts ipaq 3600 series accesories for use with an XDA, I have the Siemens SX56 att version.
So I installed the software for it and the keyboard actually works great with the adapter plug, but I noticed that if I power off the XDA or if I leave it to power off by itself I can never turn it on again untill I do a soft reset , as soon as I uninstalled the software it works fine again.
Has anyone encountered this before????
I have been on their website and I have tried installing different versions of the software , but still it's allways the same problem??
Can anyone help me?
Under settings/connections make sure "beams" is unchecked, it might help.
thanks
it workes for me
Related
i am not really sure which section of the forum i should post this in
Hi there
I am due for an upgrade on my t mobile contract so I was going to go for the MDA 3,
I have tom-tom software waiting ready to install on the MDA 3 as soon as I receive it, I have just had delivered today the holux gps receiver cr-100 that fits the MDA 3,
I have since noticed that the MDA pro is available and what I am wondering does anyone know if the tom-tom software is likely to work on the MDA pro and will the cr-100 car cradle that I have bought work with the MDA pro as well
This will be my 1st phone of this type so I am not really sure of the ins and outs
Any help great or small will be appreciated
can someone tell me if i have posted this in the right catagory please
The best thing to do is speak to the TT support peeps to clarify whether it is compatible with WinCE 5.01.
The holux gps receiver cr-100 will not fit the Pro because they have done away with the port connector they used to use on the mda3 and replaced it with USB.
I find the good thing about the Pro is that you can just flip it open and sit it in front of your dials without obstructing your speedometer. This also helps with the sound, it appears to sound a little clearer when positioned in such a way.
The only bummer is that if you have the adapter plugged in it doesnt sit as nice but the tablet style screen soon sorts that out.
I would go for the pro if TT is compatible.
The MDA3 was never really supported very well but it did have pocket mesenger and xbackup which are both sorely missed on the Pro.
cheers thank you, thats a great help i guess being as i have paid for the other stuff i will stick with my origional thinking and go with the mda iii,
Hello friends,
My firts contact with this forum.
I have one question. Palmone Universal Wireless Keyboard don't work with Prophet, s200, etc..??? Help please . Anybody has an special drivers??? The PalmOne UWK drivers don't work.
Isn't this thing infrared? If so, make sure it lines up nicely to the infrared of the S200. Also make sure that your 'receive all incoming beams' function under SETTING->Connections->BEAM is turned on.
I guess you found the drivers here?
Also try searching the forums here (complete forums, not just prophet) for more posts about this keyboard. I'm sure there are some.
I tried this Keyboard on the Prophet. It doesn't work, but it works on the Blueangel w/o hassle.
same here. I bought the palm universal wireless keyboard thinking it'll work with the prophet since it's wm5. No luck.. =(
It's too bad cause I got the keyboard really cheap...
Anyone have a driver? The ones from the HP site don't seem to work
I have the same problem. The HP BT foldable keyboard software doesn´t works on Trinity. Does anyone know a .cab or program to connect this keyboard on the HTC P3600?
Same problem here. Six months I am trying to find a driver for Trinity. Unfortunately no joy till now. I hope that you will be more lucky than me.
Regards!
I am using the drivers that came with the disk, big problems with key repeat. Is that everyone elses problem?
I'm planning to get a bluetooth keyboard for my Kaiser.. will any of the bluetooth keyboards work? or would I have to get one that is specifically for PDAs..
Sorry for such a bump, but I didn't think this required a new thread.
I am also wondering if it is possible to use a Bluetooth keyboard with the Kaiser.
anonova said:
Sorry for such a bump, but I didn't think this required a new thread.
I am also wondering if it is possible to use a Bluetooth keyboard with the Kaiser.
Click to expand...
Click to collapse
A friend of mine works for a UK company who are trying these out:
http://www.just-mobileonline.com/products_communicationseries_2.html
She sent me one recently and it seems to work OK with my MDA Vario III
I've been using the Freedom Input Universal keyboard with my Tytn II. It supports the BT HID profile, so no drivers are needed.
My ThinkOutside (now iGO) BT keyboard works perfectly with my Tilt.
http://www.igo.com/product.asp?sku=2524884
Anyone used the BT laser virtual keyboards?
http://www.thinkgeek.com/computing/input/8193/
http://www.youtube.com/watch?v=HzDrUU5n_fQ
It even made it on CSI...
Hi,
I'm a newbie and would like some help pleeease!
I have a jasjam that is running wm6. I bought an iGo Think Outside portable bluetooth keyboard and mouse. They do not support Jasjams... but someone had downloaded the Jasjar driver and installed it and everything worked fine (http://www.mrgadget.com.au/2007/05/imate-jasjamdopod-838-pro-stowaway.html). The only thing is that his jasjam was probably on wm5 judging by the date I went ahead and bought the keyboard and mouse thinking I could download the jasjar driver and be able to use them but I can't get them to work (it only gets up to step 5 in the manual)
Just wondering if anyone knows how I can get my keyboard to work on wm6? I wrote to customer support and they can't help because the keyboard is now discontinued and they won't be releasing any new drivers for wm6
Thanks and looking forward to hearing from anyone